Search Documents

In March 1990, Heritage Mining conducted a 2000 line km high resolution aeromagnetic survey of all its prospects in the Coromandel Peninsula. One of the areas covered was the Onemana Peninsula, situated about 5 km north of Whangamata. Details of location and geology are given by Robson and Stevens (this volume).   The detailed helicopter-borne magnetic and radiometric survey over the Onemana area consisted of 163 line kmÆs of flying, and was carried out in order to assist in the definition of hydrothermal alteration and pre- or post- mineralisation structures. The line spacing chosen was 100 m, flown east-west, with a mean sensor terrain clearance of 80 m. Tie lines were flown north-south every kilometre for levelling purposes. The sensor was a Geoinstruments G-813 proton precession magnetometer in a towed bird, with data recorded using a Geoinstruments G-2000 acquisition system.   The Onemana alteration system is at the northern end of a major north-north east trending structural corridor defined by regional aeromagnetic surveys performed by AMOCO in 1980 (Rabone, 1991). T his structure hosts a number of other extinct hydrothermal systems including Karangahake and Golden Cross. In the Onemana contour plot the predominant north-northeast structures form the boundaries of a large area of subdued magnetism in the southern part of the surveyed area that is caused by intense hydrothermal alteration. This area is about 3.5 km long by 1 km or more wide and contains outcropping sinters and hydrothermal eruption breccias, as described in Robson and Stevens. A number of other structures transect this alteration zone, with strike directions ranging from northwest to north. A northwest feature notably truncates the zone to the south, while the northern end seems to be simi1arly bounded; however as data coverage ends at the coast, this feature is less conclusive.    Two distinctive types of strongly magnetic rock were discernible the contoured data. The strong negative magnetic anomalies the north and west are caused by fresh negatively magnetised rhyolites. This was confirmed by ground follow-up work that showed the rocks to be fresh biotite rhyolites with high magnetic susceptibilities.

Jan 1, 1991

By Syd S. Peng

Coal mine ground control is the science of the application of rock mechanics principles to coal mining operations. More acceptance of ground control techniques by the US coal mining industry has been seen in the 1980s. It has been demonstrated many times that a proper ground control design is key to a successful coal mining operation. However, numerous in-mine applications of various ground control techniques by the author indicate that cur¬rent techniques need improvement. The biggest problem in coal mine ground control is that miners are dealing with materials of rapidly varying properties and occurrence. And only the exposed surface can be identified positively. Thus, in attempting to solve the ground control problems, many unknown factors are assumed. Some of these problems deriving from such assumptions are discussed here. Coal pillars There are two types of coal pillars - barrier and chain pillars - depending on the purpose. Barrier pillars are those located between panels or sections or mines. Their objective is to isolate the mined-out effects of one from the other. Chain pillars are characteristic of room-and-pillar mining. They are designed to support the overburden load and protect the surrounding entries and crosscuts. Pillar design is the most popular and, frequently, the only ground control technique employed by coal operators for mine design. There are many pillar design formulae available (Bieniawski, 1983; Peng, 1986). Nearly all consider both size and width/height effects. Specifically, pillar strength decreases with increases in pillar size and increases with increase in the ratio of width to height. However, the manner of those changes varies with investigators. Consequently, the pillar size determined varies considerably from investigator to investigator. And the variation grows much more pronounced as the seam depth increases (Fig. 1). The question, then, is which one should be used? One may say each formula is developed for a particular coalfield. A particular formula may have been used to design a pillar, which has not failed. Does that mean it was over designed? Not necessarily, because no one can confirm its stated "safety factor." Recent case studies (Peng, 1986; Tang and Peng, 1988) show that all pillar formulae are too conservative for chain pillar design in room-and-pillar mines due to the following two problems: • Uncertainty about in situ pillar strength. All formulae employ uniaxial compressive strength of selected samples tested in the laboratory and scaled to that for underground pillars. The scaling factors are not well proven. In situ testings by Bieniawski (1969) suggested that 1.5 m (5 ft) pillars are representative of in situ pillars that, after being tested in various US coal mines, are not universally applicable. • Uncertainty about the actual loading on the pillar. The most frequently used tributary loading theory defines the loading as total overburden weight tributary to each pillar (from roofline to surface). This is too conservative when it applies to coal measure rocks. The overburden consists of layered strata of different stiffness. Many stiffer strata will self-support over small roof spans. Depending on the location of these strata above the coal seam, it will reduce pillar loading in various proportions. It follows that total structural analysis using, for instance, finite element method is more appropriate. It can take into account the interaction of roof and floor strata with coal. This has been demonstrated by Peng et al. (1986,1988) on several case studies. However, the validity of the finite element structural analysis depends on the accuracy of in

