Search Documents

By D. M. Doyle

"The Strathcona Concentrator operations, the application of control systems in the crushing, flotation and tailing fill sections, and current and future computer control concepts are described in this paper.The computer has been used for reporting and monitoring roles and operating the on-stream analyzer since start up of the mill in 1968, while over the past twenty months, it has been used for process control. The systems which have been developed include:1. The blending of pentlandite concentrate with pyrrhotite concentrate to produce a special product of constant nickel analysis.2. The blending of cement with tailing fill to produce backfill of consistent cement content.3. The supervisory control of xanthate, frother and pH to the flotation circuits to maintain the nickel copper concentrate grade within narrow limits.IntroductionThe Strathcona Concentrator is currently treating 7,200 tons per day of an ore which contains nickel associated with the minerals pentlandite (28 -32% Ni) and pyrrhotite (0.3 -1.0% Ni). The ratio of the nickel minerals varies from 4 to 15 parts of pyrrhotite to 1 part of pentlandite over the orebody. The production of a high grade concentrate re4uires the separation of this small quantity of .oentlandite from the much greater proportion of pyrrhotite and gangue and is complicated by the presence of two pyrrhotite minerals differing in nickel content, floatability and magnetic susceptibility."

Jan 1, 1974

By José Ricardo Lopes, Alaor Coelho, Marco Gomes, Alfredo Dacio Moraes Filho, Akira Koshima

"Very low strength alluvial peat soil was found under two old drainage galleries with just 4.3m cover above a twin tunnel due to be excavated by a 10.6m diameter EPB Shield for São Paulo Metro’s Line 5. Alignment was required to strengthen soil and drive the TBM through safely without damaging the galleries. The design included six levels of self-drilling forepoling with lengths up to 15m, using 100 mm-diameter SCH160 metal tubing and injection bulbs with estimated 0.20m diameter. Two 6m-diameter circular shafts were excavated along the shield-tunnel axis, one each side of the galleries, and forepoling fanned out under gallery foundations. Given the peculiar soil and confined working space, more data were needed for correct drilling geometry. Ground mass treatment was successfully designed and executed and galleries were fitted with instruments to enable the shield’s advance. DESCRIPTION São Paulo Metro’s Line 5 (aka Lilas or purple line) is adding 11 stations along an 11.5km extension and three EPB TBMs are being used simultaneously (three EPBs on the same job for the first time in Brazil) with one of them excavating a large cross- section twin-track tunnel. Currently the largest work-in-progress for São Paulo Metro, this project has been divided into seven lots and 9km are already operational. This study refers to Lot 6 where the 10.6m - diameter EPB shield excavation is only 4.3m below two galleries running through a 10m layer of very soft peat soil in an old alluvial riverside region ringed by major roads. After recent filling, this area (Parque das Bicicletas) was used for recreation, although temporarily it has become a construction site. This paper will describe the original basic design; precautions in relation to the structural condition of the galleries after inspection; the problem of absence of data for their foundations; subsoil bore tests; evolution of the engineering design for the galleries and conditioning and reinforcing the soft soil below the galleries to ensure safe advance of the EPB shield, and finally the successful outcome of the solution used."

Jan 1, 2016

By A. T. Yu

Over the last 80 years the conveyor belt has advanced from the troughed rubber belt to those with standard steel cable cores and those which can navigate curves or climb steep inclines. Now the latest generation of belt conveyors can claim hitherto unheard of capacities of 20,000 tph and single flight lengths well exceeding 16,000 feet. The stranded steel cable core belt is principally responsible for the spectacular improvement in load carrying ability of belt conveyors. The allowable working tension of these belts ranges from 2,500 lb per in. of belt width for 1/4 in. diam cable to 4,000 lb per in, for 3/8 in. diam cable. These ratings far exceed the 240 lb per in. per ply for rayon or nylon construction, and 30 lb per in. per ply for a lowcost cotton fabric.

