Search Documents

By Peck W

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

By W. Valderrama, D. G. Almond

Operation of large SAG mills requires a change in the conceptual approach to grinding processes. The traditional energy consumption criteria are now enhanced with new criteria derived from the mechanical dynamics of the mill load. This new approach demands instrumentation capable of providing accurate information about the load movement and the ratio of balls and ore inside the mill. This paper discusses two new performance enhancing tools available to meet these needs.

Jan 1, 2004

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

By J. V. Ghelarducci, M. A. Sharpe, D. G. Chedgy

This article presents a novel design, called the Climax, High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 ~ 660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax, magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Feb 24, 1997

By Khoi Nguyen, Keeney. Luke

An outcome of geometallurgical mapping and modeling is the generation of continuous down hole profiles of quantitative geometallurgical attributes at assay scale. These attributes vary from traditional routine data collection methods such as assays and geotechnical logging (e.g. RQD, Fracture Frequency), to new measurements including petrophysical attributes, EQUOtip hardness data and modelled estimates of metallurgical performance indices (e.g. A*b, BMWi). Highly variable continuous geometallurgical data with high spatial resolution can make it difficult to identify spatially continuous domains. An automated method based on the well known time series analysis technique of cumulative summation (CuSum) has been developed which uses statistical analysis to identify domain boundaries in down hole profiles. A bootstrap analysis automatically identifies potential domain boundary locations with associated confidence levels and a series of t-tests determine the significance of defined populations. A hierarchical clustering algorithm is applied to results to enable data sensitivity to be taken into account. The method produces statistically significant populations and is suitable for application on either single or multiple drill hole datasets. Domains defined preserve the inherent variability of the continuous down hole data and provide a method for scaling up variability data (i.e. assay interval scale) to mine scale (i.e. bench scale, block model). A major advantage of the method is its ability to provide suitable input parameters for use in spatial modeling of non-additive and non-linear geometallurgical attributes through conditional simulation techniques.

Jan 1, 2014

By N. Mangesana

The effect of high solids concentration and coarse particle sizes (d50 ranges 90?300 µm) on the viscosity of a suspension of water and silica sand was investigated. The experiments were designed to include conditions that have been tested by other authors and those encountered in the operation of tumbling mills. The rheological data was measured using a tube rheometer with operating pseudo shear rates of up to 1500 s-1. The rheograms obtained depicted dilatant behaviour. The Otswald-de Waele, Bingham, Herschel-Buckley and Casson models were fitted to the experimental data. The Herschel-Buckely model, which approximates the yield point and gives an indication of the shear thinning or shear thickening behaviour of the suspension, was found to provide the best description of the flow curves for all slurries. The Herschel-Buckely model was then used to determine the apparent viscosity of all the tests. The apparent viscosity and yield stress increased with solids concentration and particle size at the different pseudo shear rates. The increase in slurry viscosity with solids concentration was attributed to increased frequency of particle-particle interactions. The increase in slurry viscosity with particle size was attributed to increased inertial effects. At low shear rates the sand slurry exhibited shear thinning behaviour for all solids concentrations. At higher shear rates above 1000 s-1the high solids concentration suspensions exhibited a transition from shear thinning to a shear thickening behaviour.

Jan 1, 2008

By I Halikia, T Lilis

Lead smelter slags, produced during the last century in quantities ofmillions of tonnes at Lavrion, Greece, have recently been used in theconstruction of Lavrion harbour. In order to evaluate the geochemicalstability of slags and assess their environmental impact on the aquatic environment, a detailed study on lead leachability under conditions that simulate subsea environments was carried out. Leaching experiments using magnesium chloride solutions under mild temperature conditions were conducted and the effect of main parameters on lead solubility was examined. Furthermore, kinetic analysis on the experimental results was performed. Based on the results, lead dissolution increases by increasing the reaction time, magnesium chloride concentration in the bulk solution and temperature, whereas it decreases by increasing the slags particle size. The reaction order was found to be approximately 0.5 at the initial extraction stages and the activation energy value from the Arrhenius plot was estimated to 29.8 KJ/mole. Diagnostic equations applied to all the experimental data reveal that lead dissolution is mainly controlled by diffusion through the ferrosilicate matrix of the slag particles, which is in accordance with the low activation energy value. The JanderÆs diffusion equation [1-(1-a)1/3]2=kt was proposed as the equation representing the reaction of lead dissolution from slags using magnesium chloride solutions.

