Search Documents

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By E Jak, P Hayes, J Chen

The paper provides an overview of the various analytical and microanalytical techniques currently in use to characterise the outcomes of pyrometallurgical processes, examining the advantages and limitations of these approaches. Specific focus with be given to quantitative microanalysis techniques including electron probe microanalysis and laser ablation, covering general principles, capabilities and limitations and recent development to address specific challenges associated with analysing molten slag, matte, and alloys, highlighting the necessity of embracing the application of these and other innovative analytical methodologies.

Jun 19, 2024

By W. H. Hodgson, A. R. Preston

"Improved rail production techniques provide new options for the rail user. Steelmaking improvements offer tighter composition control, lower oxide and sulphide counts, greater control of segregates and freedom from hydrogen problem s. New ultrasonic, laser and eddy current equipment gives printout information on surf ace flatness, straightness and internal condition. These have come along at a time when dramatic changes have occurred on the rail heat treatment scene. Rails can now be deep hardened on or offline in ways which should eventually result in a complete rewrite of the world's specifications. Rails of simple composition can be produced in the hardness range 2801400 BHN as required. The rail user can choose the hardness within this range according to requirement without the necessity for any step changes in the process routes.It is suggested that this is the pattern f or the next decade.IntroductionRails have been the subject of very slow improvement over many years but developments gathered momentum in the early seventies. Recent improvements in quality and properties have provided dramatic increases in rail life under the more severe service situations. Rail profile grinding, lubrication and other track improvements have greatly added to expectations of even longer life. All of this, coupled to even newer mill heat treatment developments, tilt both technical and economic advantages away from tradition to the point where specifications will need to be rewritten so that railroads can take full advantage of these new products."

Jan 1, 1988

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By Maurizio Massimo

Danieli developed the “3Q” suite of process control technologies to address three critical principles: delivering the highest product Quality, in the required Quantity, with Quickness of response required for today’s casting machines. Ever increasing market demands for productivity and slab quality necessitate the latest advances/improvements in equipment design, process technology, and control software for all types of slab casters, and Danieli boasts a unique experience that extends from ultra high-speed thin slab casters to extra high-thickness conventional slab casters. The “3Q” system is monitored and controlled by a unique, intelligent HMI incorporating. Touch screen technology and Operator Assistant tablets. Operator Assistant is a tablet based system that guides the operator through the plant process, so that in the event of a process change or an alarm the operator is automatically presented with the choice of possible solutions / actions. The comprehensive range of technological packages cover all aspects of caster design and automation control, from feeding of liquid steel into the tundish to the final slab leaving the caster.

Aug 17, 2017

By J. E. Johnson

OF the many items of information necessary to the successful management of the blast-furnace, few are more important than knowledge of the location and movement of the stock-line: whether the furnace is full and has. been kept so; whether the stock is settling regularly or slipping; and, if slipping, how often it has slipped, at what times, and how far at each time. To obtain these data, a man is sometimes stationed at the top of a. pair of mechanically-filled furnaces, simply to watch and gauge them by hand in the old-fashioned way. - A more recent practice is the suspension of test-rods from ropes leading over pulleys to the ground-level, where the ropes are wound on small drums with graduated peripheries and provided with crank-handles, whereby the skip-man or some other person can quickly and conveniently gauge the position of the stock-line in the furnace. I believe the credit for this great improvement belongs to Messrs. McClure & Phillips of Sharon, Pa., who were, as far as I know, the first to apply it, and who have a patent for it. The valuable indications gained by application of the Uehling pyrometer to the down-comer are Dot to be ignored; but the information thus furnished is somewhat indi¬rect, and there is no scale for the translation of "top-tempera¬tures " into " feet down." Moreover, this apparatus as a whole is delicate, and the cost of its installation and maintenance is high. If the record furnished by the Uehling pyrometer is not in the most desirable form, the test-rods, on the other hand, give no record at all, except through the memory, or notes of a man who, to say the least, is not gauging continuously, and who may omit to report an improperly low stock-line, if it be due to a fault of his own.

