Search Documents

By Eldon C. Pattee

Variations of a very reliable geochemical field test for beryllium developed by Patten and Ward, have been adapted by the U.S. Bureau of Mines to facilitate rapid testing of reconnaissance samples and to aid in rapid examination of known occurrences. Although several qualitative tests for detecting beryllium have been described in the literature,1,2,3, the Patten-Ward4 morin geochemical field method has the advantages of being rapid and being quantitative for minute amounts of beryllium. In addition to the morin field method, Patten, in cooperation with Griffitts, have developed a contact- print method for determining beryllium in hand specimens.5 The semiquantitative method can be used for rapid screening of samples in exploration or reconnaissance work. The use of beads for fusing samples provides a more rapid test, but gives less accurate results than the method developed by Patten and Ward. The semiquantitative method, however, requires less equipment and combines three stock solutions into one reagent for easy application. Estimates of samples in the range from 3 to 1000 ppm varied from about 0.25 to 5 times the actual beryllium content.

Jan 5, 1965

By E. H. Lancaster, M. E. Mitchell

A MUD-conditioning program found to be very effective for drilling and completion operations on routine field wells requiring relatively short drilling time involves a moderate alkaline-tannate-bentonite treatment resulting in an ultimate filtration rate of 10.0 cc or less (API test). Mud weight schedules are planned from pressure information on completed wells in producing reservoirs and drill-stem test data obtained on other zones not being produced at present. In general, terminal mud viscosities average 45 sec (Marsh). This value has been found to be sufficient to remove cuttings from the well bore on the average well, with the slush pumps in general use on the rigs. On field wells requiring drilling times in excess of approximately 30 days, an alkaline-tannate-lime-bentonite treatment has been effective in maintaining desirable viscosities and filtration rates with a substantial reduction in chemical costs. This system has shown particular advantage on heavily weighted muds and those with abnormal flow-line temperatures. For the most part, the chemical treatment utilized in wildcat drilling follows closely the program used on field wells, depending on depth and duration of drilling operations. Wildcat mud programs are planned from information available from various geologic and operational sources, taking into consideration the possibility of encountering mud problems of a special nature in the wildcat area. Careful planning of wildcat mud pro- grams has proved to have definite value in avoiding most serious mud problems. An analysis and recommended treatment are presented on several special. mud problems which have been encountered in the area in the past. Those problems discussed are lost circulation, blowouts, sloughing shale, excessive chloride contamination, sulphate contamination, and prevention and correction of cement contamination. Introduction Drilling-mud control in the Southwest Texas area, in general, does not involve the multiplicity of problems encountered in other coastal areas. For instance, it is rare that a mixture of problems such as lost circulation, abnormal pressure, severe sloughing shale, and others, occurs on one well within close enough limits in vertical depth not to be taken care of by a sensible casing program, together with a relatively clear-cut mud program. There are conditions such as the fairly widespread occurrence of abnormal pressure in the lower Frio and Vicksburg zones, and the tendency for sloughing shale in the Jackson section which make for rather expensive mud control. However, the availability of fairly accurate geologic and operational information makes possible a reasonable degree of standardization on mud treatment over a relatively large area. It may be said that, over most of this area where drilling is currently in progress, the natural mud made is very poor in quality, but responds readily to moderate chemical treatment to yield very good wall-building characteristics. AS far as field development drilling is concerned, the mud engineer's principal job, once the routine treatment best

Jan 1, 1949

THE book covers principally the assaying of silver and gold and the determination of these values in ores, sweepings, and base metal. It seems to have been written more for the goldsmith and jeweler than for the primary producer of metals. There were approximately sixty different substances needed in the operations described and not over a dozen different types of raw material (ore, matte, crude or alloyed metal) are mentioned. The methods of separation used were essentially simple and reasonably reliable, though the processes were not sufficiently understood to permit the selection of the simplest effective ingredients, and there was a great tendency to employ complicated fluxes, with unnecessary repetition of long-continued heatings indicative of a leisurely pace of life. Practically all the processes described are based on a few chemical facts: the inability of gold to combine with sulphur, while silver and the base metals form easily fusible sulphides; the ready oxidation of base metals; and the ii- solubility of gold in nitric acid. Fluxes serve to make earthy impurities fusible, and to carry oxidizing or sulphurizing ingredients. Many of the processes of assaying had changed little up to the beginning of the present century. Even as late as 1924, when the writer took a University course in fire assaying, the crucibles, cupels, scorifiers, molds, and tongs were identical with those of the sixteenth century, though the wind furnace had a stack on it and the muffle for cupelling was gas-fired.* The fluxes were purer, but of the same essential composition. That this branch- or twig-of metallurgy had not advanced in any funda-

