Search Documents

By C. A. Stetefeldt

The hacienda Sauceda is one of the largest and finest haciendas in the vicinity of the City of Zacatecas, Mexico, and is said to reduce ores by the Patio process more cheaply than any other establishment. It receives its supply of ore from the San Acacio mine. This mine has been for some time, like most of the Zacatecas mines, out of bonanza, and yields, at present, ore of rather low grade. The silver occurs principally as silver-glance, ruby-silver and native silver, associated with pyrites of iron and copper, and some galena and zinc-blende, in a gangue of pure quartz, which takes the form of amythyst whenever the ore is of high grade. All the ore, as it comes from the mine, is broken by hand into small pieces, and sorted before it is delivered to the hacienda. Here it is first crushed dry in Chili mills, and then ground wet in arrastras to an impalpable powder. The sulphurets not decomposed in the patio process are separated in the settlers from the tailings and concentrated by hand. By roasting them in a reverberatory furnace with carbonate copperores, "magistral" is obtained. All machinery is driven by mulepower.

Jan 1, 1885

By M. A. Selim, W. H. Somerton

Thermal expansions and heats of reaction of three typical sandstones were measured in the temperature range of 25°to 1,000°C. The significance of these data in subsurface heat-transfer calculations is discussed. Linear thermal expansions were measured both parallel and perpendicular to the bedding planes. Volume expansions are reported as the perpendicular expansion plus two times the parallel expansion. Expansion behavior of the sandstones was found to be controlled by the expansion characteristics of the quartz content. Differential expansion of the quartz grains and other minerals included in the sandstones caused permanent deformation of the heated samples after they were cooled to room temperature. Structural damage resulting from heating is probably an important cause of the reduction of thermal conductivity of heated samples. Measurements of heats of reaction were based on the known heat required for a- quartz inversion. Thermal reactions, which probably include deby-droxylation of clay minerals and decomposition of carbonate minerals contained within the samples, were found to require more than one-fourth of the amount of heat necessary to raise the temperature of the rock alone. In shales and limestones, the reaction heat could be substantially greater than that required from specific heat considerations alone. INTRODUCTION In earlier work, l-3 methods of measuring thermal properties were developed and thermal data for several sedimentary-rock types were reported. Data included thermal conductivity, specific heat and thermal diffusivity. In addition, calculations of heat transfer in subsurface formations may require data on the thermal-expansion characteristics of rock and the heats of reaction of mineral constituents. Thermal expansion of rocks is relatively small in magnitucle and, from the standpoint of change in bulk density, has only minor effects on heat-transfer cliaracteristics. Thermal-expansion behavior, however, may have significant effects on the structure of rocks. Differential expansion of different minerals and along different crystal-lographic axes may result in structural damage which could effectively reduce the thermal conductivity of the rock. Many mineral constituents of sedimentary rocks undergo phase or related changes when heated to sufficiently high temperatures. Although some of these reactions (such as the a-ß quartz inversion) are reversible and the heat absorbed is returned to the system upon cooling, many of the major reactions are irreversible. Through certain temperature ranges, the additional heat energy required to complete the reactions may be nearly as great as that necessary to raise the temperature of the rock in the absence of thermal reactions. If the heat requirements for these reactions are not considered, serious errors in heat-transfer calculations may result. Thermal-tzxpansion and thermal-reaction data have been obtained for three typical sandstones. Methods of measurement and results obtained are reported and discussed in the following. THERMAL EXPANSION OF SANDSTONES The linear expansions of three outcrop sandstones (Bandera, Berea and Boise) have been measured in the temptbratue range of 25° to 1,000° C. Expansion measurements were made in the directions parallel and perpendicular to the bedding. The differential expansion apparatus used is that described by Mitoff and Pask.4 The test sample is heated in an electric furnace with a temperature rise of 6°C/minute. The lengthening of the samples upon heating is compared with the small and known expansion of a fused silica rod. The change in length is transmitted to an X-Y recorder by means of a Statham transducer. A maximum error of ± 1.5 per cent has been obtained with this apparatus

