Search Documents

By J. L. Konchesky

The technical feasibility of gasifying powdered, noncoking, low-rank coal with steam in an externally heated tube has been demonstrated. The tube, 112 ft. of alloy-steel tubing shaped into a helix, served as an electrical conductor of electricity used for heating. The effects of the following variables were studied: Residence time of coal in reactor, average reaction temperature, steam concentration, and rank or geologic age of coal. Reaction pressure was maintained in the range 19-26 p.s.i.a. High carbon conversions and large yields of synthesis gas were obtained with low-rank coal. In one test, for example, about 88 pct. of the carbon in a subbituminous C coal was gasified at 1,910* F. with a residence time of 1 sec. The gas contained 58 pct. H2, 19 COD 15 CO, and 3 CH4; the yield was 30 cu. ft. (at 32' F. and 14.7 p.s.i.) of synthesis gas (CO + H2) per pound of dry coal.

Jan 1, 1960

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J. Ouellet

"ABSTRACTA brief background on in-situ testing of mine backfill, as well as pressuremeter testing is briefly described, and results from an in-situ testing on paste backfill are presented. A series of self-boring pressuremeter tests were done from the top of a backfilled stope in an underground mine. The tests were conducted along a 20-metre vertical line in the centre of the stope. Some 14 tests were performed along this depth. The instrument used was a Camkometer built by Cam Insitu, Cambridge. The instrument proved to be efficient and reliable for underground testing in a cemented paste backfill. The testing program was conducted within the planned schedule with a high success rate. The test done in this study permitted the measurement of paste backfill strength, stiffness and in-situ horizontal stress within the backfill. RésuméUn bref historique des essais in situ dans le remblai minier est présenté. L’essai pressiométrique est décrit succinctement et des résultats d’une campagne d’essai dans un remblai en pâte sont présentés. Un programme d’essais au pressiomètre auto-foreur a été réalisé à partir du sommet d’un chantier remblayé sous terre. Les essais ont été réalisés le long d’un ligne vertical d’environ 20 mètres pour un total de 14 mesures. Le Camkometer de la firme Cam Insitu de Cambridge a été utilisé. Cet instrument s’est avéré efficace et fiable pour tester le remblai en pâte cimenté sous terre. Le programme d’essai s’est déroulé à l’intérieur de l’échéancier prévu avec un taux de réussite élevé. Ces essais ont permis de déterminer la résistance, la rigidité de ce remblai ainsi que les pressions in-situ prévalant dans le remblai."

Jan 1, 2000

By AIME AIME

WIDESPREAD interest in the better utilization of coal is indicated by the attendance of over seventeen hundred men interested in the pro- cessing and utilization of coal and its by-products, at Pittsburgh, Nov. 15 to 18. The conference was truly international in scope and of a scientific character, and must be considered a real success. There were dele- gates--official and unofficial-from America, Belgium, Canada, Czechoslovakia, France, Germany, Great Britain, Japan, Mexico, and Sweden. Several Federal and 28 State departments had representatives, also many colleges and universities, and many leading industrial and mining corporations throughout the country. A feature of the sessions was that papers were mostly read in full and attentively listened to, although in some cases they were of a technical nature. The proceedings were opened by the president of Carnegie Institute of Technology, Thomas C. Baker, who spoke of the importance of the conference and felt that without foreign cooperation it could not have been held. There was no need to apologize for the movement of Carnegie Institute of Technology in the matter. Coal is commanding attention in every part of the world; so is power; and coal will remain the chief source of power for generations to come. The coal chemist is working with the engineer, and nobody can forecast what developments there will be in fuel technology. This conference may be the turning point of fuel technology in America. The development and application of these new processes may be of great benefit to Pittsburgh.

Jan 1, 1926

By Tapan Goswami

The expectation from the blasting engineers and shotfirers is often that explosives will perform optimally at all times. However, in reality, non-ideal situations exist on mine sites and occurrences of poor explosives performance are common. Often the cause is difficult to identify. Having a good application technique and analysis skills will minimise the risk of poor performance. This paper will discuss the experiences gained by the author while blasting in the Hunter Valley, Australia.

