Search Documents

By Raúl Gonzáles

El presente trabajo señala la estructura y funcionamiento de los cables metálicos de las minas a través de un probador electromagnético en CENTROMIN-PERÚ. Este instrumento de seguridad ha sido probado en las minas de Cerro de Pasco, Yauricocha, San Cristobal, Morococha y Casapalca, donde los resultados fueron satisfactorios, aunque las condiciones en los piques influyeron en los cálculos de resistencia de los cables metálicos. Afortunadamente, las instalaciones de CENTROMIN-PERÚ tienen más ventaja en el uso de dicho aparato, al tiempo que su uso detecta estiramientos y corrosión de los cables, ya que visualmente no son fácil de revelar.

Nov 20, 1978

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

Jan 1, 1970

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By M Jones

The past 100 years the mining industry can be characterised by a focus on increasing financial returns often to the detriment of social, human, manufactured and environmental capitals. Despite the sustainable development principles promoted by the International Council on Mining and Metals (ICMM), the Equator Principles and the African Mining Vision, which should have enhanced project promoters’ ‘licence to operate’ within a host community or nation, the industry has often failed to integrate proven innovations and best practices that enhance sustainability outcomes for mineral resource projects. This failure has led to delays, the abandonment of projects, with value destroyed for promoters, governments, host community and investors.The paper will outline the application of proven innovations, Enterprise Optimisation (EO), and Sustainable Operations (SUSOP®), during the pre-feasibility phase of a project. By determining the value of each capital before and after the application of proven innovations, the presentation will outline how and where value can be created across all five capitals over the life of a project or operation.The paper will demonstrate how the application of proven innovations significantly transforms the value-proposition of a mineral resource project or operation by generating additional value across all of the five capitals, reducing project risk, thus generating value for all stakeholders.CITATION:Jones, M, 2015. Fundamentally transforming the economic and sustainability signature of mining assets, in Proceedings Third International Future Mining Conference, pp 169–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Theo Lehner

Turning matte into anodes continues to be an area to watch: for visitors to see pyrometallurgy in action; for metallurgists to keep up with modern smelting furnaces and ever increasing production rates; for management to remain profitable using more tools than taught in school; and for environmentalists to detect the last small clouds from the ever cleaner smelter. Current converting practices have been screened and analyzed, and today, converting and casting is a modern industry. An impressive, though typical learning curve of converter productivity may be detected. Local conditions such as availability and type of raw materials, products extracted, cost factors, etc., have stimulated the development of add-ons or even alternatives to the still dominant method of converting by Peirce-Smith technology. Turning blister copper into anodes follows a similar path, namely increased productivity and improved quality. We dare to predict that development will continue.

Jan 1, 2005

By Alfredo Valdivia, Dominic Reda, Vojtech Gall

The design and planning for the construction of a new passageway to improve access and circulation to better accommodate anticipated increased passenger flow within Grand Central—42nd Street Station. The passageway includes the break-in of an over 100-year-old station cavern with an innovative design implementing a protective structure above the existing track to allow for safe train operations and passenger circulation during construction. Construction of the new passageway follows the Sequential Excavation Method. This paper will present the innovative solutions that went into the preliminary design and planning considering construction access, site logistics, risk management, structural retrofitting, instrumentation and monitoring, and impact assessments.

