Search Documents

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971

By Daniel Johansson, Markus Danielsson, Håkan Schunnesson

In sublevel caving, blasted material flows gravitationally into the drawpoint from above in a periodical manner. This type of flow behavior entails muck pile conditions that are variable along the course of extraction. The effect of this variability on the LHD (Load-Haul-Dump) operation in terms of loading efficiency and ability to undermine the blasted ring is not fully understood as of today. This paper presents results from a field test in LKABs Malmberget mine in Sweden, where the influence of fragmentation on the loading operation has been studied in detail. Drawpoint filming was conducted for extraction of two rings equivalent of roughly 10000 metric tons (~9842 long tons) of material each. The analysis includes fragmentation measurements, muck pile classification, and general estimations in terms of loadability. Further, an evaluation of LHD machines from two different manufacturers was conducted to identify and highlight differences. The results show that fragmentation, muck pile compactness, and flow characteristics are all interdependent. Flow disturbances and the subsequent loading of compacted fine material in the back of the ring have been identified as the main reason for occurring problems and prolonged digging times. However, the ability to sufficiently undermine the blasted ring has been identified to primarily depend on digging depth which is only observed to be high during flow disturbances. An absence of flow disturbances seem to promote high loading efficiency but simultaneously limit the maximum digging depth. A mid-range particle size distribution with a low amount of fines has proven beneficial for overall loading efficiency. The various LHDs employed showed significant variations in terms of ability to handle difficult loading situations (e.g. compactness, boulders, etc.).

Jan 1, 2018

By Paul Cartwright

A rockbolted roadway risk assessment procedure has been developed specifically for the Parkgate seam at Thoresby Colliery by Rock Mechanics Technology and colliery engineers. The purpose of this assessment is to identify any areas of significant risk in relation to roof instability due to potential failure or overloading of the rockbolt support system. This allows appropriate additional support to be installed in sections of roadway considered to be at increased risk. The assessment of risk in rockbolted coal mine roadways, in terms of fall of material, has to be based on an understanding of the rock mass behaviour at that site. The development of an appropriate risk assessment system is therefore site specific. A consistent approach to developing such a system can, however, be applied by adopting the same general logic to each individual site. The use of risk assessment to categorise areas with increased risk of roof instability has been undertaken for four longwall panels at Thoresby. The procedures used for these assessments are discussed and the operational benefits examined. The approach successfully used at Thoresby has been developed into a routine tool to assist mine personnel in assessing areas of potential roof instability in rockbolted roadways and as a means of communicating the position of these areas to both supervisors and workmen. The system provides a rational and objective interpretation of the current underground conditions based upon a logical, consistent and structured approach.

Jan 1, 1999

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By A. J. Farstad

Recent advances in microcomputer technology have opened the way for systems which can track the location of underground mining personnel from the surface. A computerized system has been designed which is capable of not only tracking the location of the miner but also of monitoring underground parameters, communicating between work stations and sounding alarms when underground conditions are judged to be unsafe. For the system described herein, the locations of the underground personnel are detected by a network of underground terminals which routinely emit RF pulses to interrogate miniature transponders worn by the miners. Each transponder is uniquely programmed to delay its response in such a way that the RF terminal can identify the individual transponders by the time slots in which the responding pulses are received. The underground terminals are then interrogated by the host computer on the surface which keeps a running account on underground mine conditions and personnel. The underground portion of the system is designed to operate even during mine emergencies, deriving its power from rechargeable battery supplies which are float charged during normal operation. Nine mines were visited on this program and the industry reaction to the system was generally favorable. By slanting the system design for daily use in the mine, the chance of its acceptance by the industry is enhanced. Furthermore its likelihood of being operational in the event of an emergency is significantly increased.