Mar 1, 1905

By Kirtland Marsh

THE manufacture of gas masks by the Chemical Warfare Service, U. S. A., required preparation of the carbon used in the canisters. The largest plant for the production of this carbon was situated at the works of the Astoria Light, Heat and Power Co., at Astoria, N. Y.; this paper will deal1 with the pyrometry equipment at that plant. Commercial charcoal was found unsuitable for use in gas masks because of its low power of absorption and its poor resistance to abrasion. The best raw material for the production of carbon was found to be coconut shells, but any kind of nut shells or fruit pits were used when sufficient quantities of coconut shells could not be obtained. The shells were first carbonized in retorts, the carbon was then crushed and screened between 8 and 16 mesh, and finally submitted to a special heat-treatment in air; steam treatment was later substituted for treatment in air. The production of gas-mask carbon on a commercial scale was begun at Astoria about Aug. 1, 1917. Temperature control was essential during the initial carbonization of the shells, as well as during the air or steam treatment, and pyrometers were installed for this purpose. The installation and maintenance of all pyrometry equipment was done by the pyrometry department, consisting of an officer in charge, an assistant, and two men. A special pyrometry laboratory was maintained in which all repairs were made.

Jan 9, 1919

By O. C. Blade, Elizabeth Hughes

Conservation in the utilization of any product is always subject to improvement if the composition and properties of the product are known. Petroleum is no exception, and knowledge of the characteristics of crude oils, even when given on the broad basis of routine type analyses has proved useful to chemists, engineers, and geologists in improving pro- duction and utilization of petroleum. For a quarter of a century the Bureau of Mines has sought to provide such information regarding crude oils and has analyzed many samples of petroleum by its standardized rou- tine method. Most of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published up to January 1, 1948. The routine method used for all these analyses is basically the same as that described by Dean, et al.. Briefly, the procedure consists of testing by standard methods, small samples of a crude oil for gravity, sulfur, color, and viscosity, and of distilling a sample of the crude oil by a standardized procedure and determining certain properties in the sep- arated fractions and residuum. Careful records are made during the proce- dure, and the distillation data obtained are used to calculate the approx- imate amounts of products present in the sample such as percents of gas- oline, kerosine, gas oil, and lubricants. The data obtained are recorded on a standard analytical report form. An analysis of a sample of typical midcontinent crude oil is shown in table 1. Compilation of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses are often shown in connection with other studies, such as engineering field reports. This bibliography is a compilation of references to 115 publications, which contain analyses of crude oils by the Bureau of Mines. References may be found to analyses of crude oils from the United States, Canada,

Jun 1, 1948

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By Zhiyuan Ma, ZUI WANG, Xincheng Hu, Jianwei Cheng, Junhong Si, Yi Qin, Gao Ke

The harmfulness and destructiveness of mine gas explosion is quite serious, which is the first of all kinds of coal mine disasters. Once the gas explosion occurs, it could instantly generate explosion shock waves, high temperature airflows, and disaster gases, which cause the destruction of underground ventilation structures, disruption of airflow direction in a mine ventilation network, and miners’ deaths by asphyxiation. As an important barrier to prevent the spread of accidents caused by the gas explosion, the safety and reliability of the mine seal affects the mine’s production and the health of workers. Due to the demands of coal mine production and transportation, a large number of longitudinal and horizontal roadway networks have been developed underground. There are not only many flat and straight roadways in the complex roadway network structure, but also a large number of different types of bifurcations and bends. Once a gas explosion occurs, the impact of the blast waves on the mine seal after passing through the complex path is difficult to determine. Therefore, this paper establishes a numerical model of bifurcated and cornered roadways and studies how the impact of gas explosion shock waves on the structure of sandwich mine seal after passing through different types of bifurcated and cornered roadways. The damage state of sandwich mine seal is analyzed. The researching finding could prevent and manage the spread of gas explosion disaster, and improve the disaster mitigation of mine explosion accident.

Jul 11, 2023

By D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming mineral. A polymeric depressant is then added to attach to this re-surfaced mineral. Nearly 200 flotation tests with a 11 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother-collector system, grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1994

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, the National Institute for Occupational Safety and Health (NIOSH) conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the re-search, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This paper highlights NIOSH?s research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan and if appropriate training is provided.

Jan 1, 2009

By H. Laitala, M. Lampi

Metso Outotec has developed a wide range of solvent-extraction technologies over decades and has introduced Metso Outotec VSF®X solvent-extraction plant. Standardized and modularized, Metso Outotec VSFX Plant provides a novel way to design, manufacture, transport, install, operate, and maintain solvent-extraction plants far better than in the past with highly sustainable and safe methods. For the customer, this means fast-track projects with savings in means of time, costs, quality, and operation. Sicomines and Metso Outotec have together implemented and commissioned a modern and efficient copper solvent-extraction plant. Plant commissioning and ramp up of the plant were fast and the plant is now operating efficiently. This paper presents Sicomines’ VSFX copper solvent-extraction project and gives a sight into operating figures for the plant.

