Search Documents

By A. W. Deurbrouck

Four samples of Pittsburgh-bed coal, of various size consist and ash content were dewatered in a pilot-size vacuum-disk filter partially enclosed with a steam jacket. Steam fed at 2.5 to 12.5 pounds per minute reduced the moisture content of the filter cakes from 2.8 to 13.8 percentage points more than normal vacuum dewatering. Approximately 1.5 pounds of steam was required to remove 1 pound of water.

Jan 1, 1966

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago, there were only a small number of projects that stretched beyond 100 kt/d (110,000 stpd) throughput rates. Today, and moving forward, virtually all the major copper projects are sized beyond this, with throughput rates up to 250 kt/d (275,000 stpd) now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 (5,650 cu ft) flotation cells, through to the 257 m3 (9,076 cu ft) cells and to the current 660 m3 (23,380 cu ft) machines. The contributions of specific copper concentrators to this growth phase are reviewed in this article. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 1, 2014

By N. F. Fiore, M. F. McGuire

THIS communication describes a series of experiments in which dislocation etch pitting was used to ascertain the depth of damage in crystals which were mechanically polished or which were cut with either a commercial metallographic cut-off wheel,* a com- All specimens were cut from single crystals of American Smelting and Refining Co. 99.999+ pct pure copper which were grown from the melt by the Bridge-man technique. The test specimens were disks, with faces being (111) planes and the disk axis a (111) direction. The disks were annealed in a vacuum of 10-5 Torr for 24 hr at 950°C prior to cutting or polishing and were given a light electropolishing in an ortho-phosphoric acid bath before etch pitting. Both Youngs1 and Livingston's2 reagents were used for etch pitting and the reagents gave identical quantitative results; however Livingston's reagent produced less staining and so all photomicrographs shown are of {111) surfaces etched with this solution. The surface of the annealed crystals showed well-defined subboundaries and a density of dislocations of about 1 X 106 per sq cm excluding those present in subboundaries, Fig. 1. The depth of cold work produced during mechanical polishing was determined after an annealed specimen was mounted in a paraffin holding block to protect it from extraneous damage. The exposed (111) surface was ground on metallographic papers and then polished on billiard cloth through 0.05-p alumina abrasive. It was necessary to remove about 0.3 mm (-0.01 in.) to obtain a structure representative of the annealed sur- face, indicating that the crystal was damaged to this depth during mechanical polishing. The cold work caused by standard cutting methods was measured in another series of tests in which cuts

Jan 1, 1967

The risk associated with mining induced seismicity is one of the major threats to the safety and sustainability of deep underground mines. This paper describes techniques that allow site practitioners to efficiently control such risks in mines. The proposed approaches rely on ground support to strategically control seismic risk and re-entry time to tactically control this risk. The strategic approach is based on the detailed understanding of past seismicity to as certain the seismic hazard of individual sources throughout the mine. This approach also relies on assessing the potential damage that these sources can induce on nearby excavations using the excavation vulnerability potential (EVP) and rockburst damage potential (RDP) concepts proposed by Heal et al. (2006). It is then possible to investigate how to reduce the risk of experiencing damaging seismicity in mine drives by locally enhancing the ground support system. The tactical approach relies on a proposed methodology to estimate reliable re-entry times or exclusion periods based on the seismic decay following blasting. Some examples of how these techniques have been applied in Australian mines are given.

Jan 1, 2009

By Ananda Moreira Vaz Ourique de Avila

High and intermediate temperature fuel cells (FC) are power generators characterized by high efficiency and their use in cogeneration systems. The single fuel cells are connected in series by the use of interconnects to form a fuel cell stack. Ferritic stainless steels have been used in the making of high and intermediate temperature operation solid oxide fuel cells interconnects. However, at high temperatures, on the order of 700-8500C, these steels can present significant oxidation and degradation processes, promoting increased electrical resistivity and corrosion losses that result in contamination of the electrodes and reducing the performance and the useful life of the FC. Intensive R&D activities have been made to minimize these problems and the use of composite coatings on metallic substrate has been considered. This paper evaluates the use of coatings of copper and nickel, with particles of La2O3, Y2O3, CeO2, LaCrO3 and doped chromites applied on ferritic stainless steels AISI 430, AISI 441 and Crofer22APU produced by electrodeposition. The produced samples were evaluated by microscopy techniques, gravimetric analysis and by electrothermal characterization. The most significant results were obtained with chromites coatings (LaCrO3 pure, mono- and multiple-doped) showing the combination of the best features of metal coatings, substrates and ceramic particles with semiconductor properties.