Jan 1, 1981

By S. J. Leach

The possible solution of some of the problems raised in H. L. Hartman's article "Determining Ventilation Requirements for Continuous Miners," which appeared in the March 1962 issue of MINING ENGINEERING, is offered by recent investigative work done at the Safety in Mines Research Establishment, Ministry of Power, Sheffield, England. Highlights of this research are outlined here. Accumulations and layers of methane form in a mine roadway because it is difficult to mix methane with air beneath it by turbulent diffusion. Such mixing involves work contrary to buoyancy forces. In specifying requirements for good ventilation it is not, therefore, sufficient to state that the airflow must be turbulent in the absence of methane. Fundamental work at SMRE on the behavior of methane roof layers has led to the formulation of rules for controlling methane roof layers which specify the ventilation velocity needed to ensure adequate mixing in terms of the rate of flow of methane into the layer (V = cu ft per min) and the airway width (D = ft). A "layering number" for methane and air has been defined by [U37/V/D] where U is the mean ventilation velocity in ft/min in the upper half of the airway. In a horizontal airway there is no mixing by turbulent diffusion for values of the layering number less than about 2, resulting in extensive roof layers. But with a layering number of 5, the layer is "brought under control"-i.e., a further increase in the layering number will shorten the length of the layer only slightly, and a small decrease in the layering number will cause only a small increase in the length of the layer. In a sloping roadway with uphill ventilation, higher values of the layering number are needed to achieve this "controlled" condition; the values range from about 5 at small slopes to about 8 at a slope of 1: 10. In downhill ventilation it is possible for layers to "back" against the ventilation, i.e., to flow uphill. The critical condition for preventing backing can also be expressed in terms of the layering number. Backing will be prevented if layering numbers are about 3 for small slopes and about 4.5 for large slopes; these values for downhill ventilation also give good control of the layer.

Jan 10, 1962

By B. C. Haimson

The Committee on Rapid Excavation of the National Research Council has recognized in its 1968 report the need for "improvement of rock-mechanics techniques for measuring subsurface stress field in deep boreholes and for determining stress distribution in walls of underground excavations". The technique recommended in this paper as being most suitable for both deep hole and tunnel wall stress determination is Hydraulic Fracturing. Using this method stresses are calculated directly from the fluid pressures necessary to initiate and extend a fracture away from a borehole. Stress determination by hydraulic fracturing is rather insensitive to inhomogeneity or anisotropy, is not limited in depth except by the length of the hole, requires simple equipment which is commercially available, and can be carried out by unskilled personnel. The method has been worked out theoretically and extensively tested and verified in the laboratory. A number of field tests in deep holes ranging from 300 to 6300 ft have yielded surprisingly good results. Preliminary underground tests have been very encouraging and most recent measurements in a tunnel complex at the Nevada Test Site yielded stresses that were both consistent and reasonable when compared with the expected directionsand magnitudes. It is recommended that hydraulic fracturing be considered as a method of in-situ stress measurement both in the pre-excavation stage of design and during tunneling.

Jan 1, 1974

By E. C. IBBOTSON

THIS process was reported upon by the Canadian Commission in 1904, and much detailed information was also given in a paper by Chief Engineer V. Engelhardt.1 Believing that some of the latest particulars of the process will be of interest, I submit the following data. At Gysinge in Sweden during the year ending May 31, 1906, from a fixed furnace giving 1 ton (2,240 lb.) of steel per tap, there were produced 950 tons of tool-steel and special steel ingots. . In carbon and iron tool-steels all the usual tempers were made. The bulk of this steel was made from charges composed of about 80 per cent of Swedish white pig-iron and 20 per cent. of steel-scrap. The percentage of carbon was regulated by the addition of briquettes. Other charges were made from Swedish white iron and steel-scrap. The average time taken per charge, for the year, when adding briquettes, was 7* hr., and the electric energy consumed was 1,128 units (kilowatt-hours) per ton. The average time per charge for white-iron and scrap charges was 5.5 hr., and the electric energy consumed was 886 units per ton. These consumptions include all time and energy lost from various causes, such as bad water-supply, ice, etc. It is quite ordinary practice to complete the charges with briquettes in 6.5 hr., and without briquettes in 5 hr., as shown by the following typical charges White pig-iron, 1,457; steel-scrap, 439; briquettes, 220; ferrosilicon (50 per cent. of silicon), 17 ; ferromanganese (80 per cent. of manganese), 15 lb. ; and aluminum, 1 oz.=