Jan 1, 1999

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By A. Eccles

Phase designs are the foundation upon which all open pit mine sequence optimizations and budgets should be built. Unfortunately, at times, mine engineers skip the step of developing realistic pit phase designs - designs that include access ramps and mineable widths. Without mineable phase designs, their optimized schedules are based on theoretical pit shells or ?quick-and-dirty? plans with no ramps. The output from such optimizations is almost always overly optimistic. Without mineable designs, the production estimates are misleading, because they overestimate ore, and underestimate waste stripping requirements. Worse yet, when plans are not based on realistic phase designs, they can point to exactly the wrong decision in feasibility studies (i.e. ?go? when it should be ?no-go?). This paper discusses the importance and features of good pit phase design, and demonstrates the pitfalls of relying on optimized production sequences that are not based on properly designed pit phases.

Feb 27, 2013

By Alexander Malahoff

The new ship-submersible system with R/V Ka'imikai-o-Kanaloa as a mothership and the PISCES V as the submersible completed its first season of dives. The dives involved deployment of the PISCES V in the Hawaiian Islands between the months of July and October 1996. Submersible deployments up to depths of 2,000 meters in sea states up to a high three were made. The new hook and clasp deployment and retrieval connection for PISCES V to the telearm was shown to be an effective system for handling the PISCES V with the A-frame. The shipboard multibeam survey and seawater sampling capability proved to be especially effective in re-mapping the summit of the submarine volcano Loihi following a major volcano-tectonic event and for following the source and configuration of the new hydrothermal plume. Following the earthquake swarm of July 17 to August 18,1996, major changes in the geological setting of Loihi submarine volcano took place. Prior to the seismic event, the geology and structure of the summit of Loihi was represented by a platform-like area 8,100 meters long and 5,400 meters wide enclosed by the 1,200-meter depth contour. The summit was characterized by the presence of two prominent pit craters and eastern and western crater located at water depths of 1,100 and 1,370 meters, respectively. A hydrothermally active volcanic cone, named Pele's Vents, was located at a depth of 960 at the southern edge of the summit. The floor of the summit of Loihi was largely covered by prismatic talus, with interstitial hydrothermal clays. Pillow and tube lavas with volcanic cones 5 to 50 meters high were exposed along the axes of the southern and northern rift zones. The inner margin of the summit displayed fissures and normal faults with the downthrown component towards the center of the summit. The pre-earthquake structural data suggest a pre-caldera structural stage for Loihi. Maximum sustained hydrothermal activity observed on Loihi over the past 10 years existed at Pele's Vents with other sporadic venting occurs along the summit platform and along the south rift. Following the earthquake swarm, the hydrothermally saturated Pele's Vents cone gave way and slid into the inner pit crater. Subsequently, the observed above- bottom hydrothermal plume source deepened from 960 to 1,160 meters, possibly emanating from the same intrusive heat source as Pele's Vents. The observed inward collapse of the summit structures and subsequent opening of fissures gave rise to diffuse venting from the newly formed caldera-like depression with the bottom-hugging hydrothermal pool located at depth between 1,250 and 1,220 meters at the sites of the pit craters.

Jan 1, 1996

By S. O?Connor

When one looks back and does assessments of what has been the key ingredient in achieving success in our safety efforts, there are many issues that spring to mind and cover a wide array of elements. One does not know which has the ultimate maximum effect. In his presentation yesterday, Alan Peers, our SHEQ leader, covered a lot of detail with the way we are managing safety at Modikwa. I have attempted to identify some of the key essentials in making the mine safe. Passion Safety is addressed with a passion that is unbelievable at times. When I get phoned because an incident has occurred and in reporting the incident, there are already action plans being put in place to prevent re-occurrences, you understand the commitment to put employees? safety first. You hear the disappointment in your subordinates? voices when they have to share the fact that an incident or accident has occurred.

