Search Documents

By Ross A. Scarano

It wasn't until late 1976 that the U. S. Nuclear Regulatory Commission (NRC) set about to address the uranium tailings issue in earnest. It was decided that a generic environmental impact statement related to uranium milling operations would be prepared to support formal tailings regulation. We recognized, however, that this was a task that would take many years to complete and we could not take a "business as usual" approach to tailings management in the interim; the issue was too sensitive. To facilitate licensing during the interim period, the NRC developed guidelines in May 1977, for the industry in the form of the following performance objectives for tailings management: Siting and Design 1. Locate the tailings isolation area remote from people such that population exposures would be reduced to the maximum extent reasonably achievable. 2. Locate the tailings isolation area such that disruption and dispersion by natural forces is eliminated or reduced to the maximum extent reasonably achievable. 3. Design the isolation area such that seepage of toxic materials into the groundwater system would be eliminated or reduced to the maximum extent reasonably achievable. During Operations 4. Eliminate the blowing of tailings to unrestricted areas during normal operating conditions. Post Reclamation 5. Reduce direct gamma radiation from the impoundment area to essentially background. 6. Reduce the radon emanation rate from the impoundment area to about twice the emanation rate in the surrounding environs. 7. Eliminate the need for an ongoing monitoring and maintenance program following successful reclamation plan. 8. Provide surety arrangements to assure that sufficient funds are available to complete the full reclamation plan.

Jan 1, 1980

By Wayne I. van Drunick

"Energy balance modeling has recently been shown to be a competent tool in the estimation of SAG mill discharge rheology. Work performed by van Drunick and Moys (2001) validated the ability of an energybalance filter to estimate the slurry density from an operating SAG mill. The importance of rheological data is highlighted by several authors who show the effects on load behaviour and thus mill performance. Energy balance models were developed to account for the dynamic energies in the mill discharge sump. The models then made it possible to infer the mill discharge density. A sampling campaign was performed and the errors from the sump energy balance were within tolerable limits.Since the initial results were published, it has been decided to further develop the modeling techniques in order to focus on balancing the energies around the entire mill. The critical measurements for the energy balance will be the temperatures of all the streams entering and leaving the mill, including energy losses to the environment. Metso’s OCS© (Optimising Control System) currently controls the 3 SAG mills at Anglogold’s Mponeng Gold Plant (South Africa). The OCS has built-in Kalman filtering tools to effectively handle variances and noise in the models and the mill circuit data respectively. The new models are therefore constructed in the OCS platform, and will be run in parallel with Metso’s current modeling and filtering systems. The work is a collaborative effort between Anglogold, the University of the Witwatersrand and Metso. The benefits of energy modeling, compared to mass modeling, are that energy data are more accurately measurable than mass data. The inferred mill parameters can therefore be improved provided that a competent set of models is produced to process the (accurate) thermal measurements."

Jan 1, 2003

By Max W. Ball

THE geologist or mining engineer, whose work takes him into the western United States, whether for the Government or private enterprises, is likely to be called upon to classify public lands as to their mineral character, or to review such classification already made, usually by a Government geologist or mineral inspector. The public-land law covering the matter is clear and logical, and a knowledge of its simpler principles is necessary to intelligent classification work. There are two classes of cases in which a classification of lands as mineral or non-mineral may be required: .first, cases in which lands classified as mineral will be retained by the Government and lands classified as non-mineral alienated; second, cases in which lands classified as mineral will be alienated and lands classified as non-mineral retained.

