Search Documents

By R. W. Schenker

INTRODUCTION Environmental and occupational safety and health requirements often have a major impact on the design of comminution circuits, leading to increased capital and operating costs and reduced income. A project's capital cost can be increased by environmental permitting delays and the addition of dust collection equipment. Income can be reduced by lost production during unscheduled plant shutdowns for dust collection equipment maintenance. Dust collection equipment must be carefully selected and sized to minimize impact on the project. The equipment performance must comply with environmental regulations and allow working areas to comply with occupational safety and health regulations. Unnecessary overdesign could jeopardize the project's desirability from an economic standpoint. The equipment must be sufficiently reliable to avoid interference with production schedules. This chapter provides practical information on the selection and sizing of comminution circuit dust collection equipment that is consistent with the requirements stated above. It presents information on the reasons and general principles of dust collection; various types of dust collection equipment; and design criteria for ventilation hoods, duct systems, fabric filter dust collectors, and fans. An example discussing the selection and sizing of dust collection equipment for a simple comminution circuit is also presented. REASONS FOR DUST COLLECTION Dust collection equipment should be installed in comminution circuits for a variety of reasons, some of which are discussed below. These include compliance with government regulations, minimization of housekeeping requirements, product recovery, and improvement in public and employee relations. Compliance with Government Regulations Dust emissions from comminution circuits must comply with both air pollution control and occupational safety and health regulations. The regulations that may influence the selection of comminution circuits are discussed in more detail in Chapter 2. Air pollution control regulations limit the emission of dust, as well as visible emissions to the atmosphere and the concentration of dust in the ambient air. These regulations minimize the degradation of air quality and impact to other environmental considerations such as the health of the general public,

Jan 1, 1982

By Simón Díaz‑Quezada, Ernesto Arancibia, HUMBERTO ESTAY, Tomás Vargas

In situ leaching (ISL) is an attractive technique that enables copper recovery from copper oxide ores that are either low-grade or located at depths too great to be economically exploited through conventional methods. At present, in situ leaching (ISL) has been applied to intact copper oxide ores, in particular, those which (i) present a good natural permeability and (ii) do not require preconditioning. Many copper oxide ores present low natural permeability. These are located above the water table and need preconditioning for the ISL application. The present work shows an economic assessment of the application of ISL to this type of copper ores. The preconditioning technique considered here involves the application of partial mining by sublevel stoping by removing a small fraction of the ore. This technique results in forming an ore bed with good permeability and good solution collection at the stope base. The economic assessment of this approach suggests that it can be implemented with positive net present values to copper oxide ores located at depths in the 100–300 m range, with copper grades above 0.4%. The maximum acid consumption values are below 52.5 kg/t, with blasting procedures designed to produce an ore bed with an average particle size below 6″. The breakdown of operational costs indicates that the mining cost is still very high, accounting for up to 60% of the total operating costs. Therefore, optimizing mining procedures is still necessary for improving the economic outlook of this approach and thus expanding the application field of ISL.

Feb 4, 2023

By B. K. Saikia

A preliminary attempt has been made to study the particle size distribution (PSD) of minerals in one of the industrially important pulverized Indian coal sample using computer-controlled scanning electron microscopy (CCSEM). The results show that clay minerals, quartz, pyrite, and pyrrhotite form the bulk of the mineral matter. Minor minerals, such as calcite, dolomite, ankerite, barite, oxidized pyrrhotite, and gypsum are also observed in the coal sample. The PSD of the included minerals is generally observed to be finer than that of the excluded ones in the coal. Thus, the coal rich in included minerals has more small mineral particles, which may affect its reactivity. The proportion of included to excluded is found to be higher in major cases. Si is found to be mostly occurred as quartz and clay minerals, while Al mostly occurs as silicate minerals. Fe is primarily present as iron sulfides, iron oxide, and Fe-Al-silicate. S is partitioned into iron sulfides and gypsum. Most Ca occurs as carbonates and gypsum, with a minor fraction associated with clay minerals. Mg is found to be mainly present as dolomite and clay minerals, with a very minor fraction present as ankerite. The majority of alkali elements are associated with aluminosilicates. P is mostly associated with kaolinite and/or present as more complex compounds containing Al, Si, and other elements as apatite are found to be absent in the coal studied. Ti is mainly present as rutile and kaolinite. The geo-chemical association of the trace elements has also been discussed. Keywords: minerals, Assam coals, Indian coals, CCSEM study

