Search Documents

By S. J. M. van Leeuwen, R. Feenstra

The effect of jets on bit penetration has been investigated by means of a 50-ton drilling machine and 8½-in. commercial jet bits, drilling under representative bottom-hole conditions. The conclusions apply to the drilling of impermeable rock only. Penetration rate is in all cases primarily hampered by a differential pressure effect, known as dynamic hold-down. Jet action can reduce this slightly. Major gain in penetration rate, up to 25 or 50 per cent, is already ohtained at medium-high jet power. At high bit load, penetration by soft to medium-hard-formation bits is further hampered by bit-balling. Its alleviation requires intensive tooth scavenging, which is best performed by slanted nozzles with trailing, high-velocity, high-volume jets, hitting bottom in front of the teeth. Penetration may then improve by a 100 per cent. At high bit load, bottom-balling limits the penetration of insert-type bits. In this case bottom scavenging is required, which is most effectively performed with high velocity jets from nozzles extended close to bottom. As a result of this measure, penetration may improve 70 per cent in non-friable rock, and less in friable rock. This will make the insert-type bit more versatile. Toothed hard-formation hits suffer at high bit load from both bit- and bottom-balling. Slanted nozzles, possibly much extended, with high-velocity, high-volume jets then have best prospects. INTRODUCTION For years the use of jet bits in oil well drilling has been increasing, in conjunction with ever greater hydraulic horsepower. To the same extent, the need for efficient use of the horsepower has grown.' This paper, it is hoped, will contribute to an understanding of how effective jet action may be obtained. It deals with the effect of jets on phenomena that are known' " to hamper bit penetration. To study this effect, laboratory drilling tests were performed with 8½-in. commercial bits under bottom-hole pressures representative of deep wells. The investigation has been restricted to the drilling of practically impermeable rock. In the following sections, the increase in bit penetration rates due to jetting is discussed for conditions which made the troublesome phenomena stand out one at a time. A brief definition and interpretation of these phenomena is given in Appendix A. Appendix B gives the results of measurements of fluid velocities along the hole bottom, performed in stationary flow tests. Descriptions of equipment, bits, rocks and mud are collected in Appendix C. Unless otherwise mentioned, drilling conditions were kept standard as given in Table 1. CUTTING TRANSPORT TO THE ANNULUS Jet action was for some time believed to merely improve the transport of cuttings from bottom to annulus, resulting in a clean hole bottom. Flow tests performed in 1954 at the Battelle Memorial Institute6 showed, however, that jet velocities of the order of 40 ft/sec sufficed to clear even large (0.4-in.) chips from bottom in the time between two successive tooth actions. In the field, optimum jet velocities are appreciably higher, indicating that other effects must be involved. This much is confirmed by the results of our drilling experiments in soft rocks performed under atmospheric pressure, i.e., in absence of pressure-differential effects. Fig. 1 shows that variation in the nozzle velocity from 40 to 330 ft/sec had no effect on penetration rate, unless the bit penetrated more than 7 mm per revolution, which is about half the tooth height. At such high rates—150 ft/hr at 100 rpm—cuttings would be caught in the tooth cavities, leading to bit-balling, which was noticed on inspection of the bit. The jets thus assisted in keeping the tooth cavities clean. This is just perceptibly reflected in the penetration-rate curves of Fig. 1: Much the same results were obtained in hard rocks with hard-formation three-cone bits. The conclusion is that transport of loose cuttings towards the annulus does not require a powerful jet action. In the following sections we shall see that in deep-well drilling other phenomena are of greater importance. DYNAMIC HOLD-DOWN It is generally accepted that, in deep-well drilling, bit penetration is hampered primarily by the existence of a difference in pressure between the fluid in the hole and that in the rock at the depth of cutting.2-5 In the drilling

