Search Documents

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By Harry H. Power

WORK of the Committee on Education of the Petroleum Division has been under way for approximately-one year. Although some progress has been made, further activities of the Committee are necessary in order to discuss mutual problems more thoroughly by a unified group interested primarily in this field of specialization.

Jan 1, 1944

By Dae S. Young

The paper point out a new procedure to calculate the volumetric distribution of rock fragments. The method combines the practicality of digital image processing of the rock surface with the theoretical volume calculations based on principles and laws of fractal geometry. The final volumetric distribution curve is compared with the results from traditional sieving indicating close agreement.

Jul 17, 2000

By Mario J. Arenas

El presente texto describe la geología de la mina Hércules situada en el departamento de Ancash, sus nuevas interpretaciones volcanogenéticas, el zoneamiento mineralógico, así como las condiciones físico-estructurales de las rocas en que fueron diseñadas y las operaciones del sistema mecanizado de rieles.

Jul 20, 1980

By F. Rosenblum, P. Spira

"Techniques were developed to determine the oxygen demand of sulphide ore pulps in the laboratory and in concentrators. The effect of variables which influence oxygen demand was studied, and it is shown that the oxygen demand is a measure of the degree of oxidation of the sulphide surfaces. It is suggested that in investigating the significance of oxygen in flotation, the oxygen demand of the pulp is a more suitable parameter than the dissolved oxygen content.Oxygen demand measurements are being carried out with a view to determining the effect of aeration on mill metallurgy and devising improved methods of predicting aeration requirements of sulphide ores.The importance of pulp oxidation in the flotation of massive sulphide ores has long been recognized. At the Noranda concentrator, chalcopyrite could not be floated satisfactorily without a pre-flotation aeration step because the necessary dissolved oxygen was consumed by the large amount of pyrrhotite in the ore. With aeration, pyrrhotite and pyrite were depressed by surface •oxidization, and the resulting thiosulphate level in solution gave a good indication of the end of useful aeration. 1'he present study was prompted by the need to find an alternative criterion for cases where recycled mill water may contain a relatively high concentration of thiosulphate. Preliminary experiments suggested that the rate of oxygen uptake by the pulp -its oxygen demand -might be a practical measure of the end point of aeration as well as a significant parameter in the flotation of massive sulphide ores.Although it has long been realized that oxygen is an important variable in flotation, analytical difficulties precluded detailed plant investigations. Measurements of' dissolved oxygen in mill pulps were first reported by Ralston(i) in 1929. A titration method was used, and because of the delay occasioned by the preparation of clear solution samples, the values obtained were believed to be low. It was quite evident, however, that pulps in the grinding circuit had a lower oxygen content than in flotation. More recently, Woodcock(2,3) used a polarographic probe to carry out oxygen surveys in six Australian concentrators and he generally observed a similar pattern. A large number of other solution parameters were monitored, such as pH, redox potential, reducing power, and reagent and metal concentrations, with the aim of detecting correlations among the measured variables. A few potentin.lly useful relationships were found ""or specific operations in certain plants."

Jan 1, 1974

By Willard Ide Pierce

THE native methods of mining and milling gold-ores in Korea may not present any specially new features, but are chiefly interesting as primitive practices, still followed at the present day. In mining where the rock is hard, wood is piled up near the face of the tunnel or drift and then set on fire. The fire bums for twenty-four hours, after which, three or four days are given for the rocks to cool, before the miners go in and extract the loosened material. The only tools in use are a hammer, a steel gad about five inches long, and a flat spoon-shaped basket. The pay-streak or chute is closely followed, and in places the workings are very small and intricate. Rock not yielding more than $6 per ton is not extracted. The manner of opening a mine is to begin on the outcrop, where the rock pays, sink a shaft or run a tunnel on the vein, and follow the pay-streak and more easily worked ore. When this is exhausted, or the influx of water interferes, the opening is abandoned and operations are begun again at a new spot on the outcrop. The place usually selected is as high up on the mountain as possible, and in no instance is advantage taken of the topography by running a cross-tunnel to tap the vein. The ore is brought in baskets to the surface, and there placed in sacks, holding about 150 1bs. each, and taken to be crushed. The rock is first crushed between two stones, as shown in Fig. 1. The upper stone is oval and rounded on the bottom, so that it can be readily rocked on the under stone. Two pieces of wood, used for handles, are placed, one on each side, in grooves in the upper stone, and held in position by means of straw rope. The lower stone is not smooth on top, but exhibits three elevations running lengthwise, with shallow depressions between them. The middle elevation acts as a fulcrum on which the upper stone may be rocked. From two to ten men, according to the weight and size of the stone used, are employed in rocking. With four men, from 300 to 350 lbs. of rock can be crushed per day, the stone making 50 complete oscillations per minute. The men squat on each side of the stone and move it to and fro by means of the wooden handles. The ore is fed, in pieces up to the size of an egg or even larger, by one of the men. During the crushing one man on each side, as the stone rocks from