Aug 7, 2018

By Clarence Hicks

THE labor policy, of the Standard Oil Co. (New Jersey) is founded. first of all on paying at least the prevailing scale of wages in the community; on, the eight-hour day, with time and one-half for overtime; one day's rest in seven; sanitary and up-to-date working conditions; just treatment assured each employee; payment of accident benefits beyond the amount prescribed by the State compensation law; health supervision by a competent medical staff; payment of sickness benefits after one year's service; cooperation with employee in promoting thrift and better social and housing conditions; and assurance for a generous annuity at the age of 65, guaranteed for life after 20 years of service. Most of these features have been a part of the company's policy for many years, but it is only during the past two years that the cooperation of employees in determining these matters has been definitely assured through industrial representation. Industrial representation, in the Standard Oil Co., is a principle rather than a procedure. It is built upon the belief that personal association of those interested in any problem leads to a mutual understanding and a fair decision as to what is right. Fully believing in this, principle, representatives of employees and representatives of management evolved a simple plan, the basis of which is that it gives every individual employee representation at joint conferences on problems and fundamental principles affecting all those interested in the industry. It is based on cooperation, not antagonism; its operation makes perfectly clear both to management and to employees that their interests are identical, that mutual understanding and cooperation insure progress and success for all. Furthermore, experience has definitely shown that representatives of the employees are not only alert for the employees' interests but are as keen as the representatives of the management in determining and insisting upon fairness to the employer.

Jan 3, 1920

Argentina follows Venezuela and Mexico as the largest producers of crude petroleum and natural gas in Latin America. Argentina 1S practically self-sufficient in fuels, but relies substantially on imports for its supply of copper, iron ore, ferroalloys, sulfur, and fertilizers. Mining activity is limited and is in an incipient stage of growth, considering the country's potential for mining. Most nonfuel mineral output in 1979 consisted primarily of minerals used for construction, while only 9% are other nonmetallic, and 2% are metallic minerals. Argentina is Latin America's major producer of boron minerals and uranium (yellow cake). Mineral exports consist primarily of borates, uranium concentrates, and of late, some tin. These exports have in the past been shipped mostly to Great Britain. London banks have been involved in arranging financing for St. Joe Minerals Corp. IS planned development of the El Pachon copper deposit (see map), and were being counted upon to also back the development of large copper and manganese projects. The following is a review of Argentine mineral production in 1979: (For 1981, the production of boron minerals is put at 167,000 metric tons and uranium at 300,000 metric tons.)

Jan 1, 1982

By V. R. Shea-Albin

This U.S. Bureau of Mines report discusses elastic wave velocity and attenuation behavior as an indicator for changes in load and structural integrity of coal samples. Measuring changes in compressional (P)-wave and shear (S)-wave attenuation and velocity under uniaxial and triaxial compression tests revealed their effectiveness for distinguishing changes in applied load and structural failure of samples. The velocity and attenuation values were used in further calculations such as ratios of P-wave to S-wave values, dynamic elastic constants, normalized velocities, and attenuation coefficients to reveal trends for loading and failure. The behavior of both P-wave and S-wave attenuation and velocity together define distinct and consistent phases of load change and failure for uniaxial and triaxial tests. The S-wave velocity and attenuation illustrate changing axial load and initial development of microfractures within the sample preceding structural failure more clearly than those of the P-wave. The attenuation and velocity ratios and dynamic elastic constants (except the bulk modulus) respond to closure of small preexisting fractures within the coal sample with initial loading to failure of coal samples. The attenuation coefficients and normalized velocities reveal trends similar to those shown by velocity and attenuation.

