Search Documents

By Richard H. Oitto

With increased interest and urgency for coal mine safety and the passage of the Federal Coal Mine Health 'and Safety Act, the Bureau's research effort in roof control has been greatly expanded. One new project, the subject of this paper, concerns improving conventional roof bolting and has been involved with the effects of different variables on the performance of roof bolt expansion anchors. These include types of expansion anchor, rock type at the anchorage horizon, borehole roughness, rate of torquing a roof bolt to set the anchor, installed tension, bolt length, and relative humidity fluctuations. For this work, two types of experiments were carried out. One was concerned with tension loss in bolt-anchor assemblies and simulated anchor performance in a static roof. The other dealt with anchor slippage as tension was increased and simulated anchor performance in an active roof. Trials were made in the laboratory under controlled conditions so that factors suspected of affecting expansion anchor performance could be selectively studied. Because of the natural variability in rock and the fact that most expansion anchor components are essentially rough castings or forgings, the experiments were designed to permit using analysis of variance techniques for analyzing data. Thus, in this paper, "significant" means statistically significant.

Jan 1, 1972

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By W. W. Rudolph, L. N. Trevani, P. R. Tremaine

UV-visible spectroscopy, Raman spectroscopy, and vibrating tube densimetry have been used in our laboratory to determine equilibrium constants of aqueous species at temperatures as high as 325 °C. The UV-visible and Raman spectra of solutions containing metal complexes and ionized acids or bases can be used to yield formation constants by applying curve fitting methods to resolve the contribution of each species. Colorimetric pH indicators identified by Johnston and coworkers at the University of Texas (Austin) provide an alternative means of determining ionization constants and the pH of complex mixtures. High precision density measurements over the same range yield standard partial molar volumes, which are key parameters for "equations of state" for aqueous species. Examples are given for the copper-ammonia system, simple carboxylic acids, and the iron-sulphate system.

Jan 1, 2004

By Dale E. Wittmer

Nonoxide ceramic materials could substitute for high-temperature alloy steels containing imported critical and strategic materials such as cobalt, chromium, and nickel if their high-temperature properties can be improved. An important result of this substitution would be a reduction of the Nation&apos;s need for imports of critical and strategic materials. In this Bureau of Mines investigation, the primary objective was to produce high-purity u1trafine (particles <5 ~m equivalent spherical diameter (ESD)) alpha-silicon carbide (a-SiC) powders with improved high-temperature properties using the Bureau&apos;s patented turbo-milling process. A secondary objective was to determine the feasibility of using polymer mill construction materials as a means of eliminating metal contamination from the turbomill. U1trafine a-SiC powders with BET (Brunauer-Emmett-Te11er) surface areas from 30 to 35 m2/g (~0.06 ~m particle ESD) were produced in an all-polymer turbomi11. These high-purity powders (with I-pct Band I-pct C additions) hot-pressed to greater than 99 pct of their optimal density and exhibited properties commensurate with those of commercially available a-SiC. The most promising of the construction materials tested for the major wear surfaces of the turbomi11 was u1trahigh-mo1ecu1ar-weight (UHMW) polyethylene, a polymer thermoplastic.

Jan 1, 1984

By Richard P. Walters

This Bureau of Mines report reviews and assesses the technology for preparing electrodeposited coatings of the platinum-group metals from molten alkali metal cyanide baths. Methods are described for the preparation and purification of the cyanide electrolyte. Vacuum drying, fusion, and purity of the cyanide salts are discussed. Use of a sodium borosilicate test tube as a sodium-ion-conducting membrane for the addition of the desired platinum-group metal is described. The optimum plating parameters of potential and current density for Pt, Pd, Rh, Ru, and Ir coatings that result in the best deposits are given. A method for producing platinum-rhodium alloy coatings of predetermined composition is also described. The importance of careful substrate surface preparation is illustrated. While problems still remain with respect to coating porosity, careful application of the methods described permits the preparation of adherent, coherent electrodeposited coatings of the platinum-group metals.