Jun 13, 2023

By W. E. Wallace, P. Bolsaltis, M. J. Keane, B. L. Rauaboni

Thermal treatment of respirable size silica dust samples results in marked changes in their hemolytic activity. These changes can be correlated with changes in the characteristics of the particle surface as measured by infrared spectra, zeta potentials, and specific surface area. Silica samples from various sources (Min-U-Sil, fumed silica, and a NIOSH standard sample) were heated or calcined at temperatures ranging from 100-1095C. The hemolytic activity of the crystalline materials decreased after thermal treatment. The behavior of the fumed material was found to be more complex. Material of very large surface area (small particle size) exhibits an initial increase in hemolytic activity upon calcination. This result confirms other experimental observations pointing to a particle size of maximum toxicity. Tre changes in hemolytic activity can be related to infrared spectra and zeta potentials of the materials. The absorption band in the 3200-4000 cm-1 frequency region of the fumed material disappears upon heat treatment while a sharp, characteristic band at 3750 cm-1 increases in intensity. Zeta potential measurements conducted in the pH range of 2.0-10.5 exhibit a unique change in zeta potential v.s. pH profile with heat treatment. These findings indicate that the removal of active surface silanol groups by calcination results in reduced cytotoxicity, as measured by a hemolysis test.

Jan 1, 1988

By Georg Unland, Thomas Wegner

"Different types of impact crushers use the physical effect of impact to crush rocks. The rocks can vary from soft to hard and from ductile to brittle but they should never be abrasive. Since the principles of impact crushing of larger rocks are hardly investigated these crushers are still sized rather by empirical than by scientific approaches.In order to investigate the principles of comminution by impact of large rocks a test rotor was developed and rocks of different dimensions were tested. The integrated measuring devices of the rotor enable the recording of impact forces and of absorbed impact energy with high resolution during the contact time.Since impact crushers stress the rock particles with a defined velocity the main crushing properties are gained as a function of the applied velocity and the particle size of the rock: likelihood of breakage, contact time, maximum crushing force, mass specific crushing work, surface related crushing ratio and crushed fragment shape distribution."

Jan 1, 2003

By M. Mortada

Nonsteady-state flow of slightly compressible liquids in porous media of non-uniform properties has been the subject of a number of recent studies. Most of these studies considered one-dimensional flow in systems with cylindrical geometry and with the properties of the porous medium varying with radial distance only. A. Houpeurt' studied the problem in its general form by examining the solutions of the differential equation, In Eq. 1, the permeability k and the porosity + are arbitrary functions of radial distance. Houpeurt concluded that, except for special forms of the functions k and the problem is not well suited for mathematical treatment, but lends itself to high-speed digital computation. Carslaw and Jaeger' discussed the solution of Eq. 1 for the case in which the permeability varies as a power of the radial distance. P. Albert3 studied analytically the pseudo steady-state solutions in systems of finite radial extent and non-uniform properties. He also obtained some numerical solutions for nonsteady-state flow using a high-speed computer. William Hurst4 examined the interference pressure drop due to a point sink located in an infinite system consisting of two permeability regions in series. In this case, the permeability changed at a radial distance r from the point sink. INTERFERENCE BETWEEN OIL FIELDS IN A NON-UNIFORM AQUIFER The interference pressure drop for oil fields located in an extensive aquifer of uniform properties is discussed in a number of places in the literature. This work considers the interference pressure drop for oil fields located in a non-uniform extensive aquifer comprising two regions of different properties as shown in Fig. 1. Region I of the aquifer extends from which is the radius of Oil Field A, to ar,,, where a>1. It has permeability k,, porosity +, and effective compressibility c,. Oil Field B is located in Region II which extends from ar, to infinity and has different properties from those of Region I, but the same formation thickness h. Region II has permeability k2, porosity and effective compressibility c2. The choice of this type of aquifer should not imply that it is of frequent occurrence. It is chosen primarily to illustrate the effects of non-uniform aquifer properties on oilfield interference. It is of interest to point out that a non-uniform radial aquifer in which both the permeability and the porosity are inversely proportional to the radial distance can be treated in a manner similar to a linear aquifer of uniform properties. The situation where only the permeability varies as the inverse of the radial distance is also amenable to analytical treatment. Both aquifers behave quite differently from a radial aquifer with uniform properties so far as the water influx and the interference pressure drop are concerned. METHOD OF SOLUTION The expression for the interference pressure drop in Oil Field B due to a constant rate of water influx in Oil Field A is developed in the Appendix. This is accomplished by the simultaneous solution of two partial differential equations describing the pressure in Regions I and 11. The two differential equations are solved subject to the following conditions: (1) at r,, the pressure gradient is constant; (2) at ar the pressure and

