Search Documents

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008

By Charles S. Barrett

NUMEROUS determinations1-7 of the tex-ture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Wever1 and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the roll-ing direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist.

Jan 1, 1940

ONE of the phases of mining wide ore-bodies, such as are found in Broken Hill, is the laying-out and design of the sill floor gangway timber, When, in the above operation, a detail has to be repeated frequently, it is desirable in the interests of efficiency that that detail should be standardized as far as possible. Before arriving at a standard design e.g., a crosscut layout-it would seem necessary to compare its strength with some other unit of timber and see that the general design is at least as strong as the unit that has been taken for comparative purposes, In these notes no attempt is made to calculate the stresses to which timber underground is subjected, but merely to draw a comparison between the relative strengths of the various cross sections of timber in common use underground.It has been assumed for the purposes of comparison that the milling exerts pressure in a vertical plane only, and is uniformly distributed over any area. A beam supported at both ends, and with a uniformly distributed load, has the maximum bending moment at a point midway between the points of support, and equals- WL2 8 where W = load per unit length. L = distance between points of support.The bending moment also equals M-, where y M = modulus of rupture of the material in question. I = moment of inertia of the section of the beam about a given axis.Y = distance of extreme fibre from that axis. WL2. I The formula -8- = MY- only holds good until the elastic limit...

Jan 1, 1923

By S. J. Aresco, George E. Keller, J. Visman

INTRODUCTION The accurate sampling of coal, as with most minerals, is a difficult task. Coal is a very heterogeneous material made up of different types of coal and varying amounts of mineral matter. The product as mined may contain all of the layers of coal and impurities found in the seam as well as portions of the strata above and below the coal seam. The preparation plant is the device to size, crush and/or remove impurities so that the coal may be shipped as a saleable product. Sampling may be needed at many stages in the preparation process. Although this chapter is mainly concerned with sampling in connection with preparation processes, the principles will apply to all coal sampling. The main reasons for sampling in connection with coal preparation are: 1. To determine the washability characteristics of the raw coal by means of float and sink tests. These may be used for the design of a preparation plant, prediction of results to be obtained or for monitoring raw coal delivered to the plant. 2. To check the performance of various operating units in the plant, either by float and sink tests or chemical analyses. 3. To determine the analytical characteristics of the products produced, such as moisture, ash, Btu, sulfur, etc. HISTORY The earliest accepted methods of sampling coal in the United States were given in U. S. Bureau of Mines publications by J. A. Holmes,1 G. S. Pope2 and A. C. Fieldner.3 The American Society for Testing and Materials more or less adopted the methods proposed by the U.S. Bureau of Mines in their Standard D-21-1916, and it remained a standard for many years. Briefly, the standard called for a 500 pound sample for coals less than. 3/4 -in. in size and a 1,000 pound sample for all coals over ?4 -in. in size. No mention was made of increments but there was an instruction that the sample should spread over the coal to be sampled. Sample preparation was by hand crushing with the alternate shovel method for reduction to 250 pounds followed by coning and quartering below 250 pounds. Obviously, with the amount of work involved, this method of sample preparation was rarely followed. This method of preparation resulted in samples that were practically air dried because of long exposure while crushing, shoveling and quartering. In the late nineteen twenties and early nineteen thirties, studies for more practical methods were begun. Dr. E. S. Grummell4, Imperial Chemical Industries, Ltd, London, summarized the work to date at the

Jan 1, 1968

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44 to 65% depending on bench height. This model was then applied to field tests at an eastern, contour, coal stripping operation. Results from five experimental casting shots are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35 to 65% with an average of 50%. Fragmentation was improved and it was demonstrated that this procedure is economically attractive with a resultant cost savings of $.59/m3 or $5.93/t of clean coal.