Jan 1, 2003

By Débora Ribeiro Lopes

A descoberta das grandes reservas de petróleo e gás ao longo da costa sudeste do Brasil representou um novo desafio tecnológico na história da indústria brasileira de petróleo. Entre as principais dificuldades pode-se citar: água ultra profunda, espesso leito de sal, alta pressão, baixa temperatura, ambiente muito corrosivo contendo contaminantes como o gás carbônico (CO2) e o sulfeto de hidrogênio (H2S). O objetivo deste trabalho é o estudo do comportamento eletroquímico de um aço inoxidável supermartensítico contendo cerca de 14% de cromo (Cr), em meio contendo 115.000 ppm de íons cloreto, 10 ppb de oxigênio dissolvido, com adição de 10-2 mol/L e 10-3 mol/L de tiossulfato de sódio. Para tal foram empregadas as técnicas de polarização anódica potenciodinâmica cíclica e microscopia ótica. Os resultados experimentais mostraram que ocorreu uma variação significativa na extensão da região de passivação quando tiossulfato de sódio foi adicionado ao meio, aumentando a susceptibilidade à corrosão por pites do material.

Jan 16, 2018

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By J. Pang

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and AC impedance spectroscopy techniques. Analysis of the impedance spectra using equivalent circuit models has made it possible to suggest layerwise growth of surface films. From the value of equivalent circuit parameters, properties of the surface layers are inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution and give rise to changes In contact angle and flotation response. In agreement with prior investigations, the present study shows that flotation recoveries alone cannot be used to determine the effect of collector on flotation of chalcopyrite. The rate of flotation is a more sensitive parameter to determine the role of collector on floatability of chalcopyrite.

Jan 1, 1989

By Matthew A. Perras

With growing populations, infrastructure projects are utilizing underground space to expand transportation networks, water supply and sewer disposal systems and hydropower facilities. These new projects require large diameter tunnels to meet the growing demands. As the tunnel diameter increases, not all rock mass properties are scalable and precedent experience becomes less reliable. One such non-scaleable property is lamination thickness. Numerical modelling was conducted to determine the influence of lamination thicknesses on a 16 m diameter tunnel. Five different areas of excavation response were found to exist for laminations ranging between 0.16 to 16 metres in thickness. For this tunnel diameter, critical lamination thicknesses of 6 metre and 1 metre were found to exist. Above 6 metres the excavation response was similar to isotropic models. Below 6 metres the stresses and yield are channeled by the lamination boundaries, increasing plastic deformation. Below 1m multiple lamination units become unstable and the displacements increase significantly and the shape and extent of the yield zone size changes dramatically. The yield zone is controlled by bed deflections and bed parallel shear. As the lamination thickness decreases tensile failure first begins in the haunch area and progressively extends above the crown until a self-limiting plastic yield zone shape is reach at lamination thicknesses below 0.4 metres. Conclusions drawn from observations at the Niagara Tunnel Project are those of the authors.

May 1, 2009

By T Takayama, R Muroi, M Matsumura

The steel industry occupies 14 per cent of CO2 emissions in Japan, and the sintering process is one of the major emitters. Since most of CO2 released from the sintering process comes from coke fine combustion, replacement of coke fines with biomass char as bonding agent is a potential countermeasure. In order to explore the effective use of biomass char, we chose char made from Palm Kernel Shell (PKS) as a sample. First, the char’s combustion behaviour was examined with varying the char’s particle size by means of admixing the char in alumina ball packed bed placed in an electric furnace. As a result, the finer the PKS char the faster the burning rate and reaching a higher temperature compared to coke fine. In addition, it is also concluded that the optimum size of PKS char was larger than coke fines. Next, the effect of different heat profiles on sinter structure was examined by sintering tablet made of chemical reagents. In this experiment, the chemical composition is designed based on sinter composition. By this sintering test, even at high temperature, rapid cooling is effective to make fine sinter matrix and fine pores, which has possibility for high sinter reducibility. Based on these two experiments, using PKS char as a sinter fine source has the possibility to improve sinter reducibility.

Nov 8, 2021

By Haibin Wang, Baojun Zhao, Xueyi Guo, Zhixiang Cui, Zhi Wang

In conventional copper production, anode copper is produced from concentrate in three furnaces in a process that entails four oxidation steps and one reduction step. Three types of slags are produced that require further treatment to recover copper. Dongying Fangyuan Nonferrous Metals recently developed a simplified process which requires only two custom-designed furnaces instead of the conventional smelting, converting and re fining furnaces. The first furnace continuously produces high-grade matte (>75 wt% Cu) that contains little iron (<2 wt% Fe). The liquid matte is continuously fed to the second furnace, which produces anode copper. The new process signi ficantly reduces the capital and operating costs and increases productivity and environmental sustainability. This paper presents fundamental concepts that enable the simpli fied process to be developed. The detailed operations in Dongying Fangyuan Nonferrous Metals are also described.

