Search Documents

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By M. B. Dusseault, A. Pirayehgar

"There is concern that hydraulic fracturing (HF) near an existing critically stressed fault could trigger slip and generate a seismic event of significance. To this end, a mathematical discontinuum model representing a naturally fractured rock (NFR) mass containing a fault is created, and fault slip response to fluid injection is studied. UDECTM is used as a Discrete Element Method (DEM) approach to define the seismic moment, and also to assess the influence of injection and slip on further shear slip propagation. In most of the simulations, slip and dilation take place along a number of oriented fracture surfaces, so it is reasonable to assume that in a real case, microseimic emissions would accompany each slip “event”. The moment magnitude scale (Mw) is used to measure the size of the microseismic event in terms of the energy released. Seismic moment is a measure of the total energy (work) released during a seismic event and is used to measure its size. From another aspect, the injection energy is calculated as the total energy required for achieving the hydraulic fracturing; this is viewed as energy to open fractures against the ambient stress field and much of it is potential stored energy that can be released and create discontinuities (work of fracture), deformations (W=F·d), heat and radiated seismic energy. A small amount of the total released energy is transformed to radiated seismic energy and another small amount results in tensile fractures. Fracture energy is used to calculate the work required to create fracture surfaces. Comparing the energy release by fracturing or seismic events indicates their contribution to the total amount of released energy or total work. The amount of energy associated with the stick-slip event is small compared with the overall work done to generate the distortions (i.e. increases in aperture by forcing them open) in the rock mass, and much of the energy in slip is lost as heat from the plastic deformation, rather than as radiated seismic energy.Microseismic monitoring shows the spatial distribution and magnitude of seismicity associated with slip of bedding planes and natural and incipient fractures. Work calculations have been undertaken to look at the various sources of energy storage (elastic strain energy) or dissipation (slip), and likely the energy losses from viscous dissipation could be addressed as well, helping to clarify HF processes in NFRs."

Jan 1, 2015

By Morris Muskat

ALTHOUGH the problem of well spacing is one of the most important involved in the production of oil, it must be considered at the present time as still subject to further development. The published literature on this question is so voluminous that we cannot enter here into a review of it, except to refer to the recent papers by L. L. Foley1 and E. A. Stephen-son,2 where other references are cited. However, a decisive and conclu-sive answer to the problem of well spacing in any general form does not seem to have been developed. And while we shall be unable to present the desired solution in the present paper, it is nevertheless felt that the material to be given here not only provides the physical ground work for the ultimate solution, but shows qualitatively the essential factors that enter the well-spacing problem. Field studies of the well-spacing problem, in which the ultimate recoveries from different fields with different well spacings have been compared, have generally suffered from the lack of knowledge as to the similarity of the inherent characteristics of the producing reservoirs being compared, such as the sand volumes, the sand porosities, the sand permeabilities, the original reservoir pressures, the presence or absence of gas caps, the presence or absence of effective water drives, and the economic limits of production rates at which the various fields were considered to have yielded their ultimate recoveries. Certainly no one who is evaluating originally the economic significance of any oil reservoir would deliberately ignore these phases of the problem. And it is equally certain that no one would reasonably expect the ultimate recoveries from two reservoirs, even with the same well spacing, to be identical regardless of these other factors. More reliable results might be expected from comparisons of the recoveries obtained from different leases with different well spacings, but producing from the same reservoir sand. Unfortunately, however, even conclusions for such studies may be subject to serious errors. The reason simply is that however much one may insist that an operator is entitled only to the oil immediately underneath his surface acreage he will nevertheless drain the surrounding properties as long as his reservoir

