Search Documents

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By James Barr

Geology and Mineralogy1 TENNESSEE phosphates are commercially divided into three varieties: Brown, blue and white. The first two only are now of commercial importance. The white phosphates of Perry county are not being mined at present owing to their pockety occurrence. The white phosphate is Fig. I.-DEPOSITS OF 75 PER CENT. BROWN PLATE ROCK UNDERLAIN BY SAND. the highest grade of the three varieties, running often more than 90 per cent. tricalcium phosphate. The brown rock is found in three varieties, grading from the dense almost vitreous gray rock, 76 to 82 per cent. tricalcium phosphate, down

Jan 9, 1914

By Tatiana Tronda

"The territory of Belarus is characterized by nonhomogeneous ground conditions. In some cases soft ground layers can reach tens of meters in depth. Application of piles and other conventional foundations is rather difficult and expensive in such complicated conditions. Alternatively for the first time dry concrete columns were applied to improve the saturated soft soils at two sites. As there is no design methods for calculation of bases improved by dry concrete columns static penetration and static load tests were carried out to check the bases on availability. Considerable increase of toe resistance and Young modulus was achieved for all types of soil. Practical application, technology and test results are described in the paper. According to comparative calculations the cost of foundations on the base improved by dry concrete columns can be 32-75% lower than the cost of conventional pile foundations depending on ground conditions.INTRODUCTIONPile foundations, sand cushions or dewatering are usually applied in complicated ground conditions which are caused by presence of saturated soft soils. If the depth of soft soils reaches 20 m or more, conventional foundations have limited application, high labor and construction cost. A rational solution in such conditions is a ground improvement of upper soft soils. It allows the loads to be transferred on upper ground layers and the stresses to be dissipated considerably before reaching underlying soft ground layers.One of the effective ground improvement methods for saturated soft soils is the reinforcing by dry concrete columns (Fig. 1). The method allows saturated soft soils to be compacted and be drained at the same time. As a result strength and deformation characteristics of natural soils improve (Tronda 2013, ?????? 2014).Unfortunately, there is no design and computing methods for the ground improvement by means of dry concrete columns. However, at present the methods are under development on the basis of theoretical and experimental researches.TECHNOLOGYThe dry concrete columns are fulfilled in pressed wells according to technology of vibrostamped piles. Wells are pressed by vibratory hammer with the closed ended casing (Fig. 2) that provides compaction of surrounding soft soils. Then the casing is filled with dry concrete mix (Fig. 3). The casing end remains on the design depth and the casing is removed by vibratory hammer. The removing of the casing with vibration enables compaction of dry concrete mix inside the well. Dry concrete mix drains surrounding saturated soft soils improving its properties and the compaction speeds up the consolidation process. Over time the dry concrete columns fasten absorbing water from surrounding saturated soft soils that is need for hydration of cement (Fig. 4, 5)."

Jan 1, 2016

By Cheryl L. Allen

Increasing energy costs associated with mining have become an issue that must be addressed by industry to ensure sustainable production. As underground mine ventilation systems account for 40% to 50% of a mine?s total energy requirement, initiatives to maximize their efficiency have been introduced worldwide. A control method known as Ventilation-On-Demand (VOD), which adjusts the ventilation system by responding to the activities of mine personnel and air quality, has been commissioned at Vale?s Coleman Mine. This initiative is an effort to reduce energy consumption, maximize efficiency of the ventilation system while ensuring air quality. There are five control strategies that can be executed with the VOD control system in place at Coleman Mine: Manual real time control Time-of-Day Scheduling Event-based control Environmental control Activity Based Control/Tagging This paper describes the system, control strategies and impact on energy consumption and flexibility of airflow distribution as applied at Vale?s Coleman Mine.

