Search Documents

By R. J. Enkin

Modern mineral exploration depends on multidisciplinary 3-dimensional integration of geological and geophysical data. Identification of the geological sources of geophysical anomalies requires knowledge of the physical properties fingerprint of rock types, formations and their alteration products. Understanding how and why rock physical properties vary within the Earth's subsurface ensures that appropriate geophysical exploration methods can be chosen, and allows for more efficient and effective surveys to be designed. Physical properties knowledge is integral to geophysical modeling - measured data or values estimated based on geological understanding are used to produce realistic forward calculations and to constrain inversion models. Mira Geoscience and the Geological Survey of Canada, in collaboration with industry and academia, are building a Rock Properties Database System (rpds.mirageoscience.com). It compiles the most valuable physical properties for mineral exploration (density, porosity, magnetic susceptibility and remanence, electrical resistivity and chargeability) linked with location and lithological metadata. A critical knowledge gap, addressed in this study, concerns the dependence of physical properties on alteration and mineralization processes. We report on the results of a collaborative University of British Columbia - Geoscience British Columbia project, ?Integrated Geological & Geophysical Porphyry Models: Adding Value to Geoscience BC Geophysical Data?. As part of the QUEST and QUEST-West geophysical initiatives, Geoscience BC focused detailed geophysical surveys on a suite of six known porphyry deposits: Mount Milligan, Endako, Huckleberry, Bell, Granisle, and Morrison. Physical properties for a set of 269 samples of characteristic host rocks and their altered equivalents were measured. The causes of physical properties variations were investigated through their correlations with ore and alteration mineralogy determined from thin-section observations and X-ray diffraction analyses. Physical properties of variably altered host-rocks and intrusive rocks vary significantly between different BC porphyry deposits. No specific unifying geophysical model exists that can be uniformly applied during exploration. Knowledge of local background geology and local physical properties variations is necessary as host-rocks and intrusive rock compositions vary depending on magmatic affinities, and alteration styles will vary reflecting host-rock compositions, crustal depth and influence of meteoric water. A district-scale exploration strategy requires location of intrusive bodies, which are commonly magnetic, resistive and low in density. Correlations should not be expected between density and magnetic susceptibility, because alteration may lead to magnetite destruction or to secondary magnetite development. Deposit-scale ground geophysics might image potassic alteration zones that can be magnetic in both alkalic and calcalkalic systems. Low magnetic susceptibilities, resistivities and densities might aid in locating the typically more porous phyllic and argillic zones. All geophysical data must be interpreted with background knowledge of local rock types and in light of the expected deposit model and associated magmatic and hydrothermal processes. The most effective means to building physical properties knowledge prior to geophysical investigation remains collecting rock physical properties measurements. The cost of rock properties data collection is low, relative to the overall costs of running a mineral exploration program, and can provide an important framework for design of geophysical surveys, survey method selection, geophysical modelling, and data interpretation.

Aug 1, 2013

By J. C. Bokros, A. S. Schwartz

The irradiation-induced densification of pyrolytic carbon has been shown to take place by a simple first-order rate process. The values of the densification constant, kd, for isotropic carbons are 1.0 x 10-22, 1.4 X 10-22 and 2.8 X 10-22 (nut)-1 at irradiation temperatures of 520o, 670°, and 1000oC, respectively. The apparent activation energy obtained from the temperature dependence of kd for isotropic carbons is about 0.2 ev. Estimates of the maximum stresses that develop in isotropic carbons owing to shrinkage onto an unyielding support show that stresses in excess of 15,000 psi may be avoided during irradiatian at 600" and 1000°C if the initial coating density is kept above 1.5 and 1.9 g per cu cw, respectively. If a carbon coating on an unyielding support is not completely isotropic, stresses may continue to build up at high neutron exposures after densification is complete because of continued anisotropic distortion. Stresses in excess of 15,000 psi from this source may be avoided during irradiation at 1000°C if' the Bacon anisotropy factor is kept below 1.3. A variety of applications of carbon and graphite in nuclear technology has stimulated numerous studies of the effect of neutron irradiation on these materials One of the most interesting problems associated with the use of carbons and graphites in the high fast neutron fluxes of nuclear reactors arises as a consequence of the neutron-induced dimensional changes that occur during irradiation. Energetic neutrons displace car- bon atoms from their lattice positions; and, depending on the temperature, the interstitials and vacancies produced migrate to form clusters, recombine, or are annihilated at dislocations or crystallite boundaries. The competition of various sinks for the point defects results in structure-sensitive bulk-dimensional changes that vary with temperature in a complicated way. This paper deals with the neutron-induced dimensional changes in turbostratic carbons that are being used as coatings on nuclear fuel particles. Details of the structure of these carbons and the variations of their structure with deposition conditions have been reported.'-3 It has been shown in previous work that the neutron-