Jan 1, 2010

By J A. de la Torre, I R. Cerna, G K. Karadjian

The La Colorada underground mine in Zacatecas, Mexico is a mechanised cut-and-fill silver mine with a capacity of 1250 t/d. The project focused on training the mine’s experienced operators for a fleet of underground trucks, through the use of a training simulator. The project was run by the simulator vendor, in collaboration with the mine’s maintenance, safety and production management.A training program was created targeting maintenance reduction, productivity improvement and increased utilisation and availability. Operators were first acclimatised to the simulated environment, had their current performance baselined, then received targeted coaching, with the process repeated to reinforce learnings. Concurrently, production, maintenance, and safety data was being measured in the real world to measure skills transfer. Due to limited telemetry available from the equipment, many of the data points for the project were sourced from maintenance logs, and accounting data.Equipment failure data measured from unscheduled maintenance records showed an overall 6.5 per cent decrease in unscheduled maintenance following the implementation of the training program. This rate of reduction correlated with the significant decrease in equipment abuse behaviours measured within the simulator during this period. Additionally, overall maintenance activities showed a significant decrease, confirming that reductions in unscheduled maintenance were not achieved through increases in scheduled maintenance. The reduction in equipment damage also increased availability and utilisation of the truck fleet. This highlights that the maintenance improvements not only reduced maintenance costs, but made the fleet available for more production. Moreover, the variability of the operator performance was decreased by 86 per cent, and the difference between their best operator and the worst is less than the baseline; this showed a gap where machine abuse, productivity and cost are impacted directly.This project illustrated that even small-scale mining operations with an experienced operator workforce can achieve positive return on investment (ROI) from simulation-based training. It also highlights that in the absence of equipment telemetry, alternative data sources such as accounting data and maintenance logs can be used to quantify ROI from training.CITATION:Karadjian, G K, de la Torre, J A and Cerna, I R, 2017. Innovations in underground hard rock operator efficiency – through simulation-based training technologies and processes, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 53–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By William Hanco, Carlos Calero

La inclusión de tecnologías 3D en las plataformas de Sistemas de Información Geográficos (GIS) corporativas viene potenciando la labor de Osinergmin, cuya Gerencia de Supervisión Minera está encargada de asegurar el cumplimiento de las normas relativas a la seguridad de la infraestructura de la mediana y gran minería. El artículo describe cómo la captura de aerofotografías de componentes mineros de interés, tomadas con cámaras de alta resolución desde vehículos aéreos no tripulados (drones), son procesadas luego para obtener modelos digitales en 3D, sobre los cuales se realiza la medición de magnitudes físicas para verificar, en gabinete, que los parámetros técnicos de los componentes analizados cumplen con lo autorizado. De este modo, no solo se logra cubrir una mayor área de supervisión, sino también focalizar el trabajo de campo en aquellos puntos donde se encuentren observaciones.

Sep 20, 2019

By Cheng Lin, Guoming Lin

"This paper presents a case history for the design, construction and long-term performance monitoring of a driven prestressed concrete (PSC) piled foundation supporting a large liquefied natural gas (LNG) tank in Savannah, Georgia, USA. Following a geotechnical investigation, a design stage pile test program was performed with three objectives: to study the densification effect from pile driving on the liquefaction resistance, to test axial and lateral pile capacities, and pile behavior under lateral loads. The test program comprised five piles driven on a test pad constructed adjacent to the tank foundation. Cone penetration testing (CPT) was performed before and after pile installation to test soil densification effects from the pile driving and liquefaction potential was re-evaluated based on the soil densities after pile installation. The axial load tests involved static load testing, high strain dynamic testing, and Statnamic testing. This paper presents the findings of the densification effects, compares results from different axial testing methods and discusses the procedures to use the load test results in the pile design. The paper also comments on the construction issues and presents performance data with 10 years of monitoring.1. IntroductionThe project site is located at the Kinder Morgan’s Elba Island LNG Terminal on the Savannah River which is three miles downstream of the downtown Savannah, Georgia. This LNG terminal was initially developed in the 1970s as an LNG import terminal. The facility includes five LNG storage tanks with two larger tanks which were constructed in 2003 and 2006, respectively. The terminal is currently being converted into a liquefaction and export facility. This paper discusses pile foundations for Tank D4 which is a double walled insulated steel tank built to hold one million barrels of LNG in 2003. This tank has an outer tank diameter of 258 feet, an inner diameter of 252 feet, and liquid height of 113 feet. A number of geotechnical challenges were present in the foundation design and construction.??The site is a typical coastal deposit site featuring a thick layer of very soft under-consolidated clay (up to 40 feet in thickness);??The bedrock is a couple of thousand feet deep;??There is a sand layer that is liquefiable under a high seismic design category (0.5% possibility of exceedance in 50 years)."

