Search Documents

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,' located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI'S were approximately the same as PI'S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

Information from bores in the LatTobe Valley has been accumulating for over fifty years, and the manual extraction of details has become a limiting factor in their use.Punched card equipment, installed by the State Electricity Commission for accounting purposes, was known to be available for reasonable periods, and it was suggested that this could help in the extraction of data from the voluminous records.Investigation showed that they could be substantially duplicated on cards, with consequent gains on many operations; the cards being regarded as an auxiliary to the existing records.BRIEF DESCRIPTION OF RECORDSAs a bore is drilled a continuous record of the strata is kept, together with notes on the presence of water or any unusual features which the driller may observe.When coal is struck, samples of each ten feet are usually sent for analysis.The location and surface level of each bore is fixed by surveyors, and details of dates and methods of drilling are also kept.Bores are allocated numbers, prefixed by the name of the parish within which they are drilled. Numbers are allocated in conjunction with the Department of Mines, to avoid duplication.Records of strata and analyses are kept in folders, with 100 bore numbers per folder.Standard plans are drawn, showing the locations, bore numbers and surface levels. For each bore they also show the depth and thickness of coal struck, and the total depth drilled.Cross sections are then drawn, connecting the various coal seams, which have been identified by the geologist.

Jan 1, 1960

By J. Whitford

The established crown pillar extraction method at Gold Fields Australia Ltd.’s Crusader Mine, leads to the significant dilution and poor recovery of ore due to caving of the overlying loose rockfill. The application of selectively injecting specifically developed ‘FB200’ ettringite (calcium sulphoaluminate hydrate) type cement grout into loose rockfill to form a stabilised rockfill material, enables an artificial crown pillar to stabilise the surrounding rock mass and prevent caving of the overlying loose rockfill during crown pillar extraction. Investigation of the geomechanical criteria for crown pillar extraction beneath stabilised rockfill has enabled the safe and efficient extraction of two crown pillars at the Crusader Mine. La méthode actuelle d'extraction des piliers horizontaux à la mine Crusader dont la propriétaire est le Goldfields Australia Ltd amène à une dilution sensible du minerai, à cause de l'effondrement du remblai peu compacté qui se trouve au-dessus. Par moyen d'injection sélective du coulis de ciment FB200 ettringite (sulfoaluminate de calcium hydraté) qui a été développé spécifiquement pour cette application, un pilier artificiel est crée et celui-ci empêche l'effondrement du remblai pendant l'extraction du pilier de minerai au-dessous. A la suite des études géotechniques de la méthode, deux piliers horizontaux à la mine Crusader ont été extraites, de manière efficace et sûr. Die feststehende Krone Pfeiler Extraktionsmethode beim Crusader Mine von Gold Fields Australien GmbH, führt wegen caving des overlying lockerer rockfill zur bedeutungsvollen Verdünnung und schlechtem Wiederfinden des Erzes. Der Antrag, ausdrücklich entwickelten 'FB200' ettringite selektiv zu spritzen, (Kalzium-sulphoaluminate-Hydrat) Art kittet Mörtelschlamm in lockeren rockfill, um ein stabilisiertes rockfill-Material zu bilden, ermöglicht einem künstlichen Kronenpfeiler, die umliegende Steinmasse zu stabilisieren und caving des overlying während des Kronenpfeilerherausziehens lockeren rockfill zu verhindern. Untersuchung der geomechanical-Kriterien für Kronenpfeilerherausziehen unter stabilisiertem rockfill hat dem sicheren und tüchtigen Herausziehen von zwei Kronenpfeilern beim Crusader Mine ermöglicht.

Jan 1, 2003

By L. S. Darken

IT has long been recognized that the driving force in an isothermal diffusion process may be regarded as the negative gradient of the chemical potential (partial molal free energy) of the diffusing substance. This equivalence is exactly analogous to the fact that a mechanical force is the negative gradient of the potential energy. Nernst1 in 1888 expressed these driving forces in terms of osmotic pressure, which is directly related to the chemical potential and free energy. The relationship between the diffusivity, mobility and activity coefficient of electrolytes in aqueous solution has been developed in great detail by Onsager and Fuoss2 with results which have recently been confirmed experimentally by Harped and Nuttall.3 This interpretation of the driving force in isothermal diffusion has been discussed earlier by the author 4.6 who pointed out4 that "for a system of more than two components it is no longer necessarily true that a given element tends to diffuse toward a region of lower concentration even within a single phase region"; departure from the behavior of an ideal solution may be so great that the concentration gradient and the chemical potential gradient, or activity gradient, may be of different sign, thus giving rise to "up hill" diffusion. Since, in the discussion of that paper,4 some skepticism as to the validity of this conclusion was expressed, it seemed desirable to adduce experimental evidence to support it. Evidence of such diffusion in nonmetallic systems has already been reported. For example, it was observed by Hartley11 in a series of experiments in which sodium chloride diffused from a saturated solution in about 5 pct acetone in water into a solution virtually free of salt but with essentially the same acetone concentration. Specifically, a wine glass containing crystalline salt and saturated solution was totally immersed in a large glass cylinder containing the acetone-water solution without salt; the difference in specific gravity was such as to prevent convection. Diffusion of salt was accompanied by a marked depletion 0f acetone in the wine glass; after 3 days the acetone concentration decreased from 5.37 pct at the top of the glass, where the salt concentration was low (0.93 pct), to 1.84 pct at the bottom where the salt concentration was high (21.64 pct). This "uphill" diffusion was found to be such that the partial pressure (activity) of acetone was essentially equalized throughout the system when a steady state gradient of sodium chloride was maintained. In order to demonstrate the existence of such diffusion in metals, a series of four weld-diffusion experiments was made. In these measurements pairs of steel of virtually the same carbon content, but differing markedly in alloy content, were welded at the end and held at 1050°C for about two weeks. Subsequent analysis showed that carbon had diffused so as to produce an inequality

