Search Documents

By T. E. Walsh

Introduction I will address two important alternative energy resources, solar and geothermal, with emphasis on their potential application in electric power generation. As a result of this presentation, I hope to leave you with a realistic view of the principal technology options that are being developed or that are available. Solar Types of Collection In terrestrial solar applications, the biggest challenge is to find ways of collecting the sun’s relatively low intensity energy so it can be converted economically to useful thermal or electric energy. Fig. 1 shows that there are both natural and technological ways of collecting solar energy. In nature we find that solar energy aids in the production of biological growth, rainfall, and wind, all of which can, in one form or another, be put to use in the production of heat or electric power. The sun’s rays also are collected and stored naturally in the form of heat in the upper layers of the ocean which can be put to use in the production of electric energy by means of ocean thermal energy conversion (OTEC) approaches. On the technological side, the sun’s rays can be intercepted by materials that directly absorb and convert its energy to low-grade heat, or by mirrors or lenses that focus the rays onto a material to produce high-temperature heat. The higher temperature systems can be used to drive efficient heat engines in the production of electricityy. The sun’s rays also can be collected on photosensitive materials, in either a direct or concentrated form to generate DC electricity directly. The systems I will discuss employ all of these means of collection and conversion, excluding biological and hydroelectric. The former is too ex

Jan 1, 1980

By T. E. Walsh

I will address two important alternative energy resources, solar and geothermal, with emphasis on their potential application in electric power generation. As a result of this presentation, I hope to leave you with a realistic view of the principal technology options that are being developed or that are available. Solar Types of Collection In terrestrial solar applications, the biggest challenge is to find ways of collecting the sun’s relatively low intensity energy so it can be converted economically to useful thermal or electric energy. Fig. 1 shows that there are both natural and technological ways of collecting solar energy. In nature we find that solar energy aids in the production of biological growth, rainfall, and wind, all of which can, in one form or another, be put to use in the production of heat or electric power. The sun’s rays also are collected and stored naturally in the form of heat in the upper layers of the ocean which can be put to use in the production of electric energy by means of ocean thermal energy conversion (OTEC) approaches. On the technological side, the sun’s rays can be intercepted by materials that directly absorb and convert its energy to low-grade heat, or by mirrors or lenses that focus the rays onto a material to produce high-temperature heat. The higher temperature systems can be used to drive efficient heat engines in the production of electricityy. The sun’s rays also can be collected on photosensitive materials, in either a direct or concentrated form to generate DC electricity directly. The systems I will discuss employ all of these means of collection and conversion, excluding biological and hydroelectric. The former is too exi

Jan 9, 1980

By A A. Puhalovich

The placement of chemically reactive mine wastes in mined out pits (æpit backfillingÆ) is increasingly seen by industry as best practice to manage long-term environmental risks. This is primarily because leaving wastes at the surface, or allowing pit lakes to develop, can result in unacceptable environmental risks. The costs and practicality of mitigation options such as installation of covers and community expectations of landform re-construction to achieve a post-mining, beneficial land use are also important drivers for pit backfilling.Pit backfilling can significantly reduce the post-closure risks to receiving environments, by minimising seepage due to tailings, acid/solute generating waste rock and/or salts derived from mine water treatment. Environmental risks are often highest where wastes are located close to the ground surface, due to relatively high rates of groundwater movement in near-surface aquifers and/or failure of engineered structures due to rainfall/erosion processes. Placement of these wastes at significant depth in pits, subject to mine planning and environmental assessment, can address these risks by increasing the path length and resistance from contaminant source to receptor, thus enhancing encapsulation of the wastes.Pit backfilling can also be cost-effective for mining companies. This is because existing pits are developed on the basis of an economic return and thus provide an opportunity to store tailings in an existing æengineered structureÆ at little or no incremental cost when compared with building and operating a new tailings or waste rock storage facility, often encompassing complex cover/drainage management systems. Key issues for consideration are mine planning, the long-term geotechnical behaviour of the wastes (eg consolidation of tailings which leads to release of acid/solutes in tailings porewaters), seepage rates to downstream receptors/agreed end point criteria and potential resource sterilisation. Internationally, mine closure guidelines are also showing a greater recognition of pit backfilling in the context of allowing mining companies to meet agreed post-closure land use objectives.In summary, pit backfilling can enhance the encapsulation of chemically reactive mine wastes and environment protection, and with agreement on post-closure beneficial land use, can also help to deliver post-closure benefits to communities.CITATION:Puhalovich, A A, 2012. Pit backfilling - Managing chemically reactive mine wastes and achieving rehabilitation objectives, in Proceedings Life-of-Mine 2012 , pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By T. G. Fulmor, William Wraith