Jan 1, 1987

By J. A. Bailey, J. H. Tundermann

The dihedral angles of the solid-liquid interfaces were measured at various temperatures above the solidus and the interfacial energies calculated when small additions of copper, indium, lithium, magnesium, antimony, and silicon were made to an aluminum alloy containing 3 pct Sn. When the results were compared with those of the Al-Sn alloy some differences were found which could be interpreted in terms of the ability of the added element to enter into solution or form intermetallic compounds with the aluminum and tin. It was shown that in some cases considerable changes in the shape of intergvanular liquid films can be brought about by comparatively small compositional changes in the alloy. DURING the melting or solidification of an alloy a temperature range is usually found where the presence of a liquid phase may be detected at the grain boundaries of a solid. It is believed that the presence of this liquid phase is responsible for hot tearing in castings and welds and hot shortness in the working of some alloys at elevated temperatures. Rosenberg, Flemings, and Taylor1 in a study of the solidification of aluminum castings have indicated the importance of intergranular liquid films and shown that their shape and distribution at the end of solidification effect the hot tearing characteristics of the material. The shape of such intergranular liquid films are determined largely by the ratio between the solid-liquid interfacial energy (yLS) and the grain boundary energy (ySS). A measure of this ratio (yLS/ySS , relative interfacial energy) is the dihedral angle 8. The dihedral angle 0 is related to the relative interfacial energy by the following expression: Rogerson and Borland 2 have also suggested that the shape of the intergranular liquid is an important factor in determining the susceptibility of a material to hot shortness. They showed that on a comparative basis materials having the lowest dihedral angles at a given temperature gave the greatest severity of cracking. They stated that liquid in the form of globules should be less harmful than liquid in the form of extensive films as more intergranular cohesion should be possible. Rogerson and Borlland 2 also showed that the susceptibility of an A1-Sn alloy to hot cracking can be reduced by small additions of cad- mium. It was found that the cadmium gave an increase in the dihedral angle at all temperatures. Ikeuye and smith3 investigated changes in the dihedral angle and relative interfacial energy with temperature for a number of ternary alloys formed when small additions of bismuth, cadmium, copper, lead, and zinc were made to an A1-Sn alloy. They found that in most instances changes in the dihedral angle were caused by compositional changes in the liquid phase; as the composition of the liquid approached that of the solid the dihedral angle decreased. They noted that the addition of a third element which was soluble in both the liquid and solid phases at a given temperature may decrease the dihedral angle (e.g., the addition of copper or zinc) but otherwise the ternary alloys formed exhibited dihedral angles between those of the A1-Sn binary alloy and those of the binary alloy of aluminum with the added element. Dwarakadasa and Krishnan4 investigated the changes in dihedral angle and relative interfacial energy with temperature when small additions of magnesium, iron, silicon, manganese, sulfur, cobalt, and silver were made to a copper alloy containing 3 pct Bi. They found that in all cases the added elements gave an increase in the dihedral angle and relative interfacial energy when compared with the values obtained for the simple binary alloy at the same temperature. It was noted that an increase in temperature gave a decrease in dihedral angle and relative interfacial energy in each of the ternary alloys studied. Similar results have been obtained by Ramachandran and Krishnan5 for the addition of small quantities of lead. This paper describes the application of dihedral angle measurement to the determination of the shapes of liquid phases at various temperatures above the solidus when small additions of copper, indium, magnesium, lithium, antimony, and silicon are made to an aluminum alloy containing nominally 3 pct Sn. An attempt is made to correlate the measurements with the relative solubility of the added elements in tin and aluminum. The work was undertaken to provide more data concerning the effects of temperature and composition on the shape of liquid films above the solidus. EXPERIMENTAL PROCEDURE In the present work ternary aluminum alloys containing nominally 3 pct Sn and small additions of high-purity copper, indium, lithium, magnesium, antimony, and silicon were made. The alloys were melted in a graphite crucible under an inert atmosphere of argon and cast into ingots 6 in. long by 0.5 in. diam. The ingots were then cut into rods 1.5 in. long, given a 50 pct cold reduction, and machined into test pieces 0.5 in. long by 0.5 in, diam for heat treatment. The alloy samples were annealed at the various test temperatures between the liquidus and solidus for approxi-

Jan 1, 1967

By M I. Pownceby, N A. S Webster, R Pattel, N Ware

The decrease in quality of Australian iron ore, coupled with the demand for more efficient energy use, necessitates closer monitoring and optimisation of process conditions for iron ore sinter production. Sinter properties are correlated with the mineralogical content and traditionally, quality control has relied on methods such as Fe2+ determination, point counting via optical microscopy and automated electron beam techniques such as QEMSCAN; these can have a typical turnaround time of several days between sampling and reporting of results. As well, there is additional uncertainty around quantifying some of the complex mineralogical phases in sinter such as silico-ferrite of calcium and aluminium (SFCA) and SFCA-I, which are key phases influencing sinter quality. There is a clear need for the implementation of alternative analytical methodologies that offer a turnaround in hours or even minutes to provide information to accurately maintain production conditions.X-ray diffraction (XRD) is a technique widely used for the quantitative mineralogical phase analysis (QPA) of ores and processed materials in the iron ore industry. Partial least squares regression (PLSR) analysis methods have recently been suggested as an indicator of sinter Fe2+ content from powder XRD data without the need for rigorous and often time-consuming mineralogical analysis by the operator. In this study we provide results from the implementation of PLSR to predict the strength of iron ore sinter. Results are sourced from a well-constrained data set comprising strength properties (as quantified by a tumble index (TI)) from a series of compact laboratory test samples. Using this data set it was determined that PLSR has potential to be used as a method for calculation of sinter TI from powder XRD data and, therefore, process control.CITATION:Webster, N A S, Pownceby, M I, Ware, N and Pattel, R, 2017. Predicting iron ore sinter strength through X-ray diffraction analysis, in Proceedings Iron Ore 2017, pp 331–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By William B. Plank