Jan 1, 1965

A discussion of the paper by Mr. Campbell, which was read by title at the Lake Superior meeting, but first presented at the New York meeting of the Iron and Steel Institute, October, 1904 (see p. 772). These papers are here published onder a mutual agreement between the Councils of the two Institutes, and will also be found in the Journal of the Iron and Steel Institute for the year 1901, vol. ii. Mr. William R. Webster, Philadelphia, Pa., said: We are under great obligation to Mr. Campbell for his exhaustive investigation, and the results he has put before us to-day. They are the most conlplete series of tests that have ever been made, where all the conditions of rolling, etc., were kept uniform. In discussing Mr. Campbell's first investigations, I claimed first, that the method of least squares, then used, would of necessity only gire the average value of any element, and that if the effect of any element was greater in the presence of high carbon than with low carbon this would not be shown by the method of least squares. Secondly, that the effect of manga nese should be considered on acid steel as well as on basic steel, instead of ignoring all the eff'ect of that element when it was below 0.60 per cent., as was then recommended by Mr. Campbell. I am pleased to note that the results of his present investigation confirm my views on these points. In presenting the results of his first investigation, Mr. Campbell referred to my investigation of 1893-94, and took exception to the value of phosphorus varying (depending on the amount of carbon present) from 800 to 1,500 lb. for each 0.01 per cent. He claimed that one might just as well consider the effect of phosphorus as being constant, and of carbon varying. I refer to this, as he now has introduced very similar conditions in his present tables, in that he gives variable values for manganese (depending on the amount of carbon present) for both acid and basic' steels. Can we now say, with more certainty than formerly, which element should be considered as haviup a constant effect ? There is one other point that I took up in my former discus-

Jan 1, 1905

By J. A. Herrick

Jan 1, 1879

By Reinhold Schnell, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e.,metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine. The findings of and lessons learned from this case study can be applied toother mine operations to improve safety, production, efficiency, and cost savings. Focus areas for the project included refined communications, operational practices and procedures, planning, designing, and data collection and analysis. This case study showed improved efficiency in communication and planning among the engineers, operations team, and contractor groups over the course of the project. An increased awareness of long-term plans and needs for the drills and blasters reduced or eliminated existing delays. Test blasts that implemented new drill and blast designs and updated operational practices and procedures were tested to streamline the process. Constraints regarding explosive product shipments, geological considerations, and a uniform powder factor provided the basis for new blast designs.

By A. L. Murray, P. A. Surgeon

The Spring Canyon Mine Rescue Association is a cooperative association supported jointly by five coal-mining companies located in Spring Canyon, Utah. The properties of mining companies the Carbon Fuel Co, Rains , Utah, the Liberty Coal Co. , Latuda, Utah, the Standard Coal Co. , Standardville , Utan, the Spring Canyon Coal Co. , Storrs , Utah, and the Peerless Coal Co. , Peerless , Utah about a mile apart and normally employ a total of 915 men , 733 underground 182 on the surface . and The Association was organized on July 5, 1921 , and Rudolph Clark, fomerly first - aid miner on U. S. Bureau of Mines Rescue Car 11 , was placed in charge. as manager . A board of directors made up of a representative from each of the cooperating companies (usually the mine superintendent ) is the governing body of the Association and the expenses are prorated on a basis of the production of each of the five mines . The Association maintains eight sets of Gibbs rescue apparatus and a motor truck fitted up as a combined rescue truck and ambulance . Additional apparatus are to be purchased . Standardville is the central camp in the canyon and has been made the headquarters of the Association . The apparatus are now kept and the truck housed in a small station, but plans have been prepared for a large station which will be built this summer . This new station will have a large apparatus room , a test chamber, a suitable room. for training, and a garage on the first floor, while above will be the living quarters of the manager . There is a good road through the canyon and the other camps are all within two and one -half miles of Standardville .

May 1, 1922

By C Dell

Hillgrove, situated on the New England plateau of New South Wales, is an area rich in history and resources. Key resources are predominantly antimony, gold and scheelite and the area surrounding the historical field is environmentally sensitive and topographically challenging. Since acquiring the Hillgrove leases, Straits Hillgrove Gold has undertaken a significant exploration program on these historical mining areas with the goal to return the field to production. This exploration program has enabled Straits to significantly increase the resource base and has subsequently enabled the planned redevelopment of Hillgrove to be realised. In October 2006, installation of mining infrastructure and the initial stripping of existing development had commenced. To successfully redevelop Hillgrove, Straits has had to adopt a highly mechanised, trackless, diesel mining operation which will see the production rate commence at an initial rate of 250 kt/a of ore from a narrow vein environment. This ore will be processed on site to produce antimony metal, gold bullion and a scheelite concentrate.

