Search Documents

By P. Rusin

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environ-mentally unacceptable. Bio-reductive leaching of such ore samples at MBX resulted in high recoveries of silver and molybdenum. When baseline 3-day cyanide bottle roll tests were conducted on manganiferous oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bio-reduction with 99.8% dissolution of manganese. A follow-up cyanide bottle roll test yielded an additional 8.5% silver recovery for a total recovery of 94.5%. Baseline 3-day acid bottle roll tests of the iron oxide molybdenum ore yielded 1.8% moly. However, bio-reduction solubilized 93.3% of the moly into the growth medium. An additional 0.3% moly was recovered during the follow-up acid bottle roll test. Microbial treatment of refractory oxide ores with bio-reductive bacteria resulted in higher recoveries of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and moly was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1992

By M. Z. Emad, M. U. Khan

"Coal mines opting for longwall mining or its variations rely on the main and tail gates for production. Stability of these entries or crosscuts is crucial in coal mining operations. Roof or strata failure can be fatal, may lead to property loss and delay in production. Failure of the gates depends upon many factors including the mining method, panel dimensions, pillar width, mine depth, caving rate, dimensions of gates and roof strength properties. In Pakistan coal is mined through a variation of longwall mining method with almost no mechanization while using timber as a primary support. Timber support as chock is very useful in coal mines especially in overhanging face. Similarly gate entries and coal faces are supported by chock supports throughout their length. In this paper the stability of the longwall gate is assessed for a typical coal mine in Pakistan by using finite element code. Numerical modelling considerations for gate entries are discussed. A model parametric study is performed for key factors. The results showed that the existing mining practice is not suitable and there is a need to review the mining approach. INTRODUCTION Main and tail gate entries leading to longwall mining panel play a crucial role in production cycle. Failure of any of these may lead to loss of life, property and production delays. The stability of gate entries depends primarily on the nature of loading and stresses incurred. It is relatively easier to assess the ground response to production for common longwall mining panel. In thin-seam coal mines the gate entries are generally supported throughout their length by timber made chock supports. The tailgates receive huge deformations and stresses during the mining and backfilling cycle. The chock supports are required to take care of rock falls leading to blockage of entries causing production delays and loss of capital. A number of supports are available for supporting the gate entries (Hoek and Brown 1980; Brady and Brown 1985). The support system can be selected based on load-deformation characteristics including the yielding behavior, pre- and post-yielding behavior (Barczak, 2003). The principal of support selection is that the support characteristics must match the ground response in order to maintain the gate entries (Mucho, et al., 1999). It has been observed that thin-seam mining (<1 m) is very challenging and it is necessary to develop an understanding of ground mechanics before the selection of an efficient support system Dolinar (2003). The chock supports have been tested for load-deformation characteristics in the laboratory (Barczak 2003). But the ground and support interaction, response and loads must be assessed for individual site. This can be accomplished by in-situ testing and observations at few locations. The generated data is generally insufficient for complete understanding. Numerical models can combine the data generated in the laboratory and on-site to fulfill the requirements."

Jan 1, 2017

By J. F. Archibald

This paper reviews the formation of the Canadian Mining Education Council (CMEC) and its terms of reference. CMEC considers that Canada?s mining schools represent a distinct competitive advantage to the Canadian Mining Industry. The core objective of CMEC is to reinforce the links between the constituent schools and their individual Industry Advisory Committees. The latter traditionally provide the schools with a great deal of guidance on a range of planning issues, including recruitment, curriculum, research and infrastructure. Beyond those bounds CMEC intends to improve its ability to network with the industry and government. It is concerned overall with the objective to raise the quality and level of its educational and research contributions to meet the needs of industry and society.