Mar 1, 2018

By N. Hoffman

Accurate, repeatable density measurements of a coal-magnetite-water slurry are difficult to achieve using a nuclear density gauge. Changes in the coal-to-magnetite solids ratio cause fluctuations in the readings of nuclear gauges. To investigate this problem the Electric Power Research Institute&apos;s Coal Cleaning Test Facility compared the performance of a nuclear density gauge on a coal-magnetite-water slurry with the performance of a differential pressure gauge modified with a new pressure sensor. A second aim of these preliminary tests was to determine if the differential pressure gauge is also sensitive to the type of solids in the slurry. This paper explains current slurry density measurement practices, describes the nuclear and differential pressure gauges used in the CCTF tests, and presents test methods and results.

Jan 1, 1986

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez, Nishan Pokhrel, Lizeth Jaramillo

This paper presents a case study of respirable dust characterization in a thin-seam coal mine in southern West Virginia. Samples were collected in various locations within the mine and analyzed using scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), thermogravimetric analysis (TGA), and Fourier transform-infrared (FT-IR) spectroscopy. The study found high non-carbonate mineral content, particularly aluminosilicates and silica, in the dust. The results indicate that fine aluminosilicate particles may interfere with SEM-EDX analysis, leading to an underestimation of coal content. The findings highlight the importance of using multiple analytical methods to accurately characterize respirable coal mine dust.

May 5, 2022

By Tuula Mäkinen, Lauri Pesonen, Peter Björklund, Jouni Pihlasalo, Mikko Korpi

Outotec Direct Blister Flash Smelting technology has proved to be an efficient and environmentally friendly way to treat copper concentrates from the Zambian Copperbelt at Konkola Copper Mines&apos; (KCM) Nchanga smelter in Zambia. The modeling of slag chemistry and thermodynamics with MTDATA software played a central role in deciding the operation parameters for the smelter. Outotec FSF Online Process Advisor is used to calculate the process parameters and to give valuable information of the process state for the operating personnel. The pre-calculated slag liquidus graphs are also integrated to the Online Advisor.

Jan 1, 2011

By A. D. Fisher

This paper describes the future position of metallurgical coal, particularly as applied to Canadian reserves. Quality coking coal is declining in availability, but preheating practices may alleviate this situation to some extent. Two new processes are discussed in the paper - formed coke and direct reduction - and their coal specifications are outlined.

Jan 1, 1972

At its Copper Cliff Smelter, Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. The furnace matte is converted to low iron matte for further processing, and the molten converter slag is recycled to the flash furnaces. The flash furnace slag is discarded. Natural gas or coke supplies a minor proportion of the process heat requirements, thus limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Preliminary experiments were conducted in a mini plant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. This paper presents the experimental results and discusses key aspects of the possible operation of the Inco flash furnace with a coke barrier separating the freeboard from the molten bath.

Jan 1, 2003

By Jack F. McQuat, Ross D. Lawrence

"Most geologists and mining engineers, in the course of their professional careers, frequently become involved with the appraisal of metalliferous mineral deposits and develop a familiarity with and standard approach to the evaluation of these deposits. When the same individuals approach the industrial mineral field, however, their usual approach pattern can be rudely disturbed.This paper highlights the difference in appraisal approach and outlines the factors common to both but which have entirely different emphasis. These comprise geological appraisal, analytical requirements, the importance of transportation, marketing requirements and standards, including appropriate allowances for product development, and marketing penetration.Out of these ""different"" considerations, however, a pat-tern or standard approach emerges which is as common to the industrial mineral field as that used either consciously or subconsciously in the metallic field.The paper reviews the different factors and points of emphasis and offers an outline of the common pattern of appraisal for industrial minerals."

Jan 1, 1971

By Staff

Introduction As the Sherritt Gordon property is still in the development stage, . it is rather difficult to write a proper account of the mining methods and milling practice that will be used. While the general scheme of operation will remain the same, there will undoubtedly be many minor changes to meet special conditions which we cannot forsee at the present time. Most of the work accomplished to date has followed the usual routine of preliminary development in the Canadian North. However, we have learned a few things which might be of use to others operating under similar conditions. The most important of these is the saving in power cost made possible by the use of Diesels as against steam power when using wood fuel, and the movement of freight by tractors when rail transportation is not available. Location The property i6 located about 90 miles north of The Pas, or 40 miles northeast of the Flin Flon mine. A branch line from Cranberry Portage, on the?C. N. railway, between Flin Flon and The Pas, connects the property with the outside.