Jan 1, 1989

By Sridhar Krishnan

This paper presents the results of a comprehensive pre-production pile testing programme for the US$ 800 million 1400MW Coal-Fired Jimah Power Plant Project in Negeri Sembilan, Malaysia. The testing programme included high-strain dynamic testing and fully instrumented static axial and lateral load testing of driven prestressed concrete piles and bored cast-in-place piles. A highlight of the testing programme was the pioneering use of the Global Strain Extensometer (GloStrExt) Method, a deformation monitoring system that uses advanced pneumatically- or hydraulically-anchored extensometers and a novel analytical technique to monitor loads and displacements down the shaft and at the toe of driven prestressed concrete piles. The experience with the testing programme for the Jimah Project also demonstrates the possibility of achieving notable breakthroughs, not only in the monitoring, evaluation and reporting of pile foundation behaviour dynamics but also in our understanding of the mechanisms that underpin such behaviour. These significant gains are undeniably a direct result of the committed and co-operative relationship among the project owner, design/builder, specialist piling subcontractors, pile suppliers and pile instrumentation and testing specialists.

Jan 1, 2006

By F. C. Canney

Geochemical prospecting seeks hidden mineral deposits by sampling for variations in the chemical composition of naturally occurring materials. Usually the samples are of soils and other products of weathering and erosion-surface materials extremely susceptible to contamination by human activities. Except when a survey is conducted well away from populated areas, contamination is an ever-present hazard. The program's success is particularly endangered when the contaminants are the elements sought; if these occur erratically throughout an area, spurious anomalies completely unrelated to mineralized areas can be formed. Evenly distributed contamination can be dangerous too, if it raises the background to such a level that true anomalies can no longer be easily detected. Suppose, for ex- ample, that in an area where the lead background is 20 parts per million the soil over a lead vein contains 1000 ppm of lead. Here the contrast would be 50 to 1, which is very satisfactory for geochemical surveying. Now if 1000 ppm of lead from some source were added evenly to the soil in this area, the contrast would be reduced to about 2 to 1, and the anomaly would no longer be readily detectable because a threshold of significance twice the value of the background is the minimum generally used for interpreting geochemical data.

Jan 2, 1959

A 3-D computerised model of the southern part of Greymouth Coal Limited's Coal Mining Licence area has recently been completed. This model, and associated 3-D CAD tools, has/is being used to optimise drillhole spacing during exploratory data collection and as a visualisation and interpretation aid. This model will also provide the basis for future mine planning, with the emphasis on an optimal mine outline to maximise safety and profitable coal extraction. Previous use of computer techniques was restricted to drillhole database entry, storage and log production. Recently a 3-D geological/structural model was created for the Southern Rapahoe Sector of the Greymouth Coalfield. Geostatistical analysis of the database highlights the inadequacy of the present drillhole spacing for preliminary mine planning. The sparsity of hard data at depth results in a lower level of confidence in the accuracy of the 3-D model. Nevertheless, the model and 3-D CAD techniques has been used to target and refine ongoing resource evaluation, and provides the basis for initial reserves. In the future the geologic model will be used as the basis for preliminary and later (optimal) mine planning. It is also expected to accommodate other forms of data input in seam drilling and seismic. Development of the 3-D computer model was a first in the Greymouth Coalfield and highlights both the use of computerised techniques for resource evaluation and mining, and the effects of wide spaced drillhole data on model accuracy. The computer will continue to provide the most efficient and cost effective tool for optimal resource evaluation and mine planning as Greymouth Coal Limited moves from feasibility/mine planning to full production. The increased use of computer-based methods for mine planning should be seen as part of 'The Changing Face of West Coast Mining' in line with the theme of this Conference.