THERE are 19 pct fewer undergraduate and graduate mineral engineering students enrolled in the ECPD accredited schools of the United States this year than there were a year ago. The figures are: 8727 this year and 10,674 last year. The entire engineering group in both countries numbers 171,070, as compared with 184,547 last year and 252,250 in 1947-48, the peak year. This is a decrease of 7.3 pct since last year, less than half as much as the decrease in the mineral engineering group. These figures on engineering enrollment for the current year, 195.1-52, in colleges of the United States and Canada were prepared jointly by the U. S. Office of Education and the American Society for Engineering Education. The seriousness of the situation is shown. by the reported demand for 60,000 to 90,000 engineers this year for civilian and defense industries and only 35,800 will graduate next June. Many of the 1952 graduates are subject to Selective Service, having been granted deferments while in college, and ac- [ ]

Jan 1, 1952

By Isabel F. Barton, Eytan Bos Orent, Mark D. Barton

A new examination of tabular uranium (U)-vanadium (V) deposits within the La Sal district places mineralization in the context of the complex fluid flow history that has occurred in the Paradox Basin and Colorado Plateau. As the only currently producing district of this deposit type in the region, the La Sal district provides excellent opportunities to study deposit- and district-scale features that can serve as exploration guides where exposure is limited. The absence of major structures along a narrow and elongate mineral trend that runs E-W across the southern part of the Utah-Colorado border indicates a regional lithologic control. The trend was likely influenced by Jurassic drainage patterns, as indicated by paleocurrent directions shown in Fig. 1. Fluvial sandstone host rocks in the Jurassic Morrison Formation contain significant evidence of multiple superimposed fluid systems that have progressively changed local mineralogy. Apart from the presence of ore minerals, remnants of fluid systems are preserved as cements including quartz overgrowths, compositionally distinct carbonates, and sheet silicates. New geochronology methods provide constraints on the timing of initial mineralization and later remobilization. U-Pb ages of calcite associated with ore minerals provide evidence for Early Cretaceous mineralization, whereas textures and K-Ar ages show that early-formed V-minerals were replaced at the expense of V-bearing micas and clays during the Eocene. The paragenesis of minerals in U(-V) deposits of the La Sal district reflects the complexity of a sedimentary

Feb 1, 2025

By J. M. Candia

El presente artículo describe las rampas o túneles inclinados utilizados en el nuevo sistema de minería que permiten la circulación de vehículos y equipos pesados que se mueve sobre llantas de jebe con el objetivo de reducir los costos de explotación, manipuleo y extracción del mineral de baja ley que en otro sistema no podría trabajarse económicamente.

Jan 1, 1971

By X. B. Starnes

"INTRODUCTION The Eva Tanguay property is in Crittenden County, Kentucky, about 1 mile south or the village of Mexico, and can be reached from Marion, the County seat, by travellng south on State Highway 91 for 6.8 miles and then turning southwest on State Highway 70 and traveling 2 miles farther.Although the property lies between the Huffaw and Pigmy properties, which together have produced 200,000 tons of fluorspar ore, production from the Eva Tanguay has been estimed at only 1,000 tons. Geological factors on the property indicated the likelihood of an ore occurrence, and the author examined the property in April 1944. Shortly thereafter, the U.S. Geological Survey wrote a report on the property, which was not published. A drilling program was initiated by the Bureau of Mines November 1, 1944, and continued until eight holes totaling 3,137.5 feet were drilled.The holes showed that the Tubb fault system on the Eva Tanguay property is composed of three members, all of which contained commercial ore. The line dividing the Haffaw and Tanguay properties crosses the vein outcrops, causing a part of the ore indicated to be on each property.The mineral rights, which are leased by Robert Frazer of Marion, are owned by Mrs. O. S. Denny and W. C. Bohn, both of Marion."

May 1, 1947

By R. H. Sprute

The Federal Bureau of Mines performed laboratory tests using direct current to dewater and densify fine-grained coal sludge in order to alleviate disposal problems and lead to recovery of high energy value often present in this waste. The laboratory tests described in the main body of the report were performed on thickened underflow (no flucculant added) from a northern Appalachian coal preparation plant. Solids in this slurry was very fine with 65 percent of the particles less than 0.1 mm in diameter. A variety of application procedures tested is exemplified by a test in which a soupy slurry (55 percent dry-weight moisture content) was converted into a firm dense material with a 20-percent dry-weight moisture content. These results were achieved in 3 hours with current density of 3.7 amp/ft2 and a power expenditure of 35 kwhr/yd3. The treated material has an average heating value of 10,400 Btu/lb. Varying current density, electrode configuration, and placement depth makes application of the treatment flexible. Two other types of sludge were tested briefly--thickener underflow from a southern Appalachian coal preparation plant with flocculant added, and sludge from an acid mine drainage treatment plant. The underflow responded well to the treatment, but response of the sludge from the acid mine drainage treatment plant was poor.

