Search Documents

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By Oscar Pastor Paredes

Dado que la presión de aire comprimido en los frentes de trabajo (PACFT) es deficiente, se ha visto por conveniente evaluar qué tipo de PACFT es el más adecuado para el rendimiento de máquinas neumáticas. En este sentido, el presente trabajo describe el método de cálculo como el medio idóneo para solucionar las deficiencias detectadas en la compañía minera Condestable S.A y así visualizar el procedimiento a través de un microcomputador Casio PB 700 de lenguaje Basic.

Nov 24, 1986

By M. K. McCarter

A unique telemetry system was developed to monitor potentially unstable natural slopes above a residential area. Continuous interpretation of data transmitted from remote movement-sensitive devices and immediate communication of signficant changes to emergency personnel were made possible by a readily available "home" computer. Even though the computer based system was originally developed for a non- mining application, it could be used with little or no modification to monitor ground control instrumentation in open pit and underground situations.

Jan 1, 1985

By B. McFadzean, M. Becker, S Geldenhuys, A. Molifie

Mineral hydration is known to result in low flotation recoveries and grades within primary platinum group element ores worldwide. This is because the phyllosilicate minerals derived from hydration reactions of silicate minerals (i) form electrostatic coatings on valuable minerals that in turn hinder collector adsorption, (ii) alter the viscosity of the slurry leading to poor gas dispersion and (iii) decrease the concentrate grade due to naturally-floating gangue. Sodium silicate was investigated because its dispersant, rheology modifying, and depressant properties could prove promising in combating the problems associated with these ore types. Quantitative evaluation by scanning electron microscopy analysis revealed large quantities of serpentine and talc present within the ore sample used in this study, which led to a poor flotation response as indicated by batch flotation tests. Using sodium silicate improved the recoveries and grades at high dosages (>1000 g/t). The zeta potential experiments indicate that improved recoveries are, in part, as a result of the reversal of serpentine surface charge, creating electrostatic repulsion between serpentine and valuable minerals which prevents the coating of valuable minerals by serpentine slimes. Ore dilution and rheology tests indicated that decreased viscosity at high dosages also improved recoveries. Talc micro-flotation tests revealed that the depression of talc occurred at higher sodium silicate dosages, which improved concentrate grade. The processing of nearsurface altered ores is becoming an increasing problem worldwide and the use of sodium silicate proved valuable in mitigating the problems associated with the altered ore investigated in this study. Keywords: Alteration, phyllosilicate slimes, colloidal chemistry

Jan 1, 2020

By Mary Jean Buchanan

The last twenty years have seen the advent of environmental concerns and sustainable development, and the industry has witnessed the rise of Environmental Management Systems and their registration through several international standardization systems such as EMAS and ISO 14001. Beyond EMS and ISO 14001, which new goal the mining industry should aim at. Life-cycle assessment (LCA), another tool from the Environmental Management System series, is also on the rise and currently the object of an international standard (ISO 14040:1997). Through LCA, it is possible to assess the environmental aspects and potential impacts associated with products and services, taking into account all the activities required for its fabrication, its use, its transportation and its disposal. How could LCA be applied to the mining industry ? Is the international market pressurizing on mining companies to supply an ?environmental ore?? What about the automobile industry and its use of LCA ? Will it influence the ferrous and non-ferrous metal industry, suppliers of raw materials ? This paper presents a review of possible applications of LCA for the mining industry as well as world trends.

