Search Documents

By S. J. Mitchell

An analysis of bolting reinforcement of several large [approximately 18 m (60 ft) cube] pillars was performed. The many overcoring stress profiles in pillars at the mine were used to produce generalized stress distributions at various stages in pre- and post-failure. A complete stress-deformation curve was estimated from this data. The effect of pillar bolting on the load-deformation behavior was extrapolated from the observed unbolted behavior. Bolting can increase pillar strength by up to 10 percent. The effect of bolting on general mine stability was examined with a shoW computer analysis. The computer model was calibrated against measurements performed at the mine, and produced good agreement between measured and modeled stresses. The analysis indicated that bolting increases the bolted pillar safety factors in the event of additional pillar failure by a small amount (approximately 5 percent). Progressive pillar failure is unlikely, because arching transfers most load from yielding pillars to large unmined abutments rather than to the smaller panel pillars.

Jan 1, 1984

Later this month (June 24-27) in San Francisco, the Society of Mining Engineers of AIME, together with the American Society of Civil Engineers, the Canadian Institute of Mining & Metallurgy and the Engineering Institute of Canada, is sponsoring the second biannual Rapid Excavation and Tunneling Conference. The dominant theme of the Conference is the practical application of techniques and research relating to underground rapid excavation and tunneling. In the following pages, ME gives highlights of many of the 24 technical sessions and some of the papers being presented. The full proceedings of the Conference will be published by SME-AIME later this year.

Jan 6, 1974

By W. F. Cannon

Many high-grade manganese deposits of the world occur in marine transgressive sedimentary sequences deposited on stable platforms. These include the Nikopol and related deposits in the Soviet Union and Groote Eylandt, Australia, among others. We suggest that the Atlantic and Gulf Coastal Plains and the vast area of Cretaceous rocks in the middle of North America are favorable provinces for sedimentary manganese deposits because regionally transgressive units are widespread. North America has 16% of the world's land area but only about 0.2% of known high-grade manganese reserves. This disparity is difficult to reconcile in view of the fact that large areas of North America are underlain by rocks that we consider at least broadly favorable to contain manganese ores, and we suggest, therefore, that important high-grade deposits remain to be found in North America.

Jan 1, 1982

By David R. Morrey

During the past 50 years, significant research has been performed in the ecology and physiology of plants that colonize soils containing elevated concentrations of heavy metals. Similar work has also been performed on plants that are able to survive acidic and saline environments. Efforts have focused on the ecological analysis of plant communities that occur over a range of metalliferous mining wastes. Investigations have been performed on the mechanisms that allow selected varieties of plant species to survive in normally phytotoxic environments and on the potential applications of metal-tolerant varieties of plant species. The purpose is the remediation and reclamation of mining wastes and soils that contain unusually high concentrations of so-called heavy metals. Characteristics of some mineral wastes Metalliferous mining wastes present special environmental restoration problems because of their toxicity. Potential toxicities are mostly caused by residual metals derived from weathering of low-grade ore or the waste products of mineral processing. In cases where pyrite forms a part of the mining waste, acid generation by oxidation may exacerbate the toxicity problem by promoting heavy-metal mobilization in aqueous solution.

Jan 1, 1995

By Hal McVey

"Philosophy" addresses the definition and assigning of importance to the marketing of by-products. Two examples, one in metals and the other in industrial minerals, explore prime product to by-product relationships. Relative revenues from all products illustrate the importance of by-products to economic feasibility. "Mechanics" takes a broad view of the types of marketing organizations that are applicable to individual circumstances in the marketplace. In-house marketing as well as agents, merchants and trading companies are outlined and discussed. Philosophy Definition Of Terms Philosophy Definition Of Terms The definition of terns for a paper such as this is generally a necessary but not-very-interesting exercise. However, in simply trying to clearly define the term "by-product" some interesting relationships between products arise and the line of demarcation between "product" and "by-product" often becomes obscure. The search for that distinction represents the philosophy portion of the title. A couple of definitions of philosophy can even help to set the tone for what follows. According to Webster, philosophy is : 1 Pursuit of wisdom. 2. A search for a general understanding of values and reality.