Nov 1, 1906

By Robert W. Metcalf

Corundum, natural alumina, or aluminum oxide (A1203) is the hardest mineral known except diamond. Theoretical composition is Al 52.9 percent and 0 17.1 percent, but it always contains small quantities of impurities, chiefly silica, iron, and lime. The melting point of corundum is above 1950° C., and it is insoluble in the strongest acids. Its hardness (9 on the Mohs scale) varies slightly according to purity, and its specific Gravity ranges from 3.95 to 4.10, 4 being a fair average. The index of refraction is 1.760 to 1.768 and its streak is white. Luster is adamantine to Vitreous, come specimens pearly, and color varies widely from white, gray, pink, and blue to black, brown, or bronze. Gem varieties are transparent or translucent, and of more brilliant coloring - red, blue, yellow, purple, or green. Corundum occurs in opaque massive or block structure with parting planes little developed or only roughly delineated and in granular form as minute crystals or small, irregular grains interspersed throughout the contact zones of schists and gneisses.

Jan 1, 1944

By T J. Sheer

Water vapour refrigeration (systems using water as the refrigerant) could potentially be used to provide chilled water at underground locations in mines, as an alternative to conventional refrigerators using refrigerants such as R-134a. The use of water as both the primary and secondary refrigerants is attractive in concept since direct-contact heat exchangers could be used, yielding higher coefficients of performance. The disadvantage of water is the very high specific volume of the vapour at low pressures, which leads to great challenges in compressor design, as has been reported previously in the context of slurry-ice plants for mine applications (Ophir and Koren, 1999). Steam ejectors have long been known as alternative compression devices for refrigerators, but no work has been done previously on the possibility of using ejectors powered by high-pressure water, which is readily available in mines from long pipe columns in vertical shafts. This paper presents the results of a laboratory investigation into the use of high-pressure water as the motive fluid in an ejector refrigerator. No previously reported liquid ejector system has achieved subcooling of the process fluid, ie a reduction in fluid temperature within the evaporator to a level below that of the motive fluid. In contrast, the present work demonstrated that subcooling could occur at motive water pressures above 5 MPa. Mine cooling applications were considered and it was concluded that while this concept would not be feasible as a mine-wide cooling source, there could be specialised applications where it would be beneficial. One application would be to cool backfill and thereby reduce the heat load at the working face. In this case the best performance would be achieved by using the ejector in combination with an energy recovery system such as a Pelton turbine or a three-chamber pipe feeder.

Jan 1, 2005

By L. G. Austin, P. T. Luckie, R. R. Klimpel, R. S. C. Rogers

1. INTRODUCTION The Bond method(1.2) for sizing tumbling ball mills has been used successfully for many years. The primary purpose of the Bond calculation is to predict the mill size and mill power to give a desired capacity (Q tph) from a wet overflow ball mill in normal closed circuit operated with a circulation ratio of 2.5. The input to the calculation is the make-up feed size characterized by the 80%-passing size in micrometers (xG), the desired circuit product size characterized by the 80%-passing size (xQ), and an empirical grindability number (the standard Bond Work Index) determined by a standard test. A series of empirical correcting factors(2) are used to convert the results to open-circuit or dry grinding in grate discharge mills. The Bond method has two major engineering advantages: (i) it is very simple; (ii) experience has shown that it works for many circumstances, as a reasonable approximation, because it is based on direct conversion of test data to results measured on industrial mills. There are four main disadvantages of the Bond method. First, there will be a range of error for any specific mill and material and set of operating conditions because the method does not explicitly include several variables which are obviously important: (i) recycle ratio and classifier efficiency (ii) mixture of ball sizes in the mill (iii) variations of residence time distributions with mill geometry and slurry density (iv) lifter design (v) slurry rheology (vi) different underfilling or overfilling of the mill as flow rate is changed. Second, the Bond method explicitly assumes that specific grinding energy E is not a function of ball load, whereas industrial practice and laboratory tests(3) show that the specific grinding energy (to go from a specified feed to a specified product) is less for lower ball loadings than the ball loading for maximum mill capacity. Third, the method uses only the 80% passing size of circuit feed and product to characterize the size distributions, whereas mill capacity in general must depend on the shape of the feed size distribution and the product size distribution. The prime example of this is the use of the reverse closed circuit which removes some fraction of the make-up feed before it is

