Search Documents

Boiler-Room Economy "Establishing and Maintaining Boiler-room Economy" is the title of a paper presented before the Ohio Society of Mechanical Electrical and Steam Engineers by Geo. H. Gibson, of which the following is an excerpt: Boiler-room economy depends less upon equipment than upon operation, i.e., it depends largely upon the condition in which the apparatus is maintained and how it is used. A given boiler may operate this week with an efficiency of 78 per cent., and next week with an efficiency of 65 per cent., while using the same fuel and developing the same rating. If there are variations ii; character of fuel and in load and other factors, the falling-off may be even greater, possibly to less than 60 per cent. The steam produced may cost twice as much per 1,000 lb. at one time as at another. Most steam plant managers know from their own experience that these statements are not exaggerated. It does not take much of a plant to run up a coal bill of $5,000 per year, many "spend $10,000 for coal, and fuel bills of $50,000, $100,000, or $200,000 per annum are not uncommon. As it call be shown in the majority of these plants that 10 per cent. of this amount may be saved, and in large numbers of them 25 per cent., while in some the expenditure can be cut in half, there is no disputing that we have here a subject worthy of attention. In the production of steam the greatest variable is the human factor. Before we can pass judgment, however, we must first have standards. This implies accurate quantitative knowledge of fuel consumption and steam production. We must measure the output and know how much the steam costs per thousand pounds, and how many pounds of steam are obtained from a pound of coal. We can then begin to analyze the problem, and find where and how methods and conditions can be improved, and how much. Many favor buying coal on a B. t. u. basis. This is advisable where the amount purchased warrants the considerable expense involved in systematically gathering samples that: are. truly representative and in having analyses made, of every carload. Coal analyses, combined with. an honest endeavor on the part of the miner to ship good coal, should insure the receipt of the heat units paid for. , It often happens, however, that the coal which is cheapest on a B.t.u. basis is not the cheapest or most suitable for producing steam, because of peculiarities of the plant in which it is to be burned, or conversely, the fuel which furnishes cheap B.t.u. may require special methods or equipment for its economic utilization.

Jan 2, 1916

By W. O. Philbrook, A. E. El-Mehairy

The reduction by hydrogen of individual particles of dense hematite implanted in beds of inert spheres is controlled by single-particle kinetics. No evidence of reagent starvation was found down to low flow rates established by pressure gradients as low as 0.01 in. H2O per- in. of depth in beds of spheres as small as 3/16 in. diam. The optimum size for most rapid reduction of beds of homogeneous ores results from the effect on reducing potential of the gas of competing factors of supply and consumption. A recent publication1 presented the results of a study of the rate of reduction of iron ore in a fixed bed by hydrogen introduced at constant pressure differential. Under these conditions the reagent flow rate varied directly with the bed permeability, which was a function of particle size and shape and bed voidage, and inversely with the temperature-dependent viscosity of the gas. The present note adds data from supplementary experiments designed to reveal whether or not any partial reagent starvation arising from a flow-dependent transport resistance in the gas phase might have been operative. Kinetic studies were made of the reduction of individual spheres of iron oxide inserted into beds of inert spheres, so that the reagent flow rate and aerodynamic conditions were again determined by bed characteristics and temperature. The experimental techniques and apparatus were similar to those previously described.' The synthetic iron ore spheres were wet-rolled by hand from powdered, reagent-grade* Fe2O3 and subsequently dried and then fired in air at 1250°C. The indurated pellets has almost no porosity as indicated by their specific gravity of 5.10. The beds were made of dense alumina spheres, closely sized to the same dimension as the iron oxide spheres, in the following diameters: 3/16, 1/4, 5/16, and 3/8 in. Each bed was hand-packed of particles of a single size to a controlled voidage of 0.32 and depth of 3 in. within a capsule having an internal diameter at least 10 times the particle diameter. A few weighed iron oxide spheres were individually planted in the central plane of the bed of inert spheres at points away from the wall. Reduction was carried out at atmospheric pressure by purified hydrogen at 670°, 800°, and 985°c. The reagent was supplied at precisely controlled pressure differentials of 0.01, 0.02, and 0.03 in. of water per in. of bed depth. This gave a range of flow rates similar to that used in the study of beds of ore and comparable with blast-furnace practice in terms of mols of reducing gas per hr per sq ft of cross-section. Viscous flow prevailed in all beds under the experimental conditions of this study. The reduced particles were checked for loss in weight and then sectioned for metallographic examination. Occasional particles were found to have contained minute internal cracks that interfered with the concentricity of the reduction interfaces, and data for such particles were rejected. An experimental rate constant for the reduction of the imbedded Fe2O3 spheres was calculated on the assumption that the rate was proportional to the metal-oxide interface area by an equation that has been found by McKewan2 to describe the reduction of single spheres

