Search Documents

By W. A. Lang

Introduction In this review, which is the fifth of the series on the Progress in Coal Technology, an attempt has been made to outline some of the more important developments that have taken place in coal carbonization during the last decade. Research into both high-and low-temperature carbonization has been active for three principal reasons: (1) the growing shortages in most countries of high-quality coking coals; (2) the demand for smokeless fuels for domestic purposes; (3) the need for metallurgical coke for the increased output of steel in the post-war years. The growing importance of coal tars as a source of chemicals for the preparation of synthetic products and of coal gases for the recovery of sulphur is evident. Many of the researches initiated because of wartime necessity have been continued .and even expanded in the post-war years. High-temperature carbonization with a suitable coal yields a strong coke which is used primarily for metallurgical purposes, a tar with good marketable value, and a large yield of gas of medium calorific value. Low-temperature carbonization gives a more free-burning solid product suitable for a domestic fuel, a high yield of a tar which is generally regarded as superior to high-temperature tar for chemical purposes, and a smaller yield of a higher-heat-value gas.

Jan 1, 1951

By D. J. Hains

IN this paper we shall examine the Why, Where and How concerning the agglomeration of iron ores and concentrates. Fig. l answers the questions @f why there is so much interest at the present time in the art of agglomeration. The use of sinter or pellets in the blast furnace has materially increased their rated •capacity. ':'President Hains Company Ltd. Engineering J. S. McMahon ( 1) reports an increase from 653 tons of .pig iron per day to 1140 tons of pig iron per day with the use of a 100 per cent sinter burden on one of his blast furnaces. In the United States the use of 100 per cent pellets has increased pig iron production from approximately 1800 tons per day to over 3000 tons pig iron per day (2). In our economic system the general objective is to produce more and better commodities cheaper. Fig. 2 shows the decrease in coke consumption with increased tonnages from the furnaces when using -

Jan 1, 1961

By D. J. Englund, R. A. Davis

"A three-dimensional CFD model of a straight grate furnace for indurating iron-oxide pellets was developed for exploring conditions of furnace operation for fluid flow, heat transfer and reactions. The model includes reactions for natural gas combustion in the gas phase and calcination and magnetite oxidation as well as drying in the pellet bed. The performance of the model was investigated with a series of pellet production rates that included adjustments to the fuel rates to achieve proper induration temperatures in the pellet bed. The model may be used to discover opportunities for process improvement.IntroductionIron oxide pellets are a feedstock to blast furnaces for iron making. Pellets require physical strength characteristics needed to maintain their integrity during storage, handling, transportation and smelting. Pellets are produced from iron ore in a series of mineral processing operations that form wet green balls from slurries of iron-ore concentrate with binders, such as bentonite, and possibly fluxing-agents such as limestone and dolomite. The green balls are dried, fired at high temperature, and then cooled in an induration furnace to achieve the strength and chemical composition required for efficient reduction and slag separation in blast furnaces. Induration furnaces are generally straight grates or grate-kilncooler configurations. These furnaces operate with pellet beds passing through a series of temperature zones to control drying and chemical reactions in the bed.Process air passes through the zones in an overall counter flow direction to the pellets for efficient heat transfer and energy recovery from the cooling stage. Consequently, the zone conditions and the overall furnace performance are highly coupled. Thus, it becomes challenging to predict how changes to any single zone may affect the rest of the furnace. To gain a better understanding of machine performance and coupling, a three-dimensional, steady-state model of a complete straight grate induration furnace was created using computational fluid dynamics (CFD)."

Jan 1, 2015

By J. D. Davis

THE CARBONIZING properties of Chilton-bed coal from Lorado No. 5 mine, HE Logan County, W. Va., were determined by Bureau of Mines-American Gas Association tests at 600°, 700°, 800°, 900°, and 1,000° C. and by expansion tests. Chemical analyses, agglutinating and plasticity tests, and low- and high-temperature assays also were included in the investigation. Blends with low-volatile Pocahontas No. 3 coal were carbonized at. 900° C. The Chilton coal bed lies in the Kanawha, or Upper Pottsville formation of the Pennsylvanian system; the estimated original reserves are nearly 3.2 billion tons. The bed was 39/1 to 57 inches thick in the Lorado No. 5 mine, and the coal was 38 to 57 inches thick. The carbonization sample contained 62.6 percent fixed carbon on the dry, mineral-matter-free, basis, and the heating value on the moist, mineral-matter-free basis was 15,190 B. t. u. per pound; it therefore ranks as high-volatile A bituminous. It contained 1.8 percent moisture, 35.2 percent volatile matter, 57.9 percent fixed carbon, 5.1 percent ash, and 0.7 percent sulfur, as carbonized. The sulfur was largely organic, and the ash softened at 2,630° F. The agglutinating value determined on a silicon carbide-coal mixture of 15:1 was 6.8. In the Gieseler test the coal softened at 327° C., fused at 407° C., attained a maximum fluidity of 5,730 dial divisions per minute at 435° C., and solidified at 487° C. Maximum resistance in the Davis plastometer was 45.5 pound-inches.