May 1, 2011

By Charles J. Kucera

Today's highly publicized issues of resource development and environmental protection are not new. But recently these issues have been played one against the other, and some would have us believe they are mutually exclusive. Why? Because modern man has realized that the shortest route to achieving economic progress is to subdue nature. He extracts mineral resources from the earth to provide the raw materials upon which other processes and services are based. But often in his search for economic progress he finds that other highly- held values (e.g., an unspoiled environment) have been violated. The natural response is a counter action - to attempt to protect nature. But this response is basically unsatisfactory because it is reactive.

Jan 1, 1979

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003

By Madgwick J. C

The monosaccharides glucose, galactose and arabinose, and the polyols glycerol and mannitol (0.1 Ufo WIV) supported pure and mixed culture heterotrophic bacterial manganese leaching of solid pyrolusite (MnO2, 2% W/V) to yield 14-38 mg/litre manganous ion in 3 days from a simple mineral salts media at 30°C. Supplementation of pure bacterial isolates growing on glucose with soluble intracellular photosynthate from freshwater algae (0.07 g/l carbohydrate) and marine algae (0.11 g/l) led to an improvement in Mn++ yields of 24 and 100 per cent respectively. Extracellular products of the freshwater algae (0.3 g/l carbohydrate) boosted recoveries by 57 per cent.

Jan 1, 1982

By James S. Browning

Research by the Bureau of Mines demonstrated that organic heavy liquid adhering to or adsorbed on fine mineral particles can be effectively removed by a novel method embracing pulping or displacement washing with hot water alone or in combination with a detergent. Displacement washing with steam alone or in combination with a detergent also was effective for removing the heavy liquid. In tests of sized minus 48-plus 200-mesh mineral charges, both the hot water washing with detergents and detergent steaming effectively reduced the heavy liquid losses on the particles to about 0.2 pound per ton of mineral or less. Centrifuging of the wash solutions permitted an almost complete recovery of heavy liquid from the solution as a pure heavy liquid product.

Jan 1, 1966

A research project was commissioned by the Australian Coal Association Research Program (ACARP) to improve the understanding of tailgate strata mechanics and to provide a more rigorous engineering basis for tailgate support design. A deformation mechanism termed æskew roofÆ was defined which relates the regional influence of differential horizontal strata movement (shear) about longwall extraction to gateroads. Confirmation of the mechanism was achieved by field investigations which included measurement of the shear displacement along weak interfaces. Under geological and mining conditions where the skew roof mechanism operated, strata units were found to move progressively further towards the goaf with height into the roof. 3D numerical modelling was used to assess the major geotechnical factors controlling the mechanism and to determine appropriate support strategies within a æskew roofÆ environment including the role of cables versus standing supports. The skew mechanism is considered relevant to; all roadways in the vicinity of longwall extraction including the faceline itself, chain pillar design, and support design.

Jan 1, 2005

Nowadays, the more successful plants are those who have adopted effective and efficient strategies to optimise their plant operation. As the ?heart of the plant? could be viewed as the mil-ling/grinding area, one of the key steps in plant optimisation is, therefore, ensuring the mill is operating properly. In the past, when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the semiau-togenous grinding (SAG) mill operation. As a result, mines have shifted their emphasis in optimization from ball mills to SAG mills. The grinding mill?s energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of pulp lifter being to transport the broken material and slurry out of the mill, its design optimization therefore affects the discharge capacity (or mill throughput) of AG and SAG grinding mills. This paper will discuss how the optimised design of the pulp lifter/ discharger has helped to eliminate material transport issues such as flow-back and carry-over of slurry and pebbles to in-crease the energy efficiency of SAG mill using the actual operational data.

