Search Documents

By A. S. Yue

The movphology of the Mg-32 wt pct Al eutectic has been studied as a function of freezing- rate and temperature gradient. At slow freezing rates a lamellar eutectic was formed; whereas, a rod-like eutectic was generated at fast rates. The inter-lamellar spacing increased as the freezing rate decreased in aggreement with theoretical predictions. Lamellar faults, morphologically similar to edge dislocation models in crystals, were responsible for the subgrain structures in the eutectic mixture. A linear increase in fault density with freezing rate was observed. Fault concentl-ations of the order of 10 per sq cm for a range of freezing rates from 0.6 to -3.0 x 10 cm per sec were estimated. The transformation from lamella?, to rod-like morphologies was determined experimentally to be dependent on the freezing rate and independent of the temperature gradient. Moreover, the number of rods formed per- unit cross-sectional area increased exponentiallv with increasing freezing rote. BRADY' and portevin2 classified eutectic structures into lamellar, rod-like, and globular according to the morphology of the solid phases present. Although this classification is quite descriptive, very little has been reported on the details of the mechanism by which the eutectic structures are formed. Recent work by Winegard, Majka, Thall, and chalmers3 and by chalmers4 on lamellar eutectic solidification suggest that the maximum thickness of the lamellae decreases with increasing rate of solidification due to inadequate time for lateral diffusion. scheilS and Tiller' have shown theoretically that the lamellar widths indeed depend on the solidification rate. However, there has been no experimental evidence to support the theory. Chilten and winegard7 have studied the interface morphology of a eutectic alloy of zone-refined lead and tin. They found that the lamellar width decreased as the freezing rate increased in agreement with the theoretical predictions of scheils and Tiller.' More recently, Kraft and Albright' have investigated the microstructures of the A1-CuA12 eutectic as a function of growth variables. They observed lamellar faults present in the lamellar eutectic, similar to edge dislocation models in crystals. Furthermore, Kraft and Albright reported that they could not designate which extra lamellar was responsible for the formation of a lamellar fault even under electron microscopic magnification. In this paper, the morphology of the Mg-A1 eutectic structure is described. The effects of freez- ing rate on the interlamellar spacing and on the lamellar fault density are presented in detail. The transformation from lamellar to rod-like eutectics is discussed in terms of the freezing rate and the temperature gradient. EXPERIMENTAL PROCEDURE The experimental details of alloy preparation, the decanting mechanism and the determinations of the freezing rate and the temperature gradient have been reported elsewhere. Measurements of plate-edge angles were made with a microscope. The true angles used to determine the interlamellar spacings were determined by a two surface analysis technique.'' Since the decanted interface structure does not represent the true eutectic morphology on the solid,g all measurements were made from an area in the solidified bar behind the interface. Measurements of the apparent interlamellar spacings between the two phases of the eutectic were made on a photographic negative by means of a calibrated magnifier. Each value listed in Table I represents the average of thirty measurements on one negative. In general, these measurements are approximately equal with an error of less than pct. The average rod diameter for each specimen was also measured on a magnified photomicrograph. Each value of the diameter represents the average of fifty measurements. RESULTS AND DISCUSSION The experimental observations and their discussion to be presented here are restricted to the morphology of the eutectic structure and to the effects of the freezing rate and the temperature gradient on the solidification of eutectics. INTERLAMELLAR SPACING It has been shown previouslyg that the micro-structure of the decanted interface and the longitudinal section of the Mg-A1 eutectic is characterized by the presence of both lamellar and rod-like morphologies. The lamellae become more regular as the freezing rate is decreased. A three-dimensional photomicrograph representing a perfect lamellar morphology is illustrated in Fig. 1. The lamellae of the top and longitudinal sections of the specimen are regularly spaced while those in the transverse section are not quite straight and parallel. Their parallelism is slightly distorted because fault lines producing a discontinuity are present. A method for calculating the interlamellar spacings A, is described in Appendix 1. The true