Jan 1, 1949

By Z Chang, S A. Mrozek

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Antamina, Peru is the largest Cu-Zn skarn deposit in the world. Skarn mineralisation is focused around a multiphase Miocene intrusive complex comprising at least eight distinct phases identified by cross-cutting relationships, including truncated veins, xenoliths and chilled margins. Skarn alteration and mineralisation, as observed in drill core, remain open at depths exceeding 2.2 vertical kilometres.Porphyry intrusions occur as four major phases with subphases (from oldest to youngest): P1 (a, b), P2 (a, b), P3 (a, b) and two dykes of uncertain timing named Oscarina-1 and Oscarina-2. P1a is a hornblende-biotite quartz diorite porphyry with pervasive K-alteration, local endoskarn and 30–40 per cent sheeted quartz veins, all of which obscure original igneous textures. P1b dacite porphyry is a minor unit with <10 per cent phenocrysts and <3 per cent quartz veins. P1b cuts P1a; P2 dykes cut both units. P2a porphyritic biotite quartz monzonite contains K-feldspar megacrysts up to 4 cm long, local K-alteration and 2–80 per cent quartz stockwork veins. P2b biotite monzonite porphyry contains approximately 50 per cent phenocrysts and typically <10 per cent quartz veins. P3a (brown groundmass porphyry) and P3b (coarse phenocryst porphyry) are minor in volume and extent, and both cut P2 bodies. Oscarina dykes comprise two separate but parallel bodies. Oscarina-1 is a feldspar-phyric rhyolite porphyry, while Oscarina-2 is an intensely chloritised andesite porphyry. Oscarina-1 has a U-Pb (laser ablation inductively coupled mass spectrometry (LA-ICP-MS)) age of 10.1 ± 0.1 Ma, whereas P2 U-Pb zircon ages (LA-ICP-MS) range from 10.0 ± 0.2 Ma to 9.9 ± 0.3 Ma.All the intrusive phases contain quartz veins, with P1a and P2a having the most intensive K-alteration and most abundant quartz veins ± endoskarns. Each phase may have contributed to mineralisation at the right depths and within favourable wall rocks (ie marble) during uplift of the Antamina structural block. Therefore, a model of multiple intrusions during continuous uplift explains the vertically extensive (>2.2 km) skarn and mineralisation at Antamina.CITATION:Mrozek, S A, Chang, Z and Meinert, L D, 2015. A model for the intrusive sequence and Cu-Zn skarn formation at the Antamina deposit, Peru , in Proceedings PACRIM 2015 Congress, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

By Tanner A. C, Harraway D. H

Various circuits were tried at Mount Isa Mines during the period 1959 to 19G3 with the objective of improving the differential flotation of galena and sphalerite. Many benefits and disadvantages of the various circuits were revealed. An analysis' of ore characteristics and their effect on flotation was made -and resullted in the design of a proposed circuit which is currently in the process of installation.INTRODUCTIONSince 1936 when lead-zinc sulphide flotation commenced at Mount Isa, at least three types of ore have been encountered.Each ore has presented problems to flotation metallurgists.The three types of ore are,1. partially oxidized upper level sulphide ore,2. Black Star ore from the lower levels with its carbonaceous fraction, and3. Black Rock ore which is similar to 2, but more free milling.In retrospect a number of the metallurgical successes of the past were short lived. Often flowsheets or 0perating practices were designed to solve a single metallurgical problem associated with the current ore being treated. As the ore changed the problem would vanish and the method originally taken to counter the problem could become unnecessary or deleterious to the treatment of the new ore. The general lesson learnt from-the past-is-that thetreatment of Mount Isa lead-zinc ore involves a number of equally major problems...

Jan 1, 1963

By P. M. Gruzensky

Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step. With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C, and contained at least 100 grams of bismuth per liter, An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.

