Search Documents

By P. A. Beck, L. J. Demer

As reported in a previous publication,' isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: Here, D is the average gain size after an annealing period 1. The annealing period includes the time for complete recrystal-lization R, and the time for gain growth 1,. D, is the pain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pet magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed-effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystal-lization and grain growth of the 2 pct magnesium alloy at 350°C. Experimental Procedure The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table r and magnesium from a high purity distilled stock of magnesium crystals. Table i—Lot Analysis of High Purity Aluminum Per CeNt Si.................................... 0.00~ Fe.................................... 0.002 Cu................................... 0.002 Mg................................... 0.003 Mn................................... o. oox Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. Table 2—Ingot Numbers and Magnesium Contents Ingot Number Pct oa Magnesium aI 2.05 22 1.80 24 0.12 26 0 02s The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up to I 500X, revealed a cer-

Jan 1, 1949

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By B. Hagemeyer

The trend to higher solids paper coating and to neutral/alkaline papermaking is causing an above average growth in the use of calcium carbonate as both a paper coating and a paper filling pigment. These developments are expected to continue well into the 1990s. Thus, calcium carbonate will account for a somewhat larger percentage of total paper pigment volume. Nevertheless, overall growth in paper tonnage coupled with an increase in filler pigment percentages will create a demand for larger quantities of other pigments as well. Kaolin will continue to be the dominant paper pigment by far, with continued growth though at a somewhat slower rate than calcium carbonate.

Jan 1, 1986

By Charles M. Hauptman

The Karst asbestos deposit, discovered seventy years ago, is 32 miles south of Bozeman in southwestern Montana. The deposit is about one-half mile west of the Gallatin River which flows in a deep V-shaped valley flanked on either side by rugged mountains. The Madison range is west of the river and the Gallatin range lies to the east. A busy all-weather highway, U.S. No. 191, follows the river and is the major north-south route between Bozeman and the Gallatin valley to the north and Idaho and the west entrance of Yellowstone National Park to the south. The asbestos deposit is a large body of serpentinized peridotite in which anthophy11ite.occurs, both as distinct veins and as a disseminated mineral in the peridotite mass. The known exposures of the asbestos-bearing rock occur on a steen south slope at an "elevation of about 7000 feet, an elevation 'which is about 1200 feet above the Gallatin River. Over the years, a number of small companies have attempted to exploit the Karst asbestos deposit without continuing success. The present operator, Galaxy Mining Corporation, has attempted a systematic approach to the problem by utilizing geologic and engineering surveys to determine the economic and technical feasibility of a mine and plant to produce a finished asbestos pro-duct. The results of this work indicate a high probability of success for the project. However the company now faces that dilel1lJllB so common to the non-metallic mineral business; that is, whether to continue a research program of further mineralogical and technological studies in conjunction with detailed market surveys or to rely on the work done to date and embark on a pilot progril1n

Jan 1, 1971

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By S. Konetschnik, E. Dreyer, A. Filzwieser

"More intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetimes, making cooling technology an important aspect of furnace operations. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start-up and operation, namely hydration problems, corrosion, and explosions. Apart from these aspects, the energy that is removed by extensive cooling cannot be recovered and is normally lost in the cooling towers.With METTOP’s new patented cooling technology it is possible to overcome the disadvantages of water by using an alternative cooling medium, namely ionic liquids (ILs). The main advantage of ILs is the fact that there is no risk of explosion should this liquid come in contact with molten metal. Furthermore, ILs can be used at higher temperatures than water - up to 200°C. This relatively high cooling medium temperature avoids hydration and corrosion problems and allows recovery of the energy by combining the ILTEC system and the organic Rankine Cycle (ORC) technology, for example.Due to the removal of the explosion risk, much higher safety standards can be achieved, particularly in critical areas such as tap-holes"

Jan 1, 2014

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Last year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."' The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recant information. In other countries in which the authors are engaged in similar work, the competition between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under separate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations' between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions. Electrochemical Phenomena in Drill Holes Technical Publication 462l described the author's discovery concerning the existence of important differences of potential spontaneously gener-