Jan 1, 1984

By Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"Over the last 10 years, the Minnesota Department of Transportation (Mn/DOT) has had a very active program of replacing many major bridges, large structures spanning the Mississippi River. The deep foundations for these new structures include both drilled shafts and large diameter open-ended driven steel pipe piles. Most of these projects included load tests, both axial and lateral.The geology of this area of Minnesota includes some interesting foundation challenges, including highly organic and compressible very soft silts and clays to very dense sand and gravel overlying sedimentary bedrock. In some cases scour requires embedment into rock, and the bedrock formations may range from very soft sandstone to very hard dolostone. Artesian groundwater conditions can sometimes complicate drilled shaft construction, but the rock is otherwise very favorable for drilled shafts. Experience with the open-ended driven steel pipe piles (typically 42 and 48 in, 1.07 and 1.2 m diameter) suggest that these piles most often penetrate even dense granular materials to achieve bearing on rock. Experiences with drilled shafts socketed into the soft sandstones demonstrate that these rocks provide very favorable conditions for drilled shafts, so long as suitable construction practices are followed. Here we present several recent case histories regarding the foundation design and construction of major bridge projects in the vicinity of Minneapolis, Minn., including the Wakota Bridge, the I-35W replacement, the Lafayette Bridge, the Hastings Bridge and the St. Croix Bridge. Some lessons learned from construction and load testing of both types of foundations are described along with implications for design in similar soil and rock conditions."

Jan 1, 2013

By C. Matthews, A. Vo

Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations. INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $20/tonne according to the Metal Bulletin Iron Ore Index (Fastmarkets MB, 2019). At a shipload of 180kt this would be a variation of US $3.6M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product.

Jan 1, 2019

By G. D. Bates

INTRODUCTION The Magmont mine is a joint venture of Cominco American Inc. (operator) and Dresser Minerals, Inc. The mine-mill operation is located approximately 160 km (100 miles) southwest of St. Louis, MO, in what is commonly referred to as the "Viburnum Trend.” The Magmont mine is designed for a production rate of 3810.2 t/d (4200 stpd) on a 5-day week, three shifts per day basis. Initial production began in 1968. The mine is open stope, room-and-pillar, and essentially horizontal along the trend of the ore body. Briefly, the main geological structure can be described as a brecciated graben bounded by reverse faults. The ore body in cross section is shaped like a bell curve with some lateral extension at the lower part. Presently outlined ore is 609.6 to 762 m (2000 to 2500 ft) in width and 2133.6 m (7000 ft) in length. The ore varies in thickness from 4.87 m (16 ft) on the fringes to an average of 27 m (90 ft) in the high ore areas bounded by the reverse faults. Lead is the primary metal with zinc and copper secondary. MINE DESIGN The basic design of open stope, room-and-pillar mines has been described by several writers and need not be repeated here. (Anon., 1970; Bullock, 1973; Casteel, 1972; Christiansen et a]., 1970; and Lane, 1964) This discussion covers the mining sequence as applied to the particular problems at the Magmont mine, the use of equipment, and deployment of the work force. In the upper portion of the Magmont ore body is a layer locally called the False Davis shale. This layer lies below the true Davis shale, is normally interbedded with dolomite, is of varying thickness, and if mineralized, is included in the top pass of the mining sequence. In thick ore areas this layer will be 2.13 to 2.43 m (7 to 8 ft) in thickness and will occur in the upper portion of the pillars. Due to its incompetency the presence of this False Davis layer is of primary concern in mine planning and operation. Mining areas are divided into three basic groups by ore thickness. First are areas of ore up to 6.09 m (20 ft) in thickness. These areas are below the False Davis shale and are mined single pass with drill jumbo. Second are those areas up 13.71 to 15.24 m (45 to 50 ft) in height. The first 4.87-111 (16-ft) Pass is taken at the top of the ore and the back and pillars secured. Benching the lower portion(s) in 4.57 to 4.87-m (15 to 16-ft) passes is then done with either a drill jumbo drilling horizontally or a crawler drill drilling vertically. Normally these areas are below the Table 1. Productivities per Manshift False Davis shale. These areas may also be mined by back slashing, or overhand benching, where the first 4.87-m (16-ft) pass is taken at the base of the ore and successive 4.87- m (16-ft) passes are taken upward. A minimum amount of back slashing is done at Magmont since it requires repetition of roof control on each pass and roof control is the single largest stoping cost at Magmont. Ore left to provide a working platform oxidizes and is coated by oil spills thus reducing metallurgical recoveries. The third mining area is over 15.24 m (50 ft) in height UP to a maximum of 40.23 m (132 ft) and will encompass the False Davis shale. These areas are mined by first driving +15% inclines to the top of the ore body. The top pass is mined and the back is bolted and roof mats installed as a matter of standard practice to minimize roof problems as mining progresses downward. Once the back and pillars on the top pass are secured, benching begins on successive passes with either the drill jumbo or crawler drill. Pillars on all successive passes below the top pass are secured as necessary. While benching progresses below the top pass, the pass at the base of the ore body is mined leaving a sill of 4.57 to 7.62 m (15 to 25 ft) in thickness to be removed with the crawler drill in a retreating manner. Rooms are mined on a 1.57 rad (90") grid pattern to insure alignment of pillars where multiple passes are taken. Pillars are designed on a 17.98-m (59-ft) spacing with rooms up to 10.66 m (35 ft) in width. Heading widths are wide enough for the mobile equipment to turn without additional allowance for curves. The result is a flexible layout which provides a maximum number of headings available for high extraction rates and grade control. PRODUCTION Incentive Bonus Incentive bonuses play an important part in the mine production at Magmont. Production crews are trained to perform only one of the mining functions of drilling, blasting, mucking. or roof bolting. This specialization, or functionalization, is augmented by development to open all possible stoping areas as early as possible in the life of the mine. This insures that each crew will have enough headings to perform its specialty. The incentive bonuses increase exponentially as output increases. The lucrative incentive bonus coupled with the specialization of the production crews and proper mine development have combined to give the high productivities shown in Table 1. Development crews perform all mining functions in their area. The incentive bonus is paid on a per foot basis, Crews on different shifts working the same heading share equally in the bonus proportional to their contract hours worked.