Jan 1, 1951

By J. R. Hauger, P. A. Romans, W. J. Niebuhr

With suitable instrumentation and techniques it is possible to determine the presence of tantalum in columbium to 20 ppm . This paper discusses the selection of X- ray spectrographic instrumentation and describes a technique for accomplishing the low level determination of tantalum . An ion- exchange method of separating tantalum from columbium is also described .

Jan 1, 1964

By A. E. Back

[Several processes for recovering manganese from low-grade ores have been proposed3/4/5/ in which an aqueous slurry of the ore is leached with gas containing nitrogen, oxygen, and sulfur dioxide as obtained from burning sulfur or roasting sulfide ores. The manganese dioxide is dissolved, and most of the sulfur dioxide is oxidized to sulfate, but an appreciable quantity of dithionate is usually formed, together with acid from oxidation of the sulfur dioxide. The over-all reactions may be represented as follows: (1) Mn02 + S02 = Mn++ + S04--. (2) Mn02 + 2S02 = Mn++ +S206--. (3) H20 + So2 + 1/2 02 = 2H+ 5S4--. (4) H20 + 2S02 + 1/2 02 = 2H+ + S206---.]

Jan 1, 1952

By R. L. Montgomery

Heats of solution of yttrium chloride and oxide in hydrochloric acid were measured by Bureau of Mines researchers. Using the heat of combustion of yttrium mentioned in the literature, the Bureau calculated the heat of formation of yttrium chloride to be -239.16 + 0.50 kcal./mole. The Bureau experiments gave evidence that the heats of solution of yttrium chloride from the literature are mostly too low because of water and/or oxychloride impurities. Heat of combustion of yttrium (8)3/ and its heat of solution in hydrochloric acid (2, 14) have been measured. The earlier heat of solution measurement (2) is unreliable because of possible potassium contamination (4). Heat of solution of yttrium chloride has been measured by three researchers (3, 9, 15), who obtained widely different results. Spedding and Flynn (14) report the heat of formation of yttrium chloride as -232.69 kcal./mole from their solution studies. The present work was designed to check the reported heats of solution of yttrium chloride and to determine the heat of solution of yttrium oxide. The latter measurement would allow the results of solution and combustion data for yttrium to be intercompared.

Jan 1, 1960

By Vladimir Nikolić, Alex Doll

The Bond ball mill grindability test is one of the most common metrics used in the mining industry for ore hardness measurements. The test is an important part of the Bond work index methodology for designing and measuring the efficiency of mineral grinding circuits. In spite of being called “Bond’s Law,” the work index equations are not a law of nature; but rather an empirically measured regression of a large data set collected by the Allis- Chalmers corporation in the period between 1930 and 1952. As a regression, it is valid within a specific “calibration space,” and great care is required when deviating the test procedures or observing results that are outside of that calibration space. This paper is a collected summary of other works by the Authors that describe feed sizes, product sizes, quality control checks, and other information about interpreting the test and using its results. Examples of adjustments that are sometimes required when using the test are: changing the test product (P80), and coping with a feed that is too fine to apply the “proper” feed preparation steps (such as is sometimes observed from HPGR or SAGDesign product testing). Related metrics, like the Morrell Mib value and Levin B value will be discussed, along with recommendations for their use on design projects. The intended audience is any user of laboratory work index test data.

Feb 1, 2024

By K. G. Lomberg

The density used to covert volume to tons is critical in determining the real in-situ tonnage of Mineral Resources. However, the methods used to determine density and the use of different technical terms are seen to be inconsistent throughout the industry. Probably the best discussion addressing the determination of density was presented by Lipton (2001). This paper does not try to replicate this excellent work, but rather to review current industry practice and present a comparison of the approach to density in public reporting. Some of the technical terms used in reporting and the common methods applied are also discussed.

