Search Documents

By M. B. Bever, A. K. Jena

In the investigation reported here, calorimetric measurements have been made to determine the heat of formation of the compound AuSb2 and the partial gram-atomic enthalpies of antimony and gold in dilute solution in liquid tin and their enthalpy interaction coefficients. In order to interpret the behavior of antimony and gold in dilute solution in tin, nonzero values are assigned to the energies of bonds between like solute atoms relative to the pure solute state. Sa.mples of the compound AuSb2 were prepared by melting stoichiometric amounts of antimony and gold (99.999 pct pure) in evacuated and sealed Vycor tubes, which were shaken vigorously and quenched in water. The ingots were annealed in evacuated and sealed tubes at approximately 700°K for 2 weeks. Metallo-graphic and X-ray examinations gave no indication of second phases or microsegregation. The samples were added from 273°K to tin-rich solutions in a solution calorimeter1 maintained at 623°K. The calorimeter was calibrated with tin; the heat content of tin, H623°K- H273°K, was taken as 4.08 kcal per g-atom.2 In each calorimetric run at least four additions were made. The total concentration of solutes in the bath at the end of any run did not exceed 1 at. pct. The measured heat effect of an addition was plotted against the average of the atom fractions x of Sb + Au in solution before and after that addition. From this plot the heat effect at infinite dilution h,,, and the composition dependence of the heat effect dh/dx in the composition range 0 < x < 0.01 were obtained. The results for the additions of antimony, mixtures of antimony and gold, and the compound AuSb2 are listed in Table I. The heat effect h on addition of a sample of the compound AuSb2 or a mechanical mixture of antimony and gold at 273°K to a tin-rich solution at 623°K can be expressed as:

Jan 1, 1969

By D. Arku

The increased use of sensors to facilitate automation has led to an explosion of data. As data sets grow in size, their use becomes more complex. Therefore, there is an incentive for reducing the size of the datasets, as long as this does not compromise information gleaning. With this in mind, this project explored basic aggregation as a viable alternative to amassing large amounts of data. The goal of the project was to determine if one would arrive at different conclusions had they analyzed aggregated data instead of raw data. In a mine, operational data is typically used for tracking process statistics, correlation between factors, autocorrelation and multivariate models (for a factor of choice). Therefore, this project compared results from such analyses when it was conducted with aggregated data (AD) with the results of analyses conducted with raw data (RD). The data consisted of one-minute-apart readings from a semiautogenous grinding (SAG) mill on the horsepower, feed rate (tons per hour), rotations per minute (rpm), noise, recycle (tons per hour), density (% solids) and bearing pressure (psig). This data was aggregated by averaging five and 10 continuous (one-minute) observations. Changes in statistical measures between the two approaches were typically within 5% of each other. Differences in correlation coefficients between RD and AD(s) were also within this range. Autocorrelations present within RD were preserved in AD, as long as the time lags were scaled for the amount of aggregation. Regression and neural network models were also developed for power consumption. The prediction performance of developed models was similar whether one used raw data or aggregated data. Overall, it appeared that aggregating the data based on 5- or 10-minute time spans would not have resulted in conclusions (from simple or complex analyses) being different from using raw data. In other words, whether one had used raw data or aggregated data, the conclusions would have been the same, suggesting that time domain aggregation, a common industry practice, is a good alternative to storing high-density data in this case.

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2010

By James E. McNulty

Coal reserve estimates are prepared using a simple equation: the product of area, bed thickness, density and recovery factors. Each of these elements involves a degree of risk based on certain assumptions. Reserve area, thickness and density rely on certain physical data whose accuracy, reliability and sufficiency may be problematical. Estimates of recovery factors for mining and coal preparation are often subjective. Most reserve estimates assume, sometimes incorrectly, that the subject reserves will be completely extracted. The principle that certain coal resources are reserves, if they can be considered economically recoverable at the time of determination, needs to be reexamined in the light of recent market cycles. Reserve estimating requires the exercise of judgments, the validity of which reflect the qualifications, experience and objectivity of the estimator.

