Search Documents

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By C. L. Severy

The Reeder No. 1 well was drilled by the Bureau of Mines in cooperation with the Geological Survey as agents for the Defense Plant Corporation. The well is south of Crescent Junction near Thompson, Grand County, Utah. It was started May 5, 1942, and completed August 3, 1942, for the purpose of con-firming the presence of magnesium salts in a deeply buried bed. Drilling was done under contract by the Mack Drilling Co. This report contains an outline of the physical features of the well, a brief history of drilling, and a description of the deposits and occurrences of oil and gas encountered in the drill hole. The work performed by the Bureau of Mines is described in considerable detail, with particular emphasis on drilling procedure and sampling. The report is concluded with a brief description of core-sample preparation for analyses. Appendix A comprises a log of the drill hole, and appendix B is a tabulation of analyses of cores.

Jan 1, 1949

By T. A. Dungan

THE thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. EARLY EXPERIMENTS IN DIRECT REDUCTION The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbothermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was expected to obtain metallic magnesium. The results were positive and metallic magnesium was

Jan 1, 1944

By André Boyer

El presente artículo señala que los revestimientos de goma en los molinos son un aporte positivo en la minería -en tanto reducen las horas de parada y su costo por tonelada por una mayor duración. En ese sentido, las parrillas de descarga en goma aumentan el rendimiento de los molinos entre 20 y 25% de su capacidad por overflow.

Jan 1, 1975

By J. E. Danoczi

ABSTRACT A diamond processing plant is being designed for the Star–Orion South diamond project in central Saskatchewan. Key to the plant is diamond liberation, which occurs in the comminution section and is the process of breaking up kimberlite rock as gently as possible to minimize diamond damage, particularly in larger, high-value diamonds. Kimberlite from the crater area of a volcanic pipe is generally softer than kimberlite from the diatreme zone. Softer kimberlite, comprising the majority of Star– Orion South deposits, can be readily broken up using abrasion and attrition by autogenous grinding mills, the preferred comminution method for minimizing diamond damage.

Jan 1, 2013

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By S Agdaca

Leightons is the sole contractor at the Wahana Coal Mine Project (part of the Bayan Group), a multi-seam thermal deposit consisting of 13 coal seams with thicknesses ranging from 20 cm to 500 cm. The average dip of the deposit is 18 - 20°. However the deposit is heavily faulted in certain domains with anticlinal and synclinal structures present causing seams to dip up to 90°. Average thickness of coal inter-burdens range from less than 2 to 12 m. The minimum coal thickness being mined is 20 cm. Coal production is direct mine mouth feed and there is no coal processing plant currently used.Conventional blasting between the highly variable coal horizons in the early phases of the mine life was suboptimal from a production perspective. Drilling short holes with a reduced drill pattern, and on occasions with sloping benches, resulted in low drilling and explosives loading efficiency.A high frequency of small size blasts fired up to two times daily was required with each blast consisting of four up to five small blast areas. Each blast averaged approximately 36 000 bcm thus causing a low utilisation rate of the mining fleet from frequent blast delays and the inability to deploy larger Liebherr 9350 excavators on bench. It was identified that increasing the production targets required a more efficient drilling and blasting process. Furthermore, due to the highly variable nature of the deposit, the existing coal model was determined to not be able to accurately predict the coal seam location prior to blasthole drilling.In August 2009, Leighton Contractors Indonesia and Orica Mining Services with the full support of the Wahana team, initiated through seam blasting trials using electronic blasting systems. Further trials were conducted in November 2009. Trial evaluations indicated that the benefits from decreased lost time events due to blasting, an increased vertical advance rate per blast, and increased overall blast size could be attained while not damaging or diluting coal.Full-scale?through seam blasting has been ongoing since February 2010 for the upper eight coal seams to extract coal seam thicknesses ranging from 20 - 100 cm. This paper will discuss the parameters of the through seam blasting process in Wahana and the resulting benefits to the overall mine production.

Nov 8, 2011

By E. Ringdalen

Keywords: Pyrometallurgy, research, Norway, SINTEF, NTNU The Norwegian Ferro-alloy Industry and the model for research cooperation between SINTEF, NTNU, and the Norwegian ferro-alloy industry is presented as an introduction. The research within pyrometallurgy is illustrated by examples from characterisation of Mn-ores and characterisation of carbon materials. Examples from studies of reaction mechanisms in laboratory- and pilot-scale experiments are presented, in addition to an example of industrial off-gas measurements. Education possibilities at NTNU are also described.

Jan 1, 2011

By C J. Moran

Given that the mining industry is committed to sustainable development principles and that Australia is experiencing changes to the regulatory environment that aim to modernise the water sector and encourage adoption of consistent approaches, there is a well defined need for the Australian minerals industry to develop a water accounting framework. This requires: key terms and definitions for water metrics for use in the Australian minerals industry that is consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current requirements were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (water loss through evaporation is an example). The adopted terms and definitions dictated model development, with the conclusion that a systems approach was the most effective calculation process. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and can be adopted as the first step towards developing national water accounts for the Australian Minerals Industry.