Jan 1, 2014

By Douglas Bunting

(Wilkes-Barre Meeting, June, 1911.) WITH the gradual exhaustion of the upper veins in the anthracite coal-fields, the problem of mining at greater depths acquires increasing importance and demands the consideration of a number of important factors, one of which is the greater earth-pressure and the consequent necessity of stronger support o for the roof. Under the pillar-and-chamber system, almost exclusively followed in the Northern anthracite-field, the highest economy in mining is generally secured by leaving, on first mining, pillars only sufficient to support safely the overlying strata. As to the necessary size of such pillars, the opinions of mining experts are widely divergent. In establishing the width of chambers and pillars, the thickness of vein and its depth below the surface have received little consideration. For. instance, it has been quite usual to work both overlying and underlying veins with the same width of chambers and pillars, when the lower vein was two and one-half times as thick, and twice as fits below the surface, as the upper. In view of the generally-accepted theory that the crushing-strength of coal-pillars of the same base-area becomes less with increased height, it is probable, in this instance at least, that the most economical mining has not been secured. This question of adequate pillar-support is economically less important down to about 800 ft. than at greater depths; and it is with reference to mining at these greater depths that the study of the subject here presented has been prompted. The necessity of leaving larger pillars, involving greater mining-costs per ton and also smaller yields per acre, is one of the troubles of deep working. To mine without leaving adequate pillar-supports will result, sooner or later, in a squeeze. Limited areas, it is true, have been mined at certain widths of

Sep 1, 1911

By Arthur Brant

STEEPROCK LAKE (Figure 1) lies about two miles north of Atikokan, a village approximately one hundred and forty miles west of Fort William and one hundred miles east of Fort Frances on the Canadian National railway. The possible presence of hematite beneath the waters of Middle arm was inferred by early geological investigators (1890-1903) from the dense hematite float found on the southerly shores of this portion of the lake (1). A dip-needle survey of Middle arm, undertaken in the winter of 1930-31 by J. G. Cross, indicated two areas of high magnetic attraction which Mr. Cross thought might be due to magnetic iron oxides associated with possible hematite bodies. Bedrock could not be reached by the ineffectual hand-drilling so courageously attempted, and further work was abandoned. It was not until 1937 that Mr. Jos. Errington, of Toronto, convinced of the possibilities, determined to support Mr. Cross to the extent of several thousand feet of drilling. During the winter of 1937-38, holes Nos. 1, 3, 4, 5, and 13 were put down (see Figure 1). The first four of these holes demonstrated that the areas of magnetic attraction outlined by the dip-needle survey east of the Narrows and southwest of Elbow point were due to ash rock (2). As a result, Mr. Cross decided to investigate the bordering areas of low magnetic attraction and selected a location near the high ferruginous lime (3) point in the northeast of Middle arm. Dense, hard hematite beneath approximately 350 feet of water and clay was struck in the first hole, and, before the end of the winter's drilling, hematite had been encountered in holes Nos. 6 to 13 along a straight line 700 feet in length (see Figure 1). In the meantime, the Steerola ( 4) Exploration Company had been formed to continue development and already, in the spring of 1938, W. D. Neeland, the Company geologist, had come to the conclusion that the most probable location for possible hematite was at the ash-lime contact. Accordingly, during the summer, drilling was continued off-shore in holes Nos. 15, 25, and 27 (see Figure 2) toward possible hematite bodies inferred by Mr. Neeland.

Jan 1, 1940

Characterisation of Computer Printed Circuit Boards for Hazardous Properties and Beneficiation Studies

Sep 13, 2010

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined.1 Conductivity hard was 98.26 per cent. After a 10-min. heating at 200° C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. MATERIAL AND METHOD The work was done on high grade electrolytic copper, 99.942 per cent. copper-plus silver, silver 0.0008 per cent. It was hot-rolled to 3 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By A. Yehia

Fluoride activation has been evaluated by Hallimond-tube flotation of collophanite in terms of fluoride concentration, conditioning time, pH, and temperature. The results reveal that efficient oleate flotation of collophanite can be achieved by fluoride activation. Fluoride adsorption by collophanite as a function of fluoride concentration, temperature, pH, and crystal structure suggests that, at low fluoride concentration, a fluoroapatite-type compound may form on the collophanite surface by chemisorption of fluoride ions at calcium sites; at high fluoride concentration, calcium fluoride ap¬pears to form at the collophanite surface invovling a surface-precipitation phenomenon. The formation of CaF2 on the surface of fluoride-treated collophanite is further substantiated by the FTIR spectroscopic measurements, which clearly shows a metathetic exchange with phosphate from the collophanite lattice during surface precipitation process.