Jan 1, 1962

By M. Askari, M. H. Parsa, S. Kashani-Nejad

Sarcheshmeh refractory consumption rate is about 7.5 - 8 kg/ton of the produced copper, which is almost three times higher than the other smelters practice. High destruction rate of tuyere zone refractory controls vessel productivity and operational lifetime. In this research with the aid of cold model and computational fluid dynamic (CFD), melt recirculation pattern and gas - liquid plume properties in the wide range of gas blowing conditions were studied. Results revealed that in addition to the well-known mechanical refractory destruction mechanism, fast tuyere zone refractory destruction could also be related to the cold bubble cluster formation near tuyere tips and introducing severe thermal shock to the refractory surface. Removing accretion and its strong bonds to the refractories around tuyere tip, causes refractory mechanical destruction and increases tuyere diameter. Increased tuyere diameter, in turn assists gas discharge in the bubbling regime. Air blowing in the bubbling regime result in the formation of big bubble clusters, bubble breakup and back attack occurrence which all found to have major impact on the refractory lifetime. Outcomes of this research, contributed to the plant converting management, blowing hardware and instrumentation improvement.

Jan 1, 2004

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By L. M. Pruett

The Arizona Legislature is currently in the process of considering mined land reclamation legislation in the 1994 legislative session. A bipartisan legislative study committee has drafted proposed mined land legislation. The committee has attempted to craft legislation that is appropriate for the unique conditions in Arizona. Existing Arizona and federal laws and regulations extensively regulate the environmental performance of mines in the state to protect public health, safety and the environment. The proposed mined land reclamation legislation does not replace or duplicate these statutory provisions relating to environmental protection. Instead, the purpose of the proposed legislation is to provide for the reclamation of land that is being mined and to fill the gap in existing laws by requiring the reclamation of land that currently is being mined or that has been mined since 1986 to provide for future land use. The legislation would require an operator to submit a reclamation plan describing the exploration operations, mining operations, post-mining land use and the proposed reclamation measures for review by a state agency. Financial assurance also would be required in an amount such that a third party could complete the approved reclamation measures. Arizona's mined land reclamation legislation would recognize Arizona's leading role in hard rock mining and emphasize the mining industry's economic importance to Arizona and the nation. Because mining operations necessarily require disturbing the surface of the earth to extract valuable minerals, reclamation requirements would be adapted to different conditions and would vary depending on site-specific conditions and on the commodity being mined. The current proposal does not identify the state agency that will administer the mined land reclamation program and approve reclamation plans, substantial changes to plans, and transfers of reclamation plans to other operators.

Jan 1, 1994

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002

By A Kamkar-Rouhani

The paper describes a mineral potential mapping of gold and other base metals in Mahneshan area, Iran, using geographical information system (GIS), in which, the method of weights of evidence is used to combine spatial data obtained from different sources to make prediction for mineral potential. This is a quantitative tool for mineral resource mapping that can be used to delineate and predict favorable areas for further exploration by using the characteristics of known and similar mineral deposits. In accord with the descriptive model for gold and other base metal deposits, the spatial distribution of 20 known mineral occurrences was used. In addition, digital evidential maps were used in this study. The maps include maps of lithological units, faults and first derivative of total aeromagnetic data, remotely-sensing data of alteration and also geochemical evidential maps produced on the basis of the results of chemical analyses of samples taken from the stream sediments in the area, and analysed for Cu, Pb, Zn, Sb, As, Ag, Au, Ba and Hg elements. The binary maps were produced and then combined with the model of weights of evidence using 20 known mineral occurrences to obtain a final map of the favourable areas for further exploration of gold and other base metals in the study area. The final map is a predictive GIS model of the mineral deposits in the area. An interesting matter about the final predictive GIS model is that the faults are mainly located in favorable areas which possesses the most probability of mineralisation. Therefore, the faults in these areas have priority for further exploration of gold and others base metals.