Jan 1, 1970

By N. Brown, M. Herman

IT has been pointed out by Cottrell' and Fisher that long-range order would produce superdis-locations, consisting of two partial dislocations separated by an out-of-phase region. The mutual repulsion of the partial dislocations is balanced by the surface tension of the out-of-phase domain boundary joining the dislocations (Fig. 1). The calculation of the equilibrium spacing of the dislocations has yet to be made. The argument uses the Bragg and Williams theory of long-range order." The metal under consideration is the A-B, body-centered type, such as ß brass. The slip system is taken to be [Ill], (110). Since nearest-neighbor interactions are considered, only the atoms position in the two (110) planes adjoining the slip plane have to be labeled. Corner sites are called a and a' in the top and bottom (110) planes, respectively. Similarly ß and ß are the body-centered sites. Thus, a and ß and 0 and a sites are nearest neighbors. Assume that the bottom plane moves and the top plane is fixed during slip; the atoms in a and ß sites exchange sites but atoms in a and ß sites remain fixed. Fraction of A atoms in a sites, for example, is given by fa and fa. for the un-slipped and slipped condition, respectively. Similarly number of A atoms in the a sites is given by n, and n'a for the unslipped and slipped condition, respectively. As the dislocation moves into the ordered region the change in number of A-A bonds is given by

Jan 1, 1957

By Fumito Tanaka

The Mitsubishi Process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates. Continuous converting originates from the application of the proven technology of a lime-ferrite slag (CaO-FeOX-Cu2O) on the Converting Furnace (C-furnace). Recent improvements on the C-furnace operation have included increasing the processing of recycled materials and the investigation of alternative fluxing agents. However, some minor oxides adversely affect C-furnace operation, with respect to magnetite behavior of the slag, with the most significant impact having been observed with the silica content of the slag. This paper will quantify the impact of silica on the lime-based slag, and discusses the controls that have been identified to sustain continuous converting operation.

Jan 1, 2005

By Y. X. Li, L. R. Xiao, S. Gong, S. S. He

Porous copper and porous copper based alloys with controllable pore structure have been manufactured successfully by sintering evaporation process. This process consisted of mixing copper or copper based alloys with NaCl powders, hot pressing and final high-temperature sintering to evaporate the filler material of NaCl powders. NaCl was eliminated completely during vacuum sintering, and strong metallurgical bonding in the walls was achieved. The pores’ structural parameter (pore size, shape, and direction) and porosity can be controlled effectively. These porous copper and porous copper based alloys with controllable pore structure have great potential in many fields. Including heat dissipating materials, heat absorbing materials, chemical catalyst carriers, electromagnetic shielding materials, filtering materials, damping materials, silencing materials, battery electrode materials. INTRODUCTION The development of porous materials began in the 1960s. The research of activated carbon with high specific surface area made porous materials enter the stage of material research (Belyakov et al., 2008; Ferey et al., 2008). With the rapid development of science and technology, porous materials play an important role in material research, and gradually become an indispensable part of the material research field (Wu et al., 2012). The research of porous materials has gradually extended to metal, ceramics, plastics and glass and other fields. It has been successfully applied in many fields, such as functional materials, industrial production, aviation, medical materials, biochemistry and electronics, which fully shows that porous materials have considerable development prospects. Porous silicon, plastic porous materials and glass porous materials are the most widely used in the field of non-metallic porous materials (Capelle et al., 2012). Compared with non-metallic porous materials, metal porous materials have developed rapidly in the late 1980s and become new materials with good mechanical properties and excellent physical properties. Porous metal materials have many advantages, such as large specific surface, small specific gravity, good silencing effect, high stiffness, high electromagnetic shielding performance, good shock absorption performance, etc (Li et al., 1999; Ferey et al., 2008). Among its many applications, metal porous materials can be used as both functional materials and structural materials. In some cases, metal porous materials have dual functions and structures. It is a multi-purpose engineering material with excellent performance. At present, porous copper, porous aluminium and porous nickel are the most concerned materials (Chen et al., 2002; Yang et al., 2017; Liu et al., 2018). The preparation methods of porous copper and copper-based alloys mainly include self-propagating high temperature synthesis (SHS), capsule-free hot isostatic pressing (CF-HIP), spark plasma sintering (SPS) (Kvanin et al., 2008; Takahashi et al., 2008; Zhang et al., 2014). However, these methods can not accurately control pore structure parameters (including pore size, shape, orientation, distribution, etc.). In porous materials, pore structure plays an important role in the overall performance of materials. In order to control pore structure parameters accurately and optimize material performance, it is necessary to explore and develop new preparation technology. In this paper, the sintering evaporation process (SEP) was introduced for the preparation of porous copper and copper-based alloys. The core process of the preparation method is hot pressing and evaporative desalination. Hot pressing can make the pore orientation consistent. Evaporative desalination can ensure the complete removal of NaCl in the form of vapor in a short time, thus eliminating the corrosion of residual NaCl on the matrix metal (Gong et al., 2011).