By C. M. Young

The safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced, In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could be accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap," would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of 1/2 in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in Fig. 1. In order to measure the temperature, a thermocouple was inserted in the center of the coil; the leads passed out at the ends and were ccnducted to a millivoltmeter. It is probable that the current of air passing upward through the coil resulted in the indication of a tempera-

Jan 1, 1920

By Steve Trussell, William H. Langer

"Arizona aggregate (sand, gravel and crushed stone) producers enjoyed more than a half a century of nearly constant growth in demand for aggregates. Approximately 80 percent of the aggregate produced in Arizona is sand and gravel, and 20 percent is crushed stone (U.S. Geological Survey, 2015). Figure 1 shows the generalized distribution of potential sources of sand and gravel (yellow) and potential sources of crushed stone (other colors described below). Black dots show locations of aggregate operations.Sand and gravel commonly is produced from modern river channels and terraces although some alluvial fans and high-level paleo-river terraces also serve as aggregate resources. The gravel clasts are a mix of rock types that reflect the types of rock in the source area of the rivers. Generally processed river gravels meet stringent specifications for highend uses.Crushed stone, which makes up about 20 percent of production, primarily comes from a variety of metamorphic rocks and light-colored intrusive igneous rocks such as granite (brown areas), dark colored extrusive igneous rocks such as basalt and scoria (rust colored areas), and carbonate rocks such as limestone or dolostone (green areas). Carbonate rocks are also used in the manufacture of cement and lime.Construction and aggregate production in ArizonaBecause aggregate producers have limited facilities for storing product, stockpile changes are insignificant compared to production. Therefore, demand or consumption of aggregate in Arizona is considered to be equal to production. Production figures used in this paper reflect shipments, sales or marketable production, including aggregate used by producers to make readymix concrete and asphalt. Production figures were reported by the U.S. Bureau of Mines from 1950 until 1995 and by the U.S. Geological Survey (USGS) since then. Production figures are reported voluntarily, and major operators are the primary source for these figures. Because many smaller operators do not report their production, the figures are conservative values that provide an approximation of aggregates production activity."

Jan 1, 2015

By S. Yaw Amponsah, E. Ben-Awuah, P. M. Takouda, P. Eme

Mining production scheduling is the process of determining the sequence of block extraction over a period of time that will yield the maximum net present value for a mining operation. The block extraction sequence needs to occur under certain resource constraints which presents an NP-hard problem that is computationally intractable and complex to solve for large scale problems using exact mathematical models such as Mixed Integer Linear Programming (MILP). In this paper, we used a metaheuristic optimisation model based on a Genetic Algorithm (GA) to solve the production scheduling problem. The problem definition and resource constraints are formulated using a mining specific GA that enforces block extraction precedence and mining capacity constraints through a normalisation method. A case study is implemented with the GA model, and the results and computational time are compared with that of a MILP model with CPLEX solver which is based on a branch-and-cut algorithm.

Sep 1, 2021

By A. Mahmoudkhani

There has been a continuous interest in chemical aids for processing Canadian oil sands by hot water extraction process since the first commercial industry operation in 1967. Several inorganic and organic chemical systems have been introduced, of which sodium hydroxide is the most widely used extraction process aid by major producers. Use of NaOH, however, results in accumulation of sodium ions in recycled water, causing higher clays dispersion and producing tailings with poor geotechnical properties that turn into mature fine tailings. This is especially true for low grade and oxidized ores, which present the greatest challenges in bitumen recovery and produce the major portion of fine tailings. In this paper, we are presenting a novel method based on use of inorganic polymers as process aids for various low grade oil sands ores. Denver flotation cell and a laboratory scale hydrotransport loop were utilized to evaluate the effect of chemical dosage and operating parameters on the processability of oil sands samples from Athabasca region. Process tailings were examined for properties such as water chemistry, suspended solids, settling rate and the ease of tailing treatments. Our results demonstrate that the use of inorganic polymers during the froth process lead to a significant improvement in bitumen recovery from low grade oil sands and can improve further tailing treatments. This offers a viable solution that can be easily incorporated into current processing facilities and deliver several operational and economical benefits. Advantages in use of inorganic polymers versus sodium hydroxide are presented in details.

