Search Documents

By Sam Tour

Some years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.' The life of dies was considered in relation to. the casting temperature, the material used for the die and the heat to be absorbed by the die per unit volume of casting made. The mechanism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines. Importance of Heat Checking Heat checks in steel are the source of trouble in many industries besides that of die casting. Every shop where metals are subjected to hot working is searching for improvement and hoping for a cure. The development of a material of sufficient strength to be used as a die and yet devoid of the property of heat checking would be a godsend to many shops and many industries. The need for thorough study and research on the subject is evidenced by the wide variety of hot-working die steels on the market. It is peculiar, but true, that in practically every case the maker of the steel can give concrete evidence to prove his contention that his type of hot-working die steel is as good as or better than any other. A number of steel companies have several hot-working die steels from which choice can be made to fit a particular set of requirements. Possibly to expect one material to be universally the best hot-working die steel is unreasonable. In some hot-working operations, as in drop forging, the die must have great toughness to withstand the stresses developed; in other operations, as in hot piercing or punching, resistance to erosion at high temperatures, possibly defined as strength and hardness at elevated temperatures, is required. In still others, as in die casting, only sufficient hardness to resist scoring between moving surfaces is required, whereas the resistance to sudden changes in temperature must be at a maximum.

Jan 1, 1935

By P. E. Sperry, J. M. Duncan

INTRODUCTION The purpose of the report on which this paper is based is (1) to evaluate the potential for cost reduction of urban mass transit tunnels by use of alternative materials transport systems during the tunneling process, and (2) to identify research and development program elements to assure that the materials transport system will not become the limiting factor for the rate of excavation. The approach taken was: Review the state of the art of urban tunneling by extensive interviews with representatives of tunnel contractors, equipment manufacturers, government agencies and consultants, and by review of recent literature.

Jan 1, 1979

By Donald J. Olson

The North 27th St. ISS Extension tunnel will, under present plans, be the last constructed section of Milwaukee Metropolitan Sewerage District?s (MMSD?s) existing deep tunnel system. The 6.5 m (21 ft) finished diameter tunnel is approximately 3,260 m (10,590 ft) long and is located in NE Milwaukee County. When disputes over the pro-cesses to be used in owner-directed pre-excavation grouting in rock threatened the completion date stipulated between MMSD and the State of Wisconsin, the MMSD and J.F. Shea, the contractor, entered into a unique agreement. Shea accepted responsibility for all shaft and tunnel grouting and water control during the project in exchange for settlement of claims related to grout quantities and perceived delays. This significantly reduced risk for the MMSD and helped ensure the stipulated completion of the project.

By Gene F. ] [Faufaul

This contract was concerned with the design, development, fabrication and testing of an improved tamper-proof filter cassette assembly for use in the, collection and evaluation of dust particulates, primarily in mining areas. This report presents the design effort, fabrication and tenting of five- prototypre unit$ as well as the design and production of 1000 filter cassettes with sampling heads. This new improved filter cassette has been tested and approved by NIOSH as meeting the requirements specified in the contract.

Jan 1, 1978

By W. R. Crane

The effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. Drainsge in these mines has been discussed in papers on mining practice,' but the fact that water, varying from 0.16 to 3.46 and averaging 1.43 times the amount of ore mined, has to be pumped from the mines daily, indicates the importance of the problem and the advisability of making a thorough investigation of the source of mine water, its mode of entry into the mines, its effect upon mining conditions, and consideration of means of improving the conditions.

Jan 1, 1927

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

A mathematical model is developed for flotation in a countercur-rent column where continuously generated air bubbles rise through a downward flowing pulp. The model is based on the assumption of axially dispressed plug flow of both the liquid and air-bubble phases. An appropriate flotation-rate expression, which takes into account the changing concentration of solid particles on the bubble surface, is formulated and applied to the column flotation process. Although a complete solution of the resulting equations is not possible for the general case, solutions for specific limiting cases have been obtained. From these, it is possible to predict theoretically the dependence of the column performance on certain variables. Specifically, concentration profiles as a function of height in the column have been calculated for various values of the characteristic dimensionless parameters. The effect of axial dispersion on the perforance of the equipment is pointed out. In recent years, there has been considerable progress in delineating the fundamental physicochemical principles underlying the unit operation of flotation and in advancing methods for kinetic analysis and process modeling of flotation.' In general, nearly all such process research has been concerned with the analysis of conventional flotation equipment and circuits. From these investigations, the possibility of developing and designing flotation apparatus for more efficient separation appears limited with conventional equipment. How- ever, recently there has been an attempt to apply coun-tercurrent flow techniques to flotation in the context of a flotation column.- some of the results from pilot-plant studies2 indicate possibilities for success of this process at least in obtaining higher-grade concentrates though not higher recoveries. A flotation column operates on countercurrent principle in which bubbles continuously generated at the bottom of the column rise through the downward flowing slurry. A schematic diagram of the flotation column is shown in Fig. 1. The physicochemical principles of bubble-mineral attachment, using this flotation column, are essentially the same as those which prevail in conventional equipment, the only differences being in the flow patterns of the various phases. The salient operating feature of the column as compared to those of a conventional cell is that neither mechanical nor turbulent pneumatic agitation is employed. The column is