Jan 1, 2019

By C. Froger

Since its creation in 1950, the Centre d'Etudes et Recherches des Charbonnages de France at Verneuil-en-Halatte (Oise) has been conducting many investigations concerned with airborne dust measurements, particularly in underground mines. The work has resulted in the development, a few years ago, of a new process of dust sampling, whereby the airborne dust particles are collected by a rotary filter of polyurethane foam rotating at high speed within 8 housing.

Jan 1, 1973

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. K. Work

THE Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of steelmaking are partly economic and partly metallurgical.' In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect-it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Bessemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (I) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. THE CONTROL PROBLEM In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By Zhansen P

This paper describes the test re- sults which give a complete proccess of failure of concrete lining embedded in sand medium under load, including the order of appearance of crack along the lining up to failure. nor each crack appearance corresponding calculation being made to assess the redistribution of moment and thrust force in critical section including crown section, section making 45¦ with the vertical etc. De- flection at the above stated critical sections are also measured at each stage of loading. The pressure along the top hori- zontal surface of embedded lining and the vertical sides are measured by pres -sure gauges embedded in sand medium. fhe test results show a complete figure of rupture characteristics of concrete lining embedded in soft ground which approximates alluvial deposite often occur in metro construction at cities near the river side. These test results have been taken as a reference in assessing the action behavior of concrete lining in certain cities in China.

Jan 1, 1987

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

Mining at Waihi on the Martha Hill commenced in 1878 and between 1892 and 1953 produced 35 million ounces of bullion from some 13.5 million short tons of ore from 40 named quartz reefs. The general geology of the ore is recorded in detail with differing interpretations by Bell and Fraser (1912) and Morgan (1924). The reefs and stringers have formed by fissure filling and replacement in mainly quartz andesite dacite flows within the Waihi 'Graben'. The host rocks are extensively propylitised with intense alteration forming zones of kaolin adjacent to the main reefs.

Jan 1, 1979

PRESIDENT LITTLEJOHN: We have with us a gentleman from Utah, who is familiarly known -as the "Mudite King," Mr. Reid, of the Lion Coal Company. Here is a letter I would like to read, and probably Mr. Reid will give us an idea of his Mudite machine, or the results he is obtaining. This question was brought up in Rock Springs, Wyoming, but Mr. Reid was not there personally during the discussion, but Mr. Burnell, who is general superintendent of the Lion Coal Com¬pany, as much as he possibly could, described the system and its effects. I believe Mr. Reid will probably be able to give a somewhat clearer statement this afternoon. This letter is from the Coal Mining Inspector of the State of Utah, John Crawford. "February 10, 1925. "The Industrial Commission of Utah, Building. "Statement of John Crawford, Coal Mine Inspector, in regard to Muditing in Coal Mines: "That Muditing used in connection with our present sprinkling system in coal mines is the missing link to the system we have had heretofore, because the water applied by the former system began to dry out, in heavy air currents, the moment it was put on. Consequently the dust that had been humidified by sprinkling, came back to its natural condition, and if anything, the combustible parts of it, in my opinion, were more intensified than previous to being wetted down. "The advantages that Muditing has over the old system of sprinkling are: "1st. The dust that is on the roof, timbers and sides of the entry is washed completely off and rolled up in the Mudite solution which entirely destroys the wings, crudely speaking, of the fine coal dust. "2nd. Sprinkling with the Mudite system, the water and mud is of greater extent than could be applied with a hand hose by a sprinkler. This sprinkling can be done while the mine is in operation, just the same as if water alone was being used. "3rd. The Mudite solution, when dried out, leaves a coating which serves as an armour to the coal, so that in the event of a local explosion, the inflammable matter on the coal is non-combustible; whereas, if that same coal had been sprinkled with water only, and made free of dust, the heat would have the same effect on the coal as it has on a stove when coal is thrown into it-instantaneous combustion. "Therefore, it is my opinion that the Mudite system is the missing link to the perfecting of our sprinkling system here in Utah. "(Signed) JOHN CRAWFORD." Mr. Reid has with him a few sam¬ples of his Mudite, after it has become solidified, taken from the floor, as I understand it. It is interesting. We have a few minutes to spare to good advantage, were we to ask Mr. Reid to give us an idea of his machine, as briefly as he possibly can, and also what he thinks the effect of the Mudite is compared to dry rock dust. Mr. Reid. (Applause.) MR. W. J. REID (Lion Coal Company) : I came down here with no intention of making any talk on Mudite. However, there being so many people that have seen Mudite at Wattis