Jan 1, 1921

By D. Harrington

WHEN the word gas is mentioned in connection with mining, almost invariably it is inferred that the explosive gas, methane, is in mind and that it must refer to coal mining. While it is true that methane occurs, or is likely to occur, in almost any or all coal mines, it is also a fact that the metal mines of the world have in them by far a greater variety of gases than have the coal mines. In many cases the gases in metal mines are as dangerous to individuals as the gases likely to be found in coal mines; in some instances the metal mine gases are even more deadly. The coal mine is more likely to have methane than the metal mine, in rare instances it may have high percentages of nitrogen or high carbon dioxide, or there may be a deficiency of oxygen where the air is confined in a blind end or in a sealed region; much more rarely there are found in coal mines in relatively small percentages, ethane, or other hydrocarbons with odor of ether, gasoline or kerosene, or there may be minute percentages of hydrogen sulfide. In time of coal mine fire or explosion, there is likely to be high carbon monoxide (4 per cent. or over in some cases) and if the coal contains much sulfur, there may be some sulfur dioxide in the fire fumes. In metal mines there are a number of cases of occurrence of methane and attendant explosions; some metal mines have appreciable percentages of the decidedly explosive hydrogen; in some metal-mining regions carbon dioxide flows into the mine, fills the workings and overflows just like water. In other regions, at many working faces there are high-temperature gases containing a mixture of gases of sulfur (sulfur dioxide, hydrogen sulfide and possibly SO3 in some cases) together with carbon dioxide and nitrogen, and the deadly hydrogen sulfide in lethal proportions is found in some high-sulfide metal mines at blasting time. Carbon monoxide constitutes a decidedly dangerous day by day hazard in connection with metal-mine blasting, because of the heavy charges of dynamite that are used and the use of fuse, which in burning gives off much carbon monoxide. The poisonous gas hazard is accentuated because of the relatively small openings where metal-mine blasting is done and to the inefficient ventilation of the usual metal mine.

Jan 1, 1930

By Lyman Johnson

Single crystals qf copper in "single slip" orientatiorzs have been deformed in compression. During defortnation all of the independent deformation parameters have been measured. These parameters consist of thefive strain components and three components descrihing the lattice rotation. By a finite strain analysis these pararmeters , forrming a deformation gradient martrix, are related to the amounts of slip on each of the twelve slip systems. The results show that the amount of secondary slip is about equal to the amount of primary slip. This is an order of magnitude larger than has been believed previoutsly. ACCORDING to early theory and experiments, when a single crystal of a fcc metal is deformed in tension or compression it should deform by slip on only one slip system until the stress axis reaches a symmetrical orientation.' However. the observation of a large increase in the secondary dislocation density during ..single slip" makes it clear that some slip does occur on secondary systems. Knowledge of the amount and distribution of this secondary slip is essential to a complete understanding of the mechanisms of single-crystal deformation. Ahlers and Haasen 2 and Mitchell and Thornton1 have tried to detect the amount of secondary slip in single crystals of silver and copper, respectively. Each simultaneously measured the angle A, between the tensile axis and the primary slip direction and the length 1 of a gage section of the specimen after incremental amounts of deformation in tension. The measured A, was then compared with the theoretical single slip angle hp. given by sin Ap = j sin . hO where ?o was the initial angle between the tensile axis and the primary slip direction and lo was the initial gage length. In both sets of experiments a small but systematic difference between ?e and ?p was found. This difference must be due to the occurrence of secondary slip. However, as Mitchell and Thornton1 pointed out. nothing quantitative can be said about the amount and distribution of this secondary slip from the measurements that they made. The reason that no quantitative conclusions could be made is because no unique solution for the distribution of slip on the twelve fcc slip systems can be determined from only two measured deformation parameters such as A and 1. There are, in fact, eight independent macroscopic deformation parameters that can be measured when a single crystal undergoes a homogeneous deformation. Physically these can be thought of as the five finite strain components and the three angles describing the crystal lattice rotation. All eight of these parameters were measured by Taylor4,5 for aluminum deformed in tension and compression. At that time the concern was to show that slip occurs on {111 (110) systems in fcc metals, and the mathematics were not available to determine what slip distributions were compatible with the measurements. In this paper the mathematics6,7 are developed that allow the slip distribution to be determined from these measurable macroscopic deformation parameters. The analysis is applied to the measurements of the strain and lattice rotation of copper single crystals deformed in compression. The results show that the amount of secondary slip is an order of magnitude larger than had previously been thought. CRYSTALLOGRAPHIC DESCRIPTION OF A HOMOGENEOUS DEFORMATION The deformation of a solid body can be represented by a transformation matrix F that transforms the un-deformed state into the deformed state. Consider a vector X connecting two material points in the unde-formed material and the vector x connecting the same two material points after deformation, where both vectors are referred to the same set of Cartesian axes. The final vector x is related to the initial vector X by the equation: X = FS. [2] Eq. [2] can be considered as the equation defining F, which is called the deformation gradient matrix. Its components are: If the deformation is homogeneous, the transformation is linear and the components of F are constants. Using subscript notation, if P is the unit vector in the initial direction of a material line, the components of the unit vector p in the direction of the same material line after deformation are given by:

Jan 1, 1970

By Claudio Cesar da Costar

O Alto Forno 1 da ArcelorMittal Tubarão, operou entre 30 de novembro de 1983 e 18 de abril de 2012, produzindo 93.915 Mt. Durante esta campanha, inúmeras melhorias foram implementadas para aumentar sua longevidade mantendo o volume e custo de produção. O Alto Forno 1 da AMT é reconhecido como recordista tanto em volume de produção quanto em tempo de operação para uma única campanha. Durante sua reforma, foram empregadas as técnicas de reforma em grandes blocos, as quais foram trocados todo o cadinho, corpo e topo do Alto Forno, trazendo recursos tecnológicos possibilitando obter melhores resultados durante a segunda campanha. Após a reforma, o Alto Forno 1 continua apresentando bons resultados em termos de produtividade, consumo de combustíveis e índices de trabalho, colocando-o entre um dos Altos Fornos com melhores resultados do grupo ArcelorMittal.

Aug 16, 2017

The fracture behavior of second phase particles and the role of matrix material on the wear resistances of the three Al-Si alloys containing 8, 17, and 19% Si were investigated using single pass scratch testing technique by applying normal loads between 0,15 and 5,00 N, in ambient air, Optical microscopy and SEM with EDS were used to analyze microstructures and morphologies of scratch tracks of the Al-Si alloys, The results showed that needle-like Si particles fractured under a load of 0.50 N, while block-like Si particles fractured at loads above 3,00 N, The Al-17% Si alloy with large number of needle-like particles (area fraction 16,4%) exhibited the highest coefficient of friction (0,8) and the widest scratch track, The Al-19%Si alloy containing high Si percentage and larger number of block-like particles (area fraction 16%) exhibited the lowest coefficient of friction (0,37) and the narrowest scratch track width. Presence of block-like particles was effective in reducing the amount of material transfer from Al-Si alloy surfaces to the counterface.

Jan 1, 2005

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By W. D. Robertson, Raymond C. Boettner

A study was made of the change in density during the first (transient) and second (linear) stages of the creep curve of polycrystalline copper as a function of 1) stress, 2) temperature, 3) plastic strain, 4) impurity and atmosphere effects, and 5) structure, including single crystals. Voids were not observed in single crystals strained 15 pct at 500°C, or in a polycrystal-line aggregate produced by recrystallizing a single crystal, within the limit of sensitivity, Ae/e = 1 x 10-4. It appears that voids are heterogeneously nucleated at grain boundaries by an insoluble phase, or phases, which can be removed by directional solidification. The principal controlling mechanism of void growth appears to be condensation of vacancies at grain boundaries. Vacancies are transported to a boundary and condense as a consequence of the tensile stress component across the boundary, which depends on the orientation and configuration of the boundary plane and on boundary shear across ledges and other irregularities. The ultimate source of vacancies is the free surface and diffusional transport is by way of the boundary plane. PREVIOUS investigations have dealt with the nucle-ation of voids at grain boundaries under creep condition~'-~ and with the connection between grain boundary voids and subsequent brittle fracture.5-7 Growth of voids during the creep process, particularly in the transient and linear stages of creep, has not been studied with the same intensity. Therefore, it seems pertinent to investigate the process of void growth with respect to the related creep curve, and the morphology of growing voids with respect to the structure.