Jan 1, 1934

The objectives of this paper are to introduce the International Code of Practice for Risk Management of Tunnel Works and to illustrate to the participants of the 13th Australian Tunnelling Conference 2008 how the insurance industry would like to see the future of tunnelling insurance. Tunnel construction projects have suffered large losses over the years as can be shown from various loss examples and a list of major losses over the last ten to 15 years. Since the consequences of insufficient risk control had to be borne by insurers, these losses have heightened the need for improved and adequate risk management measures so that insurance cover can also in future be provided for this hazardous industry sector. Observations are made as regards to the prevailing trends in the tunnelling industry, which contribute to the increase in risk and have adverse consequences for the insurance industry. To find a solution to this dilemma various options are examined with the suggestion of a Joint Code of Practice for Tunnel Works being agreed by all stakeholders, which would become essential to secure future insurance protection for such project work. The British Tunnelling Society has, in cooperation with the Association of British Insurers, developed such a code, which the International Tunnelling Insurance Group has now adopted for global application in international markets. The content and concept of this code is explained to establish a framework of understanding and applied risk management principles for tunnel works. This initiative also has the support of the International Tunnelling Association and the International Association of Engineering Insurers. The international application of this new code is demonstrated with a few examples, which also includes Australian projects. It is the aim that this code forms in future part of the insurance coverage for tunnelling works in order to put this risk segment on a more sustainable basis. For that reason the insurance industry is seeking the support of all stakeholders of tunnelling construction projects.

Jan 1, 2008

By Ilkka Haapamäki

El presente texto señala la planificación del proceso de ventilación Outokumpu en la mina Helsinki, Finlandia a través de la evaluación de las cantidades de aire. Este sistema se basa en normas locales vigentes para la higiene laboral, órdenes relativas a la ventilación de las minas, cantidades de producción de la mina, condiciones geológicas de la mina y cantidad local de sustancias producidas durante el trabajo de la mina. Asimismo se describe el layout del programa, preparación de la red de ventilación y simulación por medio de una computadora, planificación de la dirección del proceso de ventilación, control automático de la ventilación en la mina de Pyhasalmi, cálculo de costo, planes de investigación y evaluación del número personal requerido.

Oct 14, 1980

By R. J. Pindred

In his paper, Davis presents an overview of risk. He also introduces the Capital Asset Processing Model (CAPM) as a foundation for selecting the appropriate discount rate for a mining project. While applying portfolio theory is more defensible than the ad hoc adjustment of discount rates, the CAPM is not a panacea.

Jan 1, 1995

By M. A. EI Zeky, A. E. El-Nikbaily, M. A. Shahin

"Possible mechanisms of microsilica dust formation and factors affecting its quantity have been discussed. General mathematical models to predict the dust quantity based on electrical and coke consumptions, and flue gas temperature as functions of silicon recovery in the process and silicon content of the alloy have been established. It has also been shown that the flue gas temperature can be used as an additional process control parameter. Comments are made on the effect of the dust formation on the whole process economics and it is pointed out that the formed microsilica dust is a valuable by-product and not an industrial waste. INTRODUCTIONFerrosilicon is produced in electric arc furnaces with submerged electrodes. The charge mixture consist s mainly of quartzite, coke as the reducing agent and iron chips. The products are ferro silicon and carbon monoxide, various other volatile materials, water vapour and silicon monoxide gas. Carbon monoxide and silicon monoxide oxidize at the charge surface when mixed with air entering through the furnace hood openings. The off-gas contains a considerable amount of dust, which is mainly very fine particles of silica formed as a result of oxidation. The emission of dust containing gases to the atmosphere causes serious pollution problems to the environment. Therefore, the control of the formation of the dust, preventing it from escaping to the atmosphere, and dealing with this very fine dust collected from the flue gases represent important technological and economical parameters in the ferrosilicon production industry.This paper is concerned with the relations between the quantity of formed micro silica dust, as a function of both silicon recovery and silicon content in the alloy, and various other technological parameters; and their possible effects on the energy consumption and economics of the whole process."

Jan 1, 1989

By Omar Abd el Fattah Ramly, Abdallah Mohamed Sourour

FOREWORD In 1974, the Ministry of Housing and Reconstruction (The Client) which subsequently became the Ministry of Development and New Communities of the Government of the Arab Republic of Egypt assigned responsibility to the Arab Contractors (Osman Ahmed Osman and Company) for the design and construction of the tunnels under the Suez Canal. For this project the Arab Contractors of Cairo and Tarmac International of London formed a joint Venture, called Osmac. Sir William Halcrow and Partners of London are responsible for the design of the Ahmed Hamdi Tunnel as a Sub-Contractor to the Contractor. The advisory consultant of the client is a joint Venture between Tippetts-Abbett-McCarthy-Stratton (TAMS) of New York and Arab Consulting Engineers (ACE) of Cairo. INTRODUCTION A site investigation was carried out between Km 141 and Km 150 Suez Canal chainage to determine the ground conditions relevant to design and construction of a road tunnel under the Suez Canal. A feasibility study included aerial surveying, geological mapping and the drilling of 8 boreholes. Detailed investigation included the drilling of 105 boreholes, sampling, piezometer installation, pumping tests, and the digging of trial pits and trial excavations. In-situ work comprised SPT, permeability tests and dilatometer tests. Laboratory testing included soil classification tests, compaction tests, California Bearing Ratio tests, shear strength determination and oedometer consolidation tests as well as chemical analysis of both soil and ground water. The investigation revealed that the ground conditions at the first proposed El Shatt site (Km 148.5) were not favourable for bored tunnelling, whereas they were more favourable at the southern El Shatt site (Km 150.0).