Jan 1, 1956

By J. Szekely, G. P. Martins

A formulation is given for describing the rate of expansion of spherical bubbles rising in liquids the freeboard of which is evacuated. The computer solution of the resultant differential equations has shown that, for low freeboard pressures (less than about 5 mm Hg), on approaching the free surface the bubbles expand much less rapidly than predictable from equilibrium considerations. In other words, in this region the pressure inside the bubbles will be significantly larger than the static pressure in the liquid corresponding to the position of the bubble. These theoretical predictions were confirmed by experimental work, using two-dimensional air bubbles rising in mercury. The important consequence of these findings is that the expansion of gas bubbles in vacuum degassing operations will be a great deal less than expected from hydrostatic considerations. This would lead to a significant reduction in the available interfacial area and may explain the apparent poor efficiency of many vacuum degassing units. VACUUM degassing as a treatment for liquid steel has gained widespread popularity in recent years; the number of known installations exceeds several hundred at the present time.' Although much information is available on both the thermodynamics of the system and the overall performance of various industrial units, much less is known about the fundamental aspects of the process kinetics.2-4 The basic physical situation common to virtually all vacuum degassing operations is the interaction between gas bubbles (swarms of bubbles) and the surrounding molten metal, held in a container, the freeborad of which is at a low absolute pressure. Once formed (or introduced from an external source) the bubbles will ascend, due to the buoyancy forces, and, during this ascent, a significant increase in their volume will occur. This progressive increase in the bubble volume is due to two factors: a) the continuous reduction in the static pressure acting on the bubble during its rise; and b) mass transfer into the bubble from the surrounding molten steel. In a recent paper Richardson and Bradshaw developed equations5 for describing mass transfer into gas bubbles from molten metals at reduced pressures. However, in deriving these expressions it was assumed that the pressure inside the bubble was identical to the static pressure in the adjacent liquid. In other words, the volume of the bubble was considered to be in equilibrium with the pressure of the fluid adjacent to it. This assumption, thus their analysis presented, was thought to be reasonably accurate for most of the bubble's ascent; however, it was unlikely to be valid in the immediate vicinity of the free surface, held at a low pressure. It was pointed out in the discussion6 that the region close to the surface may be of considerable importance as both the driving force and the interfacial area available for mass transfer are at their highest value here. The ' 'anomalous" behavior of gas bubbles when approaching a free surface at low pressures was recently confirmed in a preliminary investigation by Szekely and Martins. ?1 Here high-speed motion photography was used to study air bubbles rising in a column of n-tetradecane with a freeboard pressure of 0.1 mm Hg. It was found that significant distortion of the bubbles occurred on approaching the free surface; furthermore, the expansion observed was much less than what one could expect from hydrostatic considerations, i.e., factor a previously discussed. It follows from the foregoing that a detailed study of these phenomena would be justified both from fundamental considerations and because of their potential relevance to technology. The purpose of the paper is to present a more realistic formulation for the expansion of a gas bubble approaching a low-pressure region, together with a comparison of the theoretical prediction with experimental measurement. An inert bubble will be considered in the first instance; it is thought that the understanding of the fluid mechanics is an essential first step toward the realistic formulation of the mass transfer process. This latter problem will be the subject of a subsequent publication. FORMULATION The Physical Model. Consider a spherical bubble, of initial radius Ro, rising in a fluid, having a density pL. Initially let the bubble be at a distance H from the free surface, and at a pressure Pgo, as illustrated in Fig. 1. Pgo, the initial pressure in the bubble, is given by the following equation: pgo = Po = Ptp +pLgH [ la] where Po is the pressure in the liquid corresponding to the initial position of the bubble and Ptp is the pressure at the free surface. The fluid pressure at

Jan 1, 1970

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003

By Colin D. Jardine

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. A recent application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by the use of a "building block" approach to design and equipment selection. Details of this approach and the results obtained are described.

Jan 1, 1982

By P. Linehan, J. F. Wiss

Vibration and air blast noise from blasting were evaluated during a research program sponsored by the US Bureau of Mines. Blast variables were studied wing small scale model (SCM) tests to evaluate specific variables as well as interactive effects, followed by experiments with production blasts at the surface coal mines. Experimental data showed that the primary variables affecting the ground vibration amplitude are the charge weight per delay and the length of delay interval. Blast variables having a significant effect on the overpressure amplitude include the charge weight per delay, the length of delay, burden and spacing, stemming amount and type, direction of initiation, charge depth, and amount of detonating cord and cover.

Jan 1, 1983

By David Harrison, Edward J. Walter, Meitra Ferek

Agreat tool in the prevention of blasting complaints and subsequent damage claims. In today’s highly competitive industry, we are always looking for ways to become more cost effective. This article investigates the importance of pre-blast surveys-not just for regulatory compliance, but as an overall long term cost cutting and public relations tool.

Jan 1, 1995

By B. K. Shibler, A. O. Ipsen, W. W. Agey

"INTRODUCTION As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines obtained and examined samples of ore from six properties in the vicinity of Pioche, Lincoln County, Nev., and from one property near Caliente, Lincoln County, Nev. As the ores were too low-grade to be acceptable for the direct production of ferromanganese, their amenability to concentration by ore-dressing methods was investigated.In general, the Pioche ores had a low manganese content and, owing to extremely intimate association of manganese minerals with iron oxide and nonmetallic gangue, were refractory to concentration by ore-dressing methods. Only two samples (Zero Gap and Wheeler ores) were amenable to the production of concentrates that would sinter to a marketable plus 35-percent manganese grade. The Prince Consolidated and Ely Valley No. 1.ores were roasted and sintered to produce lead-silver-zinc fumes. The residues were of possible value as manganiferous iron ore. No marketable manganese products were made from Calton semi-oxidized ore, but over 80 percent recoveries of lead, silver, and zinc were made by bulk sulfide flotation followed by Diming of the sulfide concentrate. No satisfactory results were obtained by treatment of Golden Eagle and Ely Valley No. 2 ores.The Cudverwell ore was amenable to the production of high-grade manganese concentrates by ore-drssing methods. However, fine grinding was required to effect mineral liberation, and loss of manganese as slime limited the mangenese recoveries obtainable.In the coarse of the investigations, many data were obtained and compiled, but for the sake of brevity, several data, of secondary importance have been omitted or condensed, and only the tests giving the more promising results are discussed in detail. For convenience, the report has been divided into two parts, one opertaining to the Pioche ores and the other summarzing results obtained by testing Culverwell ore."