Jan 1, 1982

By John A. Davis, David W. Brunton

(Excerpts, pp 157-160) The usual means of firing blasting charges, especially in tunnels and adits in the Western States, is by the use of a safety fuse. The term safety fuse originated from the fact that when properly used under working conditions this fuse burns at a uniform rate and does not flash or explode, as was often the case with the means employed for igniting blasting charges previous to its invention; but the term is somewhat misleading, because the fuse is not, nor has it ever seriously been claimed to be, safe for use in gaseous coal mines. The fuse used for tunnel work is composed of a core of gunpowder surrounded by various layers of waterproofing material.

Jan 1, 2015

By R. Casagrande, L. R. Moore, J. Sessoms, P. Macy

"A South American nickel mine has been producing a nickel concentrate that also contains copper and iron (15 percent nickel, 5 percent copper, 28 percent iron) for the end use of stainless steel production. A critical specification for the quality of the steel is the iron to magnesium oxide ratio (Fe:MgO), with a ratio of below 3.5:1 having a substantial impact on the nickel value. This nickel concentrate producer historically mined the sulfur-rich mineral pyroxenite but had been forced to move to a magnesium oxide/silicate (MgO/SiO4)-rich mineral harzburgite, resulting in nickel recovery being reduced to around 50 percent to maintain the required Fe:MgO ratio. In this study, ore mineralogy, water chemistry and the chemistries associated with the flotation process were evaluated in an effort to increase nickel recovery while maintaining the Fe:MgO ratio according to specification. New chemistry was introduced with the specific goal of complexing with the MgO and retarding its interaction with the bubble flow in the flotation process.IntroductionGlobal nickel production in 2011 totalled to 1,770,000 tons, according to the Raw Materials Group (2013). From 1950 to 2005 there was an aggregate 4.4 percent increase in nickel production, with a market-value high of $1,000/ton nickel reached in 1998 (Mudd, 2010). Approximately 65 percent of nickel production is consumed by the stainless steel industry, with 12 percent of the remainder used in super alloys or nonferrous alloys. Nickel imparts corrosion resistance, temperature resistance and other benefits to its alloys (Table 1) (Oberg, 1996; Cáceres, 2003). The dominant types of nickel-bearing ores are classified as either laterites (limonite: nickel-iron oxide; and garnierite: nickel hydrosilicate) or magmatic sulfide deposits (pentlandite: iron-nickel sulfide) (U.S. Geological Survey, 2013a, 2013b). In 2012, about 40 percent of the nickel ore mined was sulfidic-type ores and about 60 percent was laterite. The processing of laterite ore is expected to continue to increase as the availability of sulfidic ores continues to decline."