What impelled The Anaconda Company to dismantle and move a concentrator 25 miles that was already operating at a rate of 35,000 ton per day? The answer to that question takes in almost exactly 49 years and perhaps 10 complete cycles of the metallurgical wheel in the Anaconda, Mont., mill. One could say with truth that the move is a logical next-step in the development of metallurgy in The Anaconda Co. In the old concentrator at Anaconda, the background story is unfolded: - Gravity separation by jigs, later supplemented with gravity tables, 1905. - Separate sand and slime froth flotation, 1915. - Acid bulk froth flotation, 1917. - Bulk alkaline flotation, 1926. - Alkaline flotation of total ore without sand- slime separation due to change in ore type. 1939.

Jan 5, 1964

By Eric Konigsmann

"Omai Gold Mines is a large scale open pit gold mining operation located in central Guyana, South America with a 12,000 tonne per day milling facility. Mill operations were initiated in December 1992 with commercial production beginning in January 1993. The entire operation employs approximately 120 expatriates and some 800 Guyanese nationals and is expected to produce in excess of 250,000 ounces of gold per year. The total mineable reserves contain 2.5 million ounces of gold with a projected mine life of twelve years.The milling circuits feature an SABC grinding circuit, gravity concentration and a conventional CIP gold recovery circuit. This paper will review the mill start up and ""run-in"" phase during the first year of operation. Emphasis will be placed on descriptions of start up problems and circuit modifications, mill performance trends in 1993, and personnel training and development. An outlook for 1994 is also given.IntroductionOmai Gold Mines is a large scale, open pit gold mining operation located in the Potaro district of Guyana, South America, some 160 kilometers south of the capital city Georgetown. Although there are numerous small scale gold mining ventures in Guyana, particularly with the dredging operations on the rivers, Omai is the first hard rock, open pit mine to be developed in the country. At present, this mining operation is one of the largest gold mines in South America.The Omai gold deposit has been exploited for over one hundred years. In the late 1800's, a German syndicate used hydraulicing with subsequent gravimetric separators such as sluice boxes and trommel screens to recover gold from saprolite, a soft, oxidized, claylike mineral which covers much of the claim area. Through the early 1900's and up until the 1950's, numerous mining companies including Anaconda Mining Co. Ltd. explored and drilled the Omai deposit but the technology and low gold price of the day made the reserve uneconomic to develop."

Jan 1, 1994

By C. W. Chiaretta

Utah Power and Light Company's Deer Creek Mine had been developed to a point where mine ventilation efficiency had declined to an unacceptable level. Problems identified were ventilation of inactive areas, excessive leakage, and restrictions in the return and intake air ways. Mine management implemented an intensive mine ventilation improvement program to alleviate future problems with respirable dust in the working sections and diesel equipment emissions. Program objectives included sealing of inactive areas of the mine, rehabilitation of high resistance areas, and construction of additional intake and return aircourses. Applications of computer modeling techniques are used to predict the effects of ventilation changes and improvements. Improvements are then prioritized to achieve the largest efficiency increases first. Actual real time assessment of the mine environment and ventilation changes are accomplished with a mine wide monitoring computer system. The Deer Creek ventilation improvement program has more than doubled the ventilating efficiency of the mine.