Jan 1, 1968

By J. C. M. De Souza

The Samarco pipeline, the longest in the world for iron ore slurry transportation, started operation in 1977 to transport concentrate from the Germano facilities, in the state of Minas Gerais, to the pelletizing plant, located 396 km away, in the state of Espirito Santo, on the south-east coast of Brazil. Designed for a nominal capacity of 12 million tons per year, the pipeline reached 15.5 million/year due to operational improvement and, in late 2005, it was resized to transport 16.5 million tons per year, with the installation of a booster station. In order to ensure the accurate performance of the system, a pipeline cleaning programme was carried out and, since it has been29 years from the operation start-up, precise knowledge of the pipe condition would be fundamental to guarantee the success of the project. The cleaning programme demonstrated the potential of operational gains from this initiative, and its effect on the corrosion control and future measures, which should be permanently adopted to maintain the improved capacity. The intelligent pig runs provided essential data used to establish a pipeline integrity programme that allowed Samarco to develop a pipe repair plan based on the severity and significance of the features and to implement a future pipe replacement plan.

Jan 1, 2007

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By R. V. Lundquist

The specific conductance of solutions of sodium hydroxide and of sodium aluminate was directly proportional to the temperature. The specific conductance of sodium aluminate solutions with identical sodium ion concentration and at constant temperature decreased with increase in aluminum concentration. The aluminate ion population in solution was shown to consist of a mixture of monovalent and polyvalent ions. Aluminate ions did not influence the temperature dependence of pH in caustic solutions containing sodium aluminate. The density and viscosity of a solution was inversely proportional to the temperature and directly proportional to the concentrations of sodium and aluminate ions.

Jan 1, 1965

By C. Liliane Carvalho

In the current study, bio-oxidation tests were carried out in shaking flasks with a flotation concentrate containing the sulphides pyrite, arsenopyrite and gudmidite. The tests were performed with mesophilic microorganisms (At. ferrooxidans) at 30 °C and also with the moderate thermophile S. thermosulfidooxidans, at 50 °C. The effects of (i) previous adaptation of the microorganisms to the concentrate, (ii) ferrous iron concentration and (iii) pulp density (2%, 4% and 6% (w/v)) on the dissolution of the sulphide were studied through arsenic extractions. S. thermosulfidooxidans was more sensitive to the pulp density in comparison to At. ferrooxidans as a reduction in sulphide oxidation was observed with the increase in the solid content to 6%. Therefore, the mesophilic strain was selected for further work, which comprised a rolling bottle experiment at 10% solids. After 40 days of bio-oxidation, the solid material was subjected to cyanidation, which revealed 85% gold extraction as compared to 21% from the original concentrate. The antimony sulphide grains in the bio-oxidized product showed similarity to what was observed in the original sample, suggesting such particles were not susceptible to the bio-oxidation process.