Jan 1, 1890

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize productivity, the influence of reclamation parameters must be well understood ? which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass appraisals, and also the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, we use biomass production experimental plots on reclaimed mine sites established by the Powell River Project (PRP) for a comparative study between satellite measurements of Normalized Difference Vegetation Index and inventory estimates of biomass under a variety of conditions. The PRP is a unique public-private partnership in the coalfields of southwestern Virginia dedicated to enhancing beneficial use and environmental protection of mined lands.

Feb 27, 2013

By Denis Racicot

"L'Abitibi québécois a produit essentiellement de l’or, du cuivre, du zinc et de I' argent, ainsi que de faibles quantités de nickel, de plomb, de molybdène, de bismuth, de lithium, de fer et d’amiante. Depuis l’ouverture de la mine Horne en 1927, cent-cinquante mines ont contribué à la production de 1 420 tonnes d’or de 4,1 millions de tonnes de cuivre et de 4,7 millions de tonnes de zinc. Les productions minières annuelles ont été d'importance variable: des records de production ont été établis en 1955 pour I' or avec 35 tonnes et, vers 1965, pour le cuivre, le zinc et la quantile globale de minerai extrait avec respectivement 130,000, 275 000 et 13 millions de tonnes. Deux dépressions généralisées ont eu lieu, l’une vers 1946 et l'autre, a lafin des années soixante-dix. Des ralentissements de la production ont été observes pour le cuivre en 1953 et le zinc en 1959. Depuis le debut des années quatre-vingt. I' or et, de façon plus irreguliere, le zinc sont en progression, landis que le cuivre, malgre une hausse en 1983. pour suit son dec/in.La teneur de récupération des mines d’or est demeurée régulière et n’a subi qu’une faible diminution au cours des quarante dernières années. Célie du cuivre a diminué d'environ 50% dans la même période, landis que celle du zinc a subi d’import antes variations, aussi bien positives que négatives. Près des trois quarts des mines d'or ont une durée de vie inférieure à 12 ans et la distribution des tonnages de minerai extrait montre un maximum pour la classe de 100 000 à 1 million de tonnes. Du cote des mines de métaux de base, la durée de vie est plus étalée et les volumes de minerai ont une occurrence maximale dans la classe de 1 à 10 millions de tonnes.Concernant la distribution géographique de la production minière dans l'Abitibi québécois, le camp minier de Rouyn-Noranda vient en tête pour l’extraction de minerai et la production d’or et de cuivre. L’est sui vi par le camp de Val d'Or pour le minerai et l’or, landis que le camp de Chapais-Chibougamau occupe la deuxième place pour le cuivre avec une production équivalence a 60% de celle de Rouyn-Noranda. Le camp de Cadillac-Malartic suit de tres pres celui de Val d'Or pour ce qui est de I' or. Finalement, dans le casdu zinc, le camp minier de Joutel-Matagami domine largement avec une production qui a connu un développement accélère depuis 1963. Une analyse pré liminaire de ces données indique qu' i/ subsiste unpotentiel encore élevé de production d'or, décuivre et de zinc dans I' Abitibi québécois. ABSTRACTThe Quebec portion of the Abitibi belt has essentially produced gold, copper, zinc and silver, as well as some small quantities of nickel, lead, molybdenum, bismuth, lithium, iron and asbestos. Since the opening of the Horne mine in 1927, one hundred and fifty mines have produced 1420 tons of gold, 4,1 millions tons of copper and4,7 millions tons of zinc. Annual mine production has fluctuated: production records were established in 1955 for gold with 35 tons, and around 1965 for all extracted ore copper and zinc with respectively 13 millions, 130 000 and 275 000 tons. Two main recessions have occurred, the first around 1946 and the second during the late seventies. Cut backs in copper and zinc production occurred in 1953 and1959. Since the beginning of the eighties, gold production and to a lesser extent zinc production have been in progression. Except for a small jump in 1983, copper production is still declining.The average recuperation grade of gold mines has been quite steady and has only slightly diminished in the past forty years. The average copper recuperation grade was halved during the same time interval. For zinc there have been important ups and downs. At least three quarters of gold mines have an average lifespan of 12 years the tonnage distribution shows a peak in the 100 000 to 1 million tons class. Base metals mines show a more widespread life expectancy and have a tonnage peak in the 1 to 10 millions tons range"