Sep 1, 2012

By W. E. Wallace, V. Robinson, M. F. Keane, V. Vallyathan

"An in vitro study of the biologic responses of surface-modified and native silica and kaolin was made to provide comparative information on the supression of cytotoxicity by pulmonary surfactant. The release of alveolar macrophage cytoplasmic enzyme, lactate dehydrogenase (IDH), and lysosomal enzymes B-N-acetylglocosaminidase (B-NAG) and B-ghucuronidase (B-GLUC) and sheep blood-cell hemolysis were moni¬tored as indicators of cell membrane damage and cytutoxicity. Surface modification of silica and kaolin with dipalmitoyl lecithin (UPI) resulted in complete abrogation of cytotoxicity of both minerals. These findings indicate that surface modification of minerals with different adsorption properties by pulmonary surfactant generally lessens their prompt adverse effects.INTRODUCTIONAcute and chronic silicosis are well-characterized clinical and pathologic entities resulting from the inhalation of crystalline silica (Morgan and Seaton, 1984). Kaolin, a layered aluminosilicate clay frequently mined and used in manufacturing, contains tetrahedral silica alternately layered with alumina octahedra. Kaolin is relatively .inert biologically, and distinctly greater pulmonary burdens are seen in patients with kaolinosis than are seen in patients with silicosis. Crystalline siliea (quartz) induces a significantly greater degree of fibrosis in exposed animals in vivo than does kaolin (Hamilton and Hardy, 1974; Parkes, 1982; Hunter, 1976; Sheers, 1964; Warraki and t-lerant, 1963; Lynch and Mciver, 1954; Lapenas et al., 1984).This difference in pulmonary disease associated with the two types of dust is not reflected by in vitro cytotoxicity as Jetermined by pulmonary macrophage bioassays or erythrocyte hemolysis. Cytotoxicity studies using crystalline silica and kaolin of similar size fractions show comparable bioassay response on a mass basis. These cellular bioassays, therefore, do not correlate with the relative in vivo pathogenicity of silicates."

Jun 1, 1988

By F. Nakhaei, M. Le Roux, Q. P. Campbell, S. Botlhoko

The results of coal sink and float tests are plotted as washability curves. Analysis of these curves indicates the most effective method by which the coal can be cleaned. Sink and float experiments are samplingdependent, destructive, and use toxic chemicals. The present research introduces an alternative method based on a 3D imaging system called RhoVol, in which the density of individual particles is determined from mass and volume measurements. A quantitative error analysis was conducted on coal sample density measurements obtained by RhoVol, and the main factors influencing the errors identified and investigated. The results show that the drawback of this technique is related to its not being able to detect hidden concavities in the particle, resulting in an overestimation of particle volume. Furthermore, it is difficult to capture the impact of porosity and cracks on the volume of coal particles obtained from 3D silhouette images. This mismatch between the RhoVol data and sink and float test results has led to attempts to apply neural network (NN) and linear regression techniques to produce a fully reliable model for correction and estimation of coal density. The NN approach offers superior predictive capability over linear regression, and the estimated density distribution is in line with the sink and float analysis. The root mean square error in estimation of density using the NN model was less than 0.05 g/cm³.

Aug 2, 2022

By Diego Pinheiro Aun

Neste trabalho, foi investigada a influência da textura de fitas de NiTi superelástico no início do processo de cristalização de um revestimento de TiO2 flexível. Foram utilizadas a calorimetria diferencial, cartografia Raman e difração de raios X para o estudo. Foi mostrado que existe uma influência significativa da textura do substrato no crescimento de grãos de anatase e rutila no filme de TiO2. Amostras com menor rugosidade apresentaram grãos mais desenvolvidos para todas as temperaturas de cristalização. Mostrou-se também que o substrato de NiTi promoveu a formação de TiO2 rutila em temperaturas abaixo daquelas observadas para a cristalização de pós.

Aug 16, 2017

By A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia?s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By Adrian J. Moore, Alan B. Richards

Responsible blasting requires that rock throw be controlled to ensure that no danger will result to people and property. This paper describes the development and testing of empirical field calibrated formulae that can be used to evaluate rock throw, provide an early warning of when reduced burden will endanger people and property, and prevent flyrock incidents. Inputs to the formulae are charge mass, burden or stemming height, and a site constant that lies within a general range that can be tightened by site calibration. The output is the distance that rock will be thrown, and this ‘design your own flyrock’ quantification can be used to establish both safe clearance distances, and the critical range of burdens and stemming heights where the situation changes rapidly from safe to hazardous. Examples are given of the use of the model to control flyrock in open-pit mining and quarry operations, in situations which are controlled by both burden and stemming height.

Jan 1, 2004

By W. G. Davenport

This chapter extends our mathematical description of flash smelting to -nitrogen in the flash furnace blast. As in chapters 4 and 5, the discussion is limited to auto thermal smelting (no hydrocarbon combustion). Hydrocarbon combustion is introduced in Chapter 9. Outokumpu flash furnace blast is a mixture of air and industrial oxygen. Most of its N2 originates in the air portion of the blast. A small portion originates as an impurity in the industrial oxygen. The nitrogen entering a flash furnace must always be heated from its input temperature, 298 K in this chapter, to its off gas temperature, -1500 K. Energy must be supplied for this purpose. With auto thermal smelting, the energy is-provided by oxidizing extra Fe-and S.