Jan 1, 1925

By Edgar E. Vidal, Keith Smith, James A. Yurko

Beryllium, like many other reactive metals, is extracted from a halide (generally BeF2) using magnesiothermic reduction, also known as the Kroll process. The beryllium is produced in a molten state, which when solidified resemble "pebbles". Although beryllium is used in limited quantities compared to other metals (< 100 Mt/annual), it is a critical material for the nuclear, defense/aerospace, and large science markets because of its unique nuclear and mechanical properties. Beryllium processing has unique environmental, health, and safety concerns which must be handled appropriately in the 21st century from a worker and environmental safety perspective, and must be designed with this first in mind. In 2011, Materion began operations of its new Kroll plant – informally known as the “Pebbles Plant” - in Elmore, Ohio. The plant was majority funded by a U.S. Department of Defense Production Act (DPA) Title III grant, which is a unique government/industry partnership program to, "create assured, affordable, and commercially viable production capabilities and capacities for items essential for national defense." After a twelve year hiatus from primary beryllium production, Materion has reentered its extraction business and has relearned how to make pebbles. The purpose of this presentation is to give an overview on beryllium extraction and discuss some of the unique aspects of building and operating a safe beryllium facility during the production scale-up phase.

Jan 1, 2015

By Richard E. Sabaski

The demand placed on the mining industry in the past 15 years for increased production, coupled with lower grade ore and higher cost capital, has resulted in a noticeable increase in grinding mill sizes. The pressure to increase mill size continues. During the mid sixty&apos;s and early seventy&apos;s, ?larger? conventional ball mills were in the range of 13 - 16-1/2 f t. diameter (4 - 5 m) increasing by the mid 70&apos;s to 18 ft. (5.5 m) diameter. At the same time, autogenous mills expanded from 24 - 32 ft. (7.3 - 9.1 m) to the present 34 and 36 ft. (10.b and 11.0 m) diameters. These size pioneers of 16-1/2, 18, and 36 ft. diameter mills from Allis-Chalmers have been free from structural problems, because they were analyzed, modeled, designed, and field tested to meet the challenge.

Jan 1, 1981

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

ROBERT M. KEENEY,* Portsmouth, Ohio (written discussion?).- Mr. Coffin has written a most interesting paper that covers most of the uses to which water-cooled devices are subjected; but to meet with the operating department&apos;s approval, these devices must effect a saving in cost per ton of ingots produced in the furnace. The making of steel in the open-hearth furnace is dependent entirely on the personal element. It is not possible to charge the furnace with so much raw material, turn on a valve for heat, and by use of recording thermometers, clocks, etc. empty the furnace when a steel is made. Competent men trained to the work must be in charge all the time, and the quality and quantity of steel produced is quite as dependent on the care and working qualities of the furnaces as on the raw material and working of the charge itself. Steel making is hot, hard work and the inducement offered to technical men to take up this work is not sufficient to induce many to enter the field. The result is that most of the workmen in an open-hearth plant, the men who actually operate the furnace and make the steel, are not technical men and do not understand the "whys" and "wherefores " and care less. All this means that a furnace must be built as nearly fool-proof as possible. By this I mean that it is necessary to protect those parts of a furnace most subject to abuse by water-cooled devices whenever possible, and these water-cooled appliances must he as nearly fool-proof as they can be made. The control of the gas entering a furnace is of the utmost importance. This means a properly designed port must have the same design throughout the whole run of the furnace. This is not possible with the ordinary