Jan 1, 1948

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

By Joseph L. Young, Richard A. Bohling

To keep Homestake's Bulldog Mountain silver and lead mining and milling operation in southwestern Colorado workable, natural ground water and decant water from the mine's sand backfilling operation must be continually pumped from the workings. Left untreated, this water exceeds maximum allowable levels for various contaminants that may be discharged to the environment. To comply with regulations, a National Pollutant Discharge Elimination System (NPDES) permit was obtained and a mine water treatment plant for heavy metals removal was constructed in 1977. Due to equipment capacity and operational problems, and the lack of on-site technical personnel and analytic equipment, the first water treatment plant could not consistently meet permit limits. In 1979, Homestake entered into a consent decree with EPA and the Colorado Department of Health, calling for the construction of a water treatment facility to meet NPDES permit limits. Initial construction began in the spring of 1980 and the plant now produces effluent acceptable for discharge.

Jan 12, 1981

By Thomas Brownfield

The chronicle of the oil industry in Oklahoma in 1939 is one of declining production bolstered by strenuous efforts to find new pools or new producing horizons in the older, highly exploited, relatively shallow areas. Production, which averaged 608,000 bbl. daily in 1937, the post-depression peak, declined to 463,000 bbl. daily in 1938 and continued downward to 421,000 bbl. daily for the year 1939. While the state could produce somewhat more oil if demand warranted it, production in most areas is at as great a rate as could be justified on the basis of maximum efficient operation. Outlet for Oklahoma crude has been seriously affected by the increase in production in the Illinois Basin. Crude movements from the Kansas-Oklahoma area to the northeastern consuming centers averaged 314,000 bbl. daily in 1939 as compared with 397,000 bbl. in 1938. Oklahoma producers bore the brunt of this loss of market. The general production decline was accentuated by the August, shutdown of 15 days, precipitated by the action of a major crude purchaser posting a 20-cent reduction in the price of crude. The Oklahoma Corporation Commission, in collaboration with other members of the Interstate Oil Compact Commission, ordered a complete shutdown of all producing wells in order to prevent the premature abandonment of stripper wells, which might result from a prolonged period of production at prices below operating costs. The reduction in price was forestalled, most major purchasers failing to meet the cut in view of the shutdown, and the company initiating the move rescinded its action. Fear of the shutting in of oil wells, especially those making considerable quantities of water, is generally unfounded in the light of a superficial examination of the records. Oklahoma's unprorated pools, which produced 154,000 bbl. daily in May, declined to 152,000 bbl. in June and 143,000 bbl. in July. Immediately following the shutdown, the same pools produced 150,000 bbl. in September, 145,000 in October, and 145,-000 in November. Thus, while the half month's production loss in August has not been made up, the wells apparently hare produced at a greater rate since the shutdown than immediately preceding it.