Jan 1, 1985

By Dexter Kimball

THE ease and promptness with which the public as a whole becomes accustomed to and takes advantage of the work of the engineer, using the term in a broad sense, is almost startling. Surprise at, and fear of radical innovations in transportation and private service quickly give way to blasé indifference, followed instantly by all manner of criticism that these things are not better constructed and managed. Does the street car stop a few minutes on a switch?-summon the State Commission. Is the Overland Express fifteen minutes late on a three thousand mile run?-Congress is memorialized to make the great railroad companies attend to their business. Does central not respond instantly when we take down the telephone receiver?-anathema!! Do the electric lights go out for a minute or so?-the darkness is illuminated by caustic sarcasm and other kinds of spoken English consigning all engineering and engineers to perdition; everyone apparently forgetting how steep the hills were before the days of street cars, how far away San Francisco was before the days of the locomotive, the telegraph and telephone, and how difficult it must have been to study by the light of a tallow candle.

Jan 9, 1922

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By V. Ciribeni, R. J. Ferretti, C. de Arrieta, E. E. Rossi

The relationship between collector concentration and the solution pH at which flotation occurs is discussed for different minerals. When flotation results are plotted as log of the concentration against pH, the values define areas of total, partial or no flotation. The experiments were performed in three different conditions: a) floating with the same solution used for conditioning; b) floating with water at the same pH as the conditioning solution; and c) floating with water at pH = 7. In each case, the results obtained are quite different. It is suggested that the presence of a second layer of collector reduces flotation over some domains in the graphs. These domains are called depression areas.

Jan 1, 1992

By Richard Akerman

(Translated by FREDERICK PRIME, JR., Professor of Metallurgy in Lafayette College, Easton, Pa.) [THE attention now being paid both in this country and Europe to the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this sub¬ject, is a quite sufficient excuse for presenting this paper to the Amer¬ican Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

Jan 1, 1873

By Tomoya Nihei, Hiroshi Hayashi

"A novel selenium removal process called Recycled Green rust/Ferrite Process is developed by MMC. In this process, a mixed Fe2+-Fe3+ hydroxide compound, green rust (GR), reduces selenate to elemental selenium, while GR is consequently oxidized to magnetite Fe3O4. Sequencing batch-mode experiment showed that the residual selenium concentration gradually decreased with the number of batch test increased. Stable selenium removal was achieved when the number of batch test exceed 15 times. Optimum selenium removal ratio reached 99.95% where initial Se concentration 2.1mg/L decreased to 0.001mg/L. Furthermore, the continuous feeding test carried out through a pilot-scale plant with a feeding capacity 600 L/hr. Approximately 860-hour-feeding test was carried out for the selenium-contaminated groundwater which had an averaged selenium concentration of 0.88 mg/L. Selenium concentration in the effluent from thickener maintained less than 0.01 mg/L (selenium removal rate of 99%) until a net operating time reached 800 hours.IntroductionJapan is one of the largest producers of selenium, and thus there are potential environmental impacts of selenium on soil and aquatic environments. The Mitsubishi Material Corporation (MMC) owns some real estate properties whose soil and groundwater was polluted by selenium and other heavy metals. These sites include former industrial plants: a smelter for nonferrous metal and a fabricating semiconductors and pigments. Selenium in aquatic environment commonly exists in four oxidation states, namely, VI, IV, 0 and -II. Selenate ion (SeO4 2-), the most oxidized form of selenium, and selenite ion (SeO3 2-) are highly soluble and mobile. Elemental selenium (Se0) is insoluble in water and therefore has much lower toxicity. Because selenium is carcinogenic and teratogenic at high concentration, the national effluent standard in Japan is fixed at 0.1 mg/L and the environmental standard at 0.01 mg/L. Although there are several selenium removal techniques, the most conventional process is coprecipitation with a ferric hydroxide because of its simplicity and low cost. It is known that selenite is adsorbed strongly on the surface of ferric hydroxide, but selenate is not. The low affinity of selenate on oxide mineral surfaces was demonstrated by the fact that selenate could be easily displaced by adding competing anions, particularly sulfate ion. Selenate removal from polluted water is one of the most difficult techniques, and more effective methods are desired. MMC developed a novel selenium removal process [1]. In this process, the concentrated slurry that contains Fe(II)-Fe(III) hydroxyl-salts known as Green Rusts (GRs) contributes to selenate removal. The main components of the iron precipitate in the reactor are GRs and their oxidation product, magnetite (Fe3O4)."