Jan 1, 2015

This paper deals mainly with the modernization in the coal loading system at the loading piers of the Dominion Coal Company, Ltd., Sydney, Nova Scotia. The history of the operation is briefly outlined, and the construction of the Company&apos;s new pier is described in considerable de-tail. Particular attention is paid to the bins and conveyors, and to the loading tower. The paper concludes with a description of the S.S. Cape Breton Miner, built specifically for the coal trade, and the unloading facilities at Lakeview, Ontario. Coal Shipping at Sydney C OAL from the mines operated in Cape Breton by the Dominion Coal Company, Limited, has been shipped from the International Piers, situated on the east side of Sydney Harbour, for over sixty years. There were three piers, of which two were active-ly used in the shipping of coal until 1964. Nos. 2 and 3 were high piers about 600 feet long, of wooden construction throughout. They were founded on&apos; rock-filled cribs and creosoted piles driven into the harbour bottom, and each had two decks which carried standard-gauge railway tracks.

Jan 1, 1965

By Jurij Karlovšek, Marko Žibert, Scott Keniston

"SUMMARY The importance of information management was recognised in surface construction industry decades ago, and has increasingly being recognised through formal process and laws. Around the world, these laws and codes of practice are currently being drafted and enacted, to reflect the development of software tools and corresponding increasing adoption by industry. This paper deals with specifics of implementing information modelling in tunnelling business utilising BIM (Building Information Modelling) technology developed for buildings as well as similar technology developed for mining industry. Although BIM is recognized initially as a 3D digital representation of physical and functional characteristics of a facility, the real benefits come when complex capability through construction sequencing and even detailed programming (4D) and cost capabilities (5D) are included. INFORMATION MODELLING The Architecture, Engineering and Construction (AEC) industry requires the production of design and construction information, which involves the input from several teams. The tasks allocated to each team need to be carried out in a particular order and coordinated in order to benefit all those involved and the project itself; this is known as “collaborative working”. To ensure the quality, and guarantee that information can be used without change or interpretation, working processes and standards needs to be agreed upon or else it will hinder collaboration and have a negative impact on project delivery. Case studies show that the additional capital delivery costs due to uncoordinated, inaccurate and ambiguous information amounts to 20-25%. The solution to overcome these problems and improve collaborative working in a project is the adoption of BIM. It is a modern approach to the design, documentation, delivery, and life cycle management through the use of project information databases coupled with object-based parametric modelling. BIM requires traditional practices shifting from simple drafting to using 3D native models for building design environment. Additionally, it requires that models are equipped with information that has been traditionally decoupled in a text or other kinds of documents. The goal is not in creating a 3D graphic representation of design intent; rather, it is a comprehensive information management tool based on the simulation of design and construction build around a central repository."

Jan 1, 2016

By G. R. Hopkins

[Apparent progress in fuel economy at petroleum refineries, as measured by the average amount of .seat units required to refine a barrel of crude oil, received a set-back in 1935, when the average rose to 562,00 B. t. u., compared with 562,000 B.t.u. in 1937 (see fig. l). The primary factor in the rise in average heat requirement&apos;s per barrel of crude oil refined in 1938 wan the decline in total runs to Invariably the average requirement increases when crude ins to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries arc masked by the degree to which the capacity is utilized. Additional crude runs give lower average e heat requirements in two ways - first, because they are mane with the c expenditure of comparatively small amounts of auxiliary heat, and, second, because the additional runs generally represent simple topping operations. In 1938 crude runs, to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938 .]

Jan 1, 1939

By D. B. Smith

DURING the summer of 1953, test work commenced at the Sullivan Concentrator with a view to the modification of filtration practice by the inclusion of wet cyclone classification of the lead concentrates, with separate filtration of the underflow and overflow products. Formerly, practice was conventional and the equipment employed comprised one 50-foot diameter thickener ?with the underflow routed via a 20-foot stock tank to two 8-foot by 12-foot Oliver filters. Heating of the filter feeds to 40° C. and the use of mechanical slappers on the filter drums ?have both been standard features of Sullivan practice for years. Both of these have been retained. Currently (February, 1956), lead concentrates are being classified into sands and slimes by 12-inch cyclones with the underflow, at 75 per cent solids, being fed to No. 1 Oliver filter. The overflow is thickened to 75 per cent solids and filtered separately by a No. 2 Oliver filter . The tonnage split is approximately two of underflow to one of overflow. The overflow contains 75 to 80 per cent of the total minus I 500 mesh slimes in the feed.