Jan 1, 2023

By Ørjan Nerland, Torgeir Haugen, Astri Eggen, Kjell Karlsrud

"Ground improvement by the deep dry mixing (DDM) method is used in Norway since the late 1970's. A brief review is given of the Norwegian guideline for ground improvement with DDM issued in 2012, but focus is on practical examples and experiences related to improving the stability of excavations and natural slopes in soft clays. Two examples deal with experiences from 10 to 18 m deep excavations in soft and partly highly sensitive clays, where DDM panels and block stabilization were used to both give sufficient stability against bottom heave and to limit lateral wall displacements. A third case deals with improving the stability of a natural slope in quick clay by installing DDM panels near the crest of the slope. To limit disturbance and excess pore pressures generated during the DDM works, vertical drains were installed in advance in between the DDM panels. This ensured that the excess pore pressures generated by the DDM works (up to 150 kPA) dissipated quickly, which was instrumental to avoid triggering a landslide during the stabilizing works.INTRODUCTIONThe lime column (LC) method developed in Sweden and Japan in the mid 1970's (e.g. Broms and Boman, 1977). Since then, there have been significant developments in Scandinavia and around the world in terms of rigs, mixing machinery and tools, and type of binders used. The method, presently named the ""Dry Deep Mixing"" (DDM) method in contrast to the wet deep mixing methods (WDM) that also have developed significantly over the past decades, e.g. Kitazume and Terashi (2013). The first application of the DDM method in Norway was in the late 1970's to improve the stability of an excavation in quick-clay, then using only lime as binder. Most DDM applications in Norway have also thereafter been to improve the stability of cuts, supported excavations or natural slopes in soft clays. The Norwegian Geotechnical Society (2012) issued in 2012 “Guidelines for design of ground improvement with DDM methods"". The following highlights design issues dealt with. The paper focuses however, on some practical cases where DDM has been used to improve stability of deep excavations and a natural slope in soft and partly highly sensitive clays."

Jan 1, 2015

By Whitmell J. Smithwick, Charles E. Dandois

The first operating unit of the ring or annular shaft kiln as developed by Mr. Karl Beckenbach of West Germany was rated 185 tpd and was installed in 1962. Today, there are approximately 84 units in operation in Western Europe and Japan. Twenty-one additional units are under construction or on order. Sizes range from approximately 100-330 tpd, however, units of over 500 tons are in the design stage. The ring shaft kiln is a single vertical cylinder to which are attached the required service platforms, combustion chambers, injectors and distribution piping (Fig. 1). Auxiliaries such as recuperator, exhaust fan and dust collector are mounted on the appropriate service platform. The charging pan, feed conveyor, etc., are mounted at the kiln top and at the bottom of the kiln is the silo with a vibrator type discharger. Mounted separately is the required blower for injector air and fan for internal cooling.

Jan 4, 1973

By M. W. Grabinsky, B. D. Thompson

ABSTRACT: Use of cemented paste backfill (CPB) offers economic and environmental advantages over other backfill methods. However, many operations have limited knowledge of how their CPB behaves in situ. Therefore, to avoid over-pressuring containment barricades, backfilling strategies necessarily tend to be conservative. In situ monitoring at Barrick Gold Corporation’s Williams Mine and Inmet Mining Corporation’s Cayeli Mine has been conducted and factors controlling barricade pressures are demonstrated, including rise rates, binder content, stope geometry, and tailings properties. The application of barricade pressure monitoring on a stope-by-stope basis can increase backfilling efficiency and, thus, reduce stope cycle times, while maintaining optimal safety.

Jan 1, 2011

By Shabnam Sabah, Geoffrey Brooks

In oxygen steelmaking, splashing and droplet formation play a key role in the kinetics of the process. Though splashing has been studied by previous investigators, there is only limited understanding of how different cavity modes affect splashing. Therefore, a cold model study (at various lance heights and gas flow rates) has been carried out focusing on the issue of cavity modes and how it affects splashing phenomenon. Analysis using Fast Fourier Transform (FFT) was carried out on cavity oscillation that showed that frequency and amplitude of oscillation was highest in penetrating mode. Measurements of splashing over a range of conditions showed splashing greatly reduced when cavities went from splashing to penetrating mode. The results were validated and compared with plant data and previous model investigations.

Jan 1, 2014

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965