Jan 1, 1986

By H. J. Morel-Seytoux

Methods of predicting the influence of pattern geometry and mobility ratio on water flooding recovery predictions are discussed. Two methods of calculation are used separately or concurrently. The analytical method yields exact solutions in a convenient form for a unit mobility ratio piston-like displacement. A few typical pressure distributions, sweep efficiencies and oil recoveries are presented for various patterns. For non-unit mobility ratio, one may resort to a numerical method, such as that of Sheldon and Douherty. 1,2 Because the domains of applicability of the analytical and numerical techniques overlap, the exact solutions provide estimates of the errors in the numerical procedures. The advantages of the analytical and numerical methods can be combined. To develop a numerical technique as independent of geometry as possible, the physical space is transformed into a standard rectangle. The entire effect of geometry is rendered through one term, the "scale-factor", derived from mapping relations. The scale factor can be calcu-lated from the exact unit-mobility ratio solution for the particular pattern of interest. By this means recovery performances for arbitrary mobility ratio con be obtained for many patterns. A sample of tesults obtained in this manner is presented. INTRODUCTION Pattern geometry and mobility ratio are two major factors in making a waterflood recovery prediction. Because assisted recovery has become increasingly important to the oil industry, pattern configuration and mobility ratio also assume a greater significance in the assessment of the economic value of recovery projects. The influence of pattern geometry and mobility ratio in shaping a recovery curve and on the other quantities of interest to the reservoir engineer is the main subject of this paper. Much effort has already been spent on estimating quantitatively the influence of either pattern or mobility ratio or both on oil recovery. The literature reports many investigations of this nature. 3-9 However, many results or methods of recovery prediction presented in the literature cannot be considered fully satisfactory. Even for unit mobility ratio and piston-like displacement, where analytical solutions are available, the literature shows discrepancies. For non-unit mobility ratio, the divergence in the results is extreme. For infinite mobility ratio in a repeated five-spot, depending on the investigator, the sweep efficiency ranges from 0 per cent to 60 per cent. With respect to the influence of pattern on recovery, only the repeated five-spot has received much attention. Other confined patterns and pilot configurations have received very little attention. Two calculation methods are presented in this paper, either separately or concurrently: the analytical method of potential theory and the numerical method of finite-difference approximation. The analytical method is more restricted in scope than the finite-difference method, but it has the definite advantage of providing exact solutions within its range of applicability. If a unit-mobility ratio piston-like displacement is assumed, the analytical approach is possible. A few typical results are reported in this paper; the detailed description of the general method and of a great variety of results will be the subject of other articles. Fornon-unity mobility ratio, we must resort to a numerical scheme. The numerical technique is that which was described by Sheldon and Dougherty.l,2 It is not limited to piston-like displacement. However, mainly single interface results will be presented here. Because the respective domains of applicability of the analytical and the numerical method overlap, useful comparisons of exact and numerical solutions can be made for a variety of patterns. The advantages of the analytical and numerical approaches can be combined. The reason for the success of this analytical-numerical approach can be summarized in the following two points: 1. The numerical solution for arbitrary mobility ratio can be programmed most efficiently when the physical space in which the displacement actually takes place is transformed into a standard shape; and 2. This can be done with remarkable simplicity whenever an analytical expression for the pressure

Jan 1, 1966

By D. A. Harman

The U.S. Environmental Protection Agency recently recognized Newmont and other mining companies, along with the Nevada Division of Environmental Protection for their voluntary work in reducing mercury air emissions. One example of this voluntary effort is the installation of a reactive scrubber to capture mercury vapor from the exhaust of a carbon regeneration kiln at Newmont’s Twin Creeks Mine. After considering the available technologies, a proprietary reactive scrubber, developed by ADA Technologies, Inc., was selected and is currently being commissioned. Mercury removal rates greater than 90% have been documented.