Jan 1, 1979

By Alexander May

In its role of providing technology to promote the efficient use of minerals and mineral process waste, the U.S. Bureau of Mines has conducted research at: its Tuscaloosa Research Center to identify and develop high volume uses for phosphogypsum. Mixtures containing a maximum of 50 percent phosphogypsum, 6 to 10 percent lime, and the remainder fly ash had compressive strengths as high as 4,800 psi. The effects of the mounts of phosphogypsum, lime, and fly ash were investigated. Also, the effects of fly ash to lime ratios were studied.

Jan 1, 1983

By John D. Lupton

This paper will discuss the benefits and advantages of using 3D survey data in stope analysis. Obtaining detailed 3D survey data of underground mine progress and production is a challenge. It is almost impossible to ?see? around corners, underneath overhangs, or deep into dark, dusty, humid underground voids. Thus, valuable ore can remain permanently encased in backfill. Without the benefit of 3D survey data, underground mines have the difficult task of meeting grade quotas without the benefit of knowing exactly what has been mined. Lack of this data usually results in unfavorable month end Reconciliation factors, where grades must be adjusted to match grades assessed by the Mill.

Apr 1, 2005

By Paul Hatmaker

"The Bureau of Mines recently has issued a general information circular covering briefly the origin and occurrence, properties, uses, exploitation, and marketing of diatomite. Since this publication was prepared, additional information has become available regarding one of the newer uses of diatomite — that as a filler in battery boxes. As this market is rapidly becoming one of the important outlets, a brief discussion of such use may be of interest.Diatomite is a mineral substance composed principally of the skeletal remains of diatoms. The skeletons of these microscopic flowerless water plants are made from silica present in the water in which these tiny plants live. The minute shells or ""casts"" accumu¬late in the bottom of lakes, ponds, or inland seas, and eventually become more or less consolidated into beds of diatomite.The uses of diatomite depend largely upon its peculiar properties. Diatomite is a highly porous substance and possesses marked absorptive powers. The large percentage of pore space makes the material very light in weight. It is relatively insoluble in most solutions.The largest deposits in the world are found in California, but diatomite occurs in many other Western States and also is found in a number of places along the Atlantic seaboard. Outside of the United States diatomite occurs in many countries; Algeria and Germany are among the largest producers.Usually diatomite is mined either by underground or open—cut methods. In some instances it may be dredged from lake and swamp bottoms. It must be dried prior to grinding or other preparation for market, and for many purposes must undergo a complex sizing and grading system for removal of such impurities as sand and clay and for classification of the material to the various sizes desired,"

Mar 1, 1931

By P Klaric, N Swart, S Barnes

The recent advances in digital imaging technology, specifically around photogrammetry, have facilitated precision measurement in the difficult conditions encountered in an underground development mining environment. With the recent downturn in the resources industry, many mining houses have begun to focus on cost reduction projects and driving efficiencies. The application of digital photogrammetry has allowed greater insight into the development mining cycle and supported a focus on areas where efficiencies and cost savings can be achieved. Data collation, via digital image capture, can be completed with minimal disruption to the development mining cycle with analyses taking a nominal time to process and interpret. The result can be a stark visual representation of the result of blasting and associated activities of the development mining cycle. Many millions of dollars of benefit can be derived from understanding the impact of each component of the development mining process, with some of the biggest savings associated with conformance to drill design and the minimisation of overbreak during blasting. This paper will explain the image capture process, analyses and instigated improvement opportunities that were undertaken at a number of mine sites to improve efficiencies and drive savings in their development mining processes.CITATION:Klaric, P, Swart, N and Barnes, S, 2017. Digital imaging provides valuable insights into underground development mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Samuel Filgueiras Rodrigues, Clodualdo Aranas Jr., Gedeon Silva Reis, Eden Santos Silva, Fulvio Siciliano