Jan 1, 2008

By G Hayes

Ore from the Browns deposit near Batchelor, in the Northern Territory of Australia, is a fine-grained polymetallic sulfide ore hosted in graphitic black shale. Minerals of economic significance are seigenite (Co,Ni)4S3, Galena (PbS) and Chalcopyrite (CuFeS2) with minor Sphalerite (ZnS). Gangue minerals include quartz, carbon and K-feldspar. The grain size is fine, with a significant amount of the seigenite present as Early flotation work determined that a grind size of around 20 microns was required to achieve clean sulfide concentrates. This work recommended oil agglomeration flotation, in which small sulfide minerals were collected, then loosely agglomerated with oil ahead of flotation into a heavily mineralised froth. In the 400 kg/hr prototype plant this froth proved unmanageable. A conventional flotation circuit after grinding to a P80 of 24 microns and using very low flotation pulp densities resulted in an 86 per cent cobalt recovery.The paper analyses further laboratory work which has increased cobalt recovery to 91 per cent by grinding to û250 microns ahead of flash flotation. The real cobalt recovery breakthrough comes from flash flotation of the whole mill discharge rather than the more usual flash flotation of cyclone underflow. Flash flotation tailings are ground to û38 microns and are floated under normal flotation conditions with only the scavenger concentrates being reground to 20 microns.A one tonne per hour prototyping campaign is scheduled to demonstrate the robustness of this circuit.

Jan 1, 2002

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

A system to continuously measure the concentration of radon in mine ventilating air has been developed and tested in a uranium mine. In use, the air/radon mixture to be monitored is pumped through filters into a scintillation cell where nuclear decay of the radon produces flashes of light. These are electronically counted, giving a quantitative measure of the radon present. Air is continuously drawn from the mine atmosphere into the radon sensor box. This air sample passes through two filters into the detector cell as shown in the schematic diagram. A portion of the radon in the detector cell will experience nuclear decay, producing polomium 218 and an alpha particle. The alpha particles from the fraction that decays strike a zinc-sulfide coating on the inside wall of the cell and produce flashes of light. These enter a photo-multiplier tube which records each flash as an electrical pulse. An amplifier increases the voltage of each pulse, allowing electronic screening to remove noise and other undesirable pulses. The remaining pulses are counted by a conventional data acquisition system.

Jan 1, 1978

By Javier Casas, Richard Corsino, Miguel Baylon, Miguel González

El presente trabajo consistirá en presentar la metodología realizada para la inyección de cianuro a presión en el pad 1A, la cual contempla la realización de estudios de las condiciones del pad, barrenación de los pozos de inyección y de monitoreo, realización de pruebas metalúrgicas, inyección de cianuro a presión, monitoreo geotécnico en la inyección, y finalmente los enjuagues realizados. Finalmente se presentarán los resultados obtenidos de las onzas de oro y plata recuperadas de esta prueba piloto y los planes futuros que se tienen acerca de estos trabajos.

Sep 30, 2022

By Jon H. Gould

This paper describes the following at the new Advanced Solid Rocket Motor (ASRM) nozzle manufacturing facility, which is being constructed inside an existing manufacturing facility: 1) generalized subsurface conditions, 2) pile load test program and evaluation, 3) pile selection, 4) problems associated with pile driving operations, and 5) production pile installation. The poor subsurface conditions, known and unknown underground obstructions, and work environment inside the existing building, used to manufacture the Space Shuttle external fuel tanks, required special pile installation equipment, procedures, and work schedules to install the economical pile foundation system ahead of schedule and without a lost time accident. GEOTECHNICAL STUDIES In April and May 1990, 16 soil test borings were drilled inside the existing building with a truck-mounted drill rig. The borings extended to depths ranging from 60 to 65 ft (18.3 to 19.8 m) below the floor slab. Typically, the silty and clayey soils were sampled by pushing "undisturbed" Shelby tubes, and the more sandy soils were sampled by driving a Standard Penetration Test (SPT) split-spoon sampler. The unconfined compressive strength, water content, and unit weight of the Shelby tube samples were measured in the laboratory. A geotechnical report was issued in May 1990 presenting the results of the field and laboratory testing and foundation recommendations (Gilbert, 1990).

Jan 1, 1992

By Carlos Pañura, Michael Geldres, Alejandro Rojas

The vibration waves are produced by the detonation of the explosive charges of each blasthole, analyzing the vibration waves produced by each blasthole, allow us to determine the optimal time between the detonation of each blasthole to reduce the vibrations of the production shot. Once the optimal time is found, it is possible also, to predict the vibration of the production shot (considering times and sequences) using predictive models. The waveform recorded includes information regarding the particle velocity and the dominant frequencies of the vibration.