Jan 1, 2012

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By Derek Apela, Coralee Heske, Bunyamin Kahraman, Muhammad Adi

Effective blast fragmentation is essential in underground mining, as it directly influences downstream processing efficiency and operational expenses. This study investigates the application of Non-Newtonian Fluids (NNF) as stemming materials, presenting a novel method to enhance energy confinement, minimize environmental impact, and optimize blast performance. NNFs exhibit shear-thickening behaviour, enabling them to transition between fluid-like and solid-like states under stress, which renders them suitable for regulating explosive gas ejection during blasting. Field trials were performed by Vale Base Metals in Thompson, Manitoba, in their underground nickel mine to evaluate conventional slag stemming against NNF-based stemming in production-scale blasts. Emulsion explosives were employed, and blast performance was assessed through velocity of detonation (VOD) measurements, vibration monitoring, and AI-assisted fragmentation analysis using WipFrag. Preliminary results indicate that NNF stemming improves fragmentation, resulting in a reduction of D50 by as much as 38%, enhances energy confinement, and may decrease the incidence of hole plugging and re-drilling in subsequent blasts. This study presents an alternative to conventional stemming methods, highlighting potential advantages for enhanced safety, efficiency, and sustainability in blasting operations. Additional research and field trials are necessary to improve implementation protocols and facilitate the widespread adoption of this unique method in the mining sector.

May 4, 2025

By Tomás Gonzáles

El presente trabajo describe la metodología usada para evaluar las estrategias de las alternativas del planeamiento a largo plazo en la explotación del mineral y el lixiviable en la Mina Toquepala.

Aug 25, 2002

By T. M. Barczak

This report describes Bureau of Mines research to develop methods to evaluate loading on longwall roof supports to permit better design and more efficient utilization of these structures in compliance with the geological conditions in which they are employed. The resultant vertical and horizontal force acting on the canopy of a shield can be determined, either from a statically determinate solution assuming rigid-body mechanics and elimination of certain unknowns, or from an elastic solu-tion by analysis of the load-displacement relationship of the shield structure. A two-dimensional rigid-body model is presented that determines resultant shield forces by measurement of leg, canopy capsule, and lemniscate link forces. An elastic solution is presented, in the form of an elastic stiffness model with two degrees of freedom, which describes the load-displacement relationship from the stiffness of the shield structure as determined in the Bureau's Mine Roof Simulator (MRS). The ability of both models to determine resultant forces acting on the shield canopy are evaluated from full-scale tests in the MRS. More advanced numerical models are also discussed as part of the Bureau's continuing effort in the evaluation of roof support structures.

Jan 1, 1987

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

By W J. Shaw

Mining operations must become more predictable to overcome the volatility that has characterised the mining industry. Comparisons of production against predictions will become more consistent as mining operations merge and expand, as personnel move from site to site, and as public reporting of reconciliations becomes more prevalent. More consistent approaches are already being seen in the industry using the terminology used in this paper and elsewhere.Examples are provided that show how use of the waterfall chart as a reconciliation management tool can provide objective analysis to improve practices.Geometallurgical modelling is becoming more useful and will continue to do so as we move from a few bulk samples to better interpretation of material properties from geological mapping and drill sampling. Reconciliation has evolved to the stage where predictions of geometallurgical properties to optimise mill performance, and of geotechnical properties derived from better 3D geological models, should also be reconciled.CITATION:Shaw, W J, 2014. Reconciliation – outcomes and expectations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 123–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014