Jan 1, 1940

By Thomas Brownfield

The chronicle of the oil industry in Oklahoma in 1939 is one of declining production bolstered by strenuous efforts to find new pools or new producing horizons in the older, highly exploited, relatively shallow areas. Production, which averaged 608,000 bbl. daily in 1937, the post-depression peak, declined to 463,000 bbl. daily in 1938 and continued downward to 421,000 bbl. daily for the year 1939. While the state could produce somewhat more oil if demand warranted it, production in most areas is at as great a rate as could be justified on the basis of maximum efficient operation. Outlet for Oklahoma crude has been seriously affected by the increase in production in the Illinois Basin. Crude movements from the Kansas-Oklahoma area to the northeastern consuming centers averaged 314,000 bbl. daily in 1939 as compared with 397,000 bbl. in 1938. Oklahoma producers bore the brunt of this loss of market. The general production decline was accentuated by the August, shutdown of 15 days, precipitated by the action of a major crude purchaser posting a 20-cent reduction in the price of crude. The Oklahoma Corporation Commission, in collaboration with other members of the Interstate Oil Compact Commission, ordered a complete shutdown of all producing wells in order to prevent the premature abandonment of stripper wells, which might result from a prolonged period of production at prices below operating costs. The reduction in price was forestalled, most major purchasers failing to meet the cut in view of the shutdown, and the company initiating the move rescinded its action. Fear of the shutting in of oil wells, especially those making considerable quantities of water, is generally unfounded in the light of a superficial examination of the records. Oklahoma's unprorated pools, which produced 154,000 bbl. daily in May, declined to 152,000 bbl. in June and 143,000 bbl. in July. Immediately following the shutdown, the same pools produced 150,000 bbl. in September, 145,000 in October, and 145,-000 in November. Thus, while the half month's production loss in August has not been made up, the wells apparently hare produced at a greater rate since the shutdown than immediately preceding it.

Jan 1, 1940

By E. P. Pfleider, Rolland L. Blake

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the seaarch for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines' and the School of Mines at the University of Minnesota' have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs. The objective of the specific research problem" discussed in this paper was an investigation of the cutting action of the cliamonds set in a diamond drill bit, cutting action meaning the manner in which the diamonds cut or. loosen the minerals in the rocks being drilled. In the literature on cutting action such descriptive terms are used .as: grinding, wearing, cutting, breaking, shearing, scraping, melting, and chipping. These actions were seldom described or defined. Grodzinski describes the cutting action of a single diamond in the shaping of certain types of material as "breaking out chips of the material." Brittle mate-. rials break as small separate chips, and tough materials, because of heat generated, give a continuous chip. Deeby said about diamond drills: "When diamonds are forced into the formation and rotated, they either break the bond holding the rock particles together, or they cause conchoidal fracture of the rock itself. The former action occurs when drilling in sandstones, siltstones, shales, etc. and the latter action when drilling in chert, flint, or quartz." He said that diamonds cut on the "grinding principle" but he does not define or elaborate on this action. The cutting action of diamonds on glass was first investigated about 1816 by Dr. W. H. Wol-laston, an English physicist. The best glass-cutting diamonds have a natural or artificially rounded cutting edge. This edge first indents the glass and then slightly separates the particles, forming a shallow and nearly invisible fissure. Since none of the material is removed, this action is one of splitting rather than cutting. No other reports of research work on the cutting action of the diamond were found, and further work was considered justified and advisable. It is impractical, even if possible, to observe directly the cutting action of a diamond drill bit in rock; therefore it was necessary to devise an indirect method. It was believed that a study of the following three observations would lead to a better understanding of the cutting action: 1—the appearance of the minerals or rock surface in the bottom of the hole, 2—the size, shape, and other characteristics of the drill cuttings, and 3—the condition of the diamonds in the bit. The cutting action in a particular rock probably varies with bit pressure and speed. If the bit were slowly lifted off the rock, the effect of decreasing pressure might obliterate those bottom hole characteristics that are specific at the test pressure. Likewise, if the drill were stopped with the bit still in contact with the bottom of the hole, then decreasing speed effects would tend to obliterate the characteristics at the set test conditions. Therefore, in order to preserve those cutting effects impressed on the rock at test conditions, it seemed necessary to lift the bit off the bottom of the hole almost instantaneously once drilling conditions, i.e., revolutions per minute, pressure, and water flow became constant. In addition to observing the cuttings, the bit, and the bottom of hole, it seemed desirable to collect some quantitative data for purposes of correlation with the observations and for a record of bit performance. Consequently such data as revolutions per minute, force applied, and rate of advance of the bit were recorded. Six rock types, listed in Table I, were chosen for the tests. It was felt that these rocks had most of the variable characteristics of texture, bonding, and mineral hardness met in the common rocks generally being drilled. The sandstone was so poorly cemented as to be friable, even though most of the cement was silica. The limestone, though well cemented, was quite porous. Originally it was planned to conduct the tesk work with a full-scale drill unit, using EX bits, 7/8-in. core, 11/4-in. OD. The drill worked well, but was too cumbersome for rapid, accurate drilling of many short holes (1 ½-in.) in varied rock types. A new

Jan 1, 1954

By A. C. Richardson

[During the past two and a half sears the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive studs of coal preparation in the State of Alabama. Considerable time has been devoted to the studs of the washing characteristics of the Mars Lee bed and the various methods used In preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery of the Republic Steel Corporation, Sayreton, Ala. WASHERY PRACTICE The Mary Lee bed is very bony, and operators find it difficult to produce from this bed a washed coal much under 10 per cent ash. Experience has shown that in the preparation of a coking coal from the Mary Lee bed it is best to use a process which permits the recovery of a middlings product. Middlings are desirable because separation according to specific gravity is never perfect, and a middlings product makes possible a low ash in the primary warned coal without excessive losses of combustible in the refuse. The general washery practice on the Mary Lee bed is to crush the run-of-mine coal through some maximum screen size and wash it upon some one type of jig without re-treatment of any of the products made. The maximum size treated varies from 3 inch to J inch. The middlings product from multiple-cell jigs is usually termed "boiler fuel" and when possible is utilized as such. At present the production of boiler fuel is often in excess of power requirements, and the surplus, due to its high ash content, becomes waste.]