May 1, 2001

By Lewis M. Haupt

IT has given me great pleasure to read, in the papers recently published by this Society, the discussions on the subject of Technical Education, which were developed at the joint meeting held at the Franklin Institute in June, 1876; and since it was impossible for me to be present, I desire to improve this my first opportunity of adding the weight of my testimony and experience to what has been so ably presented by others. It is a subject about which the people need to be kept agitated, that their views may expand with the demands made for a higher and more thorough education. It is the public at large, the capitalist, the manufacturer, and the laborer, who are to be benefited more or less by this elevation of the standard of our professional schools, and it is but just, therefore, that the schools should look to them for the means with which to accomplish so desirable an object. It is no doubt to the interest of a metallurgist to employ a skilled laborer who will prevent waste by properly proportioning his materials ; by regulating the supplies of air and fuel ; by arranging his plant in the most economical manner, and by disposing of his products to the greatest advantage. The engineer is benefited by selecting for an assistant a person able to determine the values of his factors of safety for the same materials in different forms and positions, avoiding expensive suits for damages and cost of reconstruction; he should be able to so locate a road as best to fulfil the requirements of a through traffic, and yet develop local industries. But I need not multiply instances to show what all will readily concede, viz.: the advantages of a theoretical education ; that was fully demonstrated at the previous special meeting, but it is still an open question whether the practical instruction should precede, accompany, or follow the theory.

Jan 1, 1877

By H. Masuda

The lijima Zinc Refinery started operation in 1972, and has today an annual capacity of 200, 000+-Zn. The hematite process was employed for the first time and the ideal of waste-free refinery has been pursued for 30 years. In recent years, however, only half of the hematite produced would be sold to the cement industry and hence a reduction of arsenic level has been necessary in order to sell the entire amount produced, The arsenic cementation process with zinc powder, developed through a long time laboratory research was found among some options as the best for the hematite process. The construction work started in 2000 and the facility was put into operation in 200 I. As a result in the same year all hematite were sold to the cement industry. The outline of this project, present operations and technical issue are reported in this paper.

Jan 1, 2003

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1987 was $446.6 million, an increase over that of 1986 and the first increase in 3 years. Alabama was second in the Nation in production of bauxite and ferroalloys; third in bentonite, crushed dolomite, crushed marble, and fire clay; and fourth in masonry cement. Trends and Developments.-Employment in the minerals industry remained relatively low for the second year even though the overall unemployment rate dropped to 7.9% by December. Employment in mining and primary metals dropped about 10% and 2%, respectively.

Jan 1, 1989

By George CW

Western Mining Corporation (W.M.C.)operate a 30 000 tpa nickel refinery at Kwinana, W.A. using the Sherritt Gordon Process. Following ammonia/air leaching of sulphideminerals and subsequent copper removal, nickel metal is produced as powder by hydrogen red-uction of the ammonium sulphate-rich solution. Batchwise reduction in pressure autoclaves is preceded by an oxidation/hydrolysis step to ensure nickel powder quality.The reduction process is energy intensive, requiring high temperatures and pressures. Present energy requirement is 24 GJ per tonne of nickel reduced. Of this, 95% represents steam and hydrogen consumption and 5% electric power. The design and operation of the red-uction circuit is reviewed, outlining the main areas of steam and hydrogen usage.

Jan 1, 1985

By Brahm Prakash, R. Schuhmann

Maurice Rey—It may be interesting to note that depressing effects can also be obtained from cyclic compounds other than dyes. One such compound which is a dispersing agent for carbon, pigments and other compounds is known in France by the trade name "dispergine" and in the United States by the name of Lomar P W (Jacques Wolf & Co.) Dr. Rey admits that the compound is not very selective and is similar in its action to starch and dextrin.

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Maurice Rey—It may be interesting to note that depressing effects can also be obtained from cyclic compounds other than dyes. One such compound which is a dispersing agent for carbon, pigments and other compounds is known in France by the trade name "dispergine" and in the United States by the name of Lomar P W (Jacques Wolf & Co.) Dr. Rey admits that the compound is not very selective and is similar in its action to starch and dextrin.