Jan 1, 1971

By Edward Hart

Having occasion several years since to make ferrous sulphide, I attempted to do so by fusing a mixture of coal-brasses (FeS2) and dried ferrous sulphate. A very nice-looking sulphide was obtained; but on attempting to use it, I found that it was insoluble in dilute hydrochloric and sulphuric acids. The subject was laid aside at the time, but has since been taken up; and some curious results have been obtained, which I believe are new. I have made the material by all of the following methods and the product seems to be pretty much the same, however obtained : (a) FeS2 heated to fusion. (b) FeS2, and FeSO4 heated to fusion. (c) FeS2, and Fe2O3 heated to fusion. (d) FeS2, and FeCO3, heated to fusion. (e) FeSO4, and S heated to fusion. (f) Fe2O3 and S heated to fusion. Obtained in this way the mass after cooling breaks easily and is very nearly black in color. On the upper surface of the fused cake the color is generally reddish or brownish black. When this is treated with dilute sulphuric or hydrochloric acid, it refuses to dissolve; but if touched with the point of a file or any piece of wrought-iron, solution of the sulphide takes place with the evolution of sulphuretted hydrogen. If the iron is removed the evolution of gas ceases, and only begins again when the iron is again brought into contact with the fused sulphide. The same thing happens if the iron is connected with the sulphide by means of a platinum wire. But in all the samples of fused sulphide I have obtained, if the iron is allowed to remain in contact with the sulphide for a certain time (which varies with different samples of the fused sulphide) and is then removed, solution of the sulphide continues. Zinc, tin, and magnesium have the same effect as iron. In hydrochloric acid aluminium acts more rapidly even than iron. In sulphuric acid it has little if any effect. Copper in HCl, when brought in contact with the fused sulphide, dissolves quietly without evolution of gas. The solution of copper chloride formed becomes,as it flows down over the sulphide, converted into copper sulphide.

Jan 1, 1887

By R. R. Morral, F. M. Krill, K. T. Aust

THE occurrence of twins in aluminum ingots cast under certain conditions has been well established. For instance, Herenguel and Lacombe1,2 have observed a twinned columnar structure in 99.5 and 99.9 pct Al, solidified by continuous or semicontinuous casting. The structure, which they termed "basaltic," appears in the form of elongated crystalline fibers of alternating luster. Herenguel and Lacombe2 found sections of flat crystalline plates composed of twin crystal plates, in which the twin plane (111) and a [I121 direction contained in the twin plane are parallel to the principal heat gradient. This orientation relationship is different from the usual orientation texture observed in cast face-centered cubic metals, where the [100] direction is approximately parallel to the long columnar axes lying in the direction of growth." A large amount of twinning has also been observed by the present authors in semicontinuous cast aluminum of 99.2 pct purity, Fig. 1. Mondolfo4 has suggested that the twinned cast structure forms by a deformation twinning process as the result of uneven cooling stresses within the ingots. This suggestion appears to be inconsistent with the large amount of twinning observed in the semicontinuous cast ingots and with the large difference of dendritic

Jan 1, 1953

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922

By Schwartz M.