Jan 1, 2008

By C. H. Cheng, C. E. Birchenall

The fundamental problem in the thermodynamics of solid solutions is the determinatiorl or calculation of the activities of the components as a function of temperature and composition. Since the theory of metals is not suficiently developed to allow a priori calculation of these quantities, they must be obtained from experiment. C. Wagner1 has reviewed the literature of this subject for the period before 1940. Although several important and extensive studies have been made in the meantime, the number of systems to which any sort of quantitative information can be assigned is vanish-ingly small. These data have become of great potential importance in studies of the structure of solid solutions2 and intermetallic compounds, the nature of the diffusion process,3,4 and perhaps even the mechanism of mechanical deformation.5 For these reasons, it. seems very worthwhile to extend the experimental data in this field. Although there is little use in duplicating Wagner&apos;s review, attention should be directed to the most recently reported investigations. A brief enumeration of the methods of measurement previously employed also should be valuable. The most direct method is the determination of the partial pressure of the components in the vapor phase in equilibrium with the solution. Both equilibrium and kinetic methods have been tried in metal systems, but almost exclusively on liquid phases. Only in the ease of carbon in iron alloys and in the copper-zinc system have extensive measure- ments been made which include solid phases. When one of the components is an element, such as nitrogen or carbon, which forms compounds which are very volatile and stable at normal temperatures and pressures (CH4, Co2, CO NH3), it is frequently possible to equilibrate mixtures containing these (such as CH4-H2, CO2-CO, NH3-H2) independently with the elernents (C, X) and with the metal (Fe, Ni, etc.). Such measurernents have been made for carbon in iron, iron-silicon, and iron-manganese alloys by Smith6 and in iron and iron-nickel alloys by Toensing.7 Differences between carbon activity values at the same temperature and carbon content when carboil is introduced from CH4-H2 rnixtures or CO-CO. mixtures indicate that the effects of hydrogen and oxygen in the system are not negligible, and one can only hope that the true value lies somewhere between these sets of results, probably nearer the CH4-H2 data since hydrogen is less soluble in iron than oxygen. This is essentially an equilibrium method, although flowing gas is employed. A kirletic method has been employed which consists of sweeping an inert gas (generally hydrogen) over the alloy at a series of rates, condensing the metal vapor out,, and analyzing it. The metal content can be extrapolated to zero flow rate (equilibrium). Wejnarth&apos;s8 work on Cd-Mg and Zn-Mg is a good example of this frequently used method. A variant of this consists of equilibrating a known volume of inert gas with the alloy, sweeping it out quickly, and analyzing for metal. In common with the above method, it has the disadvantage that the "inert" gas is generally somewhat soluble in the alloy. Moreover, the former continuously displaces the system from equilihrium and may give low values if solid diffusion is involved. The dew point method applied by Hargreaves9 to the alpha and beta brasses and by Schneider and Stolll0 to A1-Zn avoids the introduction of another component to the system, but is useful only in systems in which one component is much more volatile than the other. The alloy sealed in one end of an evacuated silica tube is heated to the desired temperature. The temperature of the other end is lowered until droplets of the volatile component condense. When the temperature is raised slightly, the droplets will evaporate. By careful adjustment of temperature, the range between evaporation and condensation can be narrowed appreciably. An independent determination of the vapor pressure of the . pure volatile component is necessary to give the partial pressure over the alloy. This is the method employed here to determine the vapor pressures of zinc and cadmium over their silver alloys up to 34 pct in cadmium and 76 pct in zinc. The former involves only the a solid solution, but the latter covers the a, ß, y, and e fields. In recent determinations, Herbenar, Siebert, and Duffenbarkl1 used the