Jan 1, 1951

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

By Yotamu Hara, Animesh Jha

"High Curie temperature and large magnetic anisotropy make cobalt an important magnetic material for power engineering applications of magnets operating above ambient. It is also an essential constituent of modem lithium - cobalt oxide batteries, without which modem electronic gadgets will be functionless. Both these applications of cobalt save energy and reduce C02 emission. Ironically, however the production of cobalt from copper and nickel smelting in the world remains one of the least energy efficient process. The paper analyzes the energy balance, material and process chemistry of overall cobalt recovery and the waste generated, which entail the process limitations. We discuss a novel approach for the reduction of sulphide minerals with CaS04, permitting better separation of metals from slag and generating higher concentrations of S02. Such an approach may seem to be an alternative energy efficient option for processing and further purification of cobalt in metallic form. The results are discussed in the context of process thermodynamics and reaction kinetics for Coalloy production.IntroductionCopper sulphides bearing minerals are predominantly associated with iron and cobalt sulphides minerals. Carrollite (CuC02S4) is a mineral that has both copper and cobalt sulphides [1,2], which may also contain FeS, by substituting either Cu2+ or Co2+ ions in mineral lattice. On smelting copper - cobalt - iron sulphide concentrates, some parts of the cobalt often partition to matte at preferentially low oxygen potential by forming eventually an alloy phase with copper, however a significant fraction is often lost into an oxide slag rich in iron and silica. The slag heaps accumulated in the Copperbelt region in Zambia from last 60 years of mineral processing and metal extraction is reported to be 0.3 to 2.6 wt% of cobalt element, which is high [3]. Cobalt is also available in smaller concentrations in the copper smelting and converter slag, as reported in the investigations on the recycling of such slag materials using leaching with ammonium salt [4], iron chloride [5], and sulphuric acid [6], and solvent extraction [7].The recovery of cobalt from slag, irrespective of the techniques researched so far, does not seem energy efficient because the molten slag at 1300°C is quenched by losing thermal and chemical energy. The quenched slag is again reheated to above room temperature for leaching and above liquidus for carbothermic reduction of residual cobalt oxide. For example, in Mintek DC arc smelting [3], 80% of cobalt and 95% nickel are recovered by expending 600 kW per tonne. Assuming that the mineral carrollite is the starting phase, the univariant calculations for the Co-Ca-Si-S-0, Fe-Ca-Si-S-0, and Co-C-Si-S-0 systems are shown in Figure la, lb, and le, respectively at 1573 K."

Jan 1, 2012

By A. W. Gauger

WITHOUT QUESTION the Commonwealth of Pennsylvania contains the most remarkable coal deposits of the whole world. Within its borders ,are to be found excellent coals ranging in rank from the high volatile bituminous of the western part of 'the state through the low volatile or semi-bituminous of central Pennsylvania to that aristocrat of solid fuels, anthracite, found in the East. . . . But while other states and even the Federa1 Government have recognized the needs of the coal industry, Pennsylvania has not. Though bituminous coal represents one of the most important industries in the state, far more important in annual productive wealth than agriculture, for example, hundreds, of thousands of dollars have been spent on agricultural research whereas little or nothing has been spent on coal investigation.

Jan 1, 1932

By Lewis M. Haupt

IT has given me great pleasure to read, in the papers recently pub lished by this Society, the discussions on the subject of Technical Education, which were developed at the joint meeting held at the Franklin Institute in June, 1876; and since it was impossible for me to be present, I desire to improve this my first opportunity of adding the weight of my testimony and experience to what has been so ably presented by others. It is a subject about which the people need to be kept agitated, that their views may expand with the demands made for a higher and more thorough education. It is the public at large, the capitalist, the manufacturer, and the laborer, who are to be benefited more or less by this elevation of the standard of our professional schools, and it is but just, therefore, that the schools should look to them for the means with which to accomplish so de sirable an object. It is no doubt to the interest of a metallurgist to employ a skilled laborer who will prevent waste by properly proportioning his ma terials ; by regulating the supplies of air and fuel; by arranging his plant in the most economical manner, arid by disposing of his products to the greatest advantage. The engineer is benefited by selecting for an assistant a person able to determine the values of his factors of safety for the same materials in different forms and positions, avoiding expensive suits for damages and cost of reconsiruction; he should be able to so locate a road as best to fulfil the requirements of a through traffic, arid yet develop local industries. But I need not multiply instances to show what all will readily concede, viz.: the advantages of a theoretical education ; that was fully demonstrated at the previous special meeting, but it is still an open question whether the practical instruction should precede, accompany, or follow the theory.