Jan 1, 1990

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

By Milson de Andrade Júnior

A central termoelétrica número 1 (CTE#1) da Companhia Siderúrgica Nacional possui duas caldeiras em operação denominadas 8 e 9 com capacidade total de produção de vapor de 200 Toneladas por hora. Estas caldeiras fornecem vapor para os turbo geradores e turbo sopradores da CTE#1, além de vapor de processo para a Usina Presidente Vargas (UPV). As caldeiras entraram em operação em 1982/83 e seus sistemas de controle e instrumentação eram totalmente pneumáticos. Ao longo do tempo foi surgindo dificuldades para reposição e manutenção dos componentes pneumáticos, motivo pelo qual se iniciaram os estudos para substituição deste sistema. Em 2009 teve início um projeto para substituição do controle pneumático por um controle microprocessado feito por PLC redundante trabalhando com um supervisório scada e para substituição das malhas de instrumentação pneumática por instrumentação em rede fieldbus. A substituição completa dos componentes pneumáticos foi concluída em 2012. O novo sistema implantado trouxe diversas melhorias na performance, confiabilidade, segurança operacional e ergonomia. Este trabalho apresenta as causas que motivaram o projeto em questão, a metodologia utilizada para a sua implantação e os resultados alcançados com a aplicação de tecnologia moderna para controle e instrumentação de caldeiras.

Jul 31, 2018

By John Bevan

In a discussion of the personal dangers that may arise from mine gases, it is necessary to take into consideration the gases which may result from an underground fire, or a fire in or about the downcast shaft, and the methods of avoiding or minimizing the danger arising therefrom. In all cases of the combustion of carbonaceous material such as coals and timber, carbon dioxide and water vapor are formed. In cases where the air supply is limited, some carbon monoxide is produced, the quantity varying with the readiness with which the oxygen from the air can get into intimate contact with the consuming carbon; in addition to these products there may be produced large volumes of irritating fumes consisting of unconsumed vapors' distilled from the burning material. Apart from the physical distress that may be caused by the irritant action of the fumes, the chief danger to life underground arising from a fire in or about the downcast shaft or intake airways is due to the carbon monoxide which the smoke is almost certain to contain. The physiological effects of this gas have already been discussed in mining papers and ref¬erence should be made to this. The prevention of fires at the surface near to the mouth of the downcast shaft, or in the shaft itself, or at the bottom of the shaft, usually lies outside the duties of the fireboss. An outbreak of fire at such places would, however, immediately foul the air current passing into the mine, and, assuming the men were in the mine, create a situation demanding urgent attention of the fireboss. As a rule, each case of fire creates its own problems, but in all cases the guiding principle should be to restrict the poison-laden 'air to the smallest part of the mine that is practicable, by opening separation doors, or breaking down selected stoppings at the most accessible points near the seat of the fire, so that the gases and smoke may pass directly into the return and so to surface. In the case of a shaft fire it will have the effect of fouling both shafts and in the case of a fire in an intake airway, both roadways leading to the shafts. It requires the use of some judgment. Therefore, in circumstances as to whether men inside the mine should attempt to escape to the shafts or should remain in the mine, and attempt to protect themselves from the poisonous air by suitably short circuiting the air-current and retiring from the main air-ways. In order to make such restraint easier, it is very desirable that all mines should be equipped with telephone communication from all sections of the mine to the surface so that men in the mine may be informed of what is being done at the surface to secure their safety, or instructed as to what they themselves should do. In cases of fire in or about the shafts, the question of the reversal of the air-current will probably arise. Should this be decided on by the management at the surface, the fireboss in the mine may have to give some attention to the effects which this action will have on the circulation of the