Jan 1, 1950

By Jeong-Soo Sohn

Physical treatment and chemical treatment of spent lithium-ion battery were studied in our research team. Especially we developed two types of acidic leaching for crushed powders containing LiCoO2 of spent lithium ion battery. One of them is sulfuric acid leaching with H2O2 as a reducing agent. The leaching rates of cobalt, lithium and the other metals were above 99 % at the condition of 2 M H2SO4, 10 vol. % H2O2, 75 °C, 300 rpm agitation speed, 250 g/5L solid liquid ratio and 75 minutes reaction time. And the other leaching process is the oxalic acid leaching. In this process more than 99% of Li and less than 1% of Co were dissolved at the condition of 3M oxalic acid, 80°C reaction temperature, 300rpm agitation speed, 50g/L initial solid/liquid ratio and 90min extraction time. Each process has its advantage and disadvantage. In sulfuric acid leaching, leaching reagent is very cheap and cobalt could be recovered into cobalt hydroxide. On the other hand, oxalic acid is more expensive than sulfuric acid but lithium could be dissolved selectively. Also cobalt could be recovered into cobalt oxalate and it could be changed into cobalt oxide after heat treatment. In order to select the effective recycling process, recovery rate and purity of cobalt hydroxide and cobalt oxalate were compared and it was investigated which process was more environment-friendly and economical.

Jan 1, 2006

Adhesion of Escherichia coli onto Oxide Minerals - Extended DLVO Theory and Flotation Behaviour

Sep 13, 2010

By Qingcai Liu

The effect of the TiC addition on corrosion resistance of the Al2O3-C refractories in smelting reduction melts has been studied by quasi-station immersion and rotary immersion. The corrosion rate of Al2O3-C refractories is decreased with the TiC addition. The corrosion mechanism of Al2O3-C refractories is oxidization of graphite carbon by the oxides of the melts and the formation of deteriorate layer.

Jan 1, 2006

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

By K. K. Kohli

Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence-induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months&apos; survey, the data collected include 17 longwall panels and 2 room and pillar sections. The data in-each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages.

Jan 1, 1980

By J. T. Sims, C. E. Karayannopoulos

Today&apos;s rare earth industry is undergoing significant and rapid evolutionary change toward greater reliability and diversity of supply, increased security of supply chains, and better price forecasting. Technology innovation is reducing rare earth production costs while decreasing the impact of producers on the environment. Advances in rare earth material science are reducing the need for relatively scarce heavy rare earths (HREEs) in high-performance neodymium-iron-boron (NdFeB) permanent rare earth magnets and opening the NdFeB magnetic market space for a broader range of downstream applications. Rare earth producers such as Molycorp are increasingly able to offer long-term supply agreements with forward price predictability, something that has not been the case for many years. All of these trends are helping to restore the confidence of customers and other stakeholders in the rare earth space. That increased confidence is likely to bolster global demand for rare earth materials and expand innovative utilization of these remarkable materials.