Respect for mining in Botswana is long-standing. This article looks at Africa's most transparent mining regime and some of its ambitious plans. Botswana's mining industry value is forecast to average 5.2% growth from 2014-2018 with solid growth for the diamond sector and acceleration of coal production. Respect for the country's mining regime is maintained in the Fraser Institute 2014 annual survey where Botswana occupies the 26th position of 122 administrations. Botswana's transparency is illustrated by Mupane gold mine near Francistown, Ghaghoo diamond mine in the Gope area and the Morupule coal mine

Mar 1, 2015

By W. M. Gray

The determination of the state of stress existing at a point in any solid body requires the determination of the six components of the stress tensor relative to a convenient set of axes. One general method of doing this in rock is to make strain or deformation measurements associated with local relief of stress in a number of boreholes penetrating a limited volume in the vicinity of the point at which the stress is to be determined. The stress is assumed to be constant throughout this volume. Leeman1 has described a number of the instruments that have been developed for making deformation or strain measurements in boreholes. Panek2 has described the application of statistical methods to the determination of the average components of ground stress from sets of measurements made in boreholes by means of deformation meters of the type developed by the U.S. Bureau of Mines. In this paper attention is given initially to the strain cell developed for use on the flattened ends of boreholes by the Council for Scientific and Industrial Research (CSIR) , South Africa. The equations required for evaluating the average components of ground stress from measurements made by means of the CSIR strain cell are derived. These equations are similar in form to those applying to measurements made by the borehole deformation meter developed by the U.S. Bureau of Mines. The results of an investigation of the properties of the equations are described. These results are important in the practical use of both the instruments mentioned above and any instrument based on similar principles.

Jan 1, 1968

By A. J. Sinclair

Abstract-Exploratory data evaluation is an essential part of every high quality, mineral inventory estimate. Efficient analysis involves a thorough organization of available quantitative data that are the basis of the estimate and perhaps the formation of composite grades. Data organization and evaluation can involve more than 50% of the time necessary to conduct a mineral inventory estimation. The principal purpose of exploratory data evaluation in mineral inventory work is to improve the quality of estimation by providing insight into characteristics of the variables under investigation. Specific aims include: (1) to recognize and eliminate errors; (2) to provide a comprehensive knowledge of the statistical characteristics of all variables of interest for resource/reserve estimation; (3) to document and understand the interrelationships among the variables of interest; (4) to recognize systematic spatial variation of variables such as grade and thickness of mineralized zones; (5) to recognize and define distinctive geological domains that require independent estimation of mineral inventory; (6) to identify and characterize outliers; and (7) to evaluate similarity/dissimilarity of various types of raw data, especially samples of different supports. These aims are not mutually exclusive but they can all have their own impact on resource/reserve estimation. Error must be minimized. Individual variables can have characteristics that lead to different decisions in the course of estimation. Similarly, interrelations of variables might contribute to the ease (or difficulty) with which estimates of several variables can be obtained. Trends can impose the need for two or more domains, each of which might be estimated independent of the others. Outliers, a perennial problem, require detailed evaluations because they impact on reserves much out of proportion to their abundance. Data, of widely different supports, generally must be standardized if all are to be used for purposes of estimation.

Jan 1, 1998

By Adam J. Gesing

Eddy current separators are increasingly used by the auto shredder operators to produce higher grade of nonferrous metal concentrate for recycling. While this increases the unit price of the concentrate, metal losses through inefficient metal recovery quickly offset the price differential. We show how to optimize the eddy current separation system at the shredder to maximize mate- rial throughput, nonferrous metal recovery and grade of the nonferrous metal concentrate.

Jan 1, 1998

By C. M. Jones

The training program developed at Sierrita over the last twelve months has led to several significant improvements in both safety performance and productivity. Our most easily quantified results have been in truck productivity, where we have also experienced a 6% decrease in truck cycle times. We feel this is due to increased skill levels and awareness on the part of our operators due to our new training effort. The cycle time improvement has resulted in an increase in Truck productivity of 6%. Costs associated with productivity training have been $160,300. This includes program development and execution costs, as well as lost productivity during the training itself. These costs are offset by $1,400,000 in savings directly attributable to the increased skill levels of our technicians due to our training effort. As such, this represents a solid, high return investment at Sierrita.

Jan 1, 1998

By Laurence Hicks

CONSIDERATION of the past work on the subject of the diffusion of chromium into iron suggested that additional information might be given by the use of X-ray spectroscopy in following the concentration changes through the diffusion zone. Grübe and Fleischbein1 packed rods of electrolytic iron in a mixture of alumina and chromium. These specimens were heated in an atmos-phere of purified hydrogen for varying lengths of time. After treatment the specimens were examined metallographically and showed the usual structure, consisting of a border of radially oriented columnar grains ending in a sharp boundary line. Reference is made to the fact that etching with certain reagents will attack only the material inside the border of columnar growth and also to the fact that polishing seems to develop a ridge at the position of the boundary between the etched and unetched areas. By chemical analysis of thin layers turned off on a precision lathe, the authors were able to obtain depth-concentration curves. These curves, reproduced in Fig. 1, show that 'in most cases a pronounced change of slope occurs, corresponding to the position of the boundary of the columnar grains. In a later paper Grübe extends his work to other systems which show the same characteristics.2 He concludes that the reason for the break in the curve is that a hindrance of diffusion occurs at the place where the regularly oriented grains of the diffusion zone meet the random grains of the interior portion, on the assumption that the diffusion velocity in one direction in a grain may be greater than in another direction, and that the grains in the diffusion zone orient themselves so as to give the maximum diffusion rate. Kelley3 points out that Grübe has failed to note that the boundary line does not consistently cross all grains and