Jan 1, 1930

By E. Miller, K. L. Komarek, M. Ettenberg

The activity of aluminum in solid Co-A1 alloys has been measured by an isopiestic technique between 850° and 1200°C from 45 to 80 at. pct Al. The activity shows a Precipitous decrease around the stoichzornetric composition of CoAl. Free energies of mixing have been calculated over a limited composition range. Considering an antistructure-vacancy defect mechanism, the degree of intrinsic disorder, a , in CoAl was related to the alunminum activity. Excellent agreement between the calculated and experimental activity curves was obtained for a = 1.25 x 10-4. ThERMODYNAMIC properties of solid aluminum-transition metal alloy are being studied in an investigation of disordering in ordered compounds. In a continuing series of investigations, activities of solid Fe-1,&apos; Ni-A1, kd r-A13 alloys have been measured. From the results for Fe-A1 and Ni-A1, the degree of intrinsic disorder for the equiatomic compounds was calculated2 using equations derived by Wagner and chottk. From the results for Cr-A1 the degree of intrinsic disorder was calculated from equations derived by Orr.&apos; In this paper, the results of the study of Co-A1 alloys are described. Published activity data in the Co-A1 system has been limited to liquid alloys at 1600°C.° A heat capacity study7 of stoichiometric CoAl indicated that a second-order phase transformation occurs at 790° C, attributed to an order-disorder reaction. Oelsen and Middel,&apos; employing the calorimetric mixing of pure liquid metals, obtained heats of formation for compositions from 6 to 90 at. pct Co. Heats of formation for 50 and 78 at. pct Co alloys have also been measured by acid solution calrimetr. The Co-A1 phase diagram, as compiled by Hansen and Anderko,lo is in good agreement with more recent X-ray evidence. The method for measuring activities of aluminum in this study is essentially that employed in the studies of the Fe-1,&apos; i-Al, and r-A13 systems. This isopiestic method entails placing cobalt specimens, in a temperature gradient, in a sealed alumina system containing a pure liquid aluminum source of fixed vapor pressure. The specimens are equilibrated, cooled to room temperature, and their final compositions determined. From the measured temperature of the specimens and the known vapor pressure of pure aluminum the activities of aluminum in the alloy can be calculated. EXPERIMENTAL PROCEDURE The cobalt was 3-mil-thick sheet of 99.9 pct purity (herritt Gordon Mines Ltd., anada). The major impurities were 0.1 pct Ni, 0.014 pct C, 0.018 pct Fe, 0.004 pct S, and 0.005 pct Cu. The aluminum metal had a purity of 99.99 pct (Aluminum Corp. of America) and all alumina parts were 99.7 pct A1,O3 (Triangle RR Grade, Morganite Refractories, Inc.) with major impurities 0.05 pct SiOz, 0.1 pct Fe203, 0.2 pct NazO, and 0.05 pCt K20. Runs 1 to 3 were made with annular cobalt specimens (12 mm ID by 21 mm OD) punched from the sheet. The specimens were deburred and degreased in carbon tetrachloride and in acetone. The samples, each weighing about 150 mg, were then positioned along an alumina rod, a in. OD by 14 in. long, separated by alumina spacers, i in. ID by | in. OD by & in. long. The lower end of the rod was placed in a hole drilled in the center of an 80-g aluminum cylinder. This assembly was put into an alumina crucible, 1+ in. ID by 13 in. OD by 3+ in. high, and the position of each sample was measured to within 50.5 mm relative to the bottom of the crucible. An alumina tube, 28.5 mm ID by 35.5 mm OD by 14 in. long, closed at the top, was slipped over the whole assembly, so that it fitted snugly into the bottom crucible. The entire reaction assembly was tied with molybdenum wire and lowered into a mullite tube, closed at the bottom. A quartz thermocouple tube, closed at one end, containing a t/Pt-10 pct Rh thermocouple, calibrated according to the specifications of the National Bureau of standards,&apos;&apos; was placed along the reaction assembly inside the mullite tube. The temperature of each specimen could be determined by gradually raising the thermocouple and measuring the temperature gradient along the reaction assembly. The combined error in temperature measurement and sample position resulted in a total error of Q°C in the recorded temperature of each sample. The mullite tube was sealed at the top by a water-cooled brass head, connected to a conventional glass vacuum system. The aluminum reservoir is heated to its melting point sealing the alumina system containing the samples. During this process the pressure is maintained below 0.01 li Hg. During subsequent heating to establish the proper temperature gradient and throughout the entire run the pressure is maintained below 2 1 Hg by means of a two-stage mechanical pump. Equilibration runs lasted from 4 to 6 weeks and were terminated by air cooling. The temperature of the liquid aluminum reservoir was brought below its melting point in less than 20 min. For runs 4 and 5, alloy buttons with 49 and 69 at. pct A1 were prepared from the initial high-purity metals by arc melting under purified argon. The alloy buttons were comminuted to powder with an alumina mortar and pestle until the powder passed through a 400-mesh screen, particle size 0.0014 in. Portions of this powder weighing between 50 and 200 mg were placed in small alumina trays, 25 by 15 by 5 mm, which were then

Jan 1, 1969