Jan 1, 1990

By R. J. Folic

Investigations of the vibrations of a pile in soil are performed on a dynamic model in the form of a prismatic bar of finite axial and flexural stifnesses with a discrete mass at its free end representing the cap. The soil is represented by a system of springs of constant and variable stiffnesses. Oscillation differential equations are derived by means of the Hamiltonian principle for non-conservative systems. The problem is reduced to a coupled system of two non-linear partial differential equations with corresponding initial-boundary conditions. Frequency equations of longitudinal and lateral linearized equations are formed. The paper determines natural frequenc­ies and oscillation modes. It separately examines longitudinal vibrations excitated by a hermonic force acting upon the pile cap, and lateral vibrations excitated by an impulse acting upon the cap. The results of the numerical processing are presented in respective diagrams in dimensionless form.

Jan 1, 2010

By Alastair C. Torrance

"A brief review of the Australian mining industry is given followed by a more detailed treatment of a study of the influence of primer Size on explosive performance. This is based on a joint research programme conducted by BHP Central Research Laboratories and Dyno Wesfarmers Ltd and examined the effect of the size of cast primers on the run up and steady state detonation velocitiesof ammonium nitrate based explosives as a function of blasthole diameter. The field trials examined a numter of the Dynamo 'Westfarmers HDF series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the iun up velocity of 187 mm diameter ANFO charges is negligible using cast primers as small as 150g. However, emulsion and watergel explosives did exhibit run up in both 187 and 3:1mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blashole diameters"

Jan 1, 1991

Con el objetivo de establecer medidas preventivas y de protección a la salud del trabajador, la sección de Higiene industrial realizó un estudio a 220 minas de la zona norte del Perú para determinar el estado y las condiciones ambientales de los trabajadores en la zona minera. En este sentido, el texto señala las disposiciones de salubridad del departamento de Higiene industrial, así como los estudios realizados en los campamentos mineros de Cajamarca, La Libertad y Ancash. La investigación se realizó a 1649 trabajadores, donde solo el 23.8% contaba con ingenierio de seguridad a tiempo completo, las facilidades hospitalarias se brindaban a 84.5% de trabajadores y solo el 87.8% de los trabajadores estaban asegurados contra accidentes. Asimismo se reveló que muy pocos trabajadores contaban con métodos de control mecánico en las compañías visitadas. Respecto de los servicios sanitarios, solo el 23.8% de trabajadores disponía de comedores, el 38%, de la provisión de desagues públicos y el 37.9% con colector de basuras. En consecuencia, se vio la necesidad de crear un programa adecuado y efectivo de la Higiene Industrial, de forma que se controle la exposición de los elementos tóxicos, evitando la adquisición de enfermedades ocupacionales en los trabajadores y el desarrollo futuros riesgos ambientales.