Jan 1, 1996

By Johan Gjødvad, Catherine Aimone-Martin, Charles Dowding, Mathias Jern

A residential structure adjacent to a quarry in Ohio was instrumented to record structure motions, resulting wall strains and existing crack displacements in response to close-in blasting within 82 m (270 ft). The project is a cooperative effort among international experts representing the European Federation of Explosives Engineers (EFEE) and ISEE supported by more than 21 persons from eight different countries to compliment prior work performed at the Aitik Mine in northern Sweden. The focus of this study is to compare blast-induced vibration measurements relative to regulatory compliance limits as a percentage of allowable velocities among eight different countries for a one-story residential wood-frame structure with a brick-and-mortar exterior and full basement. Participating counties included Austria, France, Germany, Norway, Sweden, Switzerland, the United Kingdom (UK) and the United States (US). Geophones were placed on the foundation and in the ground in accordance with each country’s regulations to record peak velocities as a function of frequency or distance to blasting. This study extends the work performed at the Aitik Mine to include interior corner geophones to calculate global wall strains and micro-m (micro-in) displacement gauges mounted over an existing drywall crack to measure blast-induced dynamic crack responses and climatological influences on daily opening and closing of a crack. Structure responses were documented for 68 blasts conducted north of the structure from February through September 2023 of which 17 blasts were selected for detailed analyses. The highest in-ground PPVs recorded were 43 mm/s and 59 mm/s at the NE and SW corners, respectively. Measurements from these blasts plotted within each country’s limits provided a comparison of stringency among the counties. The percentage of compliance limits among counties ranged from an average of 114% for the US, UK, and Austria limits to the highest of 585% for Switzerland. Despite these high percentages of compliance for all countries, the global tensile strains induced by these blasts were at most only 12 μ-strains and occurred with the highest velocity blast that exceeded each county’s limit. This high percentage of compliance and low strain level demonstrates the restrictive nature of the regulations studied. Peak dynamic crack opening and closing during blasting averaged 20 -m (0.0008 in) while the 12-hour weather-induced crack displacement during the time period over which blasting occurred averaged 200 -m (0.008 in) and the largest 12-hr change in crack width was 356 -m. This low level of crack response validates the observation that the studied regulations have highly conservative limits for cracking potential of standard building materials.

Jan 21, 2025

By N McKay, J Vann, W Ware, P Hodkiewicz, C Morley

"Geometallurgy is now recognised within the mining industry as an approach that can both maximise value and reduce the risks associated with resource development. The process of spatial ore variability testing for metallurgical response and the use of quick, inexpensive metallurgical proxies has been well developed in the past decade in industry and the literature, and via various collaborative research programs and laboratories. Technology continues to advance with new techniques such as hand-held analytical tools and automated hyperspectral core scanning, allowing for even faster, less expensive in situ geometallurgical testing.In the current mining industry downturn, a critical frontier of geometallurgy is in its application in short-term geological modelling (ore control) and mine planning, and the associated decision-making. This is the end game at which the hard-won knowledge of orebody variability can be exploited to add near-term value. In order for spatial block models to be fit-for-purpose for such tactical uses, they must be populated with key geometallurgical information and then have workflows that use this richer model as a basis of material allocation to destinations so that the true value of the resource is realised.We envision geometallurgy (geomet) programs designed to add and sustain value at two levels:‘Strategic geomet’ has a long-term strategic focus that actively uses all relevant data that helps predict processing performance such as bench-scale metallurgical tests, mineralogy, geochemistry, ore texture etc (‘the geometallurgical database’) to model spatial ore variability and metallurgical response throughout the life-of-mine (LOM). This will enable better resource definition, more optimal mine planning and scheduling, improved process design and sustaining capital strategy over the LOM. The value-realisation is gained by basing all these strategic decisions on spatial models that better reflect the actual value of blocks (or aggregates of blocks) in the model.‘Tactical geomet’ has a short- to medium-term tactical focus that, again, actively uses the geometallurgical database, but also includes new data derived during ore control activities (such as drilling and sampling) to inform allocation-to-destination decisions via the ore control process. This will enable improved efficiency (ie less error) in allocation of mining blocks as direct feed, stockpile or waste. Importantly, this efficiency will be measured in terms of value and not grade, which is an incomplete – and typically biased – proxy for value. The key benefit is that ore control will then be planned and executed on the basis of realised value.We therefore propose a twofold systematic and holistic, value-based geometallurgical process. This process needs to be planned and implemented in an integrated manner, noting that strategic and tactical geometallurgy can be worked on by the same professionals, sharing data, methodologies and potentially models. What differs between the two levels is the required granularity, the business context and (critically) the decision-making time horizons.CITATION:McKay, N, Vann, J, Ware, W, Morley, C, Hodkiewicz, P, 2016. Strategic and Tactical Geometallurgy – a Systematic Process to Add and Sustain Resource Value, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 29–36 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories ; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgCO3) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1964