Jan 1, 1976

By C Ausa, Nyunt Htay, A, L Deiparine

The main tectonic elements in Myanmar are a late Mesozoic and Cenozoic magmatic arc system in the west, repeated in northern Myanmar by more than 300 km of dextral movement on the Sagaing Fault, and the back-arc continental region affected by early and late Mesozoic orogenies, in the east. Historically most lode gold production has been from latest Cretaceous high-grade mesothermal veins and derived placers in the Wuntho and Tagaung-Myitkyina segments of the magmatic arc. Placer deposits in the Ayerwaddy River north of Myitkyina are currently worked by more than 100-bucket dredges. South of Wuntho, the magmatic arc and Pegu Yoma fold belt host epithermal gold with associated As, Sb and Zn in mid-Tertiary marine sediments. MyanmarÆs most productive lode gold deposit, the Kyaukpahto mine, lies within a north-trending district east of the magmatic arc and north of Mandalay. Here mineralisation and associated jasperoidal silica occur in Eocene sandstones and Permian and Triassic carbonates. Possibly this district continues southeastwards, across the Sagaing Fault, as sediment-hosted Sb Au and locally skarn Au mineralisation within a 1100 km long fold-thrust belt. Also present in the back-arc region are sandstone-hosted Au Cu in a Palaeozoic slate belt, and gold and stratabound gold-base metal mineralisation in the medial metamorphic belt. While untested targets remain in the magmatic arc, particularly for high sulphidation Au, the best potential is clearly within the back-arc slate and fold-thrust belts in the western part of the Shan Plateau and in northeastern-most Myanmar.

Jan 1, 1999

Myths and misconceptions regarding cyanide in the mining industry are common. This is not surprising, given the other uses to which cyanide is, and has been put. Unfortunately, the economic benefits, largely due to the introduction of cyanide in towns such as Waihi are often unrecognized. In the current "green" environment, the New Zealand mining industry faces constant scrutiny and challenge. The use of cyanide in hard rock mining is one area which can stir the emotions of the public.   Cyanide can be transported, stored, used and disposed of in a safe manner. The modem mining industry has an excellent record regarding the safety and environmental issues relating to cyanide. Many of the fears relating to cyanide in the mining industry have proven to be unfounded. It is important that this reputation is maintained. This is possible given proactive and ongoing management of cyanide issues.

Jan 1, 1997

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By R. M. Owens, J. F. Lupo

The Shirley Basin Uranium mine, located in southeastern Wyoming, USA, was an open pit mining operation consisting of a series of several open pit mines excavated into poorly consolidated sandstones, siltstones, and claystones. Since the initial open pits were developed in 1969, slope failures have plagued the mine and mining operations. These slope failures have persisted into the current mine reclamation period. When the mine was first developed, the open pit slopes were designed to range between 45 to 55 degrees. Numerous slope failures during mine development required the pit slopes to be redesigned with slopes as shallow as 26 degrees. At present, movements are occurring within the open pits on reclaimed slopes that are shallow as 12 degrees. Several detailed slope studies were conducted at the mine in the early 1970s. These studies, combined with more recent geotechnical investigations, provide a unique detailed history of pit slope failures on shallow slopes. This paper presents an evaluation of the slope failures at the Shirley Basin mine, highlighting important mechanisms causing slope failures on very shallow slopes. The evaluation demonstrates important key parameters for shallow slope design.

Jan 1, 2001

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990

By E. R. Borcherdt

METHODS and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. EXPLORATION Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. STOPING For many years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1941

By C. C. Blade

"This report on the properties of motor fuels sold through service stations ni the Unietd States is a continuation of a series of reports made in accordance with a cooperating agreement between the Coordinating Fuel Research (CRF) Committee of the Coordinating Research Council (CRC)3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.4/ Further reports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941.4/ No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.4/The present report presents analytical data for 1,381 samples, representing the products of approximately 75 companies. Most of the samples represented in this report were secured during July and the first half of August, 1945. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples – regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items and brands comprising each group is as follows: Regular-price, 733 samples, 229 items, and 57 brands; premium-price, 504 samples, 197 items, and 56 brands; third-grade, 84 samples, 28 items and 12 brands. The meanings of these terms as sued in the surveys are as follows:"

Jan 1, 1946