Jan 1, 1962

By Laureano Rodríguez, Francisco Cuellar

El empleo de chimeneas de ventilación es un método ampliamente usado para aumentar y controlar el flujo de aire en las áreas de trabajo subterráneo. Sin embargo la eficiencia y seguridad asociadas a este método de ventilación dependen en gran medida del esmero que se tuvo durante la perforación y construcción de las mismas así como la forma interna y estado que tienen actualmente. Dados los requisitos actuales de aumento en la productividad y seguridad en las operaciones mineras del país, la empresa Tumi Robotics inició un proyecto de investigación y desarrollo de un sensor móvil que permita visualizar, diagnosticar y digitalizar el interior de chimeneas verticales de ventilación para minería subterránea.

Sep 29, 2023

By Marianne Snedeker

In January we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. At the same time we hired an outside firm, READEX Inc., of St. Paul, MN, to send the same questionnaire to a sampling of about 1000 US members, selected on an nth name basis, so that we could have some preliminary numbers for the Annual Meeting in February. READEX sent us the final results of its survey in March. At that time, 525 responses of the 992 surveys sent out had been returned, for a 52.9% response, an extraordinarily high return for a low-key (no incentive for return) random sampling. On May 7, we cut off on tabulating returns from the magazine so that we could report the results to you in this issue. At that time, we had 594 questionnaires returned. Our 594 and READEX's 525 (we have assumed that relatively few people returned both), represent a 1119 return, about 3.5% of the approximately 32,000 who received the January issue of ME. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded, told us something positive-you look at or read the magazine. Of the 1119 respondents, 1068 or 95.4% indicated that they had read or looked through the November and/or December issues. Those of you who refer to the magazine once are 466 or 42.6%. Those of you who refer to the magazine two or three times are 559 or 51.1%. Those of you who refer to the magazine four or more times are 68 or 6.2%. How much time do you spend reading the magazine? Of those responding to this question: 186 spent up to 1/2 hr 16.6% 590 spent up to 1 hr 52.7% 292 spent 1-2 hr 26.1% 51 spent more than 2 hr 4.6% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 764 or 69.4%, clip your magazine for further reference. Also, many of you, 513 or 64.2%, do not pass your copy on to another reader, indicating perhaps that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 2 people - 159 - 20.0% 3-5 people - 95 - 11.9% 5 or more - 31 - 3.9% Answers to what portions of the magazine you find useful indicated that the top three were Industry News, feature articles, and Technical Papers; see Table 1. The "other" category included advertising-display, classified, and employment-Coming Events, product information, Washington Survey, new books, the reader service card, and Engineering Fundamentals. Of those responding, 797 or 75.3% indicated a preference for dual notation of SI (metric) with English units; 228 or 21.5% preferred all SI units; while 34 or 3.2% preferred SI with dual notation of other metric units. Based on the preliminary numbers reported by READEX for this question, the MINING ENGINEERING Committee in February voted to return to a policy of dual notation. This decision has been implemented. We asked for your appraisal of the technical level of the magazine. Of those responding, 78 or 7.4% indicated it is too technical, 147 or 13.8% indicated it is not technical enough, and 836 or 78.8% judged it to have the correct tech¬nical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 32 said no, but an overwhelming 97% (1024) said yes. Of the specific topics, 785 like history, 558 political or socioeconomic articles, 440 career development, and 373 human interest. Other topics suggested included new disciplines, mineral resources of the world by