Jan 1, 1922

By W. F. Guenther

The usual hand-operated drilling outfit consists of a 4-in. post-hole auger with 3/4,-in. pipe for drill stem, in 4-ft lengths, with a turning handle fitted to a top pipe T. The auxiliary tools are: a chisel-bit drill made from 3/4 or 7/8-in. tool steel welded to a 4-ft length of 3/4-in, pipe, so that the regular pipe string can be used; also a churn or "mule foot" made from 3-in. pipe, slotted on one side, belled to a 4-in. tempered cutting edge on the bottom, all welded to a 3/4-in. coupling by a yoke. Other tools required are pipe wrenches and cleanout tools made from old auto springs (Fig I). A 4 1/2 or 5-in. collar welded to a plate is often used to protect the mouth of the drill hole. In general the auger is used in the typical clay overburden and brown phosphate matrix, which is relatively soft. The churn or "mule foot1' is used in hard pan, lump phosphate or cherty ground. The drill is used for breaking flint, often found loose in the overburden. The drill with the chisel bit is used for trimming sides of the hole, sounding for lime bottom and breaking through hard lumps. Holes have been drilled to a depth of 80 ft, but the limit of efficient operation is about 50 ft. In deep holes it is necessary to unscrew the string in 20-ft lengths, to

Jan 1, 1948

By W. F. Guenther

The usual hand-operated drilling outfit consists of a 4-in. post-hole auger with 3/4,-in. pipe for drill stem, in 4-ft lengths, with a turning handle fitted to a top pipe T. The auxiliary tools are: a chisel-bit drill made from 3/4 or 7/8-in. tool steel welded to a 4-ft length of 3/4-in, pipe, so that the regular pipe string can be used; also a churn or "mule foot" made from 3-in. pipe, slotted on one side, belled to a 4-in. tempered cutting edge on the bottom, all welded to a 3/4-in. coupling by a yoke. Other tools required are pipe wrenches and cleanout tools made from old auto springs (Fig I). A 4 1/2 or 5-in. collar welded to a plate is often used to protect the mouth of the drill hole. In general the auger is used in the typical clay overburden and brown phosphate matrix, which is relatively soft. The churn or "mule foot1' is used in hard pan, lump phosphate or cherty ground. The drill is used for breaking flint, often found loose in the overburden. The drill with the chisel bit is used for trimming sides of the hole, sounding for lime bottom and breaking through hard lumps. Holes have been drilled to a depth of 80 ft, but the limit of efficient operation is about 50 ft. In deep holes it is necessary to unscrew the string in 20-ft lengths, to

Jan 1, 1948

By P. O'Connell, J. Lever, C. Clemence

The Bulyanhulu Mine, Tanzania is constantly trialing ideas for improvements in the drill and blast process. The project work has resulted in a large number of choices in explosive type and charging methods being available for blast design. Interestingly, though booster sensitive bulk emulsion had been introduced to the site to reduce dilution, better results were being obtained from reduced charge columns (decoupled columns of poured anfo in 50mm pvc pipe) and pneumatically loaded anfo upholes, which had been traced. In order to compare the explosive type and charge up-methods, an explosives comparison trial was performed.

Jan 1, 2006

Experimental Validation of a Flotation Cell Model

Sep 13, 2010

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

By Prince Lazarovich, Hrebelianovich

I WAS asked by the chairman of one of the Sessions on Employment Problems to talk about the viewpoint of the foreign workingman. I am not a workingman. I have never done what a work-hand might call an honest day's labor; that is, I have never been in a factory or manufacturing plant or in a mine, though in truth, hard work and I are well acquainted. I was a soldier, am an engineer, have long been actively interested in the most important waterway construction in the near East, have served politics and diplomacy, written books and lectured at universities. My knowledge of the foreign workingman in this country comes from the fact that my own compatriots here at various times came to me and appealed for advice and help, and last year I was asked by the employment manager of a corporation to undertake a welfare job at one of their plants. I went out, saw the plant, talked with the superintendent and outlined certain of my ideas which he personally heartily approved, but which did not find favor with those higher up. I approach the subject of the foreign workman's point of view with the understanding that the industrial employer's effort is for the maximum of efficiency. I am conversant with labor conditions abroad both in industry and agriculture. What I have learned of industrial conditions in America as they affect the foreign immigrant has been chiefly gathered from the cases referred to of foreign workmen who from time to time have come to me with their troubles. In the course of those investigations, in order to give whatever help or advice was possible, I have been impressed with the fact that the great United States industries evidently had- pot yet sufficiently recognized the value of studying the conditions of the workingman in the lands of his origin across the seas. A careful study of that which could be called the moral element in connection with its foreign labor would give industry a knowledge of the man's reason for coming, what' grievances he brings with him, his hopes for a future, and the peculiar character of his capacities. The employer would thereby be enabled to meet the man, to be helpful to him, to aid him and at the same time promote industrial efficiency, inasmuch as a workman who believes that he is being dealt with humanly and squarely is contented and satisfied and will give willingly, and even with pride, the best that is in him; justice and a fair deal is all the man wants.

