Search Documents

By James W. Collins

The bucketwheel stacker/reclaimer is suited for a variety of bulk material handling systems, especially those operating with stockpiles in excess of 30,000 tons. The bucketwheel stacker/reclaimer, although relatively new in the United States (first introduced here in 1964), has been successfully used in European countries since the early 1940's. Basically the machine is the outgrowth of the bucketwheel earth excavator and the traveling tripper boom type stacker. Since their introduction here they have achieved wide acceptance, especially with coal fired power plants. (Figures 1, 2, and 3.) The stacker reclaimer has been utilized in barge and ship loading/unloading facilities, and in the material handling systems for steel mills, where it has been used to stack and reclaim iron ore at rates up to 6000 tph stacking and 4000 tph reclaiming. They have also been employed at mine mouth power plants for the handling and storing of the plant fuel supply and to help balance the mining rate with the fuel consumption rate.

Jan 1, 1973

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.1 This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material in. which the crystals here dealt with were grown was made from 1/8-in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, ass nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. MEASUREMENTS The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, ?, from one direction of the wire axis, and an azimuth or longitude, [ø], from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most. of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

Jan 1, 1928

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By Bruce C. Trent

In order to effectively model subsidence caused by underground openings, a two-dimensional computer code has been developed which couples near- and far-field response. The near-field is simulated by a discrete element block code and a finite difference code represents the continuum region in the far-field. The explicit equations allow rapid and inexpensive solutions to geometries which may lead to subsidence. Two sample problems are presented which illustrate the important features of the code.

Jan 1, 1979

By B. F. Fackenthal

The earliest history shows that, in the reduction of iron-ores, natural draft was used to supply the blast, and that, when artificial blast was first used, it was supplied by leather bellows, usually made of skins, which were worked by the feet or hands, the blast entering the furnace through one tuyere or nozzle. The prehistoric bellows and its tuyere or nozzle are still in use in some form wherever iron is made. The original Durham furnace, built in 1727 at Durham, Pa., which was one of the earliest blast-furnaces in this country, was blown with a bellows, the power being supplied by a waterwheel. The old records show the purchase of leather at various times to repair the bellows, and mention the freezing of the water-wheel as one of the causes for going out of blast. In the early days of our iron manufacture but one tuyere was used; in fact, a cousiderable number of charcoal-furnaces continued to use but one tuyere down to recent years. I am

Jan 1, 1899

By V. Annamalai, J. B. Hiskey, L. E. Murr

The kinetics of copper cementation on rotating disks of body and tear-top beverage can aluminum alloys were studied as a function of temperature and copper ion concentration. Both alloys followed the two-step kinetic regions, an initially slow rate followed by an enhanced rate. Experimental activation energy determinations (9.04 to 19.62 kJ/mol) indicated that ionic diffusion controlled the reaction mechanism between 20° and 60°C. At low temperatures (< 20°C), the system appeared to be controlled by the presence of an aluminum oxide surface film. The results of this study showed that cementation kinetics for the beverage can aluminum alloys are similar to those for pure aluminum. It was also found that the chemical removal of the oxide layer is less important for the alloys than /or the pure aluminum system. The characteristics of the resultant copper deposits were studied under a scanning electron microscope, and the reaction kinetics seemed to depend strongly on the nature and morphology of the deposits. In addition, maximum rates occurred when the deposit structures were fine feathery dendrites.

Jan 1, 1980

By B. M. O'Harra

The residues resulting from the retort distillation of zinc ores have from 40 to 75 per cent of the weight of the original ore and contain from 5 to 15 per cent zinc . A rough estimate indicates that approximately 450,000 tons of residues are produced annually in the United States , containing about 36,000 tons of zinc . Besides the current production of residues there are at many smelter sites large accumulations from past operations which are available for treatment if this can be done profitably . In addition to their zinc content the residues contain much unconsumed coal , which has been carbonized during the distillation process , and those from most western ores also contain lead and silver . In this paper is summarized the information obtained in a survey , recently made by the Bureau of Mines , in cooperation with the Missouri School of Mines and Metallurgy , of processes which are in use or which have been suggested for the treatment of retort residues . The complete report of the survey is to be published as a Technical Paper of the Bureau of Mines .