Feb 1, 2020

By M. D. Mwema

Copper oxide ores deposits in the Katanga province of the Democratic Republic of Congo (DRC) contain at variable level cobalt oxide minerals. In contrast to copper oxide minerals which readily dissolve in the sulphuric acid solution, the cobalt oxide bearings are difficult to dissolve, especially if cobalt is present in the third oxidation state (Co2O3). This species become soluble after reduction of Co+3in Co+2. In practice, the use of reducing agent is therefore necessary in order to transform the insoluble minerals into soluble cobalt sulphate species. The following reducing agents are currently used at the Shituru plant: ferrous ions, which are present in leach solutions, pulverised copper or sodium meta bisulphite (MBS). Due to the high consumption of reducing agents (0,8 t MBS/t of solubilized Co; 1,2 t Cu/t-Co), cobalt production is expensive. The use of sulphur dioxide as reducing agent was then investigated in order to reduce operating cost. This reagent also presents the advantage of sulphuric acid production during the leaching process. It has been added in the leaching vessel (tank). From the laboratory and industrial tests, selective leaching of cobalt (78%) has been performed. The cobalt leaching kinetic depend on sulphur dioxide dosage. Dissolution of copper, iron and manganese remained very low. No emanation of SO2 gas was observed during the process.

Jan 1, 2002

By R. Koen, H. Visser, A. Roodt

"SynopsisThe tetraethylammonium salt of the mono-anionic coordination compound mer-oxidotrichlorido(thenoyltrifluoroacetylacetonato- K2O,O’)niobate(V) (NEt4)[NbOCl3](ttfa)], has been prepared under aerobic conditions and characterized by single-crystal X-ray diffraction. (NEt4)[NbOCl3](ttfa)] crystallized in the monoclinic P21/c space group, with a = 11.483 (5), b = 12.563 (5), c = 17.110(5) Å, and ß = 100.838 (5)o. The complex structure exists in a 50.0% (NbA) : 50.0% (NbB) positional disorder ratio.IntroductionComplexes containing organometallic type ß- diketone ligands with O,O and O,N donor atoms are used widely in coordination chemistry and have applications in catalysis, radiopharmaceuticals, etc. (Schutte et al., 2011; Roodt, Visser and Brink, 2011; Brink et al., 2010; Otto et al., 1998). These ligand systems are very useful because of their highly coordinative nature, high solubility, and also due to their ability to be functionalized with various substituents on the carbonyl carbon atoms (Schutte et al., 2011).Only a small number of ß-diketonate ligands have successfully been coordinated to a Nb(V) metal centre, with only a select few being characterized by X-ray crystallography (Viljoen, 2009; Bullen, Mason and Pauling, 1965; Preuss, Lamding and Mueller-Becker, 1994; Funk, 1934; Davies, Leedlam and Jones, 1999; Allen, 2002. The synthesis and crystal structure determination at room temperature of mer-oxidotrichlorido (thenoyltrifluoroacetylacetonato- k2O,O’)niobate(V) {(NEt4)[NbOCl3(ttfa)]} was first reported by Daran et al. in 1979. Accordingly, for this current investigation, (NEt4)[NbOCl3(ttfa)] was re-evaluated at 100 K to determine if the structural features might change with temperature."

Jan 1, 2015

By Dean Brox, Jason Morrison, Peter Procter

The Galore Creek Mine project is one of the newest major mining projects underdevelopment in Canada. The project is located in a very remote area of northwester British Columbia and is being developed by Nova Gold Resources of Vancouver. The mine project comprises one of the largest and highest grade undeveloped porphyry-related gold-silver-copper deposits in North America. In order to access the mine site anew 120 km road is planned to be constructed including a 4.4 km mine access road tunnel. Glaciers with heavy snow pack cover approximately two-thirds of the tunnel alignment with a maximum cover of 1,200 m. The size of the access road tunnel is about 50 m2 and has been designed as a large single lane road tunnel to accommodate the transport of large size mining equipment for mine start up and ongoing operations. The rock conditions along the tunnel alignment comprise very strong volcanic rocks. Key services for mining operations will be incorporated into the tunnel comprising diesel and power as well as the concentrate pipeline. Structural portal canopies have been incorporated into the tunnel design due to the risk of rockfalls and avalanches in the portal areas. The mine access road tunnel is a significant and critical-path component to the overall project to provide vehicular access to allow construction of the mine site. In order to meet the expected mine start up date the construction of the tunnel works are to commence prior to any other works at the mine site and will be constructed entirely by helicopter support. Geotechnical investigations commenced in the summer of 2006 with the removal of the overburden materials at the portals to assess bedrock conditions. Tunnel construction from both portals is expected to commence in the spring of 2007. The construction of the mine project is subject to and awaiting environmental approval in the spring of 2007. The mine access road tunnel will be the longest private road tunnel in North America. The key design and constructability issues for the mine access road tunnel project are presented and discussed.