By Richard D. Luark, Fernanda S. Madrona

Designing temporary retaining systems that allow for deeper excavation amid the existing urban infrastructure has become a challenge. A 60-foot-deep excavation in downtown Seattle was required to construct five levels of below grade parking for a 35-story high-rise building, Tower 12, next to an existing 20-story tower with three levels of below grade parking, separated from the project by an 18-foot wide alley. The solution was to combine two temporary excavation support systems, soil nailing and anchored soldier piles, to work within the site constraints. Densely-arranged, short-length soil nails were used to support the upper 30 feet of the excavation, while the lower 30 feet of the excavation was supported with soldier piles combined with steeply-inclined, high-capacity ground anchors, which extended below the adjacent building foundations. The combined temporary support system eliminated the need for internal bracing, reducing construction cost and schedule. The performance of the combined soil nail and soldier pile system was monitored with an inclinometer and optical survey monitoring, which demonstrated the performance of the combined temporary support system. This paper provides a discussion of the advantages of combining different excavation systems and an analysis of movement monitoring data collected. SITE CONDITIONS AND PROJECT INFORMATION Tower 12 consists of a 0.45-acre development with 36-stories of mixed, residential and commercial use with four levels of below grade parking. The project site is bounded by the Cristalla Condominium to the north, Virginia street to the south, 2nd Avenue to the East, and an 18-foot wide private alley to the west. The One Pacific Tower Condominium, which has three levels of below grade parking, was located to the west across the alley. A site layout plan is presented as Figure 1. As shown in Figure 1, the construction of the west wall required a maximum 51-foot-deep excavation, from elevation (EL) 162 feet to EL 111 feet. Adjacent to the west wall, the existing alley grade varies from elevation 154 to 161 feet, leaving a narrow block of soil 18 feet wide and up to 42 feet high to be shored along the alley in order to reach the One Pacific Tower bottom of mat foundation at EL of about 120 feet. In addition to the existing One Pacific Tower Basement wall, site constraints included existing utilities along the alley such as an existing 4.5-feet wide by 7-feet high vault, with bottom at approximate EL 146 located 10 feet from the back face of the proposed Tower 12 basement wall.

Jan 1, 2019

By Charles Sabine

The 27,960-acre Newberry Mountains Wilderness Study Area (WSA) is located in the Mojave Desert, 17 miles east-southeast of Barstow. In 1983, the U.S. Bureau of Mines, in conjunction with the U.S. Geological Survey, investigated mineral resources of the area as part of the wilderness review process. The Newberry Mountains are underlain by Paleozoic metamorphic rocks, Mesozoic plutonic rocks, and Tertiary volcanic rocks. Eleven mines and prospects were examined. Of the seven sites within the WSA, only the Northrup Prospect is mineralized. Only a few tons of manganese-bearing rock, containing 49% manganese oxide (MnO), are exposed, but exploration may disclose larger deposits. The Azucar Mine, a past producer of gold, is the only site examined outside the area that appears mineralized. Sample data from quartz veins exposed at the surface do not indicate that resources are present; however, the occurrence could not be fully evaluated because underground workings were not accessible. Sand, gravel, and stone are plentiful in the WSA, but alternate sources outside the WSA are available.

Jan 1, 1985

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way 'to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgC03) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1951

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Knowing shear mechanism of discontinuities under monotonic and cyclic loading conditions is a key factor in stability analysis of rock slopes and rock foundations. In this paper, the effect of cyclic loads on the shear mechanism of joint asperities is described. For this purpose, a fresh tension-split joint from a granite block was used as a reference and thirty five mortar replicas were fabricated. Cyclic shear tests were conducted on replicas under low values of constant normal load (CNL) using a servo-controlled loading system. Tests were performed in two consecutive steps; load-controlled and then displacementcontrolled. In the load controlled part, after initial increase of shear stress to 0.25 MPa, the test was stopped for 2 minutes, then increased to 0.5 MPa, and finally decreased to 0.25 MPa. This process was repeated ten times. At the end, the test was continued up to 10 mm shear displacement under displacement-controlled loading in order to pass the peak shear strength and reach the residual strength. Characterizing joint surface and modeling of involved asperities during the tests was undertaken using a Matlab code developed with new mathematical expressions. The algorithm used in the code is based on three-dimensional coordinates of the scanned joints’ surfaces before and after the test. It was found that a high percentage of degradation happens during the first cycle of loading and during the other cycles, degradation occurs gradually. While comparing tests conducted in monotonic and cyclic loading conditions, it was observed that under low number of cycles, the pronounced mechanism is consolidation of the joint surfaces. This consolidation increases contact areas and, therefore, shear strength parameters.