By Robert N. Roby

The Hornsilver lead-zinc property was examined by the Bureau in 1942 and again in 1944. A project was started on the property in April 1946 and completed in January 1947. Silver was first discovered in this district in 1883, and while complete production records are not available, it is known that a substantial tonnage of high-grade silver ore was shipped before 1887. All of the ore was mined from surface or near-surface workings. When the high-grade oxidized ore was exhausted, the district became inactive and remained so until the 1920's. In 1928 and 1929 some activity was shown in the district, but the Hornsilver mine was not reopened until November 1937. Between 1939 and 1946, the mine produced about 16,000 tons of ore of 531 ounces of gold, 283 ounces of silver, over a million pounds of load, and nerdy 2 million pounds of zinc. The property is now controlled by the Era Mining & Development Co., which has acquired the Last Chance and Ella groups of claims, in addition to the Hornsilver mine.

Jan 1, 1948

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By L. T. Larson

Had the blank on the Abstract form been sufficiently spacious a more appropriate title for this paper would be: Neogene Tectonism, Magmatic Activity and Hydrothermal Precious Metal Mineralization in Anatolian Turkey; an Analog with the Basin and Range Province of the Western U.S.? Like the alternative title no thing in Turkey is simple. Its history is long and convolute; its culture fascinating; its metallogeny diverse and its geology very complex. This paper will focus only on the geology of western' Anatolia and the precious metal potential of this third of Turkey. The argument is in the article but to save the reader time and suspense I'll put my conclusions up front- the potential is great and the possibilities exciting.

Jan 1, 1989

By T. Clarkin

This paper presents a hydrologic closure design concept to minimize the risk of water discharges from closed mine tailings facilities. It evaluates the applicability of U.S. Nuclear Regulatory Commission guidelines to develop acceptable designs for the closure of tailings facilities that have a calculated adequate surcharge capacity for environmental protection and an emergency spillway for dam safety. The guidelines provide a basis to estimate an acceptable surcharge capacity of a Probable Maximum Flood series for storage of surface runoff. To be conservative and for redundancy with respect to dam safety, an emergency spillway is provided to pass the Probable Maximum Flood. Depending on the annual water balance, the surcharge capacity may be used by surface runoff and minor amounts of sediment that accumulates in the impoundment from year to year. The emergency spillway crest is then set at this level or above the surcharge capacity, whichever is higher. An example is given of the active Red Dog Mine tailings facility in Alaska where this method was used for the preliminary design of the tailings main dam at its ultimate closure configuration.

Jan 1, 2012

The Rosebery and Hercules mines, situated in the Rosebery-Williamsford district in western Tasmania, have a history of production dating back to 1896-7, although full scale production did not commence until 1936, following the development of a satisfactory process of selective flotation (Hall, Cottle, Rosenhain and McGhie, 1953). The mineral composition of the Rosebery zinc-lead ores was first described in detail by Stillwell (1934). The Hercules ore is generally similar, but as yet no descriptions of it have beenpublished.Since Dr. Stillwell's paper appeared, the management of the Rosebery and Hercules mines has from time to time submitted a number of interesting mineral specimens to C.S.I.R.O. Mineragraphie Investigations. Examination of these specimens brought to light eight minerals, some relatively uncommon, not previously recognized in these ores.They are cassiterite, molybdenite, stannite, electrum, meneghinite, boulangerite, pyrargyrite and pyrrhotite. Some of the specimens are also rich in tetrahedrite and gold. In addition each of the other ore minerals described by Stillwell, viz. pyrite, sphalerite, galena, bournonite, chaleopyrite and arsenopyrite, was detected in one or more of the specimens examined during the present study. The principal gangue minerals were found to be quartz, manganiferous carbonate, sericite and barite, agreeing closely with the observations of Stillwell.The present study was based on the examination of the following eight specimens.