Jan 6, 1982

By S Hawker, M Gibbs, A Craven

Current climate change projections suggest both an increase in the intensity of significant rainfall events and an increase in the variability of rainfall in some regions of Australia. It is necessary for mine site owners and operators to understand the effects that this potential shift in climate may have on their operations. The ability to maintain compliance with discharge regulations and operational security for those sites that rely on surface water run-off harvesting may be negatively impacted if some current climate change projections are realised. Although current regulations require the preparation of water management plans, these are generally developed using historical climate records for the site in question and as such do not give any indication of a siteÆs resilience to the influences of climate change.This study compares design and operational considerations for a case study mine site using historical rainfall records and modified records representing climate change projections. The future climate models are invariably broad scale and are limited in their capacity to be downscaled to a reasonable resolution for developing a site water balance. Instead the local historical data set has been modified to concentrate precipitation to peak periods and propagated through the model. The study looks at the siteÆs response to the potential changes in climate.It is shown that if current climate change projections are realised, this will have a significant effect on both the necessary size of designed surface water infrastructure and operational considerations on-site. A discussion is presented on the potential risks that climate change presents to mine sites and the range of options that could be considered to mitigate these risks. Depending on a number of factors, including location and risk profile of the owner/operator, resilience to climate change can be addressed as either a capital or operational expenditure (CAPEX/OPEX).CITATION:Craven, A, Hawker, S and Gibbs, M, 2013. Site water balance response to variable climatic conditions, in Proceedings Water in Mining 2013 , pp 211-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By S. Steinlechner, S. Wegscheider

"In the past, the metallurgical industry was most of the time dedicated on their main commodity, recovering base metals like zinc, copper or lead but leaving other valuable side elements in the generated residues. As a result, these accompanying minor elements, like gold, silver, indium or also PGMs can be found in the dumps of the corresponding industry. Because of political unrest, strikes, economic reasons or decreasing primary resources leading to a high supply risk, also those mentioned minor elements moved into the focus of the recycling industry. Therefore, beside the base metals, first of all the recovery of those minor metals would be of high interest contributing to the economic viability of recycling processes, although they occur in much smaller quantities in materials. In this context, residues from zinc industry, like leaching residues or precipitation residues show high potential to carry silver as well as indium next to lead and zinc. Therefore, the paper summarizes carried out thermochemical calculations investigating a possible recovery of silver as well as indium by volatilization and the influence of zinc and lead on this process. Based on these theoretical investigations with HSC, trials in lab scale were done verifying the obtained results.INTRODUCTIONHuge amounts of iron precipitate, mainly jarosite get landfilled every year although there is a high content of valuable metals in this residue beside iron. Nevertheless, jarosite has to be dumped due to the presence of contaminating heavy metals. The accumulation of these residues takes up massive land on the one hand but also causes a series of environmental problems in ecosystems on the other. Moreover, some toxic ingredients such as arsenic and cadmium can be dissolved in rain water and are therefore harmful to the health of the aquatic systems. (Erdem & Özverdi, 2011; ÖzverdI & Erdem, 2010) Approximately 0.5 t of dry jarosite accumulate in the production of 1 t of zinc by the hydrometallurgical zinc-winning route (Svens, 2010). Jarosite is a precipitation residue formed during the iron removal. In general, the iron already exists in the zinc ore which is why zinc ferrite builds up during the roasting step of the zinc ore. Zinc ferrite is only soluble in strongly acidic solutions and during the hot acid leaching step it gets dissolved while zinc and iron enter the solution. It is necessary to get rid of the iron because otherwise it would deposit on the cathode first due to its precious character which would be harmful in the zinc-winning electrolysis. Nevertheless successful investigations were done by adding chlorine to the jarosite to recover silver. These findings leads to another residue which occurs in huge amounts – electric arc furnace dust (abbreviated with EAFD) from the iron and steel industry. In 2013 the annual electric steel production reached about 451 million tons. Around 15-20 kg of EAFD is produced per ton of steel in an electric arc furnace (EAF), creating approximately up to 9 million tons of dust per year. (Grabda, Oleszek, Shibata, & Nakamura, 2014; World Steel Association) Next to elements like zinc, lead and iron, chlorine and fluorine are present in this dust. While galvanized steel plates in the scrap act as a source for zinc, casting powders, flame retardants and synthetic coatings are responsible for the chlorine and fluorine contents in the dust."