Jan 1, 1983

By M. Kamali

In this research, in order to predict the peak particle velocity (PPV)(as vibration indicator) caused by blasting projects in the excavations of the Karoun III power plant and dam, three techniques including statistical, empirical, and neural network were used and their results were interpreted and compared. First, multivariate regression analysis (MVRA) was used as statistical approach. Next, PPV was predicted using some widely used empirical models. Lastly, an artificial neural network was used. In the ANN model, maximum charge per delay, total charge per round, distance from blast site, direction of firing, blasthole length, number of blastholes, total delay in milliseconds, number of delay intervals, and average specific charge were taken into consideration as input parameters and consequently the PPV as output parameter. The results of the techniques were interpreted from two points of view. Firstly, the correlation between the observed data and predicted ones, secondly the total error between observed data and predicted ones. The MVRA had a satisfactory correlation but its error of estimation was comparatively very high. The empirical model had reliable correlation and a small error of estimation; in total the results of empirical method were more reliable than those of MVRA. Generally, the ANN approach showed very high correlation and a very small error. The results of this research indicated that the ANN model is the best predicting model for PPV in comparison with other approaches.

Jan 1, 2010

By Jan D. Miller

The application of computers to the control and study of mineral processing operations such as grinding, classification and flotation has created an interest in simulation studies of these operations with mathematical models. Evidence of this interest is confirmed by papers presented at the 1969 International Computer Application Symposium held concurrently with the Fall Meeting of the Society of Mining Engineers in Salt Lake City, September 17-19, 1969. Proceedings of this symposium, entitled A Decade of Digital Computing in the Mineral Industry. were edited by Alfred Weiss and published by SME. Two sections of this book are devoted to computer application and simulation of mineral processing operations. In the area of comminution, several papers were presented at the International Computer Symposium. The size-discretized batch grinding model was described, and its application to the simulation of batch grinding, locked-cycle grinding and closed circuit grinding were discussed1. Freeh, Horst and Kellner2 approached simulation using a steepest ascent parameter-fitting technique, while Schoner3 considered the dependence of the elements of the mill matrix and classifier matrix on operating conditions, especially the feed rate.

Jan 1, 1970

By Georgy Cherkashov, Svetlana Babaeva, Tamara Stepanova, Firstova. Anna

Seafloor massive sulfides (SMS) study in the Russian Exploration Area at the northern equatorial Mid Atlantic Ridge began after signing the contract with International Seabed Authority in 2012. In order to evaluate the SMS resources in the course of exploration the major and rare metals with economic value should be determined. The evaluation is based on geochemistry and mineralogy and particularly on the type of rare metals occurrence in the SMS. As a case study research of the Semyenov cluster of SMS deposits have been conducted.

Sep 1, 2014

By N. Mungan

Laboratory water floods were performed in oil-wet and waterwet alundum and Torpedo cores, displacing a refined oil with n-hexylamine or Triton X-100 solution. Also, some floods were performed in which a sucrose solution was displaced with n-butyl alcohol. The Purpose ot the tests was to see if the oil recotlery could be increased and to examine what role the inter-facial tension reduction and wettability change play in the recovery mechanism. it was found that the chromatographic transport of amine was influenced by core wettability. In oil-wet cores, the rate of advance of the amine band could be predicted from equilibrium chromato-graphy, while in water-wet cores the amine band moved faster than predicted, indicating a non-equilibrium process. By reducing the interfacial tension to 1.1 dyne/ cm, oil recovery was increased. More oil was recovered from Dri-filmed cores than from water-wet cores. Reversing the wettability of the porous media from oil-wet condition also resulted in some additional oil recovery. Neutral wettability floods did not increase oil recovery. INTRODUCTION Interfacial forces in petroleum reservoirs are responsible for retention of large quantities of residual oil. Increasing exploration costs have created an incentive to attempt recovery of this residual oil by new and novel processes. One novel process involves changing the interfacial forces by introducing a chemical into the reservoir during water flooding. Recently, several investigators have carried out laboratory displacement tests using amines. lt3.4 The amines adsorbed onto initially water-wet core surfaces, changing them to oil wet. Additional oil was recovered when the cores were flooded in a manner reversing the. wettability from oil-wet conditions. In all these studies, the wettability reversal was considered responsible for increased oil recoveries although it was noted that amines also reduced oil-water interfacial tension. In the present study, displacement experiments were performed in water-wet and Dri-filmed cores. The purpose was to separate the effects of lowering the interfacial tension from changing the wettability. LABORATORY STUDY All experimental data given in this paper have been obtained at a temperature of 70F + 1 and prevailing atmospheric pressure. FLUIDS AND MATERIALS The oil used in these experiments* was washed with H2S04 and passed through two 100-200 mesh silica-gel beds to remove unsaturates and surface active impurities. Normal hexylamine** of practical purity was used, and the alundum cores*** were composed of nearly pure A1203. Fused quartz (SiOi) and Lucalox (A12 )t plates were used in the contact angle measurements. DISPLACEMENT TESTS Displacement tests were performed in alundum and Torpedo cores. Before displacement runs, cores were acidized with 0.1 normal HCI, flushed with distilled water and fired at 1,200F to make them water wet. This procedure also reduced water sensitivity of the Torpedo cores. Oil-wet cores were prepared from water-wet cores by flowing several pore volumes of 1 per cent by weight Dri-film SC-87 solution in heptane through the cores, flushing the cores with nitrogen, evacuating, and finally heating the cores at 300F for 4 or 5 hours. Between floods, cores were cleaned by conventional procedures and treated again as above.