Jan 1, 2015

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

By Ann L. Backstrom

The Apex Tunnel is part of the Southern Nevada Water Authority?s proposed Clark, Lincoln, and White Pine Counties Groundwater Development Project. The project is intended to develop unused Nevada groundwater for meeting the water needs of Southern Nevada and would involve over 322 km (200 mi) of water transmission facilities. The Apex Tunnel, as currently conceived by ongoing planning and environmental analyses, would extend 2804 m (9,200 ft) through a structurally complex terrain of Paleozoic carbonate rocks and younger basin fill deposits and will traverse both public and private lands. Several faults cross the tunnel study area, juxtaposing rocks of varying lithology and degree of folding, and creating intervals of differing rock conditions along the tunnel alignment. This paper discusses how the geotechnical program was developed to be flexible and allow for rapid implementation of revisions based on new knowledge that became available during program execution, resulting in more effective decision making and enhanced value from the geologic investigation during the planning phase of the project.

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By D. K. Caddel

Several problems exist with the present design of coveralls used by miners in low coal (seam height 48 inches or less). The back portion of the coveralls often tears when roof bolts or rough areas in the roof are hit. Movement in the shoulder area is restricted. Female low coal miners find it difficult to purchase coveralls that fit properly, and must remove both their hard hat and safety belt in order to urinate and defecate. The objective of this research was to design coveralls which would alleviate these problems. The following features were incorporated into the coveralls; padding in the upper back area to avoid tearing, an action pleat in the shoulders to increase mobility, an inseam zipper to more easily allow miners to perform their bodily functions, and reflective tape to increase visibi¬lity of the miner. A heavyweight denim fabric was used to increase warmth and durability of the coveralls. The coveralls were assessed K long four parameters (comfort, safety, worker productivity, and fabric suitability) using both an in-field assessment by low coal miners and simulation studies. The experimental coveralls proved superior to conventional coveralls along all four parameters. Work clothing sizes for female miners were developed.

Jan 1, 1982

By A. Ligorio Pires de Carvalho

The main potash deposit at Taquari-Vassouras is contained in cycle VII, and consists of several sylvinite bodies. Cycle VII belongs to a sequence of nine cycles defined by Szatmari (1974) in the Sergipe-Alagoas basin. The sylvinite layers are separated by halite beds. They are seated on or may be laterally in discordant contact with other lithologies such as the tachyhydrites at the base, and the limestone breccia at the top. The main structural features in the deposit include numerous synclines and anticlines, salt dissolution phenomena, and open fractures associated with the axes of the anticlines.

Jan 1, 1995

By D. J. Collins

While the charcoal in pulp (CIP) process was introduced to the mining industry many years earlier, it did not gain widespread recognition until 1973 when Homes take Mining Company installed a CIP circuit at their Lead, South Dakota plant. Since then, a number of mills have been put into production which utilizes activated charcoal for the recovery of precious metals. One of these plants was the Jerritt Canyon mill which Freeport Gold Company commissioned in 1981. It was during the time that the author was employed by Freeport Gold Company that the ideas and concepts presented in this paper were formulated.

Jan 1, 1989

The physical setting and background to mining operations on Misima Island and the overall plant lay-out are outlined. Developments and changes made to each section of the plant are described as they were encountered during commissioning and initial operation.

Jan 1, 1991

By John G. Parker

Important quantities of gold, silver, platinum-group metals, selenium, tellurium, and arsenic are recovered in the processing of copper concentrates. The objective of this Bureau of Mines study was to determine the occurrence of these elements in copper ores and to trace their distribution during subsequent processing steps. The study describes the important areas supplying concentrates, precipitates, and unrefined copper to the copper smelting and refining industry in a composite of the years 1971-74. The relative importance of these areas as a source of the respective byproducts is assessed. The lack of certain quantitative and assay data, recycling of dusts and slags, and the addition of scrap to the feed often complicates calculations and estimations of the byproducts in the smelter-refinery throughputs. Such volatile or low-boiling point elements as arsenic, selenium, and tellurium may be lost in gaseous and other emissions in various processing stages, or they may be concentrated in slags and residues for which samples were not available. The effects of antipollution legislation to improve control of sulfurous and other emissions that may affect recovery of certain byproducts was noted. A section on newer technology illustrating hydro-metallurgical techniques that may affect the recovery of minor metals is included.

Jan 1, 1978