Jan 1, 1933

United Engineering Society WALTER H ALDRIDGE J VIPOND DAVIES I V N DORR Engineering Societies Library Board SYDNEY H BALL ALEXANDER C HUMPHREYS GEORGE C SLONE JOHN H JANEWVAY Engineering Foundation Board H M BOYLSTON J VIPOND DAVIES GALEN H CLEVENGER Society for Promotion of Engineering Education WILLIAM KELLY ALLEN B ROGERS American Engineering Standards Committee GRAHAM BRIGHT GEORGE C STONE GEORGE E THACKRAY Alternates-RICHARD L LLOYD and HARLOWE HARDINGE

Jan 1, 1923

By Y. Hwang, C Kang

To understand the effect of thermal loading from HLW on the groundwater flow nearby, the coupling of TH in an equivalent porous medium is studied. Results indicate that under given conditions the alteration of groundwater flow by decay heat is localized phenomena. More comprehensive studies are underway for THM coupling. Zum Verstandnis fur die Wirkung der thermischen Belastung von HLW in der Nahe von Grundwasserstrom, ist die Verbindung von TH in den entsprechenden porigen Medium erarbeitet. Die Ergebnisse zeigen, dass unter vorgegebenen Bedingungen die Anderung von Grundwasserstrom durch Zerfallwarme lokalisiert wird. Zusatzliche umfassende Arbeiten sind fur die THM Kupplung auf dem Wege. Pour comprendre l'effet du chargement thermique de HLW sur l'écoulement d'eaux souterraines tout près, l'accouplement du TH dans un milieu poreux équivalent est étudié. Les résultats indiquent que dans des conditions données le changement d'écoulement d'eaux souterraines par la chaleur d'affaiblissement est des phénomènes localisés. Des études plus complètes sont en cours pour l'accouplement de THM.

Jan 1, 2003

By W. M. Armstrong, John A. H Lund

The paper describes an investigation of some of the tensile properties of single crystal vanadium, poly-crystalline vanadium and polycrystal-line tantalum, in the range of: W°C to -196°C. Techniques employed in the preparation and testing of specimens are discussed in detail. Some results of determinations of the temperature dependence of yield stress and ductility are given, and discussed in terms of the Cottrell-Bilby Theory of yielding. At subnormal temperatures, all the body-centred cubic transition metals in the Periodic Table exhibit; a) the "yield phenomenon" in tension, b) a strong temperature and strain rate dependence of yield stress, and c) a large decrease or complete loss of ductility. The yield phenomenon (existence of an upper and lower yield point) has been explained by Cottrell and Bilby ( 1) in terms of the dislocation-locking effect

Jan 1, 1961

By Cemal Can Maslak, Vijaya Bhushan Rao, Vidyaranya Bandi, Karsten Beckhaus

A Large Earth Cum Rock Fill, ECRF Dam is under construction at Polavaram in the state of Andhra Pradesh in India as part of an irrigation project. The Embankment crest width of the dam is 12.5m and base width is of approximately 136.75m with a stepped sloping height of 27m on both upstream/downstream sides. Once the 1.2m Thick Plastic concrete cut-off wall is constructed below the dam along the longitudinal central axis to avoid seepage, this magnificent structure will be supported on a series of Deep Mixing Columns and Stone Columns that are evenly arranged under the footprint of ECRF Dam forming a smooth transition of gradually reducing stiffness moduli of treated ground from the center of the embankment, where the foundation stresses are high, towards the edges in order to be able to progressively limit the settlements under the dam to a specified allowable limit. As such the required post treatment stiffness in case of stone columns is 2 times of the in-situ stiffness of foundation soil, whereas it is expected to be 5 times improvement for Deep Mixing as per project specifications. Laboratory testing and Field Trials undertaken successfully to verify the design.

Sep 1, 2022