Sep 1, 2021

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By Avinash Kandalam, Markus Reuter, Jörg Kleeberg, Michael Stelter

The Top Submerged Lance (TSL) technology has obtained significant importance in the pyrometallurgy industry for nearly four decades. One of the advantages of TSL furnace is its high reaction rate, which is caused by splashing and turbulence of the melt. In contradiction, this phenomenon stands as a barrier for conducting experimental investigations to validate the simulation models. The highly turbulent and splashing environment in the TSL furnace is caused due to the immersion of the lance into the slag layer and thus the effect of the flame structure is directly related to the splashing, turbulence, reaction kinetics and life-span of the lance. Moreover, the material properties such as viscosity, density and the surface tension will also influence the flame structure. As a first step to understand the flame structure, attempts are made to generate a stable flame of the lance in an open environment. INTRODUCTION Top Submerged Lance (TSL) technology was invented during the 1970s at Commonwealth Scientific and Industrial Research Organisation (CSIRO), Australia by Floyd and Denholm. This technology was later commercialised and currently, there are about 100 TSL plants around the world commissioned by various licence holders such as AUSMELT (Outotec) and ISASMELT (Xstrata- Glencore Technology). Copper is the most produced non-ferrous metal followed by lead and zinc, see Hunt (2005). Today, a wide range of primary, secondary, and complex recycling materials are used as a feed material in the TSL, Alvear et al. (2010), Kaye et al. (2008). The working principle of TSL technology lies on inserting and submerging a lance from the top of a vertical cylindrical chamber into the slag layer. The lance is considered as the heart of the furnace, where the air and fuel are transported through two concentric tubes and are mixed in a combustion chamber, which is approximately 7 cm from the tip of the lance (considering the pilot-scale TSL furnace at the Institute for Nonferrous Metallurgy and Purest Materials - INEMET). The TSL furnace is very flexible with the type of fuel, feed material and the air input. The fuel can be natural gas/heating oil/fine coal particles and the air could be enriched with oxygen (Figure 1). The general mechanism of the TSL furnace lies on feeding the material from the top of the furnace and the material is pulled into the molten bath due to the high turbulent atmosphere, which results in high reaction rates. The thermocouples installed in the furnace (i.e. in the ceramic linings) allow the operator to know the temperature of the melt. For example, in the case of copper production the tapped material (i.e. matte/metal) can be transported to a settler for further processing or directly used.

Jan 1, 2019

By Emmanuel N. Zevgolis

In the present work, a reduction roasting experimental study of Greek nickeliferous laterite samples with a gaseous reducing mixture ? CO:N2- is presented. The effect of parameters such as temperature, ore grain size, and composition of the reducing mixture were examined. It is deduced that the reducibility of intermediate type laterite sample, where iron appears mainly in the form of goethite (a-FeOOH), is considerably higher than that of limonitic type laterite samples, where hematite (a-Fe2O3) is the predominant iron mineral phase. The degree of reduction of the limonitic type laterite samples does not exceed 50%, while it reaches 95% in the case of the intermediate-type laterite sample under the same experimental conditions. Increasing the temperature in the range 750-900°C does not considerably favor the reduction of the limonitic type laterites, whereas decrease of ore grain size of the limonitic-type ore samples and more intense reducing conditions increase the reduction. The considerably higher specific surface area values of the intermediate laterite samples, diminishes the effect of the ore grain size and this can be regarded as the critical parameter leading to the higher reducibility of this ore.

Jan 1, 2009

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011

By M. Tanaji

Over the last many decades, a significant amount of research has gone into the domain of slurry transport. However, design engineers still face many challenges with respect to prediction of pressure drop, critical velocity and other design parameters as a function of Solids % and Particle Size Distribution (PSD). The industry requirement is to transfer the slurry at the maximum concentration as possible (above 30% (volume %)) to make slurry transport more economically viable and to reduce water consumption. To facilitate the design and scale-up of slurry transport in pipelines and in process plants, there is a need for a correlation that can predict slurry pressure drops over a wide range of operating conditions and physical properties of different slurries. The objective of this study is to overcome the limited range of applicability and validity of existing correlations and to develop a generalized but more rigorous correlation applicable to a wider range of slurry sys-tems. The existing Wasp et al. (1977) method is based on multi-phase flow modeling approach. This study attempts to modify this approach by considering material-specific values of Durand?s equation co-efficient and by defining flow regimes based on particle Reynolds number. When compared with experimental data, the modified Wasp method proposed in this study predicts the pressure drop for slurry flows more accurately than other available correlations. Also, the pro-posed method requires minimal test/experimental data for a particular slurry system and can be extended over different input conditions. An iterative computer algorithm is developed to calculate the criti-cal settling velocity and pressure drop in a pipe as a function of Solids % and PSD. The solution method can easily be implemented in de-signing slurry pipes, design validation, and studying the different slurry transport scenarios. The modified method can also be extended to accurately predict pressure drops in dynamic pressure flow networks used in commercial process simulators.