Jan 1, 1939

By E. B. Wright

THE property of Falconbridge Nickel Mines, Limited, is in Falconbridge township, approximately thirteen miles northwest of Sudbury. From the mine and townsite, a gravel road leads to Sudbury and a branch line of the Canadian National railway to Sudbury Junction. The ore deposit is at the southeastern corner of the 'Sudbury Basin'. It lies in a sheet-like mass, striking in an east-west direction, between norite to the north and greenstone to the south. The general attitude of the ore-body is vertical, but with frequent variations in dip of as much as 10° to the north or south. The deposit is very irregular in outline, the width varying from a few feet to eighty or ninety feet. In the vertical plane, rolls are frequently encountered. Gouge is very often present at one or both ore contacts. The norite to the north shows much jointing. The chief ore minerals are pyrrhotite, pentlandite, and chalcopyrite. The nickel content of the ore is usually double the copper content, average assays ranging from 2 to 2.5 per cent nickel and 1 to 1.5 per cent copper. The ore is of three main types: massive, breccia, and disseminated. The breccia ore, the most common type, consists of sulphides containing rounded inclusions of highly-altered country rock, which, in places, are so large that sorting is necessary in the stopes. In the norite, the breccia ore may grade into disseminated sulphides, which frequently are sufficiently concentrated for profitable mining. In places in the breccia ore, concentrations of solid sulphide masses occur. Until early in 1935, all mining at Falconbridge was by shrinkage scoping, but this method was found to be less and less suitable as greater depth was attained. When mining had reached the 1,000-foot level, ore drawn from large shrinkage stopes was found to have been diluted as much as fifty per cent by sloughing of the wall-rocks, caused by increased rock pressure and insufficient support. It was apparent that this method of stoping was un-suitable and -Mr. E. J. Martin was engaged to superintend the introduction of a method of cut-and-fill stoping.

Jan 1, 1938

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981

By D. Hodouin

The optimisation of mineral processing plants requires the evaluation of performance indices such as production rate, product quality, valuable mineral recovery and process efficiency. Decision to change operating conditions or equipment to improve plant performances rely on the significancy of the estimated performance indices. The better is the quality of the estimation, the better is the discrimination capability of the index and as a consequence the larger is the operation improvement. The reliability of performance calculation depends on the sensors nature, accuracy and location, on the data redundancy, on the correction method applied to raw data and finally on the propagation of measurement errors along the calculation of performance indices. To maximize the quality of the data collected for performance evaluation, the following techniques are presented, discussed and illustrated: redundancy and observability analysis, data filtering for mass conservation, variance analysis of performance calculation, and data acquisition strategy design.

Jan 1, 1991

By Charles R. Barnhart

The Nitrogen Dioxide Cloud: After one year of testing it can be stated that we do know and understand a great deal about why the nitrogen dioxide formation is exacerbated in cast blasting. Picture 1 is an example of how concentrated the NOx can be from a cast blast. It has long been felt that 300 or more milliseconds of timing needs to be put between each row of detonations to allow the rock a maximum time of flight so the cast percentage is high. Our experiments have found that higher cast percentages can make with timing between 150 to 200 milliseconds between rows. Picture 2 show a definite improvement in nitrogen dioxide concentration and most of that was the result of shooting a previously shot end of the cast pattern that had not been dug, thus no confinement of the powder columns.

Jan 1, 2004

By G. Hu, P. Chang

"As hydraulic fracturing is forbidden in some countries due to its accompanying environmental pollutions, microwave fracturing was proposed as a substitute technology to enhance coal seam permeability. Its mechanism includes: on the one hand, thermal stress caused by non-uniform microwave heating leads to fracture development in coal body, which increases coal seam permeability for gas; on the other hand, moisture within the coal body that hinders gas desorption and diffusion is removed during this process. To study the effect of moisture content on fracture development under microwave irradiation, high resolution photographs were taken before and after microwave treatment. These photographs were then binarized and skeletonized. Based on the processed photographs, the total area were calculated using ImageJ. The results showed that coal samples with 0% and 25% water saturation have more variation in fracture development as compared to that of samples with 50%, 75% and 100% water saturation. This study can be very useful in gas drainage and gas control in coal mines. INTRODUCTION Coalbed methane (CBM) is a clean energy source as well as a natural hazard to underground mining (Kurnia, Sasmito, & Mujumdar, 2014; Ranathunga, Perera, & Ranjith, 2014). One of the main goals of mine ventilation is diluting methane and removing underground contaminants (Xu, Huang, Nie, Chalmers, & Yang, 2017). Coalbed methane (CBM) has to be extracted prior and during underground mining to avoid methane outburst and explosion accidents. However, with the increase of mining depth, the coal permeability decreases significantly, which makes it hard to extract the methane (Huang, Xu, Hu, Kizil, & Chen, 2018). To enhance the coal seam permeability, many CBM recovery methods have been applied on-site, such as hydraulic fracturing and enhanced coalbed methane (ECBM). However, hydraulic fracturing is restricted due to environmental concerns and ECBM is only suitable for the coal seam with relative large permeability (Bustin, Bustin, Chikatamarla, Downey, & Mansoori, 2016; Huang, Xu, Chen, & Chen, 2018; Huang, Xu, Hu, et al., 2018)."