By Prodyot Kumar Ray, Sudip Kumar Koley, Aminul Islam, Somnath Banerjee

One of the most important topics in the construction industry is the building of railway embankments. Being such a delicate and significant structure, it is crucial to properly design the embankment and build it while adhering to all statutory criteria and design guidelines. A railway embankment's subsoil condition and fill material, groundwater table, dynamic and static loads during operation, and embankment geometry are some of its most crucial design considerations. This paper discusses the likely causes of the collapse of a railway embankment in eastern India as well as the suggested rehabilitation scheme. It was observed that an embankment collapsed in the aforementioned area during a inccesent rain. Along with the side shifting of a cantilever retaining wall that was positioned at the bottom of the embankment, the embankment next to the railroad track settled vertically. According to the available geotechnical report, the sub soil strata in half of the area adjacent to the embankment profile, where the embankment height gradually decreases from maximum height, is stiff to hard clay with an undrained cohesion value of around 50 kpa followed by dense sand, and the sub soil strata in the other half is soft clay with an undrained strength of 15 kpa. As a result, in the rainy season due to the sudden increase in the water table, the self-weight of the embankment increased and further caused the under-laying soft clay to get squeezed away and settle. Due to this squeeze/settlement effect of the soft clay layer, the retaining wall got disturbed along with the generation of an undulated embankment top profile. As a remedial measure, it is proposed to construct a contiguous bored pile wall at the toe of the embankment to stabilize the slope, and additionally, compaction grouting is recommended beneath the embankment to improve the soft clay. In order to carry out the analysis, certain commercial geotechnical software like Slide, Wallap, and Plaxis 2D are used. The factor of safety of the embankment slope considering the above restoration scheme is adequate under static and seismic conditions.

Sep 1, 2022

By Jorge Injoque Espinoza

El presente trabajo describe la mineralogía de la plata, cobalto, níquel y oro en los principales depósitos de cobre y hierro de la faja costera. Para la descripción de los depósitos se revisan los trabajos de Injoque, así como en diversos estudios de mineragrafía, microsonda y geoquímica.

Nov 1, 1985

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

J. A. MATHEWS, * Syracuse, N. Y. (written discussion?).-The reagent described by Mr. Archer seems to be a selective reagent, useful in one particular field. Nevertheless, the field is one in which it is likely to prove of considerable value, because there is a great deal of alloy steel FIG. 1.-ETCHED 1 HR. IN ARCHER'S FIG. 2.-ETCHED 1 HR. IN ARCHER'S REAGENT. PLOD 60. X 188. REAGENT. IZOD 10. X 188. heat-treated to approximately the properties mentioned in the paper. If it is found, by further tests, to be applicable to a wider range of compositions than merely chrome-nickel steels, for the most part discussed by Mr. Archer, its value will be thereby increased to just the extent to which it can be applied. In view of the fact that certain of these chrome-nickel steels, very similar in physical properties and hardness, show very different results in the Izod or notch test, and in view of the fact that when such differences are noted in the fracture the brittle steels usually

Jan 5, 1919

By Gino Merello

Dado que los cargadores frontales LHD son los equipos encargados de extraer gran parte de la producción en la mina subterránea El Teniente, se justifica el estudio de confiabilidad, mantenibilidad y disponibilidad que permita optimizar la actual estrategía de mantenimiento. En ese sentido, el presente texto señala la optimización de la estrategia de mantenimiento a través de la metodología de revisar continuamente los parámetros básicos del motor diesel y la condición físico-química del lubricante de motor. También se monitoreó con una frecuencia de dos días el estado general de los equipos, con el fin de detectar prematuramente algún tipo de daño que se derive de la implementación de la nueva estrategia.

Jun 1, 2014