Feb 23, 2014

By G. C. Bateman

Canada is a very large country with a small population which is growing very slowly. We have great natural resources, but with our limited population we are continually looking afield for new capital to develop these resources. Our mining areas are among the most important fields offering opportunities for new capital and because of the wide-spread appeal which mining makes this industry commands a great deal of attention. While we are glad to see new capital from any source, we welcome it particularly from Great Britain, for, although we offer equal opportunities to the nationals of any country we would be glad to see the development of our natural resources financed as far as possible within the Empire. However, when we invite ne capital we must accept certain responsibilities, and while we have opportunities to offer, we should ask ourselves how these opportunities are taken advantage of and what sort of treatment the foreign investor receives.

Jan 1, 1925

By P. R. Jones

A computer program was written for the design of a shell and tube heat exchanger on a price optimum basis for the following conditions: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; (4) no change in phase; and (5) inside pumping costs immaterial. Price optimum design was obtained for four standard tube sizes and standard pitch. The inside pressure drop was fixed and outside pressure drop was computed for the optimum baffle spacing and when the baffle spacing equaled the shell diameter. Standard shells whose areas equaled or exceeded the required area were also listed. The program was made adaptable to various fluids and to various tube sizes and pitch by reading in many of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1968

By G. N. A. Senhorinho, J. A. Scott, C. A. Laamanen

"Closed mine sites are widely regarded as a negative asset due to their legacy of environmental impacts. These sites are often characterized by waterbodies with elevated metal concentrations and low pH that are traditionally considered to have little or no value. These sites are potential sources of beneficial biocompounds produced by microalgae in response to environmental stresses. A bio¬prospecting program found that certain microalgae from waterbodies near historical mine sites exhibited higher antibacterial activity than any microalgae previously reported in the literature. There is potential for the mining industry to be involved in examining features such as tailings ponds at mine sites for high-value compounds, including ones that might help mitigate rapidly growing microbial resistance to current antibiotics. ¦ KEYWORDS Antibacterial, Closed mining sites, Metabolites, Microalgae, Stressed environments RÉSUMÉ Les sites miniers clôturés sont généralement considérés comme des actifs négatifs en raison de leurs répercussions sur l’environnement. On trouve souvent sur ces sites des étendues d’eau affichant de fortes concentrations en métaux et un pH faible, généralement considérées comme ayant peu, voire pas de valeur. Ces sites sont des sources potentielles de biocomposants bénéfiques produits par des microalgues en réponse aux perturbations environnementales. Un programme de bioprospection a permis de déterminer que certaines microalgues trouvées dans ces étendues d’eau à proximité de sites miniers historiques présentaient une activité antibactérienne supérieure à celle mentionnée dans toute la docu¬mentation existante. L’industrie minière pourrait bien participer à l’examen de particularités telles que la recherche de composants à haute valeur dans des bassins de décantation des résidus sur des sites miniers, notamment des composants qui pourraient aider à atténuer l’augmentation rapide de la résistance micro¬bienne aux antibiotiques actuels. ¦ MOTS CLÉS antibactérien, environnements perturbés, métabolites, microalgues, sites miniers clôturésINTRODUCTION The mining industry is one of the largest economic drivers in the world. Within Canada, for example, it contributed 2.8% (C$57.6 billion) of the 2016 gross domestic product (Marshall, 2016). Canada also has the highest non-ferrous exploration budget worldwide (Marshall, 2016); therefore, it is likely that mining operations, mine waste disposal, and the number of closed sites will continue to grow in Canada. The environmental impact of mining operations stems from the volume of tailings produced, which can be up to 97–99% of the total volume of ore processed at a mine (Adiansyah, Rosano, Vink, & Keir, 2015). In 2010, mining was the world’s largest industrial producer of waste at a total of 65 billion tonnes: 51 billion tonnes of waste rock (mine overburden) and 14 billion tonnes of tail¬ings (Jones & Boger, 2012)."

Jan 1, 2019

By J. G. Thomson

Development of the Canadian North, a subject of growing national interest, must in part await the development of better forms of trans-port. The estimated 500,000 square miles of muskeg terrain in the north combined with the" scarcity of roads make essential the early development of special purpose muskeg vehicles. Good progress has been made in the last eleven years in classifying muskeg and some progress has been made in determining its mechanical properties. Limited travel is now possible through the use of special purpose tracked vehicles which have been built without adequate design data. A program to provide data which can be used to optimize muskeg vehicle designs began in 1957. The results of the second phase of this pro-gram are presented in this report. It is shown that vehicle performance in muskeg is directly related to the mechanical properties of the muskeg. Further, it is shown that good de-sign practice for tracked vehicles expected to operate in snow, sand, soft clays and loams is also good practice for muskeg vehicles. All indications are that muskeg mechanics is properly a part of conventional soil mechanics.

Jan 1, 1961

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

By John Hardy

The performance of five dense-medium washers was evaluated in four preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation. The secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The sharpness-of-separation was excellent for all four primary separations and the secondary separation.

Jan 1, 1966