Jan 1, 1982

By Khosrow Ebrahimi

We document the occurrence, mineralogy and firing properties of magnesite from hydrothermal deposits in the upper Cretaceous ophiolites of Eastern Iran. These deposits occur as thin veins of nearly pure cryptocrystalline magnesite with only trace amounts of quartz, calcite, and dolomite. Ratios of CaO/SiO2 in the bulk ore are variable. The composition of dead-burned magnesite from these deposits, calcined at different temperatures and durations, is predictable from phase equilibria. Textures of the calcined magnesite were studied by SEM; results show that the principal impurites produced during calcination are forsterite, monticellite, merwinite, dicalcium and tricalcium silicates, and that these are located principally at triple junctions of the periclase crystals. The size of periclase crystals increased with temperature and duration of calcination and the amount of periclase-periclase grain contacts was reduced by increasing the concentration of impurities in the starting products. EPMA show: 1) that CaO and FeO contents in periclase increase steadily with an increase in the CaO/SiO2 ratio and the FeO content of the bulk ore, respectively, and 2) that limited solid solution exists between impurites. This study demonstrates that high quality dead-burned magnesia refractories can be produced from the Iranian magnesite with low CaO, SiO2 and FeO contents.

May 1, 2004

By Jorge Madias

La mayor parte de las máquinas de colada continua de palanquillas que utilizan buzas calibradas y lubricación con aceite se operan con alta velocidad de colada en secuencias largas, obteniendo alta productividad. Muchos de ellos todavía practican la inyección de aluminio en el molde, para desoxidar el acero líquido sin riesgo de obturación de las buzas. También es todavía usual la práctica de “pescar” la nata que se forma en el menisco. Las salpicaduras del chorro de cuchara contribuyen a la formación de chanchos en el repartidor, requiriendo el lanceo con oxígeno. Alternativamente, diversas plantas prefieren utilizar tubo de protección entre cuchara y repartidor y protección con gas inerte del chorro del repartidor al molde en todos los grados de acero colados con buza calibrada. Se hace una comparación entre ambas prácticas desde los puntos de vista de inversión, costo operativo, seguridad, productividad y calidad.

Jul 30, 2018

By R. E. Hobart

THE development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines; led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was a 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means, of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 2, 1918

By B. K. Larkin

Solutions to the diffusion equation for a line source located anywhere in a region bounded by a circular discontinuity are presented. Such solutions follow automatically from the Green&apos;s function presented by Jaeger.4 Petroleum industry applications of this problem would include transient compressible fluid flow in porous media bounded by a discontinuity. Since several recent papers have treated the subject in less general form, it would appear that many workers in this area of the petroleum industry are not aware of Jaeger&apos;s work. STATEMENT OF THE PROBLEM In several trearments1,2,3 of the transient flow of compressible fluids in porous media it was convenient to consider a region to be bounded by a circular discontinuity. In such a region (Fig. I), the properties in Region 1, r < a, are constant but different from the properties in Region 2, r > a. Hurst, l using the Laplace transform, obtained solutions for a line source located in the center of such a porous medium. The purpose of this work is to point out that a much earlier paper by Jaeger4 presents the solution for a line source located anywhere inside the discontinuity. The assumption is made that a line source may be used to approximate a well. In the following material it is convenient to use the terms source and well as being equivalent; however, the reader should remember the distinction in applications. SOLUTIONS Jaeger presented the Green&apos;s function for a line source, or well, in the composite region shown in Fig. 1. In the most general form, the solution for a system of j wells in Region 1, each producing at a time varying rate, qi (t), is