Apr 1, 1923

By Rolf Andreas Lauten, Adam Pratomo, Dani Ramdani, Helminton Sitanggang

A universal challenge for the mineral processing industry is the diminishment of high grade ores. Instead, low grade ores, sometimes also containing problematic gangue minerals is the reality. With lower head grades the industry has to put more effort into processing to maintain the output and achieve suitable recoveries. In an effort to reduce the impact of declining head grade, a biopolymer was evaluated as an additive in the gold leaching operation at Antam Pongkor in Indonesia. Laboratory testing revealed that biopolymer usage lead to an increased gold recovery without apparent negative impact on the other parts of the process. Further plant trials revealed both a recovery increase around 1.3% and higher throughput (9%) in the presence of the biopolymer. Some scenarios that can explain these findings will be discussed.

Jan 1, 2014

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550&apos;F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550&apos;F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By G. W. Poling

Sedimentation behaviour of siliceous mill tailings derived from a magnetite-chalcopyrite ore in fresh water, fresh water - sea water mixtures and full-salinity sea waters are compared. Results of batch settling tests are presented in the form of settling curves and solids flux curves. The addition of a few per cent of sea water markedly enhanced the zone sedimentation rate due to particle agglomeration caused by a reduction in zeta potential of the suspended solids. The presence of a small amount of residual, previously magnetized magnetite in the tailings also enhanced agglomeration and sedimentation. The significance of these results to submarine disposal of mill tailings is discussed.

Jan 1, 1973

By Stephen Iverson

The National Institute for Occupational Safety and Health (NIOSH) is currently performing research to help mine operators minimize the amount of loose or damaged rock surrounding a blasted opening. Improperly designed blast rounds can result in excessive wall rock damage that may reduce the rock mass competency and increase ground support requirements. Unnecessary blast damage can cause many safety and operational concerns including an increased potential for injury from rock falls and other hazards resulting from sub-optimal blast designs. This paper focuses on the ground control and safety implications of blast damage in underground mines. A reduction in rock quality due to blasting can increase the amount of ground support required. Case study data collected by NIOSH in underground metal mines during standard drill and blast production rounds included blast vibration monitoring, detailed three-dimensional laser scanning of the as-built excavation, and geotechnical mapping of development headings.

Jan 1, 2007

By Andrzej Wala, Henry P. Cole, Perry David Passaro

Cognitive representations and misconceptions of flow through circuits is an area which has received little attention from science educators, cognitive psychologists, or accident investigators. Misconceptions are also called Aristotelian thinking. They involve a person using primitive unscientific ways of reasoning to make decisions about events (Piaget, 1929; Nussbaum & Novick, 1982; McCloskey, 1983). The use of such primitive concepts leads to errors in reasoning about scientific and technical problems. The existence of misconceptions is well documented among children, adolescents, and adults involved in learning science concepts (Piaget, 1929; Cole & Raven, 1969; Clement, 1982; Mistrell, 1982; McDermott, 1984; Richardson, 1987). Concepts of flow through circuits are important because miners&apos; conceptual errors about these aspects may be, in part, responsible for two fatal mine disasters. On at least two separate occasions, methane gas explosions occurred in underground mines when separate ventilation systems were connected (Elam, Fuller, Carter, Cavanaugh, Fesak & Painter, 1983; Fesak & Cavanaugh, 1984). A review of these disasters indicates that conceptual errors made by miners may have resulted in the accidents (Cole, Wala, Haley, & Vaught, 1987). In this study, co-author Andrzej Wala, stated that his research had "identified conceptual errors that may have caused the miners in these disasters to make fatal mistakes" (Cole et al. 1987), p. 167. Further exploration of these conceptual errors by Wala has led to the hypothesis that misconceptions of basic aspects of flow distribution changes in mine ventilation circuits, are at least, in part, responsible for some mine disasters caused by errors in ventilation systems (Wala & Cole, 1987). Why should these conceptual errors occur? Ausubel (1963) suggested that students come to a new area of study with their own conceptions or preconceptions about how a process operates. Furthermore, these preconceptions may be in conflict with the empirical data from the discipline. In such cases, learning becomes a process in which new concepts must displace or be re-molded from stable concepts that the student has constructed over many years (Clement, 1982). Given the existing research with misconceptions and the work of Wala and Cole (1987), it was hypothesized that experienced miners; either working miners, students of mining engineering, or professional mining engineers, harbored misconceptions about the formal or conceptual aspects of mine ventilation circuits. The misconceptions hypothesized to exist involved flow distribution changes in complex mine ventilation circuits; specifically, how does flow distribution change when a ventilation circuit pathway is altered? Given this information, the following research questions were proposed. Research Questions 1. Do experienced miners and mining engineers harbor misconceptions about mine ventilation systems? This question was addressed by: A. The administration of the Cutthrough Ventilation Arrangements (CVA) exercise that measures subjects&apos; performance level when making decisions about major ventilation changes when connecting two mine sections;

