Search Documents

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the ['tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the ['tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By R. R. Sayers

Ventilation may be defined as the process by which vitiated air of an enclosed or partly enclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level Per Cent. Oxygen.................................................. 20.94 Nitrogen................................................. 78.09 Carbon dioxide........................................... 0.03 Argon................................................... 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxide, ammonia, ozone........................................ traces Carbon Dioxide Limit For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent, carbon dioxide. Nevertheless, in mines it sometimes occurs in sufficient quantities to cause symptoms in men or even unconsciousness and death. One-half of 1 per cent. of carbon dioxide in normal air causes a slight and unnotice-able increase in the ventilation of the lungs, that is, a man exposed to one-ha,lf of 1 per cent. of carbon dioxide will breathe a little deeper and a little faster than when in pure air. If 2 per cent. of carbon dioxide is in the air, the lung ventilation will be increased about 50 per cent.; if there

Jan 1, 1927

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

 The paper demonstrates that Belle Fourche Shale (BFS), an abundant shale, can be transformed into a ceramic through careful characterization and thermal processing. The study explores the potential of BFS ceramics for use as refractories and thermal energy-storage devices, highlighting their high thermal storage capacity, good thermal shock resistance, and cost-effectiveness.

Dec 1, 2023

By Frank Field, Randolph Kirchain, Elisa Alonso, Richard Roth, Nathan Fleming

"High material prices and price uncertainty can be harmful to manufacturing firms. Increased use of recycled materials, industry-wide, can lower both material prices and price variability; moreover, increased recycling decreases the use of primary material, which mitigates price increases due to scarcity effects. These stabilizing and price lowering effects are explored using an Aluminum industry model. We show that (a) increased recycling leads to smaller price fluctuations in the presence of a primary metal supply perturbation, and (b) that the more substitutable the secondary metal is for the primary metal, the lower the overall material price is.IntroductionThe price of an industrial metal is expected to be a function of both the marginal cost of extraction and its scarcity[l-2]: where scarcity can be defined as the degree to which anticipated demand exceeds the known supply. Recycling end-of-life metal increases the apparent supply of the metal, or-in a functionally equivalent, but alternative conception-lowers the demand for primary metal; this lowers primary metal scarcity and should, theoretically, reduce its price. To the extent that this theoretical prediction holds true, recycling can provide benefits to consumers of industrial metals in the form of lower prices.Using a platinum industry model, prior work by Alonso[3] has shown that increased industrywide recycling can reduce metal price volatility because the secondary metal production (a) offsets virgin metal depletion, and (b) responds to supply-demand balance fluctuations more rapidly than the primary market. However, Platinum is not a typical industrial metal in the sense that secondary metal is perfectly substitutable for primary metal: Both primary and secondary platinum metal are functionally equivalent and have a common price. Other metals, such as secondary aluminum which is used as an example case in this study, contain varying degrees of other elements that were either intentionally added, or were inadvertently mixed in with the metal during the scrap recovery process. Consequently, different grades of scrap exist that have different profiles of elements in their composition. Depending on their particular profile of elements, more or less of a given grade can be used as a mass fraction of the final alloy-the secondary metal is not perfectly substitutable for the primary metal. For the purposes of this paper, the aluminum mass fraction of the final alloy that can be made up of secondary aluminum is termed the secondary substitutability of that grade in that alloy."

Jan 1, 2011

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

By P. S. Paul

Mine accidents/injuries are complex and generally characterized by several factors, from technical to social characteristics. In this paper, a sociotechnical model for work injury in mines was developed and tested through structural equation modelling with application to case study mines in India. In total 14 variables were considered in this study. Most of the variables are not directly quantifiable. Instruments were developed to quantify them through a questionnaire survey. Underground mineworkers were randomly selected for the survey. Responses of 300 participants were used for the analysis. The analysis was conducted in three parts. Firstly, high-low plots were constructed to explore the variations in responses to the questionnaires by the accident involved (AG) and non-involved (NAG) workers. Secondly, a t-test was conducted to see whether the responses were significantly different for the two groups or not. The chi-square results showed significant differences of responses among the two groups. Finally, how these difference scan cause accidents/injuries in mines was hypothesized and evaluated using structural equation modelling. The measurement model of the Linear Structural Relations (LISREL) program was used to identify the latent constructs of the sociotechnical model. The structural model of LISREL was used to estimate the interrelationships among the constructs. The case study results showed that there is a sequential interaction among the sociotechnical factors leading to accidents/injuries in mines. Work hazards induce more job stress in the workers while social support mitigates the same. Job stress and safety environment predict the workers? job involvement. A worker who is more job-involved exhibits better safety performance, which in turn reduces work injury. The safety environment is shown to have a direct mitigating effect on work-related injury. The findings of this study clearly revealed that job stress and safety environment are the two key factors influencing work-related injuries in mines that need to be addressed properly through effective safety programmes.