Jan 1, 2014

By J. T. Norton, N. J. Grant, A. M. Gervais

An investigation of the creep deformation of coarse-grained high-purity aluminum at temperatures approaching the melting point permitted the formulation of a theory of subgrain formation. Subgrain boundaries were found to be formed by two different processes: kinking and polygonization. Polygonization is considered as the main factor in subgrain formation. SINCE "slipless flow" was first discussed in detail by Hanson and Wheeler,&apos; many studies have been undertaken to determine how metals deform at high temperatures. Several types of observations have been reported. Jenkins and Mellor,² working on the creep of mild steels and various grades of commercial irons, found metallographic evidence of a kind of substructure within the grains after deformation at high temperatures. Homes" observed after creep deformation of steel at high temperatures that the original X-ray spots were sharply divided into several small ones. The same phenomenon was reported by Hirst4 from his studies on lead and later by Crussard5 from his work on aluminum. The works of these investigators demonstrated beyond any doubt that the splitting of the X-ray spots was due to the fact that the grains underwent a division into subgrains during deformation at high temperatures. Since then, numerous experiments have been undertaken on aluminum in order to determine the mechanism of formation of subgrains. Research workers can be divided, for the purpose of discussion, into two different groups as regards thinking on subgrain formation. On one hand, based on the work on polygonization by Cahn,6 Guinier and Lacombe,7 Greenough and Smith," Crussard,10,11 and Servi, Norton, and Grant," it was concluded that subgrain formation was a consequence of the simultaneous effects, first, of inhomogeneous deformation which produced bending of the lattice, and second, polygonization. On the other hand, Wood and coworkers13-16 based their work on the results of an earlier report" which dealt with crystallite size and a fragmentation theory. It is interesting to note that while Greenough and Smith8 and Wood et al. performed similar experiments, their conclusions were quite different. Wood et al. did not recognize polygonization as a fundamental mechanism and said that aluminum, at the beginning of the deformation, fragmented immedi- ately into subgrains in order to permit deformation of the metal, the number of these subgrains being a function of strain rate and temperature. They concluded that deformation of grains occurred by flow along the subgrain boundaries. In view of the contradictory conclusions, it would appear that the data were not explicit enough to provide an unambiguous conclusion. It appears that the techniques by which most of the results were obtained, namely, X-ray work, were not enough by themselves to solve the problem. Another approach was needed. In the present research, therefore, an extensive metallographic study was planned to supplement the X-ray work. The importance of revealing the subgrain boundaries metallographically was realized, and this will explain the extensive development and use of etching techniques. In order that subgrains would be considerably larger and therefore more readily visible under a microscope, the creep experiments were performed at very high temperatures approaching the melting point of aluminum. Development of Experimental Technique Creep tests were run at constant load on high purity (99.995 pct) aluminum specimens having a very coarse grain size. None of the specimens was run to fracture. The specimens were originally round (diameter, 0.187 in.; gage length, 1 in.) and had parallel flats milled in the gage section to permit

Jan 1, 1954

By Robson Luís da Silva Nascimento

O mercado do aço no mundo está muito competitivo, e as indústrias siderúrgicas têm desenvolvidos projetos com foco na melhoria da qualidade dos aços e na redução dos custos dos processos de fabricação. Este trabalho descreve os avanços nos processos de lingotamento contínuo, com foco na redução do sucatamento de placas por “bolsa”. Esta melhoria consistiu na modificação na taxa de refrigeração aplicada na placa de cauda durante o processo de descarga da máquina (final de lingotamento). A implementação dessa ação propiciou uma homogeneidade na solidificação das placas de cauda aumentando assim sua temperatura de extração reduzindo significativamente o sucatamento das mesmas. Outras melhorias obtidas com o trabalho foram a redução das ocorrências de placa parada no interior da máquina, redução das ocorrências de restrição de velocidade por Baumann, redução das ocorrências de intervenção para regularização de GAP e melhoria na qualidade superficial. O trabalho foi realizado sem investimento contribuindo na redução do custo de transformação do aço em placa.

Jul 30, 2018

By V. W. Skema, M. W. Smith

Pennsylvania has 4,000 km (2,500 miles) of streams that do not meet water-quality standards due to acid mine drainage (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. To abate AMD, Pennsylvania is using a watershed-based approach that includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Water-shed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves that could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 2002

Sluice-boxes are by far the most widely used concentrating devices by small-scale operators in PNG who work alluvial gold deposits. The sluice-box designs and their operating conditions used are known to vary widely. The selection of sluice-box configuration and the operating parameters such as the water flow rate is purely based on past experience. Some use small flowrates to increase the fine gold recovery at the expense of efficient separations and capacity while others use high flow rates resulting in increased fine gold losses but with high throughput rates. Recent work has revealed that the combination of riffle height, their spacing and wash water flow rate are the most important parameters that determine the success or failure of such operations. This combination has been shown to depend on the in situ gold and gangue size distributions of the deposit being processed. This paper describes a design procedure which uses a non-linear optimisation method to determine the optimal combination of the above parameters to maximise the metallurgical efficiency of such operations.

Jan 1, 1993