Search Documents

By S. Harshaw, C. Doyle, A. E. M. Warner, D. Stremlaw

"In the Utility Nickel furnaces, the hearth and sidewalls are lined with high-Al2O3 bricks. During charging and thermal cycling (more so as the linings on these reverberatory furnaces age), pieces of brick spall or abrade from the refractory and collect on the top of the bath. These pieces are removed using a non-corrosive slag toward the end of the heat when the bath temperature is ~1600°C.This benign liquid can be generated by two methods. First and most obvious, suitable ingredients can be pre-mixed so that the flux (flux A) is isochemical with the non-corrosive slag. All that is needed to produce this targetted slag is heat. Second, in other proportions (flux B), the pre-mixed ingredients generate a corrosive slag that melts completely at -1200 °C and corrodes some but not all of the brick particles on the bath surface. As the reaction progresses, the slag changes composition eventually attaining the targetted benign composition. Using this option, additions are monitored to avoid overfluxing. In both cases, the generated slag/brick mixture can then be rabbled from the furnace. This practice has been successfully used for over two years and has been a factor in extending Utility Nickel furnace life to its current levels (about25% increase)."

Jan 1, 1993

By Grace N. Broderick

U.S. supply and demand data for coal, by States and regions, were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the coal industry that can be integrated into State and regional energy balances by source, form, and consumer sectors, and used for estimates of interstate and interregional energy flows. The tables give an estimated total supply of coal available for consumption, and also report the distribution of the supply among the major consuming sectors (household and, commercial, industrial, transportation, and electricity generation). To enable comparison of coal data with those for other energy forms, tonnages were converted to British thermal units (Btu). Future energy analysis studies could be facilitated by changes in the categorization of information collected on the coal industry. The data shown are based primarily on Bureau of Mines source material.

Jan 1, 1969

By E. E. Donath, L. L. Hirst, L. C. Skinner

Two processes are available for the production of synthetic fuels from coal high-pressure hydrogenation and the carbon monoxide-hydrogen synthe- sis. This paper presents some ideas and new developments in coal hydrogen- ation that have been incorporated in an estimate for the production of 30,000 barrels per day of liquid fuels, mainly gasoline. A few comparisons of the processes will be helpful before discussion of the details of pro- posed improvements in the hydrogenation process. The principle of the high-pressure hydrogenation process ie the addi- tion of hydrogen at pressurea in the range of 3,000 to 10,000 p.s.i. to coal at elevated temperature and with the help of catalysts. On the other hand, the principle in the Fischer-Tropsch synthesis is the complete break-down of coal into a mixture of carbon monoxide and hydrogen, followed by the catalytic combination of these two gasse into hydrocarbons or suitable catalysts. For the synthesis, moderately elevated pressures of about 350 p.8.1. will bo used in the immediate future, although it can be carried on at atmosphoric pressure with certain catalysts. The products of these two processes using coal as raw material are almost as differont as hydrocarbons can be. The products of the high-pres- sure hydrogenation of coal reflect the original constitution of the coal. They are, therefore, rich in ring compounds, both aromatic and naphthenic, but, due to the action of highly comprcesed hydrogen and catalyst, are satu- rated and very stable. These constituents give the gasoline a high octane number and excellent rich-mixture performance, combined with good gum and storage stability. Therefore, this gasoline is suitable for aviation gaso- line or base stock. The Diesel fuel can be hydrogenated to a centane number of 45 or higher, which is entirely satisfactory for operating normal Diesel

Dec 1, 1948

By Nestor Chavez, Javier Aymachoque, Carlos Ortega, Pedro Vasquez

Mientras que en la minería a tajo abierto es usual realizar planificación estratégica, en las operaciones subterráneas, debido a la complejidad de cada yacimiento, no existe un sistema normalizado para evaluar y optimizar la forma del área de la mina y su producción para obtener el valor real más alto. El objetivo del presente trabajo técnico es mostrar un sistema robusto capaz de optimizar y programar los depósitos subterráneos. Para ello, se evalúan múltiples escenarios de planes mineros en 3D en un plan minero de mina subterránea, analizando en poco tiempo diferentes variables, mostrando la robustez del planeamiento y analizando la incertidumbre asociada a las variables más relevantes. Se presenta un flujo de trabajo completo y práctico que ha mejorado los valores y reducido los riesgos de un proyecto subterráneo.

Sep 20, 2019

By L. C. IlsLey, H. B. Freeman

In connection with the approval of coal-cutting machines for service in gaseous mines , the engineers of the Bureau of Mines have been somewhat concerned as to the type of trailing cables that could safely be used on permissible outfits . While no final action has been taken on this question ( tentative approvals having been granted pending investigations ) , the Bureau has been endeavoring to collect data and information on this question which would permit a fair , yet safe , ruling to be made . For this purpose cooperative arrangements were made with three coal companies to visit certain of their mines , making inspections inside the mines to observe the cables and cutting machines in operation . In all , twenty mines were visited . A questionnaire covering the operations of trailing cables was filled out at each of these mines . In a few instances no personal inspection was made , the information being supplied by mine officials after conferences with the Bureau's engineer . At other mines the information given by mine officials was supplemented by personal observation inside the mines , usually at a time when the cutting machines were in operation .