Jan 1, 2001

By Alejandro Ferrada Vergara, María Jesús Barros Godoy

The need for a basic method for selecting explosives based on rock mass or intact rock properties for mining and construction arises from the limited consideration given to these factors when choosing among products and also an implicit overestimation of the explosive power to fragment the rock. This study highlights the importance of evaluating different properties such as rock strength, deformation, fracturing, detonation velocity and energy release when selecting explosives. The concept of characteristic impedance, which considers rock strength against shock waves generated by explosive detonation, is introduced. Understanding this concept is crucial for assessing explosive behavior according to various rock types. The study concludes with a practical guide table that categorizes rock properties and provides recommendations for selecting explosives based on rock mass and rock properties. However, it is important to consider other relevant factors, such as the presence of water or nearby instabilities, which can influence the final choice of explosives.

Jan 21, 2025

By J. A. Luppens

Five years ago, Phillips Coal Company decided replacing mainframe/workstation programs with a new package of PC software was clearly the best solution for computer reserve modelling. The system chosen was actually three programs distinguished by their power, cost, flexibility and integration, and ease of learning and use. Phase I involves the use of the "StratiFact" program for borehole data management and seam correlation. This phase is probably the most neglected, yet critical aspect of reserve evaluation. Phase II employs the "PC/Cores" package for modelling and volumetrics. Phase m is "PC-Cut" which provides mine planning tools including an automated cut generator.

Jan 1, 1996

By T. Braun, J. Parker

On June 25, 1999, BHP Billiton (BHPB) announced the suspension of operations at the BHP Copper Inc.(BHP) San Manuel copper mine in Pinal County, Arizona. Subsequent to this announcement, BHPB aggressively pursued a number of alternatives for the underground mine and open pit facilities, including continued curtailed operations, sale to a qualified mining operator and closure of the property. After consideration of these various alternatives over a 2.5-year period, BHPB announced final closure of the mine site on January 15, 2002.This paper describes how the BHPB charter and HSEC policy apply during the closure process.

Jan 1, 2004

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

By Dong Maolin

A great amount of high temperature off-gas, whose maximum temperature is up to 2100?, is generated during the smelting process of electric arc furnace (EAF). The dust content, which is mainly iron oxide, of the off-gas is high and worthy of industrial recovery. The heat carried by the high temperature off-gas with dust is about 11% of the total energy input of EAF, and some even is as high as 20%. The high-temperature off-gas not only takes away a lot of heat but also places a huge burden to de-dusting system of EAF. It not only reduces the iron oxide dust recovery ratio, but also causes serious pollution problems. With the development of the iron and steel industry, the proportion of molten iron for EAF gradually increases, and even more than 30% in some cases. The increase of molten iron causes increases in the amount of EAF off-gas and heat waste. As a result the problem of dust removal is worsening [1-2]. How to sufficiently recover the sensible heat of the high temperature off-gas, create conditions for efficient dust removal, thus reduce operating costs of dust removal system and the production costs is a problem which EAF steel making companies must pay attention to.

Oct 30, 2017

By L. E. Green

For shortwall mining to be profitable, the additional capital investment of about $1 million for shortwall roof supports must be offset by decreased total operating costs and/or increased coal production. The Bureau of Mines therefore conducted a demonstration project to compare shortwall and room-and-pillar mining. Daily two-shift production from the bureau of Mines-Beth-Elkhorn Corp. shortwall demonstration n project averaged 975 tons of raw coal, compared with 905 tons from a room-and-pillar unit operating undo r similar conditions. The estimated direct operating costs for the shortwall and room-and-pillar unite were $4.21 and $4.03 pier ton, respectively. The profitability of the shortwall system was found to depend not only on the increased depreciation cost of the powered roof supports and the decreased cost of supplies and materials but also on such factors as the fixed and variable indirect costs and the selling price of the coal. Shortwall mining was demonstrated to be a viable alternative to room-and-pillar mining.

Jan 1, 1977

By A. W. Henderson

This investigation was performed to develop chlorination methods for extracting tungsten from scheelite and from an ore concentrate containing a mixture of scheelite and wolframite. On a laboratory scale with proper temperature control using elemental chlorine, over 90 percent extraction of tungsten is achieved. Carbon and sulfur dioxide were studied as reducing agents. The effects of salts such as calcium fluoride and sodium chloride were studied as additives to increase extraction and to reduce impurities in the volatile tungsten chloride product. Sodium chloride reacts with ferric chloride to form a nonvolatile double salt; whereas the chlorides and oxychlorides of tungsten are volatile and consequently condense free of iron. Separation of tungsten from molybdenum from an equal molar mixture was successful by fractionally distilling the oxygen-free chlorides and by selectively condensing the oxychlorides. Yields of 60 and 80 percent, respectively, were achieved for separating the less volatile tungsten chlorides containing less than 0.5 percent molybdenum.

Jan 1, 1965

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013