Jan 1, 2019

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

By Marcus M. Key

Silicosis among metal miners is an ancient disease, probably as old as mining itself.' However, the primitive forms of mining were not productive of much silica dust, and the short life span of slaves used in mining probably precluded the development of more than a few sporadic cases of silicosis. Early diagnostic terms of miners' asthma and miners' phthisis suggested an occupational relationship and a tubercular component, but little attention was given to silicbsis until the turn of this century when epidemics of silico-tuberculosis arose due to the great expansion of the mining industry in the United States, especially silver and gold mining. The expansion was accompanied by mechanization and the introduction of pneumatic tools, which generated increasing amounts of fine silica dust. Mining communities were crowded and hygiene was poor.' The tubercle bacillus would probably have flourished even without the predisposition of silicosis.' As is so often the case in occupational health, biostatistical analyses first called attention to the problem, and environmental-medical studies later confirmed its existence. The bio-statistical analyses were occupational mortality statistics compiled by the Prudential Life Insurance Company in 1907, showing evidence of excessive mortality from tuberculosis and relationship to dust exposure. I The

Jan 1, 1971

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

The Aberfoyle Tin Mine lies on a wide sloping bench about 2,000-2,500 ft. above sea level, at Rossarden, 14 miles north of Avoca, in north-eastern Tasmania. The quartz-cassiterite veins were discovered in 1916, but mining did not begin until 1926. Trenching revealed seven small tin-bearing veins within a width of 57 ft. of Palaeozoic slates and sandstones, and it was assumed that the mineralization extended beneath the adjacent cover of Permian strata, but the presence of the main vein system (the 26 Vein System) was not suspected until the Aberfoyle Fault was discovered late in 1928.The mine has now been developed on thirteen levels, to a depth of 1,350 ft. The lower limit of economic mineralization appears to lie at about the ll-level, which is 1,060 ft. vertically below the concealed outcrop of the main veins. Production of tin and tungsten concentrates began in 1932, and to date more than 550,000 tons of ore have been mined for a recovery of 8,856 tons of tin concentrates, and 3,056 tons of wolfram concentrates, valued at approximately £6,500,000.This paper reports part of an investigation undertaken by the Mineragraphic Investigations Section of C.S.I.R.O. to study the mineral composition of the ore in relation to the apparent failure of cassiterite and wolfram mineralization to extend below the present working limits of the mine, and was first issued as Mineragrapnic Report No. 639.GENERAL GEOLOGY:The deposit consists of a series of quartz veins in a northsouth trending sheeted zone, transecting folded slates and...