Jan 1, 1989

By Xiaoming Huaa

The effect of the anodic polarization on the composition and morphology of the surface layer formed on chalcopyrite during ammonia–ammonium chloride leaching was investigated. The anodic polarization on the chalcopyrite electrode was used for oxidation and dissolution of chalcopyrite, and the resulting oxidized layers were characterized by XPS, SEM and optical microscopy. The results show that oxide layers exist on the chalcopyrite surface with or without any anodic polarization in the leaching solution at ambient atmosphere. However, the composition and morphology of the layers are strongly depended on the extent of polarization. The distribution of FeOOH and Fe2O3 within the oxidized layer was inhomogeneous for the sample at the open circuit potential (OCP). The composition and morphology of the oxidized layers which were formed at anodic potentials lower than 0.3 V versus SCE were similar to those of the chalcopyrite at the OCP. At anodic potentials above 0.4 V, the oxidized layers contained many cracks, and they were fragile and exfoliated. Furthermore, the sulfide had been oxidized to sulfur species with higher oxidation states. The oxidation of the chalcopyrite seemed to undergo a cyclically oxidative process that suggested growth and spallation of oxidation layers on chalcopyrite in a layer-by-layer sequence.

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well approved Tunnel Seismic Prediction System (TSP) has been substantially enhanced for online geological prognosis in underground construction. The method provides high resolution seismic images of the rock mass ahead of a tunnel face via an array of standard anchor rods. These contain3D-geophones and can routinely be installed during the excavation process. A further outstanding feature of the system is the newly developed high frequency repetitive seismic source which can easily be fixed at a tunnel boring machine. A user-friendly software package enables online data acquisition, processing, 3D-visualization, and interpretation.

Jan 1, 2001

By H. Kenworthy

"INTRODUCTION ..Although the occurrence of iron ore in Missouri was recognized by Marquette as early as 1673, the first known mining and smelting operation was conducted in 1815. This operation was near Arcadia, Iron County, the first of its kind west of the Mississippi-Ohio River system. Several small furnaces of short life were erected in Missouri in the ensuing 30 years. However, until the extensive deposits of Iron Mountain and Pilot Knob were opened between 1843 and 1850, the state remained a minor producer of iron. It was this district which was chiefly responsible for the prominent position Missouri held in the iron industry until the late 1880's. At this time the easily minable high-grade ores became exhausted and the discovery of the immense Lake Superior deposits depressed the raw-ore price to such an extent that any mines ceased to operate. 3/Small yearly production of iron ores continued in Missouri to the present. Owing to war demands for hard ore suitable for open-hearth steel, the M. A. Hanna Co., through its subsidiary, the Ozark Ore Co., reopened the Iron Mountain, deposits and installed new equipment in an old concentrator to handle the low-grade ores left from previous operations. At present, ore production is from open pits, but underground mining is contemplated in the future. About 2,000 tons a day of iron ore is treated by gravity concentration of material from the open pits in the immediate vicinity. The concentrate is shipped to the Birmingham, Ala., district and to Granite City, Ill., for smelting. The coarse tailing is sold for ballast and concrete aggregate. The iron requirements of the concentrate stipulated by the purchaser are not difficult to meet, but the phosphorus is frequently higher than desired. For 1946 the concentrates averaged 54.18 percent iron and 0.235 percent phosphorus with low sulfur. The Ozark Ore Co. concentrate, however, sometimes contains as much as 0.40 percent phosphorus. The phosphorus in ores from those portions of the deposits wherein the phosphorus occurs with siliceous gangue is readily rejected in the milling, but in much of the ore the phosphorus is associated with the iron and concentrated with the iron minerals. Selective mining is impossible owing to the spotty occurrence of the phosphorus mineral. Often within 5 feet the ore will change from low phosphorus to high phosphorus, and it would be expedient to find a method of rejecting enough phosphorus at the mill from the latter type of ore to meet the phosphorus specification."