May 1, 2002

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By Armine F. Banfield

Selection of a plant site is becoming increasingly more difficult and important, mainly due to advances in technology, antipollution laws and changing economic, social and community conditions. Discussion falls naturally under three headings: economic considerations, terrain considerations and environmental considerations. Aside from acquisition of surface rights, problems having to do with terrain, or topography, usually can be dealt with by management alone. Economic considerations largely involve decision-making by management plus negotiations with government regulatory agencies acting under set rules. Environmental considerations, such as air and water pollution, townsites, housing, schools, noise abatement, appearance, surface rehabilitation and the like usually are under the control of federal, state or municipal bodies with a large degree of decision-making. Successful solution of environmental problems often requires lengthy negotiations, during which public relations by the mining company play an important part. Existing union regulations or customs may confine decision- making and the establishment of wage rates, working conditions and regulations. These usually require considerable planning and negotiation. Initial production often is delayed by formal negotiations involving environmental considerations. Surface facilities usually can be divided into two broad categories: those for concentrating ores--such as gold, silver, base metals, low-grade iron ore and potash-which should be close to the mine to reduce ore-transportation costs to a minimum, and those where the ore is shipped elsewhere for treatment, such as direct-shipping iron ores, complex high-value ores requiring specialized treatment and ores from which special products are derived for local markets. The long-term aspects of plant-site selection too often are given no or insufficient consideration because of immediate financial limitations. As a result, additional capital expenditures may be required later for relocation of townsites, roads, railroads and plants to provide additional room for extension of open-pit operations, tailings disposal, storage, or danger to foundations through underground subsidence or open-pit mining. In the past, hillside sites for concentrating plants were preferred to take advantage of gravity-feed methods The modern trend, however, is to place as much equipment as possible on approximately the same level. Some costs relating to plant sites are included in this section. They are ranges as of the year 1970, and are offered only as general guides. Such costs will vary widely with geographical location and, of course, are subject to escalation due to increases in wage rates and cost of materials. Items in the bibliography contain more detailed and comprehensive data on specific subjects. Most contain bibliographies of their own.

Jan 1, 1973

By R. E. Tate, L. J. Herman

We have had occasion to produce wire of Np-237 in small diameters for use in some chemical experiments. Since the mechanical metallurgy of neptunium has not been investigated extensively, it seems desirable to report our successful extrusion technique. Because of the neptunium activity and its attendant health hazard the experimental work was done in glove boxes and related equipment also used for Pu-239. At room temperature a phase neptunium&apos; is a hard (Dph -355) orthorhombic metal of high density (p = 20.45 g per cu cm). a neptunium transforms2 to tetragonal ß neptunium at about 280°C and this in turn transforms to bcc y neptunium at about 577°C. The y phase melts at about 637°C. A temperature of 340° to 345°C was selected for the extrusion, this temperature being a compromise be- tween a possible advantage of working with the presumably more plastic cubic y phase above 577°C and the risk of having the neptunium react with the alloy steel die to form the low-melting Fe-Np eutectic. A 0.75-in.-long, 0.26-in.-diameter ingot of good-purity* Np-237 was extruded by the direct *C = 230 ppm, Pu = 200 ppm, thirty-five metallic elements below limit of detection by spectrographic methods. process through flat-face orifices to form several sizes of wire ranging from 0.010 to 0.030 in. in diameter. Molybdenum disulfide was used as the die lubricant. The extrusion was done in a vacuum of about 10-4 torr to reduce reaction of the neptunium with atmospheric gases. British workers3 at Harwell have extruded neptunium under similar conditions. The force required to extrude 0.010-in.-diameter wire at the rate of 4 in. per min was 6000 lb, as measured with an electrical load cell. Wire 0.020 in. in diameter was extruded with a force of 4700 lb at a rate of 2 in. per min, and wire 0.030 in. in diameter was extruded with a force of 4000 lb at a rate of 1.3 in. per min. An extrusion constant, c, can be computed from the measured forces, P, for the equation4 P = c log-A/a where A/a is the extrusion ratio or the ratio of the cross-sectional areas of the container and the

Jan 1, 1965

By M P. Cipold, J F. Bachmann, C C. Bachmann, J Ha

Knowledge of fuel qualities is of ultimate importance for the efficiency of chemical plants or power stations. Although most blending yards are equipped with automatic samplers and the derived samples are processed in the laboratory, the quality variation of the blended product may still be strong. This is caused by several reasons. First of all the process of sampling, crushing, dividing and analysis is time consuming. Results are available only with a delay of two to 24 hours. During this time blending is operated without knowledge of the main parameters. Conveyors with high throughput require expensive sampling systems capable of handling samples which are representative. The frequency of sampling needs also to be high in order to be representative. This results in high maintenance costs and also downtime of the sampling system.Online analysis of bulk materials has matured over time and today it can supplement but not replace laboratory analysis. As an example, J&amp;C Bachmann has realised a coal quality monitoring system on the coal supply of a South African coal processing plant. The plant consumes ~42 Mt of coal per annum. The blending yard consists of two sets of three heaps where coal of six different mines is blended according to the factory’s requirement. From there, the blended coal is fed to the factory on two different belts.In 2010 the plant installed a TEXAS X-ray fluorescence analyser as a trial. It was tested under different conditions on several belts before the customer decided to install six TEXAS analysers on the feed belts to the stackers and two more analysers on the reclaimer belts. All analysers are installed directly on the belt and not on a substream.During the test period blending strategies were developed in close cooperation between the customer and J&amp;C Bachmann. The use of the analysers in conjunction with the blending model has proven that the variation of the reclaimed coal quality was decreased significantly, which results in increased process performance and significant cost savings.CITATION:Bachmann, C C, Bachmann, J F, Cipold, M P and Ha, J, 2017. Online quality control of a coal blending yard, in Proceedings Eighth World Conference on Sampling and Blending , pp 125–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By Haydn H. Murray, Sam H. Patterson