Jan 1, 1957

By Hans W. Schreiber

INTRODUCTION At the end of the day, the decision by the sponsor to proceed with a project and to seek financing, or the decision by the financier to grant financing are made on a judgmental basis. Cash flow projections, sensitivity and risk analysis, the innumerable ratios applied by the financier, the so-called feasibility study, etc. are all only tools, and the degree to which they affect decisions is as highly varied as are the personality differences and business conduct and outlooks of the persons who render the decision of "go or no-go". The independent consultant, then, is expected to provide an additional increment of credulity and/or reliability to the "tools" which others will use in reaching a decision; the consultant is really not in a position to directly recommend a "go or no-go". PROJECT FINANCE INGREDIENTS The project finance situation has basically three ingredients: - The project; - The inherent risks attendant with project failure; - The parties. The project, to be viable for financing, will have certain essential characteristics, namely: 1. Clear title or rights to the mineral; 2. Proven definition/establishment of mineral quantity; 3. Financial viability; 4. Physical access consistent with financial viability; 5. A market for the product at a price and for the quantity consistent with financial viability; 6. Transportation/shipping from the project facility to the market at a cost consistent with financial viability; 7. Availability and demonstrated expertise of the developer of the facility; 8. Demonstrated expertise of the operator of the facility; 9. Production processes do not involve unproven new technology; 10. Availability of management personnel; 11. The property and the facilities have value (and thus can be used as collateral); 12. Government approvals/support, as required, will have been obtained; 13. The political environment is essentially friendly and stable; 14. The owner(s) of the project have the financial, strength to make equity contributions consistent with total required investment capital and project risk; 15. Backing by credit support other than that of the financier (i.e. guarantees); The inherent risks of failure are (Nevitt, 2nd Edition); 1. Completion delays with consequent delays in the generation of revenue 2. Cost overruns 3. Technical failure 4. Financial failure of contractors 5. Government interference 6. Uninsured losses 7. Increased price or shortages of raw materials, supplies 8. Technical obsolescence 9. Loss of competitive position in the market place 10. Expropriation 11. Inadequate/poor management The parties directly or indirectly integral to the project financing are: - The mineral rights owner - The developer - The operator - The equity investor

Jan 1, 1985

By John J. Dran

Large mining companies use a number of sophisticated analytical techniques for introducing the element of risk into the valuation of mineral reserve sites. These methods include, but are not limited to, sensitivity analysis, computer simulation, conditional probability, and portfolio theory. Such techniques enable the managements of these large companies to have an awareness of the many possible ramifications of their investment decisions. On the other hand, small mining companies and individuals in the mining business, due to limited financial and technical resources, still rely primarily on single point estimates of the value of mineral reserves. These small miners introduce the aspect of risk only through the application of an appropriate "speculative" discount rate. This paper illustrates the application of a technique for the introduction of risk into investment analysis. The method appears to be most suitable for use by small mining companies and individuals contemplating a large investment in a new mineral reserve site.

Jan 1, 1974

By Frank E. Cash

As a part of its safety program the United States Bureau of Mines has fostered the development, use, and improvement of portable electric mine lamps. Although there is still need for better illumination in mines and the replacement of open lights has been slow, improvement in electric cap lamps and increase in their use indicate one phase of recent progress toward safer and more efficient mining This report is the result of a recent survey of electric-lamp installations in the Alabama mining; district; it shows the misuse, increase in use, and relation to certain classes of accidents of these installations.

Jan 1, 1935

By J. T. Ryan

SiR Humphry Davy's epoch-making treatise delivered on Nov. 9, 1815, before the Philosophical Society of London, first announced and demonstrated a flame safety lamp for detecting methane in mine air. Coal mining was known in England as early as 1180, more than 600 years before the advent of a safe lighting and gas-detecting appliance. Mining, no doubt, took place first in outcrop coal, and danger from gas did not become apparent until the workings became deeper and more extensive. Davy's lamp did much to increase the safety of miners, and a modified Davy lamp is still widely used for detecting the presence and approximate amount of combustible gas in mine air. No factor in coal mining has improved more rapidly during the past 15 years than safety measures. This progress came about not only as a result of the workmen's compensation laws now in force in most of the states of the Union, but because the research work of the U. S. Bureau of Mines had demonstrated some dangers incident to coal mining which were not considered to be serious matters prior to that time. Electric power and explosives are necessary but potential hazards in American coal mines. A general mechanization program is now under way, while the mines are growing deeper and more extensive. Consequently ventilation problems are more complex and a demand has been created for positive detecting devices for carbon monoxide as well as methane. Scientists and manufacturers, working hand in hand during the past 10 years, have invented and developed appliances which make systematic and effective examination of mine air possible. The object of this paper is to describe briefly the approved testing devices in use today, with the hope that they may lead to the saving of life. Two Groups of Dangerous Coal Mine Gases Dangerous coal mine gases may be placed in two groups: (I) those that are dangerous because of their explosive properties, and (2) those that are dangerous because of their toxic properties. Methane (CH4) is the important gas of the first group, and in so-called gaseous mines constantly exudes from the coal and rock; it may accumulate and form an explosive mixture. The explosive range of methane-air mixtures is well defined. The low limit is 5 per cent., the high limit 15 per cent., and the most explosive