Jan 1, 2005

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

Residual aeolian placers (RAPs) are formed by the wind, by preferential entrainment and removal of small and low-density detritusfrom a pre-existing, typically sedimentary sequence containing heavy minerals. Heavy minerals that are resistant to chemical alteration and either soft and malleable (gold), or extremely hard (diamond, sapphire, ruby, etc), are concentrated as a residual on the wind deflation surface, typically in the interstices between larger resistant clasts. RAPs form preferentially in arid or semi arid areas, where the vegetation is sparse or absent, and where topography and surface gradients are low, but may also form on beaches and in periglacial environments. RAPs consist of a continuous or discontinuous, planar or gently undulating horizon of heavy minerals in a single-clast-thick pavement of resistant pebbles, cobbles, or boulders, which mantles the present topography or palaeo-topography. Extreme wind erosion and surface deflation may condense the full pre-existing sequence into a layer of heavy minerals only. The grade of RAPs is substantially higher than in the precursor deposit, and commonly much higher than those typically found in most other placer types. Aside from their general occurrence as a thin pavement of resistant clasts, the best indicators of residual aeolian gold placers are the presence of wind-eroded stones (ventifacts) on the pavement, and the distinctive and unique shapes of aeolian gold grains themselves. The shape of the gold grains is progressively transformed by sand blasting during placer development, from grains with thickened rims, to toroidal grains on which the rims are æsplitÆ and peened inward toward the grain centre on one or both of the grain sides, to hemispherical or sub-spherical grains that are fully encapsulated by the in-turned rims. Gold that has undergone aeolian shape transformation is difficult to entrain and transport away from the site of aeolian concentration by anything other than mass movement or glacial processes. It is also easily retained by commercial recovery plants of any configuration.

Jan 1, 2004

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962

By George R. Cowan

A number of studies hare been reported of the effects produced in metals subjected to deformation by shock waves with maximum pressures ranging from tens to hundreds of kilobars. On the basis of the equations for the flow of mass, momentum, and energy through a stationary shock front, the macroscopic stress-strain curve for the resulting shock deformation can be calculated within narrow limits from the experimentally determined Hugoniol curve. In relatively weak shocks which are preceded by an elastic wave, the stress rises above the clastic limit only as plastic deformation proceeds cold thus the shock has a long toe. In strong shocks that override the elastic wave a high stress is applied without prior plastic deformation. A more important effect of increasing the shock pressure is the generation of shear stresses, called supercrilical shear stresses, that exceed the strength of the perfect lattice. A change in the mechanism of deformation is expected to result from the onset of supercritical shear. The shock disordering of ordered Cu3Au in strong shocks appears to be an example of such a change. It is suggested that the formation of fine twins in copper and nickel and the formation of structures which enable visible twins to be formed in the rarefaction ware, observed in copper and presumably in disordered Cu3 Au, are related to the occurrence of supercritical shear in shock dcformation. In recent years several studies1,2 have been made of the changes in structural and mechanical properties of metals produced by the passage through the metals of strong shock-compression waves ranging from about 50 to 800 kbar pressure. Recent work involving dynamic measurements of the shock compression "Hugoniot" curves 3-8 of many metals has developed techniques and provided data required to obtain the shock pressure and the (transient! plastic deformation produced in the shock-conlpression experirnents.9 Shock deformation has been found to be much more effective than slow deformation in changing the mechanical properties of metals, when the two are compared on the basis of equal plasti strain, Holtzman and Cowan9 made quantitative estimates of the shearing stress occurring in a shock front in a metal by assuming that the shearing stress is similar to that occurring in a shock front in a viscous, heat-conducting fluid, with the addition of a yield stress. Taylor&apos;s solution9 for a weak shock was used to estimate pairs of values of shearing stress and thickness of the shock front obtained by assumed choices of the ratio of effective kinetic viscosity to thermal diffusivity. It was noted from these values that. unless the shock front is extremely thin. heat conduction has slight effect, and the shearing stress is nearly independent of the mechanism of deformation. This mechanism does, however, determine the thickness of the shock front and the rate of strain. Furthermore, since the maximum possible shearing stress occurring in shocks of moderate strength does not greatly exceed the shear stress occurring in conventional slow deformation, the mechanism of deformation is not expected to be qualitatively different. The greater effectiveness of shock deformation in changing the mechanical properties of metals can be attributed partly to the fact that dislocations, when driven by near-conventional stresses, cannot keep up with the shock front, thus necessitating a higher dislocation density than required for an equivalent slow strain. The fast uni-axial strain occurring in the thin shock front would also be expected to cause a larger number of dislocation intersections to occur. In the upper range of shock pressures that have been studied the estimated values of the shearing stress exceeded the estimated shear strength of a perfect crystal. Under these circumstances it is reasonable to expect that the mechanism of deformation might be considerably different from that involved in slow deformation. Except for the observation by smith1 of twins in shocked copper, the effects of shock waves on metals did not show any obvious or large changes in properties that would indicate the onset of a change in the mechanism of deformation. The recent investigation of the effect of shock waves on ordered and disordered specimens of Cu3Au by Beardmore, Holtzman, and ever" showed a spectacular decrease in the amount of long-range order retained by initially ordered Cu3Au when the shock pressure was raised from 290 to 370 kbar. Since Dr. Holtzman and I suspected that this behavior probably was due to the onset of a shearing stress in the shock front in Cu3Au which exceeded the limiting shear strength of the perfect crystal. it was considered appropriate to examine directly the shock-front equations for a solid. and to obtain a sound estimate of the shearing stress occurring in the front using equation of state data obtained from shock studies. In this paper an estimate is made of the