Jan 1, 2009

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

By Kazem Oraee-Mirzamani, Nikzad Oraee-Mirzamani, Arash Goodarzi

"Unexpected movement of ground can potentially endanger lives, damage equipment or destroy property. Occupational accidents frequently occur with fatal consequences in developing countries with significant economic dependence on industries such as mining. Therefore, there is increasing need for miners' protection against such hazards. Slope stability and roof support accidents are two of the major causes of fatalities at surface and underground mining operations. According to national codes, employers are obligated to protect workers against accidents; however, these rules fall short of the standards in developed countries. National safety regulations should clearly specify support systems. The International Labor Organization (ILO) prepared two codes of practice, aiming to guide those responsible for improving standards of safety and to provide guidelines for drafting of safety regulations for the coal mine industry and quarry open cast mines. The practical recommendations of these codes in the ground control area have been analysed and the advantages and disadvantages of ILO codes concerning ground control are summarized.INTRODUCTIONTwo million people die every year from work-related accidents and diseases. An estimated 160 million people suffer from work-related diseases, and there are an estimated 270 million fatal and non-fatal work-related accidents per year. In economic terms, the ILO has estimated that 4% of the world's annual GDP is lost as a consequence of occupational diseases and accidents (ILO, 2009).Mining has always been dangerous due to many potential risks such as those associated with using machinery in enclosed spaces, rock falls, blasting operations and explosion of flammable gases, which endanger miners' safety and health. However, it is suggested that implementing new laws along with strict adherence would reduce such risks in the workplace.The severity and frequency of accidents are trending downward in developed countries, where the focus is on large private companies who invest heavily in mechanization and developing economies of scale. But in many parts of the world, particularly in developing countries, minerals are extracted by people working with simple tools and equipment; they work on a smaller scale, are more flexible, and can exploit irregular ore bodies and steep, dipping seams."

Jan 1, 2010

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues which may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Mining Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has now been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff co-operation across the country. MEA has also now commenced some international teaching initiatives which are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual university programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 1, 2009

The approach to this subject is a very general one, but an attempt has been made to cover briefly a very wide field in the nationally important job of manufacturing iron for the iron and steel industry.Some historical data concerning the development of the furnace itself from early days have been followed by the modern ideas on raw materials and their beneficiation. Recent furnace design and modern auxiliaries have been given attention with, finally, some developments in practical operation.HISTORICALWhen dealing with such large 'and costly operating units as blast furnaces, there is not the same opportunity for research in design as in most other metallurgical processes. Over past generations the development of furnace design, or "lines" as it is usually termed, as well as most radical operating changes, has been very gradual.However, there have been some periods of rapid progress due to revolutionary changes. One such was the adoption of the steam engine for blowing and charging operations, and also, during this same era, about 1750, coke was first used as fuel in place of charcoal. Another revolutionary change came some 100 years later, when heating the blast became usual practice.Since then there have been great improvements in mechanical equipment and in the preparation of raw .materials. These factors, together with a better understanding of what happens inside the furnace, have led to the development of those large mechanically operated structures which are the most modern in blast furnace design.For many, years America has led the world in pig iron production and in furnace development, so that American design and practice is now recognised almost as standard. This type of furnace replaced the older stacks in England, Russia, Germany, South Africa and India, as well as here in Australia.

Jan 1, 1947

Computer applications are ideally suited to the day to day operations of grade control and short term planning on a mine site. By refining this part of the operation there is scope to increase profits by more accurately predicting ore grade and tonnage, and allowing the mining engineer more flexibility in his approach to scheduling. Large numbers of blasthole or ditchwitch samples need to be processed in a fast and efficient manner, and stored in a database for future reference. The mining engineer has to calculate tonnages and subdivide the blast or digging area into mineable areas of waste, low and high grade ore. New grade and tonnage information must be used by the mining engineer to update his short term plan. Answers must be obtained quickly and efficiently, but a high level of individual input is necessary in order that maximum use is made of the information. Geostatistical analysis of samples can be used to refine the interpolation techniques. Reconciliation between the original grade model, the newly sampled area, and the final product should be monitored continually.

Jan 1, 1989

By Charles B. Dugger

Sacrificial linings for grinding mills have been a necessary state of the art of mineral dressing since the inception of comminution. Long recognized as the final link in energy transmission from power line to ore, mill liners as a scientific endeavor have not expanded as rapidly as other branches of mineral dressing engineering. Several reasons for this technological lag are apparent. Typically in the past, labor intensive foundries were freely located geographically, at a time when transportation charges made up a significant portion of the casting cost. Alloying agents had not gained their current level of sophistication and were relatively inexpensive in the quantities required. Precise foundry controls were not economically justified, or totally understood. Coincidental to these elements, liner consumption per unit processed did not categorically contribute as a major cost item to the mill operator. Grinding equipment was small, and many times lining life exceeded that of the promoter. These unique conditions no longer exist. Ore dressing equipment has grown to meet modern mining demands. Larger processing facilities, utilizing fewer pieces of equipment, have replaced operations of the past. Emphasis today and tomorrow is on larger and larger equipment, with an eye on lower and lower unit processing costs.

Jan 1, 1979

By A Nugraha, H Thanasekaran, K Tatetdagat

The Kanowna Belle gold mine is located in the Eastern Goldfields of Western Australia, approximately 18 km north-east of Kalgoorlie. The processing plant is designed to process 2 Mt/y and has the capability to treat both refractory and free milling ore from the Kanowna Belle and Kundana mining operations.The Kanowna Belle ore is refractory with the gold mineralisation occurring mostly as fine-grained inclusions in pyrite or as very fine-grained gold located in pyritic arsenic rich growth zones. The Kanowna Belle refractory process includes flotation, roasting of the flotation concentrate, and calcine leaching to extract the gold from the ore.Mineralogical analysis of feed and tailings streams from the flotation circuit have shown that the gold bearing minerals are well liberated and confirmed they are mainly associated with pyrite. Nearly 40% of the flotation circuit losses are in the -38 µm size fraction. To improve the flotation circuit recovery, the fine particle gold recovery was targeted. A Cavitation Tube column was selected for the site-based pilot test work program. This paper presents data generated from the on-site test work, and the benefits of the Cavitation Tube column to improve fine particle flotation.CITATION:Nugraha, A, Tatetdagat, K and Thanasekaran, H, 2018. Flotation circuit efficiency improvement at Northern Star Resources Limited’s Kanowna Belle gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 403–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018