Jan 4, 1918

By L. S. Darken, H. A. Wriedt

An investigation has been made of nitrogen absorption by the lattice defects in a low-carbon steel afte~ Plastic deformation. Specimens in which defects were distributed by various combinations of cold rolling and vacuum heat treatment were equilibrated with controlled ammonia + hydrogen mixtures at 300° to 450°C to study the relation between the solubility and the thermodynamic activity of nitrogen. The results are interpreted in terms of nitrogen being absorbed upon two different types of defect sites, called A sites and B sites. The concentrations of these sites are calculated for specimens with various histories of straining and annealing; and the thermodynamic relations descrihing the equilibrium distribution of nitrogen among the A, B, and ordinary interstitial sites in ferrite are evaluated as follows: THE generalization that the solute atoms in a solid solution interact with imperfections in the solvent lattice is now universally recognized and the subject of an extensive literature. All types of imperfections—point, line, or surface—exhibit these interactions, but the relative importance of each type depends upon its concentration, the strength of its interaction with the particular solute atom, and whether the interaction is attractive or repulsive. The strength and sign of the interaction vary with the vectorial displacement of the solute atom from the imperfection in the crystal. The concentration of lattice defects increases during plastic deformation and the effect of the imperfections upon the solute atoms is usually perceived only after cold work or irradiation. Two experimental methods have previously been used to observe the effects of interaction between nitrogen atoms and lattice imperfections in a iron. Internal friction, which was first used for this purpose by Dijkstra,1 has been applied more often than the electrical-resistivity method of Cottrell and Churchman.2 The method of the present investigation has not been used before.* Uniform specimens of steel with a metastable defect structure are produced by cold rolling and subsequent heat treatment below the recrystallization temperature. Variations in the defect structure are obtained by varying the amount of strain and the heat-treatment conditions. The specimens are then saturated with nitrogen at moderately elevated temperatures in ammonia + hydrogen mixtures having various thermodynamic activities of nitrogen below saturation with Fe4N. From the nitrogen contents of analyzed samples, the metastable equilibria of interactions between the defects and nitrogen can be established and the concentration of sites for nitrogen atoms in the lattice defects calculated. A steel was used in the present experiments instead of purified iron or iron alloys because the amount of nitrogen absorbed at defects is larger in the steel over a much wider range of experimental conditions and could therefore be measured more accurately. The effect of alloy composition is discussed in Part II of this paper; it is sufficient to say here that impurities and phase heterogeneity in ferritic alloys favor the generation and/or retention of larger defect concentrations during plastic deformation and annealing at 300° to 500°C. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental specimens were prepared from stock of a low-carbon steel, which will be called "X steel" here, with the composition: C, 0.12 pct; Mn, 0.43 pct; P, 0.010 pct; S, 0.034 pct; Si, 0.007 pct; As, 0.086 pct; Cu, 0.022 pct; Ni, 0.009 pct; Cr, 0.003 pct. The stock was all from a single ingot made by the basic open-hearth process, which was hot-rolled to strip 0.080 in. thick.. This hot-rolled strip, given the code designation "XH", was the starting material for preparing a series of cold-rolled sheets. The latter are designated "XC27",