Jan 1, 1931

By M. E. Gershon

Software for coal blending has gained a lot of recent attention as micro-computer programs have come on the market. Some of this software is appropriate and some is not. This paper looks at the types of models being used and points out the strengths and weaknesses of each. Recommendations are then made concerning the level of detail required for these programs, relating this concern to the various ways in which coal companies are using these programs. A checklist of company requirements for these programs and available pro-gram-features provides an aid in matching the program to the company.

Jan 1, 1988

By Henry N. McCarl

Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in port- land cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggre- gate materials. The value of mineral aggregate materials at the production plant varies from less than a dollar per ton to several dollars per ton for most crushed stone and sand and gravel, $2 to $15 per ton for slag and expanded clay or shale aggregate, to as much as $60 to $100 per ton for expanded perlite or vermicu- lite. The more specialized the use, the higher the price-although there are naturally some exceptions to this rule of thumb. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Light- weight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks there will also be some coverage of sources, mining and production, especially in those cases where they are

Jan 1, 1975

By M. Girgis

The behavior of arsenic III during electrolytic refining of copper in acidic copper ?sulphate electrolytes was studied by different electrochemical methods such as, linear potential sweep, cyclic voltammetry, chronoamperometry and chronopotentiometry. The study showed that arsenic behaves as a depolarizing ion and has a deleterious effect on copper deposit. Three substrates; Pb, Cu and Ag were used during the refining process and the electrode kinetics were found similar for both Cu and Pb electrodes while a little difference was found for the Ag electrode. A microscopic study by scanning electron microscope was undertaken to show the influence of arsenic on deposit's morphology. Surface analyses of the deposit were carried out by some electronspectroscopic techniques such as Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). The results showed that arsenic coexists with copper deposit at potential?~ -0.25 V.

Jan 1, 1987

By W. D. Bryson

This paper is one of a series being prepared by the United States Bureau of Mines on tunnel-driving methods. The practices described are those used at No. 11 mine of the Colony Coal Co., Denver, Colo. No. 11 Mine is situated at Dines, some 14 miles north of Rook Springs, in Sweetwater County, Wyo. It is served by a spur off the Winton branch of the Union Pacific Railroad. The Colony Coal Co.'s mines were opened in 1918, and since that time have been among the largest producers of coal for the railroad and domestic markets in the Rock Springs coal district.

Jan 1, 1932

By Mario Cedrón Lassus

El presente texto señala los principios de excavación de túneles y el uso de la máquina tunelera denominada TBM (del inglés Tunnel Boring Machine) en el proyecto Hidroeléctrico de Carhuaquero. Así también refiere las pautas para la selección de equipo, estimación de rendimientos y análisis de costos. Finalmente se analiza las ventajas del sistema comparada con las de método convencional para la excavación de túneles.

Nov 1, 1983

By T. Feldmann, G. P. Demopoulos

The adsorption of gold complexes on inorganic metal oxides has been mainly discussed in geochemical literature, but it is also of interest to the hydrometallurgical industry. This is so because it could be responsible for valuable metal losses or because it could potentially serve as alternative adsorbent material to activated carbon in certain cases such as from hot and acidic process slurries. This paper constitutes an early investigation into this subject by focusing on the effectiveness of FeOOH, Fe3O4 and Al2O3 as sorbent materials. All tests were done in a batch stirred-tank reactor under atmospheric conditions with synthetic gold(III)-chloride solutions at 23°C and 80°C, in the pH range of 1.6 to 9.0. Detailed kinetic tests were performed at different pH values (3 and 6) on FeOOH and Fe3O4 with solutions having gold concentrations from 5 mg/L to 130 mg/L. The adsorption of gold was found to be best both in terms of kinetics and loading characteristics at 80°C and pH=6. This was explained by a change in Au(III)-Cl speciation from a gold(III)-chloride complex to a gold(III)-chloride-hydroxy complex. By far, magnetite (reagent grade chemical) yielded the best gold adsorption characteristics making it an interesting sorbent material for further development considering that it can be advantageously recovered from slurry streams via magnetic separation. On the other hand, the tendency of gold(III)-chloro complexes to adsorb on metal (hydro) oxides needs to be taken into account to minimize undesirable metal losses in chloride-containing leaching media.

Jan 1, 2015

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961