Feb 1, 1948

By Liu Y

Ventilation, air leakage, and various cutting, loading and support movement operations all have a role in dust distribution on longwall faces as shown by the results of a large number of dust measurements on different longwall operations in the Bulli seam on the South Coast. It is concluded that leakage of air on the face has demonstrable mfluence on the exposure of the shearer operator to dust level. It is possible to calculate dust generated by various elements of a rrurung operation on the face from a single point measurement. In the examination of dust deposition from the source of generation as a function of particle size, it is found that respirable dust can remain airborne over long distances without any significant drop in concentration, if unobstructed.

Jan 1, 1995

By John Wulff, Robert Kamm, Steinberg Morris

In powder metallurgy it has often been observed that shrinkage may occur in one direction and growth in another during sintering. Even in long-time sintering experiments the rate of shrinkage may be different in different parts of the compact. In the fabrication of some parts requiring a constant permeability it is even questionable in some cases whether pressing from one direction should be attempted. These observations require for their interpretation a more detailed study of green or pressed density than has heretofore been available. Usually average density measurements of the whole compact are made and in some cases carefully cut sections are measured. A different approach to the problem was first mentioned by Rakowskil and also used by Balshin.2 Balshin&apos;s diagram is reproduced in Fig I and schematically shows the result of pressing three layers of metal powder with fine intervening layers of graphite. The retarding effect of the die walls and a qualitative example of the density distribution is evident. More quantitative information about the distribution of density within a cold-pressed powder compact would be useful in showing the variation in density in as as influenced by the type of poKder, shape of die, lubricatioll during the process, and other variables. Furthermore, information about the cracking of cold-pressed compacts may be obtained from an analysis of the stress distribution within a, powder compact, and some information about the stress distribution can be obtained in turn from the derlsity and strain distributions. A more detailed report on some of the present experiments appears in reference 3. Present Investigation In order to ascertain the density gradients in cold-pressed metal powders, a deformable lead grid within the powder was employed. After pressing in cylindrical di" the ejected compact was radiographed, giving a pattern of the deformed grid. From the radiograph density and deformation from point to point is readily measured. From the radiograph strain distribution and stress trajectories were also determined. The latter also permits the determination of the coefficient of friction at the die wall. This technique indicates that the densest Part of a compact pressed from one side is at the top outer circumference and the least dense region at the bottom circumfercnce near the stationary plunger. For Some heights of compacts the density at the axis is such that the lower density is at the top rather than at the bottom. SO irregular a density distribution is due primarily to die-wall friction. As the ratio - diameter to height of compact is increased the die walls play a correspondingly smaller role. More uniform density

Jan 1, 1947

By John Wulff, Steinberg Morris, Robert Kamm

In powder metallurgy it has often been observed that shrinkage may occur in one direction and growth in another during sintering. Even in long-time sintering experiments the rate of shrinkage may be different in different parts of the compact. In the fabrication of some parts requiring a constant permeability it is even questionable in some cases whether pressing from one direction should be attempted. These observations require for their interpretation a more detailed study of green or pressed density than has heretofore been available. Usually average density measurements of the whole compact are made and in some cases carefully cut sections are measured. A different approach to the problem was first mentioned by Rakowskil and also used by Balshin.2 Balshin&apos;s diagram is reproduced in Fig I and schematically shows the result of pressing three layers of metal powder with fine intervening layers of graphite. The retarding effect of the die walls and a qualitative example of the density distribution is evident. More quantitative information about the distribution of density within a cold-pressed powder compact would be useful in showing the variation in density in as as influenced by the type of poKder, shape of die, lubricatioll during the process, and other variables. Furthermore, information about the cracking of cold-pressed compacts may be obtained from an analysis of the stress distribution within a, powder compact, and some information about the stress distribution can be obtained in turn from the derlsity and strain distributions. A more detailed report on some of the present experiments appears in reference 3. Present Investigation In order to ascertain the density gradients in cold-pressed metal powders, a deformable lead grid within the powder was employed. After pressing in cylindrical di" the ejected compact was radiographed, giving a pattern of the deformed grid. From the radiograph density and deformation from point to point is readily measured. From the radiograph strain distribution and stress trajectories were also determined. The latter also permits the determination of the coefficient of friction at the die wall. This technique indicates that the densest Part of a compact pressed from one side is at the top outer circumference and the least dense region at the bottom circumfercnce near the stationary plunger. For Some heights of compacts the density at the axis is such that the lower density is at the top rather than at the bottom. SO irregular a density distribution is due primarily to die-wall friction. As the ratio - diameter to height of compact is increased the die walls play a correspondingly smaller role. More uniform density

Jan 1, 1947