Jan 1, 2011

The author's written response to previous discussion of his paper published in Trans. Inst. Min. Engrs.,1915, vol. L, p.51, discussion p.431, was presented at the Mining Institute of Scotland's general meeting held in Edinburgh on 12th February 1916 with D.M. Mowat in the chair

Dec 1, 1916

By Steve Kral

The power industry throughout the world is in the midst of a significant transition that will result in a major restructuring. Deregulation of utilities in the United States is continuing, resulting in increased competition among power providers. The traditional ways that electric power is globally bought, sold and delivered will also change. However, according to the Department of Energy's (DOE) Pat Godley, one thing is clear: "Those who provide the power during the 21 st century will be those who are willing to change - those who are willing to accept new ways of doing business and willing to employ new technologies." Godley is assistant secretary of fossil energy with DOE. Her comments came during the opening remarks at the Fourth Annual Clean Coal Technology Conference, held in Denver, CO, Sept. 5-8, 1995. The conference was sponsored by DOE and the Center of Energy and Economic Development. Under the theme "Global Opportunity," more than 300 coal and utility executives spent three days discussing the new face of the electric-power industry throughout the world and the new, mostly clean coal technologies (CCT) that will be available to power providers.

Jan 1, 1995

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994

By CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU, Shunliang Liu

With the depletion of mineral resources and the growing demand for metal resources from industrial development, the recovery of metal resources from secondary resources has attracted increased attention. Among all secondary resources, spent catalyst is one of the most important as it contains valuable metals such as vanadium, nickel, molybdenum, cobalt, and aluminum. Compared with the extraction of metals from minerals, the recovery of valuable metals from spent catalysts has the advantages of a simple process, a short production cycle, lower investment cost, and less environmental impact.

Apr 1, 2023

The paper presents the development of an integrated computer aided design and planning of open cast mining, with the use of object-oriented modelling and geoinformation technologies, on the example of interaction of the subsystems on planning optimisation and freight traffics.

Dec 6, 2010

By Francis Clark

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200° C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating. EXPERIMENTAL WORK The object of the experimental work was to study the effect of mechanical work on rolled 60:40 brass, quenched and reheated, and the mechanism of twinning in the alpha reeds of a furnace-cooled specimen. It was desired to determine the effect of mechanical work on the transformations taking place on reheating the quenched material, both at 200 and at 470° C. A study of the nature of the structure resulting from the breakdown of the beta at 200° C. and a study of the mechanism of twinning above 470° C. were considered problems for investigation. The question of the twinning of the alpha reeds was also an important phase of the work. With high-power magnifications, there was hope of following these processes.

Jan 1, 1927

By Doris M. Hyde

The 350,000-barrel-per-day Bahamas Oil Refining Co remained closed throughout 1986. Financially troubled Charter Oil Co., joint owner of the refinery with Chevron Oil Bahamas Ltd., agreed in principle to have Chevron assume full ownership in return for canceling debts owed Chevron. Finalization of the agreement was pending at yearend. Burmah Oil Ltd. took more than a $30 million loss on the sale of its interest in South Riding Point Grand Bahama Transshipment Terminal to South Riding Point Terminal Holding Ltd.

Jan 1, 1988

INAP was formed in 1998 by a number of major mining companies, with a view to sharing acid rock drainage knowledge and experience, and to coordinate global research on the management of sulfidic mine wastes. INAP is now moving to further strengthen its global role by networking with regional organisations that are active in the area of ARD, including MEND 3/NEDEM 3 in Canada, the ADTI in the USA and ACMER in Australia. The INAP-Regional Organisation partnership will be formally launched at the 6th ICARD.

Jan 1, 2003

By Steven W. Hunt, Safdar A. Gill

Design and construction of temporary shafts for underground facilities often require evaluation of bottom stability due to rupture (blow-ins) caused by water pressure acting on a bottom plug. This paper provides an overview of shaft bottom stability evaluation methods for the case of a relatively watertight soil plug which overlies an artesian aquifer. Methods of considering plug perimeter shear, plug buckling and pressure relief are discussed. Minimum factors of safety are suggested. Future use of the shaft subgrade is also considered. Bottom plug failure case histories at several shafts are evaluated. This paper should be useful to project designers, ground support system design engineers and contractors involved with construction of shafts for underground facilities

Jan 1, 1997