By T. P. R. de Jong, H. Harbeck

"This contribution reports recent mineral sorting experience and lists the opportunities of the newest generation of automatic sorters with a special focus on electromagnetic detection and Xray transmission. With the available sensor resolutions and actuator systems that are available today sorting of minerals down to 2 mm size and up to 250 mm lump size is technically feasible. In industry, ore as well as coal is still hand-picked and current automation potential only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs.They are:??High speed and high resolution sorting systems based on X-ray transmission imaging??High speed on-line image processing and further development of advanced data processing??Modular multi-sensor automatic sorting units (using one or more sensors such as colour, electromagnetic and X-ray in a single device)??Sensitive electromagnetic sensors for sorting based on differences in magnetic susceptibility and electric conductivityThe above enables compact dry separation, insensitive for moisture fluctuations and at high separation sharpness, as well as “electronic” high gradient magnetic separation for larger particles. Besides conventional X-ray transmission (XRT), dual-energy XRT (DE-XRT) is now being redesigned to meet the requirements of the mining industry. The mentioned technologies provide automatic dry separation of minerals and rock as alternative for conventional processing."

Jan 1, 2005

By R. J. Fruehan

Oxygen steelmaking (OSM) is not only the dominant steelmaking process but defines the structure of the industry. There are a number of myths regarding the future of OSM, which are false. These myths include that the EAF will become the dominant process in the near future, it is less costly to produce steel in an EAF and OSM is a mature technology and no new developments are occurring. These myths are shown to be false. Selected new developments are discussed such as post combustion, recycling of waste oxides, slag splashing and sensors.

Jan 1, 2004

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By G. H. Agnew

When water floods are initiated after gas-oil ratios have increased, the transition period from the start of injection until" the gas-oil ratios are returned to the solution gas-oil ratio may be important for either economic or technical reasons. The transition period is longest, and consequently most critical in water floods where injection is equal to withdrawals. This paper describes a theoretical basis for predicting the behavior of such a system and outlines a procedure for making the necessary calculations. The calculation procedure is illustrated for two actual cases: a line drive water flood and a five spot water flood. In each case there is a reasonable similarity between the actual and calculated performance.

Jan 1, 1960

By George J. Conroy

Electrical power generation was studied in a laboratory-scale, open-cycle vortex MHD generator, which offers several advantages over straight-channel generators that require separate combustors. Compactness, lower capital cost, and high-energy release are obtained by combining the combustor and generator into one unit in the vortex generator. In addition, the vortex generator uses a simple solenoid rather than the more complex and expensive saddle magnet required for straight channel generators. Although the vortex generator must utilize combustion gases with a low Hall coefficient in order to be efficient in direct comparison to the linear generator, the primary motivation for this experimental device in terms of ultimate objective was to investigate the vortex generator with applications to direct coal firing and with combustion taking place in specially designed expansion nozzles. The vortex device offers one decided advantage over the linear device in this regard because slag deposits do not degrade or short-circuit the coaxial electrodes as is the case for a linear machine. The experimental vortex generator consists of a modified cyclone burner 7 ½ in ID by 21 in long, with the inner wall used as one electrode together with a coaxial center electrode. Power was obtained by impressing an axial field of 3,000 G from an air core solenoid magnet. Tests were conducted by seeding natural gas seeded with potassium acetate and burning with preheated oxygen-enriched air. Power generation was lower than calculated because theoretical plasma velocities were not achieved.

Jan 1, 1972

By M. R. Smith

Barrick Goldstrike Inc.'s Betze/Post Open Pit is located at the north end of the Carlin Trend, in Eureka County, Nevada, U.S.A. (see location Map, Figure 1). About ten open pit gold mines exist on the trend, which strikes northwesterly, through the north end of Eureka County and into Elko County. The final Betze/Post Pit configuration is shown in Figure 2, Pit Configuration. The final pit will be about 2450m long by 1550m wide, elongate in a west-northwesterly direction. The pit straddles the Barrick/Newmont property boundary. The highest elevation of the pit perimeter is 1800m at the south wall, with the east end pit bottom elevation at 1200m.