Jan 1, 2016

By Garry M. Johnston, Matthew L. Sutcliffe, Nicholas J. Welham

"The predominant current processes for the treatment of oxidized copper–cobalt ores use a reductive acid leach to bring the desired metals into solution. However, the indiscriminate nature of acid leaching results in a solution, akin to a metal soup, containing not only the Cu and Co but also an extensive suite of other metals. These other metals, notably Fe, Mn, Al, Ca, Mg and Si, all have to be eliminated from solution before the copper and cobalt can be recovered. Generally precipitation processes are used, but these tend to result in significant losses of copper and/or more usually cobalt from solution, leading to reduced recoveries. The AmmLeach® process uses ammonia-based chemistry to selectively leach the target metals, leaving the rest behind in the leach residue. This approach eliminates any need to clean the solution of unwanted metals and the consequent metal losses. After solid–liquid separation, the leach solution is immediately subjected to separation and concentration of the copper and cobalt using solvent extraction and electrowinning. INTRODUCTION The Copper Belt extends through the northern part of Zambia and the southern province of Katanga in the Democratic Republic of Congo (DRC) and contains the richest and highest grade deposits of copper and cobalt remaining in the world. Whilst there are a number of mines that produce sulphide concentrates, using froth flotation, the largest deposits are those where near-surface sulphides have been weathered over time to form oxides. The oxides cannot be concentrated by conventional physical means to give high recoveries. Despite this, a number of dense medium separation plants have been installed and used to produce a higher grade concentrate which is typically exported (while the rejects, typically 2 to 3% Cu are stockpiled for treatment at a later date). These plants generally have low recoveries and can only be used on the dwindling supply of high grade materials. In exporting the concentrate, little value adding is undertaken within the country, thus greatly reducing the economic benefits to the country. Recent changes to the regulations in the DRC will effectively ban the export of low value ores, concentrates and intermediates in favour of high value metals. This will necessitate mines to install new processing circuits in order to comply with these regulations. The head grade of ores currently being treated in the DRC is slowly decreasing as the extremely high grade materials are being selectively mined out. In many cases, the removal of a small volume of high grade materials leaves a much larger volume of economically marginal ore behind. This is due to a desire for short-term profits overtaking long-term prosperity. The remaining ore, which in many cases is still of relatively high value by world class standards, is likely to be only treatable by low cost heap leaching. There are some initial trials of heap leaching within the DRC, but implementation at a large scale has yet to be adopted."

Jan 1, 2015

By Raymond O. Dannenberg

Potential processes for the recovery of precious metals and copper from diverse types of complex electronic scrap were investigated. Leaching-type processes were not successful, and attempts to physically separate the various gangue metals and plastics from more valuable components were also unsuccessful. The most promising approach was a smelting process, followed by electrolytic treatment to separate precious metal from copper. Recovery of precious metals from the anode sludge may follow conventional procedures. An alternative to the above process is incorporation of the scrap with the concentrate fed to an industrial copper reverberatory or converter furnace, possibly preceded by direct melting to form an assayable bullion and dross.

Jan 1, 1970

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016

By R. J. Miller

Mechanized Roof Supports (MRS) have dramatically improved safety and productivity of retreat pillar mining in coal. Due to low capital cost and greater flexibility, retreat panels have in some cases approached the productivity of a longwall. Because of improved safety and rapid set-up time when compared to conventional timbering, MRS are driving a return to retreat pillar mining in many situations. This paper describes how panel layout can be optimized for safety and operational efficiency when using MRS for retreat pillar mining of coal. The potential for significant unit cost reductions will also be addressed.