Jan 1, 1960

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By R. Leithner

The need/wish to sequestrate CO2is based on the assumption of the International Panel of Climate Change (IPCC), that CO2 maybe the major driver in climatic changes, i.e. especially the anthropogenic CO2emissions due to the combustion of fossil fuels like coal, oil and natural gas will increase the atmospheric CO2-content, which will lead to higher temperatures in the atmosphere. The 0.03% CO2in the atmosphere have a 22% share of the natural greenhouse gas effect of 33 K necessary for life on earth. The main share of 62% has the water vapour in the atmosphere. Only if one concentrates on the greenhouse gas effect of the gases beside water vapour, CO2 becomes most important with 58% influence. In addition there are other influences on the climate like: • Eccentricity of earth’s orbit, precession of orbital plane, obliquity and precession of earth’s rotation axis (Milankovitch’s theory) • Sunspots and magnetic field of the sun • Changing streams in the ocean • Volcanic activities • Distribution of continents on the surface of the earth • Impact of meteorites • Change of insulation by interplanetary dust [Muller, R.A. 2000] etc. To answer the question, if the CO2-content in the atmosphere has an important or exclusive influence on the earth atmospheric mean surface temperature, one should look into history. Figure 1shows the mean temperature of the atmosphere and the atmospheric CO2-content time histories 1 billion years back; no correlation can be found between them. Nevertheless a lot of countries have committed themselves to reduce their CO2-emissions.

Jan 1, 2004

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By S. C. Termes

The Bureau of Mines has used Fourier transform infrared spectroscopy (FT-1R) to study in situ reactions of aqueous solutions of potassium ethylxanthate with CU(II)-and Pb(II)-activated sphalerite plates, in which the plates were both the infrared-transparent windows and the reacting surfaces. A copper (I) ethylxanthate formed predominantly with Cu(II)-activated sphalerite, regardless of the activation time. The products formed on Pb(II)-activated sphalerite depended on the activation times; a short activation time (30 min) yielded a lead ethylxanthate-like product, but a long activation time (90 min) yielded a considerable amount of dixanthogen.

Jan 1, 1986

By Carlos Herrera, Paulo Alcazar, Alex Conco, Fremy Flores

Las redes neuronales artificiales son un subconjunto del machine learning y están en el corazón de los algoritmos de Deep learning reflejando el comportamiento del cerebro humano, permitiendo así que las soluciones tecnológicas reconozcan patrones y resuelvan problemas comunes en los campos de la IA. Este modelo matemático es capaz de aprender a través de un aprendizaje supervisado de patrones de conocimiento. Se investigó una solución que involucra cuatro tipos de sistemas.

Sep 30, 2022

By William F. Hahn

This report describes an illumination system suitable for use in a slope under construction, Simulator work was performed using actual lighting hardware to verify adequate light levels to meet MSHA proposed regulation (as published in the Federal Register, January 13, 1977). The sequence of operating activities for two different slope driving sites are discussed and lighting requirements are defined for each,

Jan 1, 1981

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By J. H. . MORGAN

Talc-soapstone deposits exist in Patton Township of Quebec and have been mined by Bakertalc Inc. or its predecessors since 1938. The company produces products ranging from purified and micronized talc through to soapstone lumps. The deposits are found within serpentinite dykes and are zoned. Zoning grades from a serpentine core through zones of talcmagnesite, schistose talc and talc-chlorite schist be/ ore reaching the wall rock of quartz-sericite-chlorite schist. Talcmagnesite zones generally comprise 80 to 90% of the mined rock. The serpentinite dykes containing the talc probably were originally post-Ordovician peridotite of the same series that hosts the Eastern Townships asbestos deposits. Alteration of serpentine to talc-soapstone and magnesite apparently resulted through addition of silica and carbon dioxide along shears and fractures. Talc concentrations occur also at the intrusive contact between dykes and wall rock. The present Bakertalc Inc. operation at the Van Reel Mine is being worked from an inclined shaft 200 m below surface. The talc rock undergoes a variety of milling processes, depending on its particular market, be/ ore being bagged and shipped.