Results of flotation tests on lead-zinc ore from Broken Hill, N.S.W., confirmed that flotation at pH 9 in the presence of cement gave poorer metallurgical results than flotation at pH 7. Additions of 2 kg/tonne wood raspings [e.g. blackbutt (Eucalyptus pilularis), blue gum (E. saligna), brushbox (Tristania conferta), or turpentine gum (Syncarpia laurifolia)l had little effect at pH 7 but greatly accentuated the deleterious effect of cement at pH 9. This was shown to be caused by e:xtractives (e.g. polyphenols and carbohydrate materials) derived from woods at pH 9. The proportion of extractives, as shown by DV absorbance spectra, increased with increase of pH and was affected by various salts.Additions of 1 kg/tonne Al2(S04)3.16H20 when cement or cement and wood were present showed that metallurgical results obtained by flotation were then very simHar to those in the absence of cement or wood or both. This was ascribed to lower pH values in the presence of aluminium sulphate and possibly to specific chemical effects.Additions of aluminium sulphate appear to offer an economic solution to the problem of treatment of ores contaminated with cemented fill at Broken Hill.

Jan 1, 1974

By AIME AIME

FEATURES of the second fall meeting of the Petroleum Division for 1941, held at the Ambassador Hotel, Los Angeles, Oct. 29-30, were the forum on the Paloma Plan on Thursday after- noon, the large attendance from east of the Rockies, and the dinner on Wednesday evening sponsored by the Southern California Section and at which President Suman spoke on the strategic minerals and metals situation. The attendance was large and the technical fare uniformly good ; the presiding officers had the proceedings well in hand at all times and kept things humming. Some- times it was necessary to taper off the discussion because of pressure on time. All this was due to careful groundwork before the respective sessions. These presiding officers deserve citation: L. W. Huebel, Howard Pyle, E. K. Parks, Carlton Beal, E. G. Trostel. R. W. French, Jr., John Dodge, and H. N. Marsh. The Los Angeles local commit- tees and the Southern California Section deserve much credit for the arrangements, which were recognized by suitable resolutions at the end of the meeting.

Jan 1, 1941

By John H. Hall

The Frémont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about # by 6 by about 16 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Frémont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. In testing coupons cut from castings heat treated by quenching and annealing, attention was drawn to the wide variations in the value of the Frémont test of specimens cut from different parts of the coupon. The latter was of the form and dimensions shown in Fig. 1, and Fremont test pieces were cut from two parts of this coupon, marked A and B in that figure. The results of the tests are shown below, tests A and B in each instance being from the same coupon: A. B. A. B. Coupon. Kilogram- Kilogram- Coupon. Kilogram- Kilogram- meters. meters. meters. meters. 1,........ 12.0 12.5 9,........ 27.5 32.5 2,........ 11.0 32.5 10,........17.5 31.0 3,........ 11.5 30.0 11,........ 14.5 31.0 4,........ 20.0 33.0 12,........ 15.0 27.5 5,........ 17.5 33.0 13,........ 19.0 30.0 6,........ 17.5 20.0 14,........ 17.5 25.5 7,........ 17.5 13.0 15,........15.0 30.0 8,........ 10.0 30.0