The term "clay" is somewhat ambiguous un¬less specifically defined, because it is used in three ways: (1) as a diverse group of fine-¬grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term "clay" realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define be¬cause of the wide variety of materials that com¬pose it; therefore, the definition must be gen¬eral. Clay is a natural earthy, fine-grained ma¬terial composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many defini¬tions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales, Soil investigators and mineralogists gen¬erally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than ap¬proximately 4 micrometers. Some authorities find it convenient to use the term "clay" for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or ar¬gillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally un¬derstood by those who use it. Clay is an abun¬dant natural raw material, and it has an amaz¬ing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial min¬erals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1970, 1971, and 1972 production and values according to the U.S. Bureau of Mines (Ampian, 1972). Adequate reliable statistical data on which to summarize world production of clay are un¬available; this paragraph outlines the world re¬quirements for clay only in a very general way. According to one estimate, the world bentonite production in 1972 was 3.5 million tons (Anon., 1973a), but in the authors&apos; opinion it was prob¬ably at least 5 million tons. The total fuller&apos;s earth produced was at least 1.5 million tons and may have been as much as 2 million tons. The total world kaolin production in 1972 was more than 10 million tons. Approximately 7 million tons of this total was produced in only two regions-the Georgia-South Carolina kaolin belt in the United States and the Cornwall re¬gion, United Kingdom. The world&apos;s 1972 out¬put of ball clay, which is also produced pri¬marily in the United States and the United Kingdom, was approximately 1.5 million tons or perhaps a little more. The total world fire clay production in 1972 was probably about one and one-half to two times and the miscellaneous clay production three times the United States production. As industrial minerals, clays are a complex group that consists of several mineral commodi¬ties, each having somewhat different mineral¬ogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized

Jan 1, 1975

By H. C. Rickaby

Introduction The township of Swayze, from which the Swayze gold area derives its name, is in the Sudbury mining division, approximately 150 miles northwest of Sudbury. The gold area may be regarded as situated at the southwest corner of a triangular area whose northeast and southeast corners are at Porcupine and Shiningtree, respectively, and whose sides are between 70 miles and 90 miles in length. On a geological map, it would be found that belts of Keewatin greenstones and sediments form the sides of this triangle, and that they surround a large granite mass. Prior to the summer of 1931 the Swayze corner of this triangle had probably been less prospected than the other parts and comparatively little was known of it from the standpoint of gold mining possibilities. The extensive belts of iron formation to the south and west of Swayze received some attention about the year 1909, and during the years 1927 and 1928 some prospecting was done in the townships of Greenlaw and Cunningham, south of Swayze, but chiefly for base-metals- copper, zinc, and lead. In the summer of 1931 a very promising discovery of gold-bearing quartz was made by J. G. and J. L. Kenty, working for the Brett-Trethewey Mines, Ltd., in association with Northern Canada Mining Corporation, and Northland Prospectors, Ltd., and this property, now known as the Kenty Gold Mines, Ltd., has been actively developed with very encouraging results. Following this discovery a6d during the summer of 1932 much prospecting took place in the area, as a result of which a number of other discoveries of gold were made, chiefly to the west of the original find. They are distributed over a wide area, which includes the townships of Rollo, Raney, Swayze, Denyes, Halcrow, and Greenlaw.