Jan 1, 1993

As part of the Australian Mineral Industries Research Association (AMIRA) P9 project, methods of characterising both the ore and the machines in flotation circuits have matured considerably over the past 15 years. Machine characteristics include gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity. Ores can be characterised in terms of floatability parameters on a size and mineral basis. Measurements have been performed on various copper plants in many countries around the world over the last 5 years. This paper outlines the cell and ore floatability characteristics of each copper plant and provides a discussion on the differences between these plants. In general, most porphyry copper ore bodies are processed at high tonnage through several parallel banks of cells at each stage of flotation. The floatability parameters of these copper ores are very similar in terms of rate of flotation and proportion of fast, slow and non-floating material. The cell characteristics are also similar, with superficial gas velocity, bubble sizes, and gas hold-up values being of similar magnitude. Investigation of the similarities and differences of the modem copper flotation circuits has allowed an increase in understanding of the particularities of copper flotation. Comparison against other copper circuits provides a benchmark and opportunities for future optimisation.

Jan 1, 2007

By Lynn L. Rethi

This U.S. Bureau of Mines report summarizes common obstacles found when attempting to implement health and safety strategies in small mines and small businesses in general industry. Recently, the U.S. Mine Safety and Health Administration focused much of its attention on addressing health and safety issues at small mines. Some of the more innovative interventions practiced by small businesses in general industry are discussed for consideration of their applicability to the mining industry. The most effective intervention strategy that was developed for small businesses is the Occupational Safety and Health Administration Consultative Program. The details of this program and other intervention strategies used by small mines and small businesses are presented.

Jan 1, 1995

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By Leopoldo Mariscal

El presente trabajo describe los aspectos más importantes del proyecto de Fundición de Ilo como son: la tecnología, el desarrollo de la ingeniería y construcción, el impacto económico, social, tecnológico y ambiental de su ejecución y los planes de entrenamiento y comisionado de la nueva planta. Asimismo considera entre los equipos principales: un horno de fusión en baño ISASMELT asociado a un caldero de recuperación de calor y un precipitador electroestático, cuatro convertidores Peirce Smith, dos electroprecipitadores, dos plantas de ácido, dos plantas de oxigeno, dos plantas de efluentes, una planta de moldeo de ánodos, dos hornos de limpieza de escoria, y varias plantas auxiliares más.

Sep 12, 2005

By J. Huh

Recently, there is growing trend to build the high-rise and install curtain walls. Following this trend, we developed robot for building wall cleaning work, which moves along Built-in guide rail of building. Because it moves attached at building wall for cleaning work, it can be seriously affected by potential threats, like earthquake, strong wind, malfunction, and construction error of built-in guide rail. In order to cope with those threats actively, this paper presents the Fail-Safety system. The building wall cleaning robot consists of two moving system: The Horizontal Moving System which mainly do maintenance work, and The Vertical Climbing System which transport the horizontal moving system floor by floor. We apply the Fail-Safety system to these systems. The Fail-Safety system consists of sensors to detect external situation, and, with information of sensors, give instruction for what to do. This robot system is installed with four kinds of sensors: shock sensor, infrared ray sensor, laser sensor, magnetic sensor. First, shock sensor detects external shock during cleaning work. When shock sensor detects big shock, the robot returns to starting point to inspect how damaged it is. Second, infrared ray sensor detects damage of built-in guide rail. It is to prevent destruction of robot caused by moving along damaged rail. Third, laser sensor gives notice about where obstacle is. It is for robot to avoid crash with obstacle and decrease damage. Fourth, magnetic sensor detects magnetic points, which are installed in rail at regular intervals, and helps robot to find its position, based on location of magnetic points detected. If robot is damaged by external shock and its encoder, which gives information of location to it, is not working, magnetic sensor will give information of robot?s location to robot. And then, robot regulates its velocity depending on position of it, and safely returns to starting point. The Fail-Safety system in this paper is for building wall cleaning robot to sense external threats, and prevent getting worse. Applied to this active protection system, making safe environment of maintenance work is possible for robot system.