Jan 1, 1914

By J. D. de V. Louw

Introduction Zircon is a natural occurring mineral and may exhibit natural low level radioactivity. It contains trace levels (90 to120 pCi/g and 110 to 115 pCi/g respectively or 3.3 to 4.4Bq/g and 4.1 to 4.3 Bq/g) of naturally occurring radioactive uranium and thorium. This mineral is often found in a suiteof minerals (rutile, ilmenite and monazite) Due to the overlap in physical properties of monazite (containing 4–7% thorium) with some of the zircon (slight magnetic susceptibility) it often contaminates the zircon, adding to the levels of thorium in the product. Hazards associated with the products from zircon and its processing is inhalation of respirable dust (generated by milling) containing radioactive uranium and thorium which may cause cancer of the lungs. Legislature regulates the transport, use, workplace environment exposure and storage of radioactive material. In America the general regulation for the unlicensed use of low levels of radioactive materials limits the concentration to 500 ppm (U plus Th). Europe (IAEA) specifies a limit of10 Bg/g (Bequerels per gram) on the parents for transport only which is a higher level of U+Th. Companies selling into these markets need to comply with these regulations and certification is therefore required, not only of the major constituents determining the price, but of the U and Th levels as well. Exceeding the limits for U and Th may result in material being returned to the country of origin. However, for the analyst the requirement is to analyse for these elements throughout the production process as well as the analysis of the ‘tails’ that is returned to the mine area. This requires a wide range of concentration to be analysed. Methods of analysis A wide variety of methods exist for the analysis of U and Th in a range of matrices. (Table I) All these methods have been used with varying degrees of success in terms of accuracy. Overall precision for the different techniques varies from 5 to 25% relative. Time to produce results from these methods vary from a few minutes to several days. The Production Chemist is expected to produce between5 and 10 analyses per hour for process control purposes. A suitable technique that fits this requirement is X-Ray Fluorescence. Both Wavelength Dispersive (WDXRF) and Energy Dispersive X-Ray (EDX) instruments are suitable. X-Ray analysis in general has a few major advantages over competitive techniques. •It is fairly simple to set up and interferences are known and easy to correct •It has multi-element analysis capabilities •Clean spectral lines for U and Th (in zircon specifically) •Uncomplicated and easy to measure background •Low detection limits (3 to 5 ppm) •A very high degree of precision •Sample preparation is uncomplicated and fast (pressed powders and fused beads). In Zircon (ZrSiO4) processed sands the matrix is constant(>99% ZrSiO4) and the background is thus essentially constant. A typical set up for the analysis of U and Th by WDXRFis given below: X-Ray Tube Tungsten (W) Target, 2.5 to 3kW operated at 50mA/50kV Crystal LiF200 (or LIF220 for higher resolution) Analytical Lines (2?)U La1,226.14Th La1,227.47 Detector Scintillation Counter Analysis time, depending on the concentration can vary from as little as 20 seconds up to 5 minutes. Standards As with any other comparative technique XRF analysis relies heavily on the quality of the standards used. Assuming proper set-up and operation of the instrumentation as well as consistent sample preparation, accuracy is determined by the quality of the initial calibration standards. A search for the available zircon certified reference materials (CRMs) shows that there are only a few CRMs

Jan 1, 2003

By Theodore J. Hoover

WHAT are the chief branches of the mining engineering profession today? In an effort to analyze the structure of the profession, for practical purposes, a quantitative study has been made of the membership of the A.I.M.E., and is herein reported for the first time. In spite of the effect that a long history and a relatively small group of professional workers have had in limiting specialization in mining engineering, there has nevertheless grown up a wide variety of specialties in this field. More than a hundred different kinds of engineers were discovered among the titles given by Institute members in the Directory, ranging from "advisory engineer" and "American engineer" down to "wire-rope engineer" and "works engineer." How should all these titles be defined and interpreted? How many of them should be relegated as meaningless or confusing? What are the relationships among the remaining useful designations? Should some of them be grouped as "metallurgical" or "chemical," or under some other head?

Jan 1, 1935