Jan 1, 1996

By F. Habashi

"While bioleaching of pyrite concentrates has been successfully used in industry to liberate gold from the sulphide matrix for subsequent cyanidation, the same technology cannot be recommended for leaching chalcopyrite concentrates for copper recovery. It will be shown to be uneconomical and cannot compete with pressure leaching technology. Data on the pilot plants that were constructed for this purpose and were shut down will be given.INTRODUCTIONBacterial leaching has been successfully applied for heap leaching of low-grade copper ores (Habashi, 1978, 1999). One of the major operations is that at Bingham in Utah (Figure 1). The leach solution collected at the bottom of the heap is extracted by organic solvents and the strip solution is electrolyzed to get high purity copper. The process was extended to treat auriferous pyrite concentrates to liberate gold and render it amenable to cyanidation by a process known as BIOX (Marsden & House, 2006; Lunt & Briggs, 2005).BIOX plants currently or recently in operation are the following:??Ashanti Goldfields Company, Ghana. Designed with an initial capacity of treating 720 tonnes of concentrate per day, the Sansu plant has since been expanded and currently has four modules processing 960 tonnes per day in all. It is by far the largest biooxidation plant in the world. The capital cost of the plant totalled US $25 million (1994 terms) and the operating cost is currently US $17/tonne milled.??Fairview, South Africa. The plant at the Fairview mine in Barberton, which was the initial pilot plant, has been fully operational since 1986. It was originally designed to treat 10 tonnes/day of concentrate but with the success of the project this has been increased to 55 tonnes per day. With the purchase of Fairview by Avgold’s Eastern Transvaal Consolidated, Avgold concluded a licensing agreement with Gold Fields, formerly known as Gencor, entitling it to use the BIOX technology to treat itsconcentrate.??Saõ Bento, Brazil. A BIOX plant was recently in operation in Brazil at the Saõ Bento Mine where a pressure oxidation circuit is used to treat the refractory flotation concentrate. This plant has confirmed the viability of combining bio-oxidation with pressure oxidation as a cost-effective method ofincreasing capacity at an existing oxidation plant.??Wiluna, Australia. The plant at Wiluna Gold Mine, Western Australia, was commissioned in 1993. Although originally designed to treat 115 tonnes per day of concentrate this has subsequently been increased to 158.??Other plants at Tamboraque in Peru, Harbour Lights and at Youanami in Australia have been commissioned recently."

Jan 1, 2012

By Adams F. C, Ridley K. L

Economic conditions after WorId War II made the recovery of Australian sources of sulphur one of considerable national importance. From 1947 to 1949 an investigation was made of recirculation techniques to produce acid plant grade gas from the Dwight-Lloyd down-draught sintering plant.During 1949 it appeared feasible to produce a gas of suitable 802 concentration and a decision was made to construct a gas purification train and a 150 tons/day contact acid plant. However, a number of difficulties remained in the production of the gases for sulphuric acid manufacture and as a result of research conducted to overcome these troubles the continuous up-draught sintering process was developed.The principal difficulties were:(a:) The down-draught sintering practice, as developed, produced an unusually high metallic lead precipitation in the windboxes. The disposal of this lead interrupted sintering operations and the delivery of gas to the acid plant.(b) The production capacity of the existing sintering plant was fully extended and the adoption of recirculation of gases, in an endeavour to satisfy acid plant requirements, would probably reduce the plant production capacity.(c) The prevailing high temperature of water available for purification train cooling required a higher than...