Jan 1, 1965

By Jasper Stuckey

THE object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which-the Hot Springs and Kings Mountain -contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3 1/2 miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite-usually there have been less than three producers-and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage. was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926.

Jan 1, 1933

By L. H. de Wald, J. Walter Scott

It is usual practice in the copper industry to use open horizontal molds for casting tough-pitch copper wire bars.' A wire bar cast in this manner is partly characterized by heavy wrinkles and a comparatively deep skin of oxide on the top of the bar, corresponding to the open side of the mold. On the theory that the rough, high-oxide surface might have an adverse effect on the rolling and drawing properties of a wire bar and might account for some of the irregularities of mill behavior, several bars which had been planed to remove the wrinkled surface were processed into wire. These bars responded to mill treatment more satisfactorily than did the regular wire bars. Realizing that machining the surface of one face of each bar would not be commercially feasible, it was decided that casting the metal into a vertical mold and cropping off the pouring end would accomplish approximately the same result. Several wire bars of commercial size (250 Ib.) were so cast and processed into wire for comparative test with bars cast in the usual horizontal molds. It is the purpose of this paper to present the results obtained from this investigation, in which commercial bar sizes and processing technique were used throughout. The results show that in general copper wire bars cast vertically are superior to those cast horizontally. Experimental Procedure A horizontally cast bar and a vertically cast bar were obtained from each of several regular reverberatory furnace heats of copper which had been refined and poled to tough-pitch metal in accordance with usual methods.' Both bars were cast from the same part of the melt and within five minutes of each other, in order to produce as nearly as possible, in each case, wire bars of identical composition.

Jan 1, 1930

By S. G. Hardcastle, K. C. Butler, M. G. Grenier

The most common method of determining airflow employed by mine ventilation engineers is the product of i) the average air velocity as measured by a vane anemometer and stopwatch through a continuous traversing technique, with ii) the cross-sectional area of the roadway. This method requires the vane anemometer to accumulate the total flow over the duration of the traverse. Historically, this has been facilitated by a mechanical analog instrument that has either a counter or set of dials that display the flow. Common instruments of this type are Airflow Development's AM5000, Davis's, or Taylor's Biram type anemometer. The AM5000 is widely used in the Canadian mining industry but is no longer available. Therefore, regulatory authorities have seen fit to evaluate presently available commercial instruments to replace the AM5000. This paper describes an instrument evaluation contracted by the Atomic Energy Control Board of Canada which regulates the uranium industry. Over the last two decades there have been numerous advances in the development of electronic air velocity meters. Currently available units have the following features: a) battery operation; b) are compact and can be hand-held; c) employ LCD's, and microelectronic circuitry; and d) provide a time integration for the duration of a traverse. These features make such instruments a possible replacement to the analog units and stopwatch determinations. This paper details five of the new generation of vane anemometers plus a vortex air meter, and it explores their limitations in comparison to analog units. Specific consideration is given to linear response, the effects of yaw, traversing speeds and ergonomics relating to both handling and use. The paper concludes with some features that are attractive and should be considered when purchasing a new anemometer.

Jan 1, 1991

This paper reviews the current techniques employed in the prediction of subsidence and how they have been applied to partial extraction systems. The method using influence functions to describe the shape of the profile is investigated in detail and has been adopted to model the subsidence over workings in Huntly. It is compared with the profile methods developed in the United Kingdom and found to predict the subsidence profile more accurately than these methods.