Jan 1, 1900

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device IntroductionTwo recent regulations have modified operators’ rock dusting schedules in order to meet compliance standards. First, the 80 percent incombustible requirement in intake entries has increased both on-section and out by the- section rock dusting. Secondly, the recent change to the respirable dust regulation has increased the number of respirable dust samples taken per sampling cycle. Previously, when only five samples were needed bimonthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule.The significant number of samples now required under new regulations, combined with the need to maintain 80 percent total incombustible content in active mining areas, require the schedules for respirable dust sampling and rock dusting to overlap. Although rock dust is considered a nuisance dust in relation to U.S. Mine Safety and Health Administration (MSHA) sampling, these overlapping schedules raise concerns about the amount of rock dust that potentially is included in the sample. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 effective Aug. 1, 2016, increasing concern that rock dust contamination may be an issue (MSHA, 2016). Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application, or to schedule rock dusting during a maintenance shift when the number of miners present is lower."

Jan 5, 2017

By Robert E. Barieau

In the design of plants to separate helium from natural gas , it is necessary to estimate the enthalpies of the various streams at various positions in the process . This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities . The minimum information required for developing an enthalpy diagram is presented , and the relative merits of the various methods are discussed . It is concluded that methods that require no mass flow rate or energy measurements are to be preferred .

Jan 1, 1965

By -Ing. Alexander Dohmen, -Ing. Gunter Hagen

In order to improve the thermal environment in deep coal mines, two principles can be applied: firstly, the reduction of heat flow into the air stream, and secondly, cooling of the air current. First of all one should try to minimize the heat-flow rate into the air stream underground by the mining method itself. German coal mines prefer the caving system of advance longwall mining simultaneously on several levels with ascensional ventilation. The effects of descensional ventilation and different face ventilation layouts on the thermal environment are discussed, besides the effects of pneumatic and hydraulic stowing. Application of all mentioned possibilities together instead of today's common mining method would reduce the Basis Effective Temperature considerably. In the future, hydraulic haulage of the raw coal underground substituting belt conveying may be a mean to improve the thermal environment further on. If the working depth of a coal mine exceeds about 1 000 m, cooling of the air stream under-ground will be necessary in addition to the above- mentioned measures. Generally, in German coal mines different types of indirect-contact air coolers located nearby the face are used. Besides such so-called cooling coils, large-capacity spray coolers are used because they work more efficiently if a great cooling duty is demanded. Common designs of both air cooler types and their possible utilizations are demonstrated. Deep coal mines in the Federal Republic of Germany need up to 30 MW of total cooling capacity. Mostly, the needed chilled water is cooled by large-capacity refrigeration plants placed on surface, underground or in combination of the above locations nearby the shaft. Due to the increasing underground cooling demand, the distribution of the chilled water and the control of the air coolers become more important. The conception of a control system is discussed, which is based on the control of the single air coolers. All air coolers of a mine are controlled so as to optimize the supply water-flow rate with regard to the demanded cooling duty of the coolers. On the next upper level of the control system the whole chilled water network and finally the refrigeration plant is regulated. Present research work deals with the use of ice for cooling mines. There are some unsolved problems in this new cooling concept. Some aspects of making, transporting and storing ice are described. The use of ice may probably reduce the cooling costs of German collieries, which are at present approximately 4 DM per ton of saleable coal.

Jan 1, 1989

By T. T. Campbell

Although secondary recovery of lead and lead-tin alloys has been common practice in the United States during recent years, there is little published in-formation concerning recovery techniques. Available information does not cover metal recovery from wet dross skimmings. This investigation by the Bureau of Mines was undertaken to develop techniques that would allow lead-tin alloys to be recovered from wet dross skimmings containing large amounts of zinc chloride. A process was developed, on a laboratory scale, for recovering lead-tin alloys from wet solder dross skimmings. Straight water leaching, either with or without a second leaching operation carried out with a Na2C03 addition for removing chloride, produced a dross that could be smelted without further treatment. Overall recoveries averaging 92 percent of the metal values in the dross were obtained in the form of lead-tin alloys, which had an average tin content of 16 percent and lead content of 84 percent. The recovered alloy contained less than 0.02 percent zinc, as determined by both chemical and spectrographic analyses.