Jan 1, 1927

By Albert L. Toenges

COAL mining technique progressed slowly until the advent of mechanized mining. The cutting machine was a forward step, but had only a limited effect upon improving the percentage of coal recovery. Previously, the physical fitness of the loaders and the total output of the miners fixed mine production. The miner was an independent contractor and supervision over his working place was superficial. Rising costs and the inroads of substitute fuels demanded increased output per man to lower the unit production cost. Therefore, the amount of coal loaded mechanically in underground bituminous mines has risen from 0.3 per-cent in 1923 to 7.4 in 1929, to 20.2 in 1937, and to 48.9 percent in 1943. When loading devices were introduced it became necessary to adapt them to existing systems of mining, or to alter the mining system to fit the machine. An increased amount of supervision was required as output depended upon proper operation of the machine rather than on the physical fitness of the individual.

Jan 1, 1946

By M. Tangstad, B. Monsen, H. Midtgaard, R. Ishak, M. Syvertsen, I. Solheim

Charcoal is an interesting reducing agent because it is produced from growing wood which is renewable and does not contribute to global warming, provided that there is a balance between the felling of timber and growth of trees. In the biocarbon project the possibilities for using charcoal is investigated as well as other biological based and renewable reductants for ferroalloy production. The background for the project is that the Norwegian ferroalloy producers wish to contribute to reduction of CO2- emissions. This paper focuses on the use of charcoal instead of coke for the production of manganese alloys, and the consequences of doing so. Results from practical SiMn smelting experiments on a pilot scale have previously been reported, where only 12-14 % Si in the metal was obtained when charcoal was used. Recently we have attained satisfactory 18 %Si also for charcoal, but good results are indeed dependant on good furnace performance. There is no tradition for using charcoal for manganese production in Norway. A change from using mainly coke to the use of some charcoal will demand new routines for furnace operation, raw material and off-gas handling. Hence, characteristic properties of charcoal, which may cause change of furnace operation, have been measured and are compared to coke. The following results are presented: ?Thermal abrasion strength together with CO2- reactivity; important parameters for the performance of the upper part of the furnace. ?Coke-bed resistance; it will increase with the use of charcoal (a review of new results). ?Slag reactivity; a relevant method for testing slag reactivity of industrial reductants is of interest. The suggested method can serve for comparing slag reactivities towards graphite.

Jan 1, 2007

By Muhammad Zaka Emad

Cemented rockfill (CRF) is a mixture of rock aggregate and binder slurry. It is a stiff backfill, it is fast curing, its operation is simple, placement rate is reasonably high and no drainage is required. The main demerit of CRF is failure of exposed faces causing ore dilution, which can be associated with the fill placement method. This paper discusses the effects of two placement methods being practiced by mines and numerical modelling is used as a tool to evaluate stability of the backfill column. In the first method, practiced in longitudinal retreat mining of a narrow vein deposit, the rockfill is hauled and dumped into the stope with a LHD scooptram. Once dumped, cement slurry is sprayed into the stope. In the second method, a raise situated centrally above the mined stope is used to convey already mixed CRF into the stope. Stopes are mined out transversely in primary and secondary blocks in a sublevel stoping system. Problems of poor mixing in combination with both placement methods are discussed. The two backfill placement methods are analyzed for blast induced vibration damage using the dynamic Flac3D modelling technique accounting for rock mass and fill damping characteristics, and a pressure wave is used to simulate the blast vibrations. Fill heterogeneity has also been considered for the two cases and results are compared.

Jun 1, 2012