Jan 1, 2004

By J. J. Kramer, G. W. Wiener, K. Foster

The effects of the primary grain size and sheet thickness on the secondary growth rates of grains with (100) surface planes were studied in 3 pct Si-Fe sheets. This secondary grain growth was carried out under conditions in which the {100} plane had the lowest surface free energy. The value of the surface energy difference, between the (100) plane and the random matrix planes was found to he only about 3 pct of the grain boundary energy, indicating that most of the driving force for secondary growth is supplzed by grain boundary energy. A method for obtaining cube texture in 3 pct Si-Fe sheets by a secondary recrystallization process has been reported.' It has been demonstrated that a difference in surface free energy between the (100) plane and other planes is responsible for this growth, where the (100) plane has the lowest surface energy. A semiquantitative relation has been derived for secondary grain growth in sheets where primary grain growth has proceeded until the grains have grown through the sheet and the average grain diameter in the plane of the sheet is from one to two times the sheet thickness. Then, the linear growth rate, G, for the secondary grains can be given by where M is the grain boundary mobility, is the grain boundary free energy, is the average primary grain radius, A is the average difference in surface free energy between the (100) plane and planes of other orientations, t is the sheet thickness, and C is a term first proposed by zener6 which acts as a negative driving force, the effect of inclusions in holding up grain boundary motion. Since the problem of grain growth being discussed is under conditions where the matrix grain size is at least equal to the sheet thickness, the radius r is, of course, a function of the sheet thickness. The term B/r is the grain boundary driving force normally associated with inclusion inhibited or texture inhibited secondary recrystallization. Here, however, the term is modified to account for the fact that growth occurs in thin sheets. The term is the additional driving force available because of the difference in surface free energy. The purpose of the present work has been to evaluate the driving force terms of the growth equation by studying growth rates of (100) secondary grains as a function of sheet thickness and primary grain size. From these data it has been possible to determine the relative values of grain boundary energy, surface energy difference, and the inclusion term, C. EXPERIMENTAL PROCEDURE A 3 pct Si-Fe alloy was melted and cast under a helium atmosphere using electrolytic iron and a pure commercial grade of silicon as raw materials. The alloy was hot and cold rolled to a thickness of 0.6 mm, and samples approximately 5 in. long by 1 1/4 in. wide were cut from the cold-rolled sheets. Four different primary grain sizes were obtained

Jan 1, 1963

By Cawte D. C, Just G. D, Whitchurch K. D

The stringent marketing specifications included in coal contracts mean that coal producers must supply cleaner and more consistent coal than may have been formerly required. Geostatistics has the potential to aid in the accurate estimation of the washability characteristics of coal. A prediction method, the Kriged Service Variable Approach has been developed.A Computer Aided Drafting and Design system has proved useful in the development and application of the approach. The geostatistical approach has been tested against coal geological and borehole data and applications discussed.

Jan 1, 1987

Typically, large volumes of data are collected during geotechnical investigations for mining projects but rarely is this done in a comprehensive manner that enables all aspects of the geotechnical environment to be evaluated. A geotechnical core logging process has been developed to record mechanical and structural properties of the rock mass. The method enables data for a wide range of rock properties and geotechnically significant major structures to be collected including rock strength, joint surface condition, fracture frequency and fracture orientation. The logging method is unique in that sufficient data is collected to enable the independent determination of all the major rock mass classification systems including rock mass rating (RMR), (Bieniawski 1976, 1989; Laubscher, 1990) Norwegian Geotechnical Institute (NGI) tunnelling quality index (Q) (Barton, Lien and Lunde, 1974) and geological strength index (GSI) (Hoek, Kaiser and Bawden, 1995). The logging system has been specifically developed to allow better and more precise appreciation of rock mass and structural conditions across the project area thereby optimising the use and application of the available geotechnical data and improving confidence in the outcomes of geotechnical investigations. This paper describes the core logging process with case examples showing how the logged data can be used for underground and open pit mine design.

Nov 25, 2010