Jan 1, 1933

By E. R. Maize

[In %-port of Invcstiptionn 7452 ,g dcniing with roof ~wet,ent in the Cmcibla r~ine, rof&apos;erence .,as m.da to the f~ct tiwt timker decny war, bsing studied at tho tine of writing. Thic napor, written a3er completion of that ~tudy, describ~s t1l.e ~mrl&apos;: and sunlharizea the fiats obtained. Ifhen tlle stu* oi roof novement bras be,- at Cxcible tw igeas \%.ere a6-r;incsd. on decay of tiriber Q: scne of :he olficialr;: (I.) 9:la.t timber decay v:as unustmlly rapid in ,tho Ciuoiblc mins, ,m?. ((2) that timber coated with rock ri..~st deixiyad morrl mpirlly thnn those %hat vsrc not so coated. Thsx ::ore no records by which tkeso &apos;iaeas could &apos;L;e tertcc?, ard it cnpsarefi vise to make a limite6 in- vo3tiption, p~.rticu!.ai.ly of +.he effect of roc!< dusting on decny, as rock ductirg is nn importnnt mer-ns of ~rc-,rcnt?;~g cad-dust eql-osions. ]

Jan 1, 1941

By Mustafa Kumral

Monte ? Carlo simulation is often used to assess the risks associated with uncertain variables in mining operations. The success of Monte-Carlo simulations depends upon reproducing the dependencies among variables to some extent. However, some variables may exhibit different dependency patterns. In these cases, classical techniques for dependency quantification cannot capture dependencies. As an alternative, the copulas allow modeling nonlinear dependencies. Furthermore, any choice of marginal distributions can be used. Especially, for the data, which is sensitive to extreme case such as financial crisis, the copulas arise as a means to reproduce the correlations among variables. In this paper, the copulas are introduced to mining practitioners using Monte-Carlo simulations for risk assessment. Then, a case study is given to show the superiority of the copulas over classical techniques using ModelRisk Software. In conclusion, it was observed that the copulas enhance the quality of Monte-Carlo simulations by capturing variable dependencies.

Aug 1, 2013

By Mani Manimaran, Inna Dymov, Mariam Melashvili, Chris Fleming, Joe O’Day

This paper presents experimental evidence that supports the use of bromine/bromide as a potential alternative to conventional cyanidation for gold leaching. The study evaluated a brominebased lixiviant, Stabilized Bromine, with considerably lower vapour pressure than liquid bromine. Using a rotating device, the rate of gold dissolution was determined at various concentrations of this reagent. The reactivity of pure pyrite, arsenopyrite and chalcopyrite minerals was also evaluated in stabilized bromine reagent. Furthermore, bromine leaching of gold in a number of gold bearing ores was undertaken. Results showed that significantly higher gold recovery can be achieved with bromine than with cyanide when leaching gold encapsulated in sulphides, but bromine consumption was high owing to simultaneous oxidation of the sulphides. The greatest promise for the bromine leach process was with oxidized gold ores. The recovery of gold from oxide ores with bromine was comparable to that achievable with cyanide and bromine consumption was reasonable when leaching was conducted at a near neutral pH of ~6. In the case of oxidized gold ores containing copper mineralization, it is possible that bromine consumption may be lower than cyanide consumption, since there is evidence to suggest that bromine is less reactive than cyanide with copper minerals.