Jul 1, 1923

By Henry M. Harris

Low-carbon shales from 65 deposits and 11 sources of coal-mine waste in western Oregon and Washington were tested in a rotary kiln for their suitability as raw material for expanded aggregate. Shales from 41 sources bloated enough to produce crushed, expanded aggregates, weighing less than 65 pounds per cubic foot in the preliminary tests. The samples were judged on the basis of processing qualities, physical properties, and size and uniformity of the source. Nine low-carbon shale deposits and three coal-mine waste sources were selected for more extensive bloating tests and for examination of the expanded aggregates in concrete shapes. Composite samples from these 12 sources and from 2 commercial operations, when processed for testing in concrete shapes, had bulk densities ranging from 37.S to 72.9 pounds per cubic foot. Damp-cured concrete shapes made with these aggregates had bulk densities ranging from S6 to 119 pounds per cubic foot, and all but three of the lightweight concretes had crushing strengths ranging from 3,270 to 6,810 p.s.i. Properties of the lightweight concretes were compared with those of concrete shapes made with commercial aggregates, and with sand and gravel.

Jan 1, 1962

By Jacob T. Wainwright

AS a means for increasing the efficiency in modern blast-furnaces by supplying to them blast of a much higher temperature than is now possible, the writer offers as a suggestion a modification in the construction of regenerative hot-blast stoves. Stated briefly, the plan proposed is to pre-heat both the gas and the air for its combustion in a manner similar to that generally adopted in Siemens openhearth furnaces. After thus carrying the temperature of the stove to a point much higher than that common in hot-hlast stoves, the cold blast passes through it. Without entering into the details relating to the reversing valves and the system of flues, the general plan may be outlined as follows, referring to the accompanying drawings: The valves are so placed in heating up the stove that the blast-furnace gas enters at B, Fig. 1, and the cold air for combustion at A. Ascending in flues, F and E, respectively, combustible gas and air meet and mix in the combustion-chamber, I. Flowing through K, they descend through the flues, G and H, escaping through the chimney. In this manner the walls of the combustion. chambers, I and L, are highly heated, and the right-hand side of the stove is carried to a higher temperature. By reversing the valves, blast-furnace gas enters at C and cold air for combustion at D. Both are pre-heated in their ascent through the flues, G and H. They burn in the combustion-chamber, L, and the hot gases of combustion, flowing through K, I, E and F to A and B, heat the left-hand side of the stove. In this manner the stove is carried to a temperature greater than that of those now generally in use, in which air and gas are burned without preliminary pre-heating. In the plan proposed, that side of the stove will, of course, be relatively cooler through which cold air and furnace-gas last passed in its ascent to its combustion-chamber. After having sufficiently heated the stove in the manner outlined, the cold blast is admitted through all the flues, A, B, C and D. It ascends through the highly-heated regenerative material to the chambers at the top and descends through the flue, P, Fig. 2 (dotted

Jan 1, 1889

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022

By E. O. Wagner, Manuel Gomez, W. S. Landers

The Bureau of Mines studied coking rates of a special Columbia - Geneva six - coal blend to establish the effect of the coking rate on coke properties . The tests were conducted in a 500 - lb , 14 - in experimental slot oven at essentially constant conditions of blend composition , size distribution , surface moisture content , and bulk density . The coking rate was varied as a function of oven flue temperature . Coking rates within the range of 0.56 to 1.35 in/hr were achieved . Increase in the coking rate decreased the size of the coke . The stability factor of the coke showed no significant change with coking rate until coking rates greater than 1.0 in/hr were reached , after which a decrease in the stability factor was observed . The apparent specific gravity increased to a maximum value at coking rates approaching 1.1 in/hr and decreased sharply with further increase in the coking rate . Coke parameters correlated well with the coking rate .

Jan 1, 1963

By Robert D. Pehlke

"The evolution of oxygen steelmaking is reviewed and new operating processes are described. The developments which could impact this technology are summarized. Staged and continuous steelmaking are considered in the light of new technologies. The future opportunities for oxygen steelmaking processes are overviewed. IntroductionThe use of oxygen in steelmaking was originally brought on the scene by the development of pneumatic steelmaking. Sir Henry Bessemer in England originally conceptualized the use of gaseous oxygen in steelmaking, and then he and William Kelly in Eddyville, Kentucky independently developed the original pneumatic process which involved blowing air through a bath of molten pig iron to oxidize the carbon and silicon and produce steel. This process and many following processes, including those which would use pure oxygen gas, have been proposed.Beginning with the first commercial oxygen steelmaking vessels at Linz, Austria in 1952, the world steelmaking industry has adopted this style of processing. In general, the process has involved the use of steel scrap in amounts from 20 to 35% of the metallic charge with molten pig iron produced in blast furnaces making up the remainder. The impurities in the charge are oxidized through the use of oxygen gas injected into the steelmaking vessel.However, currently being adopted into commerical practice and on the horizon are a number of advances in this process which include the use of iron ores as a source of iron and oxygen, the use of an all scrap charge, incorporation of pre-reduced iron, the use of auxillary fuels to change the balance of cold and liquid iron-base charge materials and numerous refining techniques."