Jul 20, 1957

By D. G. Russell

Two techniques have been developed with which the applicability of pressure build-up analyses can be extended to include pressure data which previously have been considered virtually unusable. One of the interpretation methods makes possible the analysis of pressure build-up performance during the wellbore fill-up or after production period which occurs soon after a well is closed in. The other technique is an extension of a method for analyzing pressure build-up performance during the late-time portion of the pressure build-up which occurs after boundary eflects first begin to alter the shape of a conventional pressure build-up curve. With both of these methods it is possible to obtain estitnates of the kh product, the skin factor and the reservoir pressure. In addition, with the late-time analysis technique it is possible to obtain an estimate of the contributory drainage volume of the well being tested. This means that in some cases a check on reservoir limit test and (or) material-balance calculations can now be obtained from pressure build-ups. Both methods are slightly more time-consuming than conventional pressure build-up analysis methods because trial-and-error plots of pressure data must be made. The late-time method for analysis of pressure build-ups is in principle applicable to the late-time portion of a two-rate flow test or a pressure drawdown test. The interpretation formulas and procedures for these types of tests are also outlined. In these cases, as with pressure build-ups, it is significant that an estimate of the contributory pore volume is also obtained. On the basis of limited experience with the new techniques, it appears that satisfactory estimates of the kh product, skin factor, reservoir pressure and, for late-time analysis, contributory drainage volume can be obtained. INTRODUCTION The analysis of bottom-hole pressure build-up behavior in closed-in wells has been a a subject of interest in petroleum engineering circles for many years. In fact, few other subjects have received as much attention as pressure buildup analysis methods have. The cause for this interest is essentially twofold in nature. First, the pressure behavior of a well can normally be measured with a reasonably high degree of accuracy so that good data for analysis can be obtained. Secondly, over a fairly wide range of operating conditions, valuable information as to the quality of the reservoir rock and completion efficiency of the well can be obtained at a nominal cost. In recent years, numerous papers have been prepared on the effects of various operating conditions and reservoir heterogeneities on pressure buildup behavior. Very little work has been done, however, on extension of pressure build-up analysis methods to those pressure data which are not amenable to analysis by the present methods. The theory upon which the analysis of shut-in bottom-hole pressure build-up data is based is derived from the solution of the radial flow equation for a slightly compressible fluid for constant-rate conditions. It requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed bottom-hole pressure vs log (t + ?t)/ ?t (where At is shut-in time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the formation permeability, the well damage or skin factor, and the reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. The successful application of this procedure depends on being able to recognize the straight-line section on the basic pressure build-up plot. The presently used pressure build-up interpretation theory also assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing-in to the formation. This adjustment period is commonly referred to as the "afterproduction" or "fill-up" portion of the pressure build-up. During the period that the well fill-up effect is most pronounced, the basic pressure build-up plot is nonlinear. At later shut-in times after the effects of a drainage boundary have been felt at the well, deviation from the straight-line behavior of the pressure build-up plot also results. In many cases either of these effects or a combination of both can make the straight-line portion on the pressure build-up plot difficult to recognize. Obviously, an extension of pressure build-up analysis methods to include the afterproduction period and the period in which boundary effects are being felt would be desirable and might render valuable pressure data which for years have been considered virtually unusable. The principal reference of note concerning pressure buildup analysis during the afterproduction period is a paper by Gladfelter, Tracy and Wilsey.1 In the approach of these authors it is necessary to measure the rate of influx into the well during the afterproduction period. This is done through sonic measurements or through measurement of tubing-head and casing-head pressures simultaneously with

Jan 1, 1967

By K. A. Smith, X. Cheng

Introduction The separation of minerals from complex sulfide ores by flotation requires careful control of the surface chemical behaviors of the minerals constituting the ores. When the minerals in the ore are finely disseminated, extremely fine grinding is needed to liberate the minerals. Fine grinding is not only an energy-intensive operation, but also influences the flotation behaviors of liberated minerals. Steel balls are commonly used for grinding. Galvanic interactions occur not only between sulfide minerals and grinding media but also among the different sulfide minerals themselves. The electrochemical characteristics of chalcopyrite and pyrrhotite when they are independently coupled with steel grinding media and the relevance of these characteristics to the flotation behavior of these minerals have been exten¬sively studied (Cheng and Iwasaki, 1992: Li and Iwasaki, 1992). These studies dealt with reactions in two electrode combinations, simulating mineral-grinding medium and mineral-mineral interactions. In practice, however, it is more common to involve more than one sulfide mineral. In a study of a pyrite-pyrrhotite-mild steel system, Pozzo et al. (1989) provided evidence that a mineral having an intermediate potential could behave differently, depending on the condi¬tion of galvanic contact. This investigation was undertaken to study a chalcopyrite-pyrrhotite-mild steel system to gain better in¬sight into the mechanism of multiple galvanic interactions. A three-electrode system was chosen to simulate a typical copper sulfide ore. The sulfide minerals were represented by chalcopyrite and pyrrhotite. The grinding medium was rep¬resented by mild steel. The nature of galvanic interactions involving these minerals and grinding medium in an oxygen atmosphere was investigated in a three-electrode combina¬tion, and an attempt was made to relate the laboratory flotation results of pyrrhotite-chalcopyrite ores. Possible implications to the differential flotation of complex sulfide ores are discussed. Key words: Electrochemistry, Flotation, Sulfide ores Experimental The pyrrhotite (57.74% Fe, 0.09% Cu, 4.84% Ni and 36.54% S) sample was obtained from Falconbridge Ltd.'s Strathcona mine, Ontario, Canada, and the chalcopyrite (26.00% Cu, 28.57% Fe, 0.05% Ni and 31.52% S) sample came from Transvaal, South Africa. Mild steel (AISI 1020, 0.2% C) was chosen to represent grinding media. A conventional three-electrode cell was used in the elec¬trochemical measurements. The working, counter and refer¬ence electrodes were, respectively, sulfide minerals or mild steel, graphite rod and saturated calomel electrode (SCE, 0.245 V vs. standard hydrogen electrode). The exposed areas of the sulfide minerals and grinding medium electrodes were approximately the same (0.17 to 0.19 cm2). The preparation methods of working electrodes, the reagents used, the experi¬mental procedures and the instrumentation were the same as those described previously (Cheng and Iwasaki, 1992). Rest potentials of pyrrhotite, chalcopyrite and mild steel were measured individually in 0.05-M sodium sulfate solu¬tions. Combination potentials and galvanic currents of the sulfide minerals and grinding medium were measured in short-circuited two- and three-electrode systems. All poten¬tials in this study are quoted in volts with respect to the standard hydrogen electrode (SHE). To simulate the constantly abrading conditions in a ball mill, rest potentials, combination potentials and galvanic currents were also measured by rotating a porcelain ball against chalcopyrite, pyrrhotite and mild steel electrodes in