Jan 1, 1956

By Jiongtian Liu, Guihong Han, Shuzhen Yang, Yanfang Huang

Binder, as a necessary functional material of electrode in lithium ion battery, has a vital influence on the electrochemical performance. The humics, coupled with polyacrylamide (PAM) and sodium carboxymethyl cellulose (CMC), were used as a water-soluble binder for LiFePO4 (LFP) cathode using in lithium ion battery. The techniques of cyclic voltammetry (CV) and galvanostatic charge-discharge were conducted to evaluate the performance of humics binder in LFP electrode. The reversible specific capacity of LFP (HA + PAM + CMC) electrode can reach to 142 mAh g−1 after 50th cycling (100 mAh g−1) on conditions of raw materials with 1 wt% PAM addition, humics and CMC with a mass ratio of 3:1 in binder, and the raw materials mixed in an interval order. Humics has the potential to be used as a novel, eco-friendly and high-efficient binder for lithium-ion battery.

Mar 1, 2018

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000-2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A * R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By Werner Klein

The Production Management solution (Level 3) covers TYASA’s existing steel making plant, billet caster and new Castrip based coil production line in Ixtaczoquitlan, Mexico. It steers the order based production utilizing product routing information and corresponding process instructions for the individual processing units. A seamless material tracking along the entire production route from heat creation in the electric arc furnace down to the final coil product provides TYASA with the genealogy information customers require for flat products. At each important process step the Level 3 compares actual quality related production results with order requirements. In case of deviations from ordered quality the plant staff is guided by rule based dispositions. The highly configurable solution supports customer to operate its production plant as a smart factory in the sense of industry 4.0.

Oct 30, 2017

By W. J. Witte, M. K. Witte

"The purpose of this report is to present a generalized preliminary design and cost estimates for a typical heap leach operation such as might be undertaken in Northern Ontario. This report should be of value to anyone in the mining industry planning, or contemplating, a heap leaching operation in Ontario, either on a large or small scale. While more detailed costing and design work will obviously be required for each specific project being contemplated, the data provided in this report should enable parties to make preliminary estimates of the costs of proposed projects and should identify most of the planning and design parameters that will need to be considered.Although heap leaching has been used extensively as a low cost gold recovery method in other parts of the world for many years, it has only recently become of interest to the Canadian mining industry.In order to investigate and demonstrate the feasibility of using heap leaching in Ontario, the Ontario Ministry of Natural Resources in 1982, undertook to locate a private sector proponent willing to undertake a 10,000 ton demonstration project. This project was to have been carried out at a production scale under normal northern Ontario field conditions. The Ministry was to have provided technical management and design for the designated project."

Jan 1, 1985

By Joseph M. Kurtak

The U.S Bureau of Mines conducted a five-year mineral resource assessment of the 16.6 million acre Colville Mining District in northern Alaska, which includes part of the National Petroleum Reserve in Alaska. The study was initiated at the request of the Bureau of Land Management, which administers the majority of the region. The study was done in cooperation with the Alaskan Division of Geological and Geophysical Surveys, the U. S. Geological Survey, and the University of Alaska. During fieldwork, 1593 rock, soil, and stream sediment samples were collected and four bulk samples taken for beneficiation studies. A total of 40 mineral occurrences were documented, including 27 which were previously undescribed. No mining has occurred within the district. Mississippian carbonaceous shale and siliceous mudstone contain stratiform exhalative lead-zinc-silver occurrences. Grades average 8.0% combined lead/zinc and 51 gm/mt silver. Upper Devonian to Lower Mississippian sandstones host breccia veins, containing up to 29% combined lead/zinc and 274 gm/mt silver. Mineralized quartzites of similar age have potential for disseminated-type lead-zinc deposits. Samples from Lower Cretaceous mudstone and shale beds up to 6.5 meters thick, contain as much up to 12% manganese. Upper Mississippian carbonaceous shale and limestone beds contain up to 23% phosphate. Stratiform barite deposits hosted by cherts, are up to 27 meters thick with an average specific gravity of 4.16. Vein-type fluorite occurrences are associated with Mississippian limestone. Moderate potential exists for development of zinc -lead-silver, barite, and phosphate deposits.

Jan 1, 2011