Jan 1, 1965

By Harold R. Kokal, Madhu G. Ranade

A metallurgical/flux is a substance that is added to combine with gangue (unwanted minerals) during ore smelting, with impurities in a molten metal, or with other additives in metal refining processes to form a slag that can be separated from the metal. Because slags are immiscible with the metallic melt and are of lower density, a separation of the slag and metal occurs if the viscosity and surface tension are of the proper values. The chemistries of slags are adjusted to provide the proper melting point, viscosity, surface tension, conductivity, specific heat, density, or chemical properties to effect the desired task. In addition to absorbing impurities from the metal, the purposes of the slag are to thermally insulate the metal bath, protect the molten metal from the atmosphere, and control the chemical potential of the system. Several excellent references on slags and metallurgical fluxes are available (Boynton, 1980, Lankford, Jr., et al., 1985, Turkdogan, 1983, Rosenqvist, 1974, Fine and Gaskell, 1984). The function of the slag might vary at different stages within a process prior to final melting. For example, the slag composition and behavior will change as materials descend in the iron blast furnace, or as they melt in the early stages of formation of steel- making slags. Selection of the chemistry for a slag might be influenced by factors outside the primary function as when blast furnace slags are used to make cement, rock wool insulation, or fertilizer supplements. Sometimes slags contain a sufficient amount of valuable recoverable elements to be sold as raw materials for other processes. Fluxes are often referred to as acid, basic, or neutral. Acid fluxes are those that generally form acids in water and bases are those that would generally form bases in water. Typical acid fluxes are silica, alumina, and phosphorus, although alumina can function as either an acid or base. Typical basic fluxes are lime and magnesia. Fluorspar, or calcium fluoride, is a neutral substance because it can be viewed as the reaction product of a base and an acid. The degree of acidity (ratio of acids to bases) or basicity (ratio of bases to acids) is often specified to characterize the slag chemistry for a particular system. The system might also be referred to as acid or basic depending on the choice of slag, for example, basic steelmaking uses slags with more bases (lime and magnesia) than acids (silica and alumina). Many forms of minerals and compounds have been used as fluxes depending on the process requirements, availability, costs, requirements for recycling of intermediate products, and environmental concerns. Because slags are most often mixtures of oxides and silicates, fluxes are usually oxides, carbonates (which decompose to oxides) and silicates. Slags comprising phosphates, borates, sulfides, carbides, or halides have also been used (Rosenqvist, 1974, Moore, 1981, Szekely et al., 1989). In ironmaking and steelmaking, some acidic components are sometimes added. In nonferrous processes slags and fluxes are acidic with silica as the primary component, and although the use of basic flux such as limestone or lime is not extensive, some amount is used to modify slag properties and some refining slags are lime based. The production of iron is accomplished by smelting of ores, pellets, and sinter in blast furnaces with subsequent refining of molten iron and scrap in oxygen-blown processes. The electric furnace is used to make steel, stainless steels, ferroalloys, and special alloys, whereas ferromanganese is often made in blast furnaces. Fluxes are used in all of these processes, and either limestone or lime is the major flux component with some dolomite, dolomitic lime, silica, alumina, and fluorspar being used. In ironmaking, the flux is added either by direct charging or through sinter and fluxed pellets. In steel refining by the basic oxygen process, flux is added as lime and dolomitic lime that are either charged as lumps or injected as fines. Some small amount of limestone is sometimes used. Fluorspar is often added as lumps or mixed with other fine materials in briquettes. Alumina is sometimes added to blast furnaces either by direct charging of sized lumps or through sinter. Typical acid fluxes are sand, gravel, quartz rock, used silica brick, or raw siliceous ore (Lankford, Jr., et al., 1985). Olivine, which is a magnesium-silicate mineral, has been added to iron blast furnaces to enhance removal of alkalis (Lankford, Jr., et al., 1985). Alumina in the form of bauxite, aluminiferous clay, and recycled alumina brick has been used as flux. Alumina can function amphoterically as either an acid or base, for example it can form aluminum silicate in high silica slags or calcium aluminate in lime-bearing slags (Lankford, Jr., et al., 1985). Limestone (calcium carbonate) and dolomite (magnesium-calcium carbonate), or fluxstones as they are sometimes called (Boynton, 1980), and their calcined forms, lime and dolomitic lime are the major basic fluxes. In the latter cases, the carbonates are de- composed in a kiln-type process to drive off carbon dioxide that might otherwise interfere with the subsequent smelting or refining process or require expensive forms of energy to effect the decomposition (e.g., by combustion of coke in the iron blast furnace). Limestone is considerably less expensive than lime because it is not calcined; however, lime is far more difficult to handle and reacts readily with water. Dolomite and dolomitic lime are used for their magnesia content. Fluorspar is a neutral flux often used as an additive in steel- making slags to improve fluidity, but it has also been used in combination with lime as a primary slag in electroslag refining (Duckworth and Hoyle, 1969). Fluorspar is available in several grades, with the lowest grade often used for steelmaking. When the price of fluorspar has risen, substitutes including aluminum smelting dross, borax, manganese ore, titania, iron oxides, silica sand, and