Jan 1, 1956

By R. Allan Wallis

In the past mining engineers have tended to rely heavily on the advice of fan manufacturers in relation to fan equipment issues. A more adequate approach was advocated in a paper [ Wallis, 1965 ] submitted to the Eighth Commonwealth Mining and Metallurgical Congress held at Surfers Paradise, Australia during 1965. At that time Mount Isa Mine were in the process of installing 3 large 6096mm (20ft) diameter vertical axial flow surface fans of an advanced type [ Mathews et al, 1967 ]. The preliminary feasibility studies prior to preparing the detailed job specification for this project were extremely thorough with the result that it was possible to include detailed information and instructions in the document, ensuring the procurement of equipment that was satisfactory in all respects. Full advantage was taken of expert services provided by external organizations during the large coordinated multi-disciplinary exercise. My continuing activity and development in relation to the technology of axial flow fans is now at a stage where all known design and performance data are accessible through CAD programs [ Wallis and Kipp, 1987 ]. The extensive calculations that were necessary in 1983 can now be carried out in a mere fraction of the time, and with complete confidence. Model testing in order to validate the fan and duct design proposals is, in my view, no longer essential. The first of the computer programs enables a mine ventilation engineer to study a large number of alternative axial fan arrangements for comparison with the centrifugal alternative. By entering the volume flow rate, fan pressure and air density, he can then with ease, and rapidly, investigate the effect of various blading arrangements, downstream evasee area ratios, and hub ratios, on fan diameter and speed, with their related attainable fan efficiencies. This procedure had its origin back in the 60s when I was advising mining companies on new fan equipment. At that time such an investigation was quite lengthy and lacked the precision and completeness that is now available within the present programs. To obtain the major benefit from these outputs, it is most important not to be disconcerted by the three very important nondimensional parameters, namely, the tip flow coefficient (LAMt), the fan pressure coefficient (Kt or Kit), and the swirl coefficient (Es and/or Ep) as these are important when assessing the various design proposals. When seeking an understanding of the role and importance of each of these variables, ample help is provided in the user manual; the design recommendations are summarized in the help screens which are readily accessible within the design programs.

Jan 1, 1989

By J. E. Elliott, K. O. Miller

Solubility studies were carried out to establish the phase distributions for various Fe-Ni-Pb-C alloys at temperatures where the metallic components exist as liquid solutions. Temperature us composition diagrams for the Ni-Pb, Fe-Pb, Fe-Ni-Pb, and Ni-Pb-C systems are derived by employing various approximations in conjunction with the data. Results are summarized for 1550°C in a quaternary phase diagram of the Fe-Ni-Pb-C system. BECAUSE surprisingly little information has been published on the phase diagrams of the Ni-Pb, Fe-Pb, Fe-Pb-Ni, and Fe-Ni-Pb-C systems, a study of these systems was undertaken to ascertain the important phase relationships in the temperature range of 1300" to 1550°C. Measurements were also made on the carbon-saturated systems in the hope that they would assist in the interpretation of the systems without carbon. This paper reports the results obtained from the simple equilibration of the various liquid and solid phases. EXPERIMENTAL PROCEDURE The experimental technique involved holding appropriati quantities of the metals in an alumina crucible, or in a graphite crucible when saturation of the melt with carbon was desired, for sufficient time at the desired temperature to ensure equilibrium. Then a sample of each liquid phase presen was drawn into a small-bore silica tube. This sample was withdrawn quickly from the furnace, cooled, and sent to the chemical laboratory for analysis. The cell assembly used is shown in Fig. 1. Durin the work on the Fe-Pb-Ni system, it was placed in a furnace wound with 20 pct Rh-80 pct Pt wire. This furnace eventually failed and subsequent studies were carried out between 1350" and 1475°C in a tube furnace heated by silicon-carbide resistance elements. A protective atmosphere of argon with approximately 10 pct hydrogen was supplied to the cell assembly at a gage pressure of 1 in. of water. Hydrogen was passed over palladized alumina and then anhydrous calcium chloride for purification. Argon was purified of oxygen and water vapor by passing it over copper gauze at 550°C and then through a calcium chloride drying column. The gases were mixed and redried before they entered the equilibration cell. Temperature was measured by calibrated Pt/Pt-10 pct Rh thermocouples and a Rubicon Type B potentiometer. The thermocouples were standardized against the melting points of pure nickel

Jan 1, 1961

By J. M. Czaplicki

The problems connected with deep mine hoisting and the increasing complexity of this process can be analysed through the application of such mathematical tools as stochastic modelling to study the effectiveness, reliability or safety of hoist methods. To relate these theoretical investigations to real practice, knowledge about components, their stochastic nature and stochastic order of appearance is necessary. This paper presents results obtained during the ten-year (1976-85) period of research undertaken in the Polish mining industry by the Mining Mechanisation Institute of the Silesian Technical University, Gliwice, Poland.