When austenite is deformed above the Ae3 temperature, partial amount of it transforms dynamically into ferrite by a displacive mechanism. After unloading, it retransforms back into the stable austenite by a diffusional process. This influences the rolling load which decreases under isothermal condition or does not increase with decreasing temperature as rapidly as expected under cooling. Plate rolling simulations under isothermal and continuous cooling conditions were carried out on a 0.09 wt.% Nb X-70 steel. Pass strains of 0.2 were employed together with interpass times of 10 s, and 30 s for the cooling conditions and 0.3 with interval of 10 s at 900 °C for the isothermal experiments; strain rate of 1 s-1 was used during the simulations. The mean-flow-stress (MFS`s) behavior of both conditions indicates that dynamic transformation and dynamic recrystallization were taking place during straining. The critical strains for the initiation of dynamic transformation fell around 0.06 while the critical strain for DRX was 0.12. It has been shown that ferrite is formed due to the applied deformation of roughing passes and increases its volume fraction throughout the finishing rolling stage. Under cooling conditions, the ferrite formation is also favored as the temperature approaches the Ae3 line. Such ferrite forms when the driving force for dynamic transformation is higher than the total free energy barrier preventing its formation. This obstacle consists of the free energy difference between austenite and ferrite as well as the lattice dilatation work and shear accommodation work. The addition of Nb retards the retransformation of the ferrite into austenite. Moreover, holding times after rolling increases the amount of austenite available for microstructure control on subsequent stages. The dynamic transformation (DT) mechanism can be used to design improved rolling schedules

Oct 1, 2019

By Lawson F

Narrowly sized samples of synthetic chalcocite (Cu2S) and covellite (CuS) were leached in oxygenated acidic sulphate-chloride solutions. Chalcocite leaches via a two-stage process, the first stage being much more rapid than the second. The apparent activation energies are 42.7 kJ/mol and 68.2 kJ/mol respectively, indicating that both stages are controlled by surface chemical reactions. The leaching of covellite is also chemically rate limited with an apparent activation energy of 77.0 kJ/mol. The shrinking core model is able to be used to describe the leaching processes of both copper sulphides. Over 97% of copper present in chalcocite dissolved in 0.5 M H2SO4i0.5 M NaCl solution under one atmosphere pressure of oxygen at 85¦C in three hours from particles 36 pm in diameter while only 85% of the contained copper in covellite particles 13 pm in diameter dissolved in the same solution under the same pressure at 90¦C in six hours. About 99% of the sulphide sulphur in chalcocite was oxidised to elemental sulphur while only 90% of sulphide sulphur was converted to elemental sulphur during covellite leaching. The mechanism proposed for the two-stage leaching of chalcocite particles is as follows: in the first stage, cuprous ions rapidly diffuse to the external reaction surface where they lose electrons and go into solution as a complex cupric chloride ion CuCl'. The second leaching stage begins when covellite is formed at the external surface. Copper again goes into solution as the CuCl* ion. The mechanism for leaching synthetic covellite is similar to the second leaching stage for chalcocite except that the leaching rate of synthetic covellite is substantially lower than that of the newly formed 'covellite'. Elemental sulphur formed on the particle surface retards the dissolution processes during both chalcocite and covellite leaching. The presence of chloride ions is necessary if essentially all of the copper from chalcocite is to go into solution. When no chloride ions were present, the leaching rate of both newly formed and synthetic covellite was almost zero. The main role of chloride ions in both chalcocite and covellite leaching appears to be to disrupt the passivation film of sulphur on the particle surface.

Jan 1, 1989

By Arcy R., D&apos George

The Bureau of Mines has developed, on a laboratory scale, a superior Eluex-type circuit for eluting and recovering uranium from ion exchange resins. The improved circuit differs from conventional Eluex practice in that a stage of uranium solvent extraction is coupled with each stage of resin elution rather than the elution and solvent extraction operations being conducted separately. The new system reduces the number of stages, retention time, and resin inventory in the elution circuit to one-fourth or one-fifth that in existing circuits. The system is applicable to both resin-in-pulp and moving-bed-type ion exchange uranium recovery circuits.

Jan 1, 1969

Based upon specialised experience of rope mechanics spanning over 20 years, this paper reviews the processes of degradation and fatigue that are relevant to hoisting ropes in mines. The review is brought up to date with an account of the most recent work in this field, which identifies a torsional fatigue process and quantifies the impact of degradation upon the residual service life. A proper understanding of these processes is important in determining how different parameters of hoist design and operation interact to determine rope life. This knowledge is also important in informing decisions relating to rope discard based upon observed condition, as well is identifying the critical features that must be quantified reliably during inspection.

Jan 1, 2005