Jan 1, 2005

By S. L. Karunakaran

Selection of an appropriate foundation system requires great skill and ingenuity on the part of the designer. Certain guidelines for choosing between a pile and raft foundation are presented. A number of methods are available for estimating the capacity of piles, giving a wide range of values for the theoretical load carrying capacity. A few aspects to be taken into account while arriving at an appropriate theoretical capacity are discussed. The effect of fluctuation of water table level on the pile capacity and method of accounting for this factor on the pile capacity obtained through initial load test are also discussed. A case study presents a comparison between the estimated values of capacity of piles and the values obtained through the initial load test.

Jan 1, 1996

Energy Dissipation in Long-Distance Slurry Pipelines

Sep 13, 2010

By J. Kendall Hales

Jan 1, 2005

Copper waste dump leaching is growing in importance because of the.large tonnages (up to 250,000 ton/day) of low grade waste rock available from open cut mining of copper deposits and proof that controlled leaching of copper from such dumps can be profitable.Overburden or waste rock, ranging in size from large boulders to fines, is dumped as cheaply as possible on sloping sites. Copper is leached from the dumps by applying up to 12,000 gal/min of leach solution (a combination of spent solution from cementation and make-up water) to the top of the dumps by various techniques.Efliuent from the dumps is sent to a cementation plant for copper recovery.Factors which may be controlled, either directly or indirectly, to give a controlled copper content in the dump efliuent (usually 1-2 g/l.) are the cycle of operations (i.e. the alternate wetting and drying periods), thevolume of solution applied to the dump, pH, Fe2+ and Fe3+ content or redox potential, oxygen content, bacteria and their necessary nutrients, and temperature.Dissolution of oxide copper minerals appears to be mainly a function of acid concentration. Copper sulphide minerals need oxidation for dissolution to occur and this is accomplished by a combination of oxygen,ferric ion, and bacteria. Oxidation of pyrite, oxidation of Fe2+ to Fe3 +, and hydrolysis of Fe3+ are of some importance in leaching practice. The presence of gangue carbonate minerals is detrimental.Physical factors connected with penetration of solution into large rocks are important and the treatment of an individual dump usually extends over a period of many years. Recovery of copper from solution is usually achieved by cementation with iron (usually in the form of crumpled cans) but the use of sponge iron is becoming more important. Iron consumption varies from 1 to 4 lbiron per pound of copper. Preconcentration of the copper in the efliuent solution by solvent extraction followed by electrolysis may become a useful method.Application of dump leaching techniques to metals other than copper depends on finding an economic method of recovering the metal from solution...

Jan 1, 1967

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002

By J Loeb, D Thornton

Blast movement measurement is a key component of grade control, enabling mines to carry all of the precision involved in locating ore blocks, through a chaotic blast, to production. A monitoring system was developed about ten years ago so that mine operation personnel can measure three dimensional movement in every production blast. Research has shown that blast movement is always highly variable with a significant non-deterministic component. The consequence is that modelling will be inaccurate and therefore optimal ore recovery can only be achieved by direct measurement of blast movement.Three dimensional movement vectors are measured at discrete locations in the blast. If blast movement is only measured at one location in a blast pattern, data is severely limited and has all of the inherent inaccuracies of modelling a variable population. It is intuitive that the accuracy of defining the post-blast ore block mark-ups are proportional to the number of movement measurement locations, however increasing the number of monitoring locations causes increases to the direct operating costs of the mine.A cost-benefit analysis is used to explore the optimal number of monitoring locations. Using the method described in this paper, an automated selection of the number and location of blast movement monitors are analysed against the value of recovered ore compared to the control, for each trial.CITATION:Loeb, J and Thornton, D, 2014. A cost benefit analysis to explore the optimal number of blast movement monitoring locations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Geoffrey Purcell

Improvements which have been made in commericial flotation systems during the past fifty years have resulted more from trial and error methods in the mill than from research in the laboratory. Research has often provided explanations of why mill changes have improved the metallurgical process. Hopefully, in the next fifty years, changes in mill flowsheets will come about, primarily, as a result of research work. However, since minerals, in their infinite variety, cannot be reduced to a standard state, research on commercial ores will have only a local utility, and research on pure minerals will have little commercial application. What will emerge from research on pure systems are mechanisms of adsorption, and this in turn may throw some light on the very much more complex adsorption processes taking place in the pulps of commercial ores. Quartz, without a doubt, has been the subject of more research effort than any other mineral, but we are still a long way from completely understanding its behavior in flo¬tation. Hematite and calcite have received considerably less attention. Ores containing a mixture of all three minerals, however, are commercially important, and the iron deposits in Alabama have been extensively studied by the United States Bureau of Mines (1). The literature reveals no reports of research on synthetic mixtures of all three.