Jan 1, 2000

By F Sahlström, E M. Jolis, V R Troll, E Jonsson, K Högdahl, C Harris

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Bastnäs-type magnetite-skarn-hosted rare earth element (REE) mineralisations are located in the Palaeoproterozoic Bergslagen ore province, central Sweden, and occur along a ca 100 km long belt of 1.90–1.87 Ga metavolcanosedimentary rocks. Ten different Bastnäs-type deposits have been sampled in order to assess the origin of ore-forming fluids in these systems. Magnetite and quartz have d18O values ranging from -2.3 to +1.1‰ and +7.2 to +8.3‰ respectively. Mineralised carbonates have d18O values between +5.8 and +7.2‰ and d13C values between -5.4 and -3.3‰. Temperature calculations based on the O-isotope composition of mineral pairs, combined with available fluid inclusion data, suggest primary mineralisation at ca 650–400°C. For these temperatures, calculated equilibrium fluids have d18O values that range from those typical of magmatic fluids (+6 to +8‰) to lower values (down to +3‰). Variation in carbonate O and C isotope data are consistent with interaction between local Palaeoproterozoic carbonate rocks (d18O = +12.5 to +19.6‰ and d13C = -1.8 to +1.7‰) and fluids of a magmatic origin. It is suggested that the Bastnäs-type REE-magnetite mineralisations formed as a result of reactions between local carbonate units and high-temperature, magmatic-dominated hydrothermal fluids during 1.90–1.87 Ga (Svecofennian) syn-volcanic activity.CITATION:Sahlström, F, Jonsson, E, Högdahl, K, Harris, C, Troll, V R and Jolis, E M, 2015. O and C isotope study of Bastnäs-type rare earth element mineralisation, Bergslagen, Sweden, in Proceedings PACRIM 2015 Congress, pp 439–444 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

I have the honor to submit herewith the report of the Secretary for the year 1915 showing the principal activities of the Institute: Meetings.-The 110th Meeting, including the Annual Business Meeting, was held in New York City, Feb. 15 to 17, 1915. The full report of this meeting is given in Volume LI of the Transactions. The number of papers presented was 53, and the attendance was 357 members and guests. The 111th Meeting was held in San Francisco, Cal., Sept. 16 to 19, 1915. Sixty-eight technical papers were presented, and the attendance was over 400 members and guests. The full report of this meeting is given in the Bulletin for December, 1915. Local Section.-A new, strong Local Section of the Institute, with head-quarters in Arizona and known as the Arizona Section, was formed during 1915. Affiliated Student Societies.-Three new Affiliated ,Student Societies were recognized in 1915 consisting of the Pick and. Hammer Club of the University of Oklahoma, Mining and Metallurgical Club of the Univer-