Jan 1, 1965

By D. J. Archambeault, A. Saigal

Substantial cost savings have been demonstrated by material design changes after initial product development. As more information about a product&apos;s operating environment becomes available to a designer, it is possible to consider a more costeffective material that still meets or exceeds the design intent, such as minimum low cycle fatigue life. This is especially true in the aircraft engine industry, where precise operating cycle data is not available until after the first engine is built and tested. A methodology for predicting estimated low cycle fatigue life has been developed to investigate potential material change candidates for an aft cooling plate. A twodimensional macromechanical finite element model (FEM) has been developed using ANSYS and used to determine the effects of varying material properties. It is shown that slight changes in density, coefficient of thermal expansion and modulus of elasticity have profound effects on component and effective stresses, and therefore, estimated low cycle fatigue (ELCF) life. Aerospace

Jan 1, 2006

Gardner I?. Williams, authority on diamond mining, died at San Francisco, Cal., on Aug. 22, after an illness of nearly a year. Mr. Williams, who was in his eighty-first year, was born in Saginaw, Mich. He was graduated from the University of California in 1865, and afterward took a course at the Freiberg Mining Academy in Saxony. He was awarded the degree of LII. D. by the University of California in 1910, and Doctor of Engineering by the University of Michigan in 1917. Beginning in 1870, Mr. Williams spent two years as assistant assayer at the United States Mint in San Francisco. He successfully developed

Jan 1, 1923

Gardner I?. Williams, authority on diamond mining, died at San Francisco, Cal., on Aug. 22, after an illness of nearly a year. Mr. Williams, who was in his eighty-first year, was born in Saginaw, Mich. He was graduated from the University of California in 1865, and afterward took a course at the Freiberg Mining Academy in Saxony. He was awarded the degree of LII. D. by the University of California in 1910, and Doctor of Engineering by the University of Michigan in 1917. Beginning in 1870, Mr. Williams spent two years as assistant assayer at the United States Mint in San Francisco. He successfully developed

Jan 1, 1923

By L. Bloomquist

This paper describes how Automated Mining Systems (AMS) is evolving the state-of-the-art in guidance systems for autonomous underground vehicles. The techniques, trade-offs, and lessons learned from these systems are described, including the safety regime that has been implemented. First generation autonomous guidance systems for underground vehicles relied on infrastructure for the vehicle to follow. However, there are additional costs associated with that approach. The current generation uses a pair of laser range finders as its only guidance sensors. This system uses a minimum of infrastructure, in the form of a redundant system of location referencing. Advanced steering and drive control algorithms are incorporated into this generation of system. The next generation of infrastructureless guidance systems will be based on a 3D vision sensor, which was originally developed for autonomous Mars rovers and is being adapted for underground mining use. Results of early underground field trials are presented, along with a description of this emerging technology.

Jan 1, 2004

By B Rouvray, R Bertuzzi

The development of a design-and-construct tunnelling project in Australia from its concept to its construction requires designs to be prepared and reviewed at several distinct stages prior to documenting ‘for construction’. On recent projects the post-tender stages have been variously called 30 per cent—70 per cent—100 per cent; or concept–substantial–final; or system definition–preliminary–critical. The design is reviewed at each stage by the designer’s internal reviewer, the contractor and its independent advisor(s), the owner and its independent advisor(s), the project’s independent certifier, proof engineers and often third-party stakeholders and their advisors. Documentation for each stage often dominates the design effort, at times distracting from design. This paper presents the authors’ experience of this design-and-review process. Comparisons of design budget and actual design spend and design program implications are presented. It is postulated that a subtle change has occurred in our industry that has diminished the value of the design dollar. Is there a better process? An alternative is suggested.CITATION:Bertuzzi, R and Rouvray, B, 2014. Reducing the cost of tunnel design in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 501–506 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R. G. Bradburn

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit test- work combined with an analysis of operating data showed that (1) metallurgical personnel, at times could increase production rates by as much as 10 percent over that achieved by grinding operators, (2) the chosen data base required an increase of 2 percent or more to be statistically significant and (3) for a 2 percent increase there would be a significant rate of return of investment in a computer installation, Consequently one grinding circuit was fully instrumented, and a rented control computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long term objectives. The short term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been met as described in this paper. Statistically significant increases in excess of 2 percent have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long term objectives are (1) off line analysis of the circuit using mathematical models of process units, (2) on line experiments to study alternative contol tactics, and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1976