Jan 1, 1984

By Beatryz C. Mendes, Márcio Sampaio S. Moreira, Rita de C. S. S. Alvarenga, Juliano Correa

Over the last decades, modern technology to build wood structures have been substantially developed. Building solutions for floor systems of wood-concrete mixed T-beams with wood web and concrete flange stand out among these technologies. This work describes an experimental investigation of the performance of bond connectors made of round steel bars for wood-concrete mixed elements. Symmetric three-member specimens were built. The middle member was made of concrete and the other two were made of wood. The first kind of connector consisted of steel bar designed as straight pins with head, normally driven through the wood. The second kind consisted of arc-shaped connectors directly embedded into the wood or bonded using epoxy adhesive. The specimens were then tested in compression. The compressive strength and the force-displacement curve were obtained, in order to evaluate the failure mode and obtain the stiffness in the ultimate (Ku) and serviceability (Ks) limit states. The stiffness values were calculated in the interval corresponding to the secant straight line between, respectively, 10–40 and 10–70% of the ultimate strength. The obtained results indicate high strength and ductile failure mode for all of the cases. Bond stiffness gains were verified when using the arch-shaped connectors.

Mar 1, 2017

By Walker BV

Mining activity has been an integral component in the New Zealand economy since the early days of European settlement. Recently in common with other Pacific Rim countries there has been a resurgence of investment in gold. A sustained and increasing exploration effort has resulted in the rapid development of alluvial gold mining operations, a number of hard rock gold discoveries, and a general optimism about New Zealand's prospectivity. New Zealand's attitude to mining development, in particular hard rock gold mining is influenced by high environmental values and a concern, largely through absence of examples, that modern mining may not perform to community standards. While these environmental concerns are wide spread there is a growing realisation that gold mining, if properly managed, can take place within acceptable environmental standards and that it has the potential to contribute significantly to New Zealand's economy. New mining developments have an important role to play in this process. The mining industry in New Zealand is now at a crossroads. Having invested substantially and confirmed the potential for gold mining developments it has found itself in a rapidly changing economic environment as the Labour Government puts in place a number of fundamental economic reforms. The reforms are intended to free up the economy removing the rafts of subsidies and protective measures which have stultified initiative and growth. A fundamental reform of the public service has been initiated including corporatisation of trading activities and the establishment of a Department of Conservation to administer estensive areas of Crown land. Both petroleum and mining taxation are being reviewed with the intention of creating a more neutral competitive environment. Mining legislation is also being re-examined with both efficiency and equity objectives. While the current environment is characterised by uncertainty and rapid change, the outcome will be a more market-oriented stable policy environment, to the mutual benefit of the industry itself and the New Zealand Community.

Jan 1, 1987

By Joseph Hodgson

IN 1880, mining operations were commenced at the Copper Queen mine. The famous Queen orebody, which extended to the surface, was first quarried from a large open cut in the outcrop. The orebody was followed down to the 300 level with the Queen incline, and stoped. This, we believe, marks the introduction of square setting in the Bisbee district, which is still the method most generally used. Orebodies The orebodies in the Copper Queen mine occur in the limestones, and the main portion of the ore has been mined from the Abrigo, Martin, and. Escabrosa limestones. While the orebodies outcrop in the extreme western end of the mine, the general dip is to the east and south, at an angle of about 20°, although this dip is not by any means regular, being, in fact, very irregular locally. The ore is remarkable for its variableness in character, some of it being very soft, requiring a large amount of timber, and other portions consisting of extremely hard sulphides. The orebodies, in general, While remarkable for their continuity, are very irregular, both as to shape and size. The mine having been in operation so many years, and mining having been prosecuted over such a large area, the operations have caused the shrinkage of the overburden, and there is a constant movement, which is shown y large cracks and interstices in the surface rocks, which largely contribute to the very high deadwork or maintenance cost of the mine. It is surprising that for year 1913 it cost almost $400,000 just for the one item of repairs and deadwork in this property.

Jan 8, 1914