Jan 1, 1967

By John Kruse, Sethu Raman, Dave Tenney

The Cullaton Lake B-Zone gold mine was the first gold producer in the Kaminak Subprovince of the Canadian Shield . Located approximately 650 km north of Thompson. Manitoba, the mine produced 77,783 ounces of gold and 5,564 ounces of sil ver from 251 ,236 tons of ore during 1981-84 period. The depos it is a small , structurally controlled , stratabound orebody in an Archean iron formation. Most gold occurs in sulphide and silicate fac ies. Based on new ev idence, the depos it is interpreted to have fo rmed by remobilization of syngenetic low-grade gold mineralization in the iron fo rmation in a favoura ble fold structure. The concept and methods developed at the mine have been successfull y applied in the discovery of new deposits in the area. One of the concepts. which link Archean and Proterozoic mineralization. may have wider applications in the search fo r gold deposi ts elsewhere in Canada .

Jan 1, 1986

By John L. Lamont, Walter Crafts

THE principle formulated by Grossmann1 for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the in¬creasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been determined. The results of the study offer strong confirmation of the general validity of Grossmann's multiplying principle. TESTING PROCEDURE Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 20 in Grossmann's paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann's paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

By J. Herbst, J. A. Kitchner, J. P. Anfruns, G. Poling

Measurements have been made of the rate of capture of single particles of strongly hydrophobic, surface-methylated, quartz, of sizes ranging from 12 to 40 pm diam., by single rising bubbles of diam. 0.5 to 1.1 mm. The results agree closely with the theoretically calculated hydrodynamic collision rates, indicating that, in this system, every collision results in capture and retention of a particle.

Jan 1, 1976

By J. A. Kitchener, J. P. Anfruns

Measurements have been made of the rate of capture of single particles of strongly hydrophobic, surface-methylated, quartz, of sizes ranging from 12 to 40 µm diam., by single rising bubbles of diam. 0.5 to 1.1mm. The results agree closely with the theoretically calculated hydrodynamic collision rates, indicating that, in this system, every collision results in capture and retention of a particle.

Jan 1, 1976

By A. G. Buyers, J. Chilton, W. E. McKee

STUDIES in the high-temperature separations chemistry of thorium-uranium fuels are complicated by the corrosive nature of these molten metal systems at 1700°C. Separations research pointed toward the removal of fission products from irradiated alloys has included a frozen salt-bed technique which minimizes container reaction with molten metal. The procedure consists of high-frequency induction melting of the metal sample which is supported by a vertical column of unmelted salt. The molten alloy melts its immediate salt environment and as it slowly falls down through the column, many of the fission-product poisons are transferred into the fused salt environment. The molten salt-metal zone is encompassed at all times by unmelted salt, preventing container contact. EXPERIMENTAL Experimental methods were separated into three parts: salt-bed preparation, melting, and analytical evaluation. A) Bed Preparation—The procedure for casting calcium-fluoride briquettes was to compress the powdered salt at 5,000 to 10,000 psi and place this compact in a graphite crucible. This assembly was inserted into a vacuum system and surrounded by an alumina crucible as well as molybdenum, tantalum, or stainless-steel foil thermal-radiation shields. The pressure was reduced and the crucible heated under vacuum to about 800°C with the fore pump operating. Argon was then admitted to about 0.8 atm and heating continued until the CaF2 had melted 5 min at the melting point seemed satisfactory). Apparatus used included a 1-in. graphite crucible with 1/8-in. walls, 1-in. ID in a 2-in. induction coil, and a 6-kw Ajax high-frequency converter. B) Melting—Calcium-fluoride briquettes, 1 in. in diam and 1/2 to 1 in. thick, were prepared and vertically stacked to obtain the desired column length. An irradiated alloy sample (nut = 10") was placed on top of the salt column and the assembly was connected to the vacuum system. After evacuation of 5 to 10 , purified argon was admitted and the system flushed twice. The final argon pressure was about 0.8 atm. The sample was heated by induction at a power of about 6.5 kw. It then melted its way down through the salt and freely dropped into a small alumina crucible. The molten metal is followed during its downward course by the induction coil which is mounted upon a power-driven machine-threaded shaft. Experimental conditions used in the foregoing work

Jan 1, 1960

By L. S. McNickle

[Commonly accepted maintenance methods are being outdated by the rapid acceptance and use of more complicated hydraulic circuitry on modern mining equipment. It is no longer adequate to use the maintenance program to merely repair or sustain equipment operation. Ever increasing operating costs place a huge premium on lost production time. It has, therefore, placed the maintenance programs in the position of being required to alleviate equipment malfunctions on production shifts and still attain the maximum unit life from each component part.]

Jan 1, 1961