Jan 1, 1991

By Juan Kobashicawa, Bernardo Falcón

En este trabajo se explican los controles automáticos desarrollados (In-House) e implementados en el circuito de Molienda de Compañía Minera Antamina, el cual abarca Molinos SAG, de Bolas y los Hidrociclones respectivos. Los controles implementados son basados en el Control por Lógica Fuzzy y las Bandas de Bollinger; así mismo se indican los criterios en el diseño de los controladores y las variables del proceso que se han tomado para la implementación donde se controla un indicador de distancia del centro de masa de la carga respecto al centro del molino de Bolas. Asimismo, se muestra el impacto positivo logrado con la estabilización del circuito.

Sep 1, 2017

By F. W. Maclennan

ORE production from the property of the Miami Copper Co. began early in 1911. Until 1925 this ore came from the so-called high-grade orebodies, which contained a little over 2 per cent. copper. This ore was mined by the following methods. 1. Top slicing after mining the peaks by square setting, which produced 4,524,347 tons, including ore from square setting. 2. Shrinkage stoping with sublevel caving of the pillars, which produced 2,230,577 tons. 3. Undercut caving with hand tramming, which, produced 15,427,672 tons. Estimating December tonnage, the total ore mined to the end of 1929 will amount to slightly more than 43,000,000 tons. The first method was described by E. G. Deane1 and the second by D. B. Scott,1 and the third, together with a general, description of the mine, by J. H. Hensley, Jr.1 The geology of the district has been worked out by. Dr. F. L. Ransome.2

Jan 1, 1930

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By S A. Myers, T Klein

The Yanacocha mining district is located in the northern Andes of Peru. The project is within the Cajamarca province, 20 km north of the town of Cajamarca and 600 km north of Lima, the capital of Peru (Figure 1). The district encompasses an area of 120 km 2 and is centred on the 78030'west longitude and 7000' south latitude. The project lies at an elevation of 3400 to 4200 masl.

Jan 1, 1999

"In the mines producing over 500 tons per day, skips have replaced the old method of hoisting ore by cars run onto cages. In the car and cage method, two men (station tenders) trammed the loaded cars onto the one-deck cage, and as the production increased the one-deck cage was increased to two decks and later to four decks. Landing chairs at the underground stations were necessary in this method and were the cause of many serious accidents by being carelessly left in the shaft by the station-tenders when leaving one station for anotherabove. The labor and time occupied in loading the leaving cages were con¬siderable, and, at times of rapid hoisting, four men were necessary in taking off empty and caging loaded cars. This also required at the surface landing, as many as ten men on a shift to remove the loaded cars and replacing them with empties, and tram the loaded ones to the surface ore bins, where the railway cars were loaded.The skips used in Butte are generally of 100 cubic feet capacity and hold five tons of ore, and weigh 7,500 lbs. The cage above, to which the skip is attached, weighs 2,300 lbs. The skips dump automatically into a pocket of 50 tons capacity. Two men are with the skips underground and load them from 125 ton capacity ore-pockets, under each station, the bottoms of the pockets having an inclination of 50 degrees from the horizontal. At the bottom of these pockets a gate is operated by compressed air. The labor of loading the skips amounts only to the opening and closing of a valve in the air-line, the ore running by gravity into the skips.Besides the saving in labor, the use of the skips has removed the necessity of underground landing chairs in the shaft and the accidents which are inevitable where such chairs are used."

Jan 1, 1913

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

By Alisson Paulo de Oliveira, Altair Lucio de Souza, Jacson Morais Borges, Cleiton Arlindo Martins

A customized version of the Microsim-PM software for one Steckel rolling mill was built and adapted for specific mill parameters. The focus of this study is to use this model, which predicts the austenite grain size distribution evolution during rolling, to understand and quantify metallurgical issues happening during hot rolling. This will allow the steel mill to optimize the rolling process and chemical composition before the first industrial trial. Materials rolled for final thicknesses of 4.75, 6.30 and 12.5 mm of a carbon manganese steel and a microalloyed steel were selected to tailor the equations used by the model and to accurately reproduce the reality of the Steckel mill. This paper analyses the results from the customized model and compares them to mill data and final microstructure. Measured and predicted Mean Flow Stress (MFS) values are compared. After rolling, the material is subjected to accelerated cooling using laminar cooling. These cooling curves obtained from mill data are also considered to analyze the final microstructure characterized for all the cases using EBSD. The quantification of the microstructure allows for a better understanding of the relationship between chemical composition, process parameters and mechanical properties.

Oct 1, 2019