Jan 1, 1956

"Some of the tools developed for the processing of nickel laterite ore by resin-in-pulp (RIP) may be applicable to the remediation of metalliferous mine drainage (MMD). In both cases, recovery of metal value and production of a stable waste stream appropriate for long term storage is desired. MMD typically has the additional challenge of management of toxic low-value metals. Seen in this light, innovations in RIP reactor configuration, selective elution strategies and novel synthetic ion exchange resins become useful tools for taking on the MMD challenge in a way that maximizes both environmental and economic benefit. INTRODUCTIONAcid mine drainage (AMD) is a common problem in any country with significant past mining activity. When sulphide containing minerals, tailings or slag are exposed to water, oxygen and sulphur oxidizing bacteria, AMD will result. Abundant and reactive iron sulphide minerals leach first, providing acidity and the ferrous/ferric couple that can enhance the oxidation kinetics of other minerals. If this runoff contacts encounters acid consuming carbonates or silicates, the acidity may be neutralized, but certain heavy metals remain in solution and can continue to be an environmental hazard (Gray, 1997). For this reason, the remainder of this paper will refer to the broader term metalliferous mine drainage (MMD) rather than acid mine drainage. In either case, such drainage, containing high heavy metal concentrations and often significant acidity, is toxic to aquatic life and can lead to significant damage to ecosystems and to public watercourses. MMD is a problem most commonly associated with now defunct sulphide mineral mines, but similarly toxic streams can result from many types of waste, such as poorly stabilized leach tailings, slag heaps, and coal flotation tailings (Johnson and Hallberg, 2005; Lee et al., 2002; Sainz et al., 2002; Schüring et al., 1997). In any case, the management and remediation of MMD is an important ongoing problem for the resource industry, particularly for the many mines in Canada closed before the advent of more stringent environmental standards. MMD remediation represents a significant long term expense for the resource industry. Multi-disciplinary efforts to understand and mitigate this problem range from creation of artificial wetlands (Poulin and Lawrence, 1996; Sheoran and Sheoran, 2006) to sophisticated biochemical reactors and precipitation processes (Hatami, 2010). Certain remediation technologies such as ion exchange offer methods to make a saleable product by recovering valuable dissolved metals. This paper will show how these technologies can help defray the cost of remediation, and offer potential to turn a dangerous waste stream into a useful product."

Jan 1, 2012

By W. Lin, M. J. McPherson

When a large area of open gob collapses suddenly, a windblast is produced that can cause considerable damage throughout the infrastructure of a mine. In a few cases, the windblast has been accompanied by ignitions of methane and/or coal dust. This paper describes the conduct and results of laboratory tests involving the compression of mixtures of air, methane and coal dust under a falling weight and while allowing controlled escape of the mixture. The transient responses on pressure and temperature sensors were recorded. In addition to an analysis of those records, the paper highlights those conditions in which ignitions occurred.

Feb 24, 1997

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By J. E. Dutrizac

"The end of an era in zinc metallurgy took place on July 31, 1976 when the horizontal retort furnaces of the National Zinc Company in Bartlesville, Oklahoma were permanently shut down (1) . For more than a century, horizontal retorting had been the most common method of producing zinc in the United States; it was a thriving industry in many parts of that country, especially in the natural gas belts of Oklahoma and Texas. With the Bartlesville closure, yet another metallurgical process has become an object of historical interest for North American metallurgists. Although shrouded in controversy, the origins of zinc metallurgy seem to date back at least 2000 years. Pyrometallurgical methods with carbon reductants are capable of producing zinc from oxidic zinc ores, but only above the boiling point of the metal. Although slow cooling results in re-oxidation of the zinc vapour by air or carbon monoxide, quenching yields liquid zinc; some form of rapid cooling, either accidental or intentional, was likely used by ancient metallurgists to liquify the metal. Zinc metal found in Athenian objects of the Roman era was likely of accidental origin. The Romans employed brass extensively for coins and ornaments(2) , and this was intentionally produced by the calamine process whereby oxidic zinc ores were added to molten copper under strongly reducing conditions. Zinc appears to have been known in China and India as early as 1000-1300 A.D., and was probably smelted commercially in those countries from the 14th century. Although the early metallurgical procedures were probably inefficient, they were able to produce zinc metal in significant amounts. The large heaps of zinc residues with clay retorts bear testimony to an early smelting industry of impressive magnitude. It is estimated that the heaps at Zawar, India alone represent the extraction of 100 000 tons of metallic zinc(2) In the 1730s the smelting of oxidic zinc ores was developed in England using a vertical retort method. In 1788 a British patent was granted for making zinc from zinc blends (ZnS) by roasting the ore in a coalfired reverberatory furnace, mixing the calcine with charcoal and smelting the mixture with suitable zinc condensation. The English process was very energy intensive, however, and early in the 19th century the Belgians developed a horizontal retort process for the reductiondistillation of zinc that was more fuel efficient. This technique was gradually developed into what came to be known as the Belgian process, the forerunner of the ""modern"" horizontal retort furnace."