Aug 1, 1947

By D. Thibault, A. Akhiate, M. Brochu, E. Braud

Cast martensitic stainless steels, 13%Cr-4%Ni, having carbon contents between 0.018 wt% and 0.067 wt% were normalized, air quenched, and tempered at two different temperatures (550°C and 610°C). Their microstructures were characterized by optical microscopy and X-ray diffraction (XRD). Macro and microhardness, tensile strengths, and impact resistance were quantified for each material and condition. Results show that the prior-austenite grain size is constant through the materials but the percentage of reformed austenite, contained in the martensitic matrix, depends strongly on the material chemistry and on the tempering temperature and on its duration. It is observed that, independently of tempering conditions, an increase in carbon content increases the material hardness and tensile strengths, whereas the elongation remains constant. In contrast, the results of Charpy type impact toughness tests show a different trend. The material containing the average carbon content (0.034 wt%) is significantly tougher than the two other alloys. Surprisingly, the toughness of the steel containing 0.034 wt% carbon was found independent of the reformed austenite content. It is thus concluded that carbon and reformed austenite contents are not the only parameters affecting the toughness of these steels.

Jan 1, 2014

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

"The building stone industry of Utah has developed slowly on account of the limited market offered. The state has large and varied deposits of granite, limestones, marble and onyx.Three cement companies manufacture Portland cement in the Salt Lake valley. Brick clay, fire clay and clay for sewer pipe is found in the vicinity of Salt Lake City and Ogden.Large deposits of gypsum have been found in several localities in Utah. The gypsum deposit near Nephi has been developed to be one of the most important plaster producers in the western country. This gypsum occurs in large quantities and is exceptionally pure.Oil and Oil ShaleVast deposits of rich oil shale occur in the Green River formation of the Tertiary rocks in the Uintah Basin, northeastern Utah. It is estimated by the United States Geological Survey that the basin contains at least 92,159,000,000 tons of shale which will yield as much as 15 gallons of oil to the ton when distilled. These shale deposits indicate that ultimately Utah will be one of the leading shale oil producing states of the country. Some development work and considerable experimental work has been done, but overproduction of petroleum and general low prices afforded little incentive to the oil-shale operator, consequently no commercial production has yet been established in Utah."

Jan 1, 1925

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By Al Campoli

One of the critical variables affecting resin bolt performance is the size of the resin annulus, defined as the difference between the hole and bolt radius. The vast majority of the millions of resin roof bolts installed each year in the United States employ an annulus between 0.125 and 0.188 inch. As the annulus size decreases the resin flow around the bolt becomes more difficult, increasing the resin pressure induced by bolt insertion. As the resin pressure increases the loss of resin into bedding planes and vertical fractures in the rock increases. As the annulus size increases the mixing of the resin paste and mastic becomes less efficient. Thus, the lower and upper limits of the optimum annulus size is determined by insertion pressure and mixing considerations, respectively. Previous U.S. Bureau of Mines researchers have concluded that a 0 125 inch annulus is optimal. However, others have recently reported that a 0.095 inch annulus with special rolled deformation (SRO) bolts provide superior anchorage to standard rebar with a very large 0.250 inch annulus, attributing SRD resin loss in weak ground to oversized holes. The effect of annulus size on unit length pull strength and resin loss to fractured rock was investigated. Short encapsulation pull tests with resin annuluses of 0.125 and 0.095 inch resisted an average of 2.25 tons per grouted inch, with no significant variation. However, annulus size has shown a dramatic effect on the magnitude of resin lost to simulated rock fractures. No. 5 standard . No. 6 standard, and No 7 J-Bar rebar were inserted into two different viscosity resin cartridges designed for 4 foot boll encapsulation into a one inch inside diameter metal tube, To simulate a rock fracture, a 0.250 inch diameter orifice was located near the capped end of the tube Resin loses increased as annulus size decreased, with a minimum loss of 35% and a maximum loss of 60% associated with 0.125 and 0.095 inch annuluses, respectively.

Jan 1, 1999

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995