Jan 1, 1987

By Tzung-mow Yao, S Ki, J Word, J Vinson

Properly designed evapotranspirative (ET) cover systems can greatly reduce the amount of infiltration and groundwater recharge (deep percolation) into potential acid generating mine waste. In arid and semi-arid environments, infrequent precipitation, low measurable subsurface fluxes, spatial variability within mine waste and cover material, and evapotranspiration from below the cover system create challenges to monitoring moisture flux in these systems. Sloped ET single-layer (monolayer) cover depths and a variety of reclamation treatments are being studied at a copper tailing impoundment in Arizona, USA. To monitor the performance of different ET cover systems in response to precipitation patterns, four different test plots consisting of two different cover depths and two different vegetation densities were instrumented with heat dissipation sensor nests. The sensors measure the soil water pressure potential and allow hydraulic gradients to be determined within and below the cover systems to depths of 180 cm. Three replicate sensor nests were installed in each test plot to account for variability in materials and test plot treatments. Data collection occurs twice daily and is ongoing. Weather during the 26-month monitoring period was characterised by two months of greater than normal precipitation followed by nine months of normal precipitation and 15 months of abnormally dry conditions. Monitoring data indicate that deep percolation occurs in response to periods of extended precipitation, however, drying was observed to depths of six feet below the surface in all test plots. Using conservative assumptions regarding tailing hydraulic properties, one-dimensional downward flux predictions based on the monitoring data indicate very low (Additional long-term monitoring and installation of deeper and replicate monitoring sensors into tailings without cover systems are recommended to evaluate the long-term ET cover system performance and develop a better understanding of deep percolation rates at the sites.

Jan 1, 2003

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968

By D. N. Nilsen

A mathematical modeling method was developed by the Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of copper. The use of models for predicting the amount of metal extracted can reduce the amount of experimental work required to characterize a system for purposes such as optimization studies. Models were developed for the extraction of copper from ammoniacal sulfate and carbonate solutions with commercially available extract ants commonly used by industry. Results from laboratory shakeout tests compared well with predictions of the equilibrium concentrations of copper and pH values. For example, the loading of copper onto the solvent was predicted for most cases within ±S pct of the measured values, and the pH to with-in ±O.l pH unit in sulfate systems and ±O.2 pH unit in carbonate systems. Both mechanistic and empirical extraction equations were developed from laboratory data for copper and ammonia. The empirical-based models were slightly more accurate than were the mechanistic-based mod-els. Industrial level concentrations of the aqueous and organic constituents were used in this work. Independent variables included copper concentration, ionic strength, and initial pH of the aqueous phase; extractants, diluents, and their concentration in the organic phase; and temperature.