Jan 1, 2014

By E. Buehler, H. J. Levinstein

The temperature ranges in which the three inter-metallic phases in the Nb-Sn system form have been determined and the composition and structure of two of the three phases has been established. The kinetics of the formation of Nb3Sn in cored wire samples has been studied in the temperature range of 800° to 1050°C. From 800°to 950°C the rate of formation increases by four orders of magnitude. The rate-controlling step for the formation process in this temperature range appears to be the diffilsion of tin through NbSn. At higher temperatu~es a change occurs in the mechanism of the formation process such that up to a temperature of 1050°C the rate of formation of Nb3Sn does not increase above the rate observed at 950°C. For temperatures helow 950°C the current-carrying capacity of the wire increases with increased percent reaction reaching a maximum value when the formation process is 90 to 95 pct complete. The maximum current-carrying capacity obtainable in this temperature range is independent of the temperature. Above 950°C tlze current-carrying capacity obtainable in the wire decreases with increasing temperature of formation. A model is proposed which accounts for the ohserved behavior. RECENTLY, Buehler et a1.l reported the results of an investigation of the process variables which influence the superconducting properties of Nb3Sn-cored wire. These results indicated that at least four variables affect the properties of the manufactured wire. These include composition, particle size of the starting powder mix, temperature of heat treatment, and time of heat treatment. In order to understand completely the role of these variables, it is necessary to have an accurate knowledge of the phase equilibria in the Nb-Sn system. At the present time, phase-equilibrium diagrams for the Nb-Sn system have been published by a number of investigators.2-5 The diagrams differ as to the number of phases present, the composition of the phases, and the temperature range of stability of the phases. The present investigation was undertaken in order to resolve these differences. Since the investigation of Buehler et al. demon- strated that the length of time at the temperature of heat treatment affected the superconducting properties of Nb3Sn, it is apparent that it is necessary to understand the kinetics of the formation process as well as the equilibrium conditions before a complete understanding of the system is possible. As a result, the kinetics of formation of the various phases in the system were also studied in this investigation. EXPEFUMENTAL PROCEDURE Diffusion couples and sintered powdered compacts were employed in the phase-diagram investigation. The diffusion couples were made by filling 1/8-in.-ID monel-sheathed niobium tubes with tin. The monel sheath was employed to facilitate drawing.&apos; The tubes were then drawn to a tin-core diameter of 32 mils. Samples approximately 3 in. long were then cut from the drawn composite. The tin was drilled out of the ends to a depth of 1/4 in. and niobium-wire plugs were inserted into the ends and peened over. The monel was removed by etching in concentrated nitric acid, after which the samples were sealed in evacuated quartz bulbs and heat-treated in a resistance-wound tube furnace. The samples were quenched into ice water upon removal from the furnace. The diffusion couple samples were examined metallographically employing a chemical etching solution consisting of 10 ml of saturated chromic acid per g of NaF. In addition, two anodizing solutions were used for phase-identification purposes. The first was the picklesimer7 solution; the second consisted of equal parts by volume of 30 pct H2O2 and concentrated NH4OH to which 1 g of NaF was added per 25 ml of solution. The anodizing conditions for the second solution were 2 v and 100 ma with a tin cathode. The powdered compacts were made by pressing previously mixed powders of 99.9 pct pure Sn and 99.6 pct pure Nb supplied by the United Mineral Co. into cylinders 3/8 in. in diameter by 1/2 in. long. The cylinders were then sealed in quartz tubes and heat-treated in the same manner as the diffusion couples. The samples were examined metallographically and by X-ray diffraction techniques. Since it was desirable to be able to correlate the kinetic data with current-carrying capacity, the type of specimen chosen for this part of the investigation had to be a compromise between the optimum system for studying kinetics and one which was suitable for making current-carrying capacity

Jan 1, 1964

A nuclear technique utilising the gamma-ray resonance scattering process is used at Isa Mine for the determination of copper in drill core and bulk mineral samples. The Copper Bulk Analyser (CBA) provides quick and accurate non-destructive copper analysis of drill core at costs two to three times cheaper than conventional chemical techniques.The almost immediate availability of sample results enhances the efficiency of the mine geologist in the duties of grade control, design of diamond drilling programmes, and input to planning. The unit has proven to be a reliable and accurate production tool requiring a minimum of technical support.

Jan 1, 1990

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

By Subrata Roy

The slag produced in metallurgical smelting processes contains considerable amount of valuable metals. The present work focuses on recovery of copper value by froth flotation from the copper smelter slag. The slag samples are subjected to detailed characterization including automated quantitative mineralogy using Mineral Liberation Analyzer (MLA). The MLA results indicate that a part of copper is present in sulphide form in fayalite (iron-silicate) matrix and very poorly liberated. SEM-EDX analyses also reveal that a certain part of the copper is present within the fayalite (Fe-Ca-Si) matrix, perhaps either as lattice impurity or very fine grain. The copper smelter slag is ground in wet mode in a ball mill, to particle size distribution suitable for flotation. Subsequently, the slurry undergoes froth-flotation in lab-scale Denver-type flotation cell. Various combinations of sodium iso-propyl xanthate (SIPX) and alkyl hydroxamate collectors are used along with pine oil as frother. A multiple collector dosage is required for effective flotation of non-sulphide copper phases associated fayalite and alkyl hydroxamate is identified as one of the effective collector for non-sulphide minerals. The copper recovery can be enhanced by 7-10% with a combination of collectors as compared to conventional sulphide flotation using only xanthate type collectors. However, the grade decreases to some extent. Keywords: flotation, copper slag, hydroxamate collector

Sep 1, 2012

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020