Jan 1, 1999

By J. R. Parry

Over the past several years, computerized financial models have been an important part of Newmont&apos;s strategic planning process. Two applications will be discussed in this paper: a general purpose financial model of Newmont, and a detailed operational/financial model of Magma Copper Company. Newmont?s general purpose financial model was developed using Lotus 1-2-3. It was designed to aid management in assessing the financial consequences of investment and financing decisions associated with long-term strategic planning by simulating the consolidated effect from individual transactions. Not only is the model capable of assessing the sensitivity of specific decisions to changes in the external economic environment (i. e., commodity prices, interest rates, inflation and exchange rates), it can also evaluate the effect from operating and financial decisions, including changing production levels and cost structures at individual operating units as well as simulating several types of transactions, including equity and debt issues, acquisitions and divestitures. The analysis of Magma Copper Company required the development of a detailed operating and financial model of the Company. The model was developed using IFPS in the corporation?s UNISYS (then Burroughs) B7900 mainframe computer and included separate pro forma financial statements for each of San Manuel-Pinto Valley&apos;s mines and concentrators, as well as Magma&apos;s smelting and refining operations. The outcome of this analysis was the decision to merge Magma Copper and Pinto Valley Copper Corporation, and to recapitalize the new corporation in order to provide funds for a retrofit and expansion of its Arizona smelter and expansions of its refinery and SXEW facilities.

Jan 1, 1989

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The operation of intelligent coal mining in complex geological environment is still unable to realize automation. In order to realize the autonomous cutting of fully mechanized mining equipment and improve coal production, a mining and transportation equipment dynamic advancement path planning method based on spatial kinematics coordinate deduction prediction and real-time correction prediction of coal-rock state identification of equipment cutting current index are proposed. Firstly, the spatial motion law of the mining and transportation equipment is analyzed, and the mathematical model of the spatial motion of the mining and transportation equipment is established. The relationship between the adjustment of the shearer rocker arm and the pose change of the scraper conveyor is determined, and the coordinate deduction model of the spatial advancement position of the equipment is determined, which provides a theoretical basis for the advancement path planning of the mining and transportation equipment. Then, on the basis of the mathematical model construction, combined with real geological data and equipment information, the three-dimensional dynamic planning of the advancement path of the mining and transportation equipment is carried out from the two dimensions of the horizontal advancement direction and the shearer walking direction. At the same time, the relationship between the cutting current index of shearer and the state recognition of coal-rock mass is analyzed, and the coal-rock mass state identification of cutting current and the adjustment of rocker arm model is constructed, and the real-time dynamic correction of three-dimensional path is carried out, so that the planned path can better adapt to the sudden change of real geological environment. Then, using the unity3d virtual reality technology, a simulation system for the horizontal advancement path planning of the virtual mining and transportation equipment is constructed, which simulates the real advancement operation process of the mining and transportation equipment and conducts advancement training. Finally, the dynamic advancement scheme update prediction based on the existing actual cutting but ahead of the actual cutting is realized in the virtual scene, and the optimal scheme is transmitted into the existing prediction cutting system to guide the actual physical equipment mining. The path planning method can control the coordinate position error of the advancing cutting path within 15 mm, which provides ideas for the research on the advancing path planning of fully mechanized equipment.

Nov 22, 2022