Jan 2, 1916

By George A. Morgan

The successful expansion of crude oil production begun in late 1977, led to promising development of the nonfuel minerals sector. Although actual production of nonfuel minerals was limited both in variety and in percentage of output on a world scale, the potential for expansion with a rapidly developing infrastructure was significant. The energy base was expanding with construction of two new hydroelectric powerplants in addition to the existing plant near Edea. The Song Loulou plant will have a 240-megawatt capacity, and a hydroelectric plant under construction in the northern part of the country by mainland China will have 72 megawatts of installed capacity. Inflation of between 15% and 20% resulted in a real gross domestic product (GDP) of $2.8 billion2 in fiscal year 1980 (July 31 to June 1), up 6% from that of the previous fiscal year. Petroleum became the leading export item in terms of value, surpassing coffee and cocoa exports. Mineral exports as a whole increased eightfold in value, mainly because of oil sales. Oil exports also caused a reduction in the trade deficit by nearly one-third, and the Government expected its 1980-81 budget to be balanced at $1.17 billion. The Port of Douala accounted for about 8 million tons of cargo, or 93% of total maritime traffic for Cameroon. Expansion plans for the port call for an initial increase to 5 million tons, and a cargo handling capacity of 7.5 million tons in 1985 and 10 million tons by 1990. The Port of Victoria will gain importance with the startup of an oil refinery. The country's third seaport at Kribi was used solely for timber shipments, and capacity at the Port was to triple by 1981. The Government operated its own shipping line with six oceangoing freighters. France was the dominant trading partner, accounting for 25%

Jan 1, 1982

By Steven J. Page, William A. Heitbrink, Andrew B. Cecala, Edward D. Thimons, John A. Organiscak

Miners at noncoal surface mining operations are often exposed to high levels of respirable dust. In an effort to lower the respirable dust exposure of these surface miners, the National Institute for Occupational Safety and Health (NIOSH) has been conducting research to address this problem in a practical and economically viable manner. One successful effort deals with lowering the dust exposure of equipment operators in enclosed cabs. Many types of surface mining equipment utilize enclosed cabs to protect equipment operators from dust exposure. Normally when the equipment is new, the cabs are fairly airtight. These tightly sealed cabs, combined with good filtration systems, generally provide the operator with good dust protection. However, most mining equipment is older, and as aging occurs, many components of the enclosure deteriorate. The structural integrity of the cab diminishes and the effectiveness of the air filtration system fails. NIOSH has been successfully researching costs-effective methods to improve both filtration effectiveness and cab integrity of these older cabs in order to provide a healthier work environment for equipment operators. Dust sampling records indicate that drill operators and helpers have the highest dust exposure of all workers at surface mining operations. Since much of the overburden contains a high percentage of silica, the health hazard associated with this dust can be even more serious. NIOSH research is addressing techniques to lower respirable dust levels at surface drilling operations. INTRODUCTION NIOSH's mission is to assure a safe and healthy work environment for the working men and women of this nation. The primary emphasis of NIOSH's Pittsburgh Research Laboratory (PRL) is mining health and safety research. This report focuses on two areas of research

By Haydn H. Murray

Since the advent of machine coated paper in the mid 1930's, the kaolin industry has had a remarkable growth, In 1935 the domestic production of kaolin was 500, 000 tons and in 1970 the estimated production was in excess of 3. 5 million tons. The process industries which use kaolin most extensively are paper, rubber, paint, ceramics, plastics, catalyst manufacturers, ink, and pharmaceutical. The paper industry is by far the largest consumer of kaolin using approximately 70 per cent of the total tonnage mined and beneficiated. Up until 1970 the major kaolin producers were able to expand rapidly enough to supply the demand but for the first time in thirty years the demand is expected to be in excess of mining and beneficiation capacity through at least 1975. The major reason for this is the expansion of coated paper production in Europe and Japan. Two areas supply the lion's share of kaolin for the world markets. These are the Cornwall area in extreme southwestern England and a limited area of Georgia and South Carolina in the southeastern U. S. The English kaolins are primary - (found in decomposed granite) whereas the Georgia-South Carolina kaolins are secondary - (found in lenticular, continuous beds in the Tuscaloosa formation of Cretaceous age. ) The English kaolins are mined by hydraulic methods whereas the Georgia-South Carolina kaolins are mined by dragline or shovel and benefidated by using a wet process for the majority of the production and/or a dry

Jan 1, 1971

By M. T. Simnad, G. Derge, Ling Yang

A method is described for using radioactive tracer for the direct determination of ionic mobility in a molten electrolyte. The ionic mobility of Fe" in silica-saturated iron silicate is found to be 0.0009 (*0.0002) cm2 sec ' volt L at 1250°C. eLECTROCHEMICAL studies', ' of molten iron eE oxide and iron silicates have shown some ionic conductivity at all compositions. The current efficiency in electrolysis increases with the concentration of silica to a maximum of 90 pct at about 34 pet SiO,. In the silica-saturated melts the transport number of ferrous ions is near unity, indicating that

Jan 1, 1957