Jan 1, 1994

By A. B. Van Cleave

It was first pointed out in 1934 by Gaudin (1) that the "oily" oxidation product of the alkyl xanthate ion-dialkyl dixanthogen, might be the "active flotation agent" on sulphide minerals and there have been a number of studies supporting this hypothesis (2,3,4). However, all of these studies have relied largely on electrochemical evidence. Galena, being a semiconductor, may be used as an electrode in aqueous solution and it was shown that ethyl xanthate ion does not adsorb with charge transfer in the absence of oxygen unless the potential of the galena surface is above -100 mv versus the hydrogen electrode (H2 E). At this potential the galena surface is slightly hydrophobic but does not become strongly hydrophobic unless the potential is raised to 210 mv (versus H2 E). It is suggested that, at potentials of 210 mv or above, ethyl xanthate ions are oxidised to diethyl dixanthogen and that chemisorption of oxygen raises the galena surface to this potential. On the other hand, examination of xanthated galena surfaces by chemical or physical methods (5,6,7) has failed to detect dixanthogen and it has been shown that dixanthogen may be reduced to lead xanthate at a lead sulphide surface. (5,8)*. It was suggested by Leja and Poling (5) that, as dixanthogen is a neutral molecule it would not be repelled by the negatively charged galena surface so that the adsorption was envisaged as taking place through homogeneous oxidation of the xanthate ion to dixanthogen, adsorption and reduction of the dixanthogen to a chemisorbed lead xanthate species. In paper I of this series (11) it was shown that the thiosulphate ion, which forms on galena surfaces in slurries at the pH normally used for flotation, will reduce dixanthogen. There is, therefore, the impasse that the electrochemical evidence requires that xanthate ion be oxidised to dixanthogen at the galena surface while the chemical evidence shows that the reverse reaction takes place.

Jan 1, 1973

By J. M. Carter, Rodney H. Sergent, L. E. Kun, J. T. Pressly

Underground mine service water in South Africa is used for dust suppression and cooling the environment as well as the pneumatic rock drills. Although the chilled water is not intended for potable use, it is often used as drinking water by mining personnel. Furthermore, droplets sprayed are liable to be inhaled. The water is recirculated on a continuous basis and is a potential source of infection by intestinal microorganisms or water-borne diseases such as cholera or typhoid. In order to protect the health of the underground workforce it is customary to disinfect the chilled service water, The bacteriological quality of the water is monitored by enumerating total aerobic bacteria (TAB), total coliforms (C C) and Escherichia coli (E Coli). E coli is an indicator of human faeca_l __ - -- contamination, The bacteriological standard specified by the Anglo American Corporation for mine service water is less than 3000 TA B per 100ml, less than 2 CC per ml and the total absence of E Coli. There are several disinfecting agents available for use. Among these are UV irradiation, ozone, chlorine dioxide and compounds that produce hypobromous and hypochlorous acids. Historically, the methods of treatment have been chlorine based and include the use of gaseous chlorine (surface installations only), calcium hypochlorite granules or tablets, chlorinated cyanurate tablets, sodium hypochlorite solutions and hypochlorite produced by electrolysis.

Jan 1, 1991