Aug 1, 2013

By Jeff LeBlanc, George Gutierrez, Carl Pitzer

The Bay Park Conveyance Project was one of the largest microtunneling and rehab projects in the United States at the time of completion. The completed project conveys treated water from the South Shore Water Reclamation Facility located in Nassau County, New York, which currently discharges an average of 50 million gallons per day (MGD) of treated water into Reynolds Channel, to the Cedar Creek Water Pollution Control Plant (WPCP) ocean outfall pipe. The pipe carrying treated wastewater was installed approximately 20–60 feet below the surface. The treated wastewater is conveyed via microtunnel construction of a 2-mile long force main from the South Shore Water Reclamation Facility to an existing aqueduct under the Sunrise Highway, the rehabilitation of an 7.3-mile stretch of the aqueduct via sliplining, and construction via microtunnel of a 1.6-mile-long force main to connect the rehabilitated aqueduct to the existing Cedar Creek Water Pollution Control Plant (WPCP) outfall, which discharges and diffuses treated water three miles offshore in the Atlantic Ocean. This paper will review the Design-Build requirements, the chosen innovative solutions during planning for the micro tunneling portion of the project and review the microtunnel construction on the project.

Jun 23, 2024

By Stanley M. Walker

Safety consciousness is not a constant for which a specific value can be assigned, but is a variable, which is frequently intangible. Its evaluation is not simple. We all know that safety consciousness is the most potent factor in the prevention of accidents. Safety consciousness may be defined as awareness of hazard and alertness to danger, which controls every action of an individual through his desire to remain alive and uninjured.

Jan 1, 1951

By H. H. Waller, D. L. Monroe, D. P. R. Smyth

ORIGINALLY slusher drift development was conventional, advancing the drift full 10x13-ft size at 6 ft per round. This proved dangerous and costly because the weak fractured rock of the orebody cannot be left raw for any length of time without its reacting with air to cause spalling. With this method of drift development ground conditions were worsened by many blasts and the length of time it was necessary for the drift to remain open. The problem was practically solved by driving 5x7-ft pilot drifts, then enlarging to 10x13-ft raw size by slashing with 50 to 60-ft diamond drill holes. Calculated explosive charges are used to avoid wall and roof shattering. Still more recently jacklegs and sectional steel replaced the diamond drills, resulting in the same work for less than half the cost, see Figs. 1 and 2. Crosscuts at right angles to the main haulage drifts, which cross through the center of the ore-body, divide the ore into 200-ft blocks. Eight slusher drifts on 50-ft centers draw from one block. The slusher floor is 11 ft above the rail, inclined at 1 pct grade, and the top is 18 ft below the undercut. The finished slusher drift is 102.5 or 120 ft long, depending on whether it is north or south of the crosscut. Drawpoints are staggered on each side at 17.5-ft centers. The completed drift is concreted and has an inclined ramp and a vent at the back. When crosscuts and gangways have been excavated and concreted and slusher stations installed, slusher drift development is carried out in 10 clear-cut stages: 1—Pilot drift is driven full length, 5x7 ft. 2—Station is excavated at half-way point in pilot drift. 3—Pilot drift is enlarged to slusher drift size by drilling. 4—Lower part of slash is blasted and mucked for floor concrete. 5—Floor is poured. 6—Inside upper half of slusher drift is blasted, mucked, and concreted. 7—Outside upper half of slusher drift is blasted, mucked, and concreted. 8—Drawpoints are excavated. 9—Drawpoints are concreted. 10—Concrete ramp and sheave protection recess are constructed at back end of slusher drift. A 5x7-ft pilot drift is driven full length on the center line of the proposed slusher drift using a jackleg and detachable bits on 7/8-in. hexagon steel. A 10-hp air-driven slusher and 36-in. scraper pull muck directly into cars in the main haulage crosscut, see Fig. 2. Operations are on a three-shift basis. One man mucks the previous round, drills, and blasts his round in a shift. Average advance is 5 ft per shift. When the pilot drift is completed, 7 ft of drift in the center section is enlarged to full raw slusher drift size of 10x13 ft, for the set-up to drill long slash holes. The pilot drift is slashed to full raw size from this station with jacklegs and tungsten carbide chisel bits on 7/8-in. sectional steel. Crews line the holes without trouble, working from controls established by the engineers, and the pattern of holes for the slash is arranged to give the least shattering effect

Jan 1, 1955