Jan 1, 1988

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961

By Van E. Shaw

Three comparatively simple, efficient, and rapid extraction methods for the dissolution of yttrium and rare-earth elements from a euxenite carbonate residue have been developed, using dilute sulfuric acid as the solvent. Extraction processes have resulted in yields of 98+ percent of the total rare-earth elements and yttrium contained in the residue and have given preliminary separation between the cerium-group and the yttrium-group rare-earth elements. Extraction procedures presented are: Procedure 1. -The recovery of total rare-earth elements and yttrium by a cold dilute sulfuric acid leach at a pH of 2.5. Procedure 2. -The recovery of yttrium and yttrium-group rare-earth elements by leaching with dilute sulfuric acid at 125° F. and a pH of 3.0, with subsequent recovery of the cerium-group rare-earth elements by a cold dilute sulfuric acid leach of the residue at a pH of 2.5. Procedure 3. -The recovery of the total rare-earth elements and yttrium by fractional leaching as in procedure 1, followed by boiling the sulfate solution, which precipitates the cerium-group rare-earth elements and leaves the yttrium-group rare-earth elements in solution.

Jan 1, 1959

By Wilson Pascheto

One of the main outcomes of a capital project is the reliability of a new plant, system or equipment. During 20 years of experience working in various capital projects for the mining industry, the author experienced failures which have caused significant losses to Owners, in many cases amounting to millions of dollars and almost jeopardizing entire projects. Often, failures were related to faulty design, shop fabrication and/or construction. Therefore, significant opportunities exist in the Mining Industry to improve the success rate of capital projects, improve on-line time at start-up, minimize the occurrence of unplanned maintenance due to equipment failures, and all this with positive contribution to health and safety. This paper presents some examples of failures and how they could have been prevented by proper Quality Assurance methodology. It also discusses some of the main challenges in the implementation of such methodology, including awareness of the Materials discipline and availability of trained Engineers.

Jan 1, 2015

By David K. Hylbert

This study investigated stratigraphic and structural causes of roof falls in room-and-pillar drift coal mines in nine mines in eastern Kentucky. A contract modification provided for remote sensing studies in the Dunkard Basin of West Virginia and Pennsylvania. Results of stratigraphic and structural studies of an earlier contract (H0133018) were applied to several new mines. It was found that similar rock sequences contributed to unstable roof conditions. Structure contour and isopach maps were found useful In projecting these trends together with fence diagrams. Using Landsat imagery, a direct relationship was found between lineament direction and the trends of rock jointing, roof fall zones, "snap top" zones and sandstone channels in the examples cited. It was found that, by analyzing lineament intersections, from 50 percent to 65 percent coincided with roof falls.

Jan 1, 1980

By W. de Bruijn

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically pre-pared hematite powder evenly doped with 1% by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous thermo-gravimetric and dilatometric analyses were per-formed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process.

Jan 1, 1988

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling.INTRODUCTIONThe early 1900?s saw the beginnings of published papers which tackled the problem of what influenced the power draw of tumbling mills and what equations (models) were suitable for predicting power draw. This interest continued for the rest of the 20th century and the literature contains many papers that attempted to satisfactorily answer these questions. A common and disappointing theme in the majority of them, however, is the distinct lack of suitable experimentally derived power draw data. This deficiency consequently limited the practical application of many of the attempts at modelling mill power draw. Prior to the early 1990?s some limited data on the power draw of grinding mills in the literature can be found, but as Harris et al (1985) remarked they are ?... too frequently unusable simply because one or more essential variables have been omitted?. The absence of published results, from vigorous experimental testing of the various models, has resulted in a general lack of evaluation of the validity of assumptions and hypotheses that such models contain. Harris et al (1985) however, did make some efforts in attempting to evaluate the performance of various power prediction equations and in so doing further developed a semi-empirical one of their own. However, in using manufacturers? published data, which themselves were undoubtedly generated by proprietary equations of unproven validity, they probably succeeded in generating little more than a consensus of the various errors in these models."

Jan 1, 2003

By V. C. Rogers

ALTHOUGH surveying at mining properties is fundamentally the same regardless of the method of mining, at Climax, due to the nature of the ground, the policy of advance development work, and extremes in climatic conditions, surveying practice has had to be revised to meet the specialized conditions of this particular type of mining operation. The company's mine is one of the largest underground properties in the United States. It has proved ore reserves of 275,000,000 tons, 60,000,000 tons of which have been broken. To date, 109,000 ft. of development drifting have been driven, as well as 40,926 ft. of development raising, 10,000 ft. of ventilation drifting and raising, 16,000 ft. of exploration drifting, and 206,000 ft. of diamond drilling. Normal production varies between 1.2,000 and 15,000 tons daily. Development work proceeds at a rate of 11/2 tons developed for every ton milled and with a development of 18,000 to 20,000 tons per day, the following crew is required to take care of mine and surface engineering

Jan 1, 1946

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010