Jan 1, 2007

By A M. Lechner, S Arnold, M J. Gillespie, P D. Erskine, D R. Mulligan, A T. Fletcher, A Gordon

Mine ecological monitoring schemes are often conducted only to address compliance and in some cases do not have the sufficient statistical power or understanding of ecological systems to assess, quantitatively, the meeting of rehabilitation targets or mine impacts. Monitoring schemes for rehabilitation commonly rely on analogue sites or premining baselines (reference sites) to assess whether rehabilitation sites are ecologically similar and thus successfully rehabilitated. In the case of monitoring for mine impacts, if the impacted sites diverge from reference data, the site is considered to be impacted. Fundamental to any monitoring scheme is testing the sampling design to ensure that it can detect these differences if they are present through adequate sample sizes (ie statistical power). However, a good understanding of the ecological system is required to ensure that differences detected are ecologically significant. Modelling ecosystem properties can provide a quantitative understanding of how ecosystems change over time and space, in response to natural environmental variations and thus aid in determining significant ecological differences. Furthermore, modelling methods can be used to predict future ecosystem states. Within the ecological literature, guidelines for robust statistical monitoring designs and modelling methods exist but are not routinely being used in the mining industry. This paper uses simple examples to discuss: problems with current compliance monitoring methods; importance of robust statistical techniques; and how modelling can assist rehabilitation assessment and guide monitoring schemes. The aim of this paper is to describe general monitoring and modelling methods that could be potentially used for mine site monitoring and closure assessment. These methods are often considered by mining companies as an extra expense that provide little practical benefit, and the domain of academia; however, engaging these methods may be more cost-effective in the long-run than conducting untargeted monitoring schemes that give no confidence to regulators on whether rehabilitation criteria have been met. Furthermore, monitoring programs in mining contexts provide a good opportunity to better understand long-term ecological patterns and test the application of more rigorous modelling approaches as the life of many mines tends to be greater than ten years.CITATION:Lechner, A M, Arnold, S, Fletcher, A T, Gordon, A, Erskine, P D, Gillespie, M J and Mulligan, D R, 2012. Embracing modern ecological methods - Monitoring and modelling for mine closure, not compliance, in Proceedings Life-of-Mine 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By B. H. Moore

The opportunity to evaluate the pile design procedures used on a major project is an infrequent occurrence. It is even more infrequent that the project involves piles with significant tension and horizontal capacities. This report synopsizes over twenty years of design and construction experience on just such a major pile founded structure. The philosophy governing foundation design procedures is described and discussed. The order and extent of full scale pile testing are evaluated. Principal points in the specifications are established and their effect on construction progress and claims are noted. The report concludes with recommendations for future projects.

Jan 1, 2010

By D M. Frantois-Bongarton

Variograms can be powerful tools for the analysis and control of process streams and their sampling. Their uses and proper utilisation have been described somewhat unclearly to date, and their limitations and precautions of use are too rarely mentioned. The general meaning and properties of the variogram tool and its use in geostatistics are therefore reviewed in details to derive a critical view of its proper use for process control: what to expect from it and what it cannot deliver and which uses are illusory or potentially misleading. A summary of GyÆs seminal work accompanies this essay to put the concepts into historical perspective.CITATION:Frantois-Bongarton, D M, 2012. Review of variogram properties and remarks on its use in process control, in Proceedings Sampling 2012 , pp 175-180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Don Ibana

Supported by the Minerals Council of Australia (MCA) through the Minerals Tertiary Education Council (MTEC), three Australian universities–Curtin University, Murdoch University and the University of Queensland–have formed the Metallurgical Education Partnership (MEP) to jointly develop and deliver an engineering design capstone unit–Metallurgical Process and Plant Design–in their respective undergraduate programs in extractive metallurgy, in order to enhance the students’ educational experience. A unique feature of the program is the close interaction of the students in all three universities and a significant involvement of industry professionals. Now in its sixth year, it is clear that this unit is achieving its objectives

Jan 1, 2014

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951