Jan 1, 1988

By C. Chu

A theoretical investigation has been made of the forward combustion process using a one-dimensional linear mathematical model, taking into consideration the effect of the vaporization-condensation which occurs on the leading edge of the heat wave. This work involves the solution of five coupled partial differential equations. Besides the vaporization-condensation phenomenon, these equations account for conduction, convection, combustion, heat loss, diffusion and bulk fluid flow. For the one-dimensional linear model studied, the vaporization-condensation phenomenon does not induce appreciable change in the temperature at the combustion front; and its primary effect is to create a steam plateau and to increase the length of the heated zone ahead of the combustion front. This effect becomes more pronounced at lower pressures, higher porosities or reduced gas saturations. The peak temperature and the temperature profile on the leading edge of the heat wave stabilize after a certain period. The length of the steam bank remains practically constant, although the length of the water bank increases as the heat wave advances. INTRODUCTION The existence of the vaporization-condensation phenomenon in the heat-wave process and the important role played by the phenomenon have been recognized by several investigators. Kuhn and Kochl stated that steam plateaus were frequently observed on the temperature records of their experiments. The steam plateaus were attributed primarily to the vaporization and subsequent condensation of the interstitial water existing in the oil sand. Szasz2 suggested that both lighter hydrocarbons and water are vaporized on the leading edge of the heat wave, carried forward in the gas stream, and then condensed to create banks of oil and water. Martin et al suggested that the vaporization-condensation phenomenon is one of the main mechanisms of the heat-wave process, along with thermal expansion and viscosity reduction. Wilson et al. reported the existence of a steam plateau several inches in length in their small-scale tube-run experiments. However, this important phenomenon has never been taken into consideration in the numerous theoretical analyses by various authors. 5 The purpose of this work was to study the thermal aspects of a linear heat wave, taking into consideration the vaporization-condensation on the leading edge of the wave, to determine the effect of this phenomenon on the temperature profile of the reservoir, and to investigate how this effect varies when other process variables are changed. THEORY We consider a reservoir of porous medium of cross-sectional area A, extending from x = 0 to x = L. This reservoir contains, aside from the solid matrix itself, a gas phase and a "combined liquid phase" which is a combination of two immiscible liquid phases — namely, an oil phase and a water phase. The oil present in the reservoir is assumed to consist of three fractions, a noncondensable gas, a nondistillable residuum, and a vaporizable oil fraction which may be present in both the gas phase and liquid phase. Before the heat-wave process begins, preheating has taken place and has imparted an initial temperature distribution T,(x) to the reservoir. At the start of the process, a stream of oxygen-bearing gas is introduced through the face at x = 0. This gas supports the combustion of the residual fuel and supplies the heat throughout the process. In order to develop a tractable system of equations, the model properties are postulated as follows: (1) the system is isotropic and homogeneous; (2) there is a uniform fuel content throughout the reservoir; (3) combustion takes place in a moving vertical planar region of infinitesimal thickness; (4) the temperatures of the fluids and the solid matrix are identical; (5) radiation is negligible; (6) the gas and liquid saturations are uniform throughout the reservoir and remain unchanged

Jan 1, 1965

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By D Reid

Many of the relevant engineering behaviours of tailings are controlled to a large degree by the density of the material. For example, loose tailings are prone to brittle strength loss, while dense tailings are dilative (i.e. gain strength) at large shear strains. The critical state framework has been successfully developed over the past few decades to assess whether in situ conditions are contractive or dilative, and estimate relevant engineering parameters on that basis. Tailings comprising primarily silt-sized particles, when subaqueously deposited, often form a particularly loose state compared to subaerially deposited material of similar index properties. Such subaqueous deposition occurs in the decant pond area, where the tailings typically pluviate in quiescent conditions within a pond of standing water. Silt tailings deposited in such a manner have been observed to be extremely loose in a number of TSF investigations. Of particular concern, the deposited material in such cases appear to be significantly looser than can be reproduced in the laboratory - even using moist tamping, the sample preparation method which can usually produce the loosest samples possible in laboratory conditions. While the loose density of subaqueously deposited silt tailings is clear, in a well-managed upstream-raised TSF the decant pond is usually small and far from the perimeter embankments, however there are a number of examples where the engineering performance of such materials becomes relevant – for example, when historical deposition practices were poor, resulting in subaqueous deposition near the perimeter embankment. This paper outlines the geotechnical characterisation of a number of such subaqueously-deposited zones, compares the in situ state to that achievable in the laboratory, and discusses options for assessing the expected engineering performance of such materials when comparable laboratory tests are unavailable.

Jul 1, 2021