Jan 6, 1919

By T. Watanabe, S. Karashima, H. Oikawa

Creep tests of a! iron and its solid-solution Fe-Mo, Fe-Co, and Fe-Si alloys with bcc structure were conducted under constant stresses in ferromagnetic and paramagnetic temperature regions above 0.5T,(T, is the absolute melting temperature). It was found their high-temperature creep behavior changed in the vicinity of the magnetic transformation temperature, that is Curie temperature, TC. In the ferromagnetic region below the steady-state creep rates were lower than those expected from the extrapolation of the data in the paramagnetic region, the amount of decrease being affected by solute addition. Also, activation energies for steady-state creep were different in the two temperature regions. The observed changes were concluded to be due to the effect of ferromagnetism on diffusion. It is well-known that plastic deformation of metals and alloys in the temperature region where mobility of atoms becomes high enough is controlled by atomic diffusion." Many experimental results394 on fcc and hcp materials have been reported to confirm this view. In bcc metals and alloys, not much basic investigation of creep deformation has been performed. In particular, experimental work on iron5-&apos; and its alloys, covering a quite wide temperature range is extremely scarce. On the other hand, the effect of ferromagnetism on diffusion has recently been demonstrated in a iron and its alloys;&apos; it has been made clear that diffusion rates in ferromagnetic temperatur~e region are significantly lower than those expected from diffusion measurement in the paramagnetic region. Therefore, it is concluded that the magnetic effect influences the high-temperature creep behavior in a! iron and in its alloys. The present authors have conducted creep experiments on a iron and its solid-solution alloys over a very wide temperature range, and have demonstrated the magnetic effect. A part of the result has already been reported elsewhere.26 In this paper, the experimental results will be described in detail. While the manuscript was in preparation, a similar magnetic effect on creep deformation of a iron was reported by Ishida . Though their experiments covered an extremely wide temperature range, the creep stresses varied from several thousand psi to several ten thousand psi with decreasing temperature. Consequently, it may be said that there remain some questions concerning their results. I) EXPERIMENTAL PROCEDURE The materials used in the experiments were pure iron and its alloys; they were prepared by vacuum melting (10"" mm Hg) electrolytic iron (99.9 pct), molybdenum powder (99.9 pct), ultrapure silicon, and cobalt pellet (99.5 pct) in alumina crucibles. The ingots were hot-forged to plates 10 mm thick and 50 mm wide, and then were hot-rolled at about 700°C into sheets 1 mm thick. Creep specimens, 5 mm in width and 15 mm in gage length, were machined from the sheets. They were annealed at temperatures which were well above their respective recrystallization temperatures. The chemical compositions of the metal and alloys are shown in Table I together with their heat treatments. High-temperature creep tests by the use of a lever-type creep testing machine were carried out in argon atmosphere under constant tensile stress. In order to keep &eep stress constant within about *0.5 pct, stress change due to specimen elongation was compensated by tensile force of a stainless-steel bellows which was inserted between the loading lever and lower specimen grip with the assumptions of a linear relationship between change in cross section and strain and uniform strain along the section. Beyond the limit of compensation by the bellows, small amounts of load were removed after appropriate strains. The testing temperatures were maintained to within i2"C of the reported values. Creep deformation was auto-graphically recorded at the upper (moving) specimen grip using a linear differential transformer which was held by a stainless-steel rod mechanically connected to the lower specimen grip. It was also directly measured with a dial-gage reading to -& mm. 11) EXPERIMENTAL RESULTS AND DISCUSSION 1) Creep Curves of a Iron and Its Alloys. Creep curves of a! iron, Fe-Si, Fe-Co, and Fe-Mo (<2 at. pct Mo) alloys usually consisted of three stages, that is transient (primary), steady-state (secondary), and accelerating (tertiary) stages. An example is illustrated in Fig. 1 for a! iron. However, in Fe-Mo alloys with more than 2 at. pct Mo, an inverse transient creepZ8 was observed as indicated in Fig. 2. The inverse behavior, which varied with the amount of molybdenum, may be due to the substructure* in the annealed specimen as was sug-

Jan 1, 1969

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport&apos;s Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1&apos;8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987