Jan 1, 1962

By Norman Schapiro

Future ore bodies will, most likely, be more costly to find, mine and process than those now in production because most of them will be of lower grade or found deeper. To evaluate an ore deposit for extraction of metal values it is important to select the optimum economic process from among the many available options. The physical and chemical behavior of the minerals present should govern the process selection. Process mineralogy which combines mineralogy and petrography with process development engineering generates the data on mineralogy, composition and texture of gangue and valuable minerals from which the optimum process steps can be selected in the commercial design of the ore processing plant. These insights also help in solving operating problems caused by changes in the ore body

Jan 1, 1981

By I. N. Zavarine

AUSTENITE is often defined as a solid solution of carbon or carbide in a nonmagnetic form of iron. Conversely, magnetic measurements are often used by investigators for the purpose of detecting the degree of austenite decomposition after an iron alloy has been subjected to certain thermal or mechanical treatments. Association of the magnetic state with the gamma-phase decomposition is often extended to the alloys of iron with elements other than carbon. Definition of austenite as a nonmagnetic solid solution cannot be accepted in the light of available information without certain reservations. The relation of magnetic transformations with the gamma-phase decomposition in the complex alloys of iron has never been rigorously proved. The present investigation deals primarily with the magnetic trans-formation that occurs in carbon steels during the quenching process. The work was further limited to a study of magnetic transformation in carbon steels quenched at such rates as are necessary to retain the product of austenite decomposition in a martensitic state.

Jan 1, 1934

By White A. H, Gillies A. D S

In recent years the Australian gold industry has gone through a major expansion phase. The need for finance has led to adoption of different approaches such as the well known gold loan, forward selling, equity participation by suppliers and equipment leasing. During early periods of the expansion, significant new equity was raised chiefly for high risk exploration ventures. The major form of new equity finance was ordinary shares, often in 'No Liability' companies. The increasing capital requirement of the huge new development projects of the 1980s also spurred the use of debt finance. This trend was accelerated as high inflation and the taxation advantages of debt finance made borrowing attractive. This paper reviews major financing techniques used by the Australian gold industry with particular emphasis on the innovative financing techniques initiated recently. An analysis has been undertaken of the effects on the industry of issues such gold loans, forward selling, equity participation by suppliers, fly-in fly-out operations, contractor mining and equipment leasing. In order to achieve a better understanding of the innovative financing techniques, a survey of already published financial data from well known Australian gold mines was carried out. Data was collected from various published financial reports of gold mining companies. In addition, a questionnaire survey was sent to gold mining companies to assist the collection of further information. The results of this study show that there are a significant number of gold mines variously using gold loans, forward sales, contractor mining and fly-in and fly-out arrangements to finance their projects. Only four operations have vendor suppliers investing capital funds in their projects. Based on the findings of this study, conclusions and recommendations are drawn that these approaches are likely to be with Australian gold industry for some time in the future and will continue to be intensively applied to finance gold projects.

Jan 1, 1994

By M. Imazu, Ö. Aydan

"A new rock classification, Rock Mass Quality Rating (RMQR) proposed by the authors is briefly explained and its application for the design of tunnels and large underground openings support systems is described in this paper. RMQR is an index to evaluate the state of rock mass. The preliminary support design may be based on the concept to prevent structurally controlled failures of rock mass. RMQR can also evaluate the yielding characteristics of rock masses so that it is possible to design a support system to prevent or control the deformation of surrounding rock through the utilization of the proposed rock mass classification and some analytical and numerical techniques.INTRODUCTIONThe first three authors proposed a new rock classification system named Rock Mass Quality Rating (RMQR) (Aydan et al. 2014). RMQR quantifies the rock mass state, and using the classification system together with intrinsic geo-mechanical properties of intact rock, possible geo-mechanical properties of rock masses can be estimated. The instability modes of underground openings can be structurally controlled because of the orientation of discontinuities in rock mass and the in-situ stress induced (Aydan 1989; Aydan et al. 1993, 1996; Aydan and Genis, 2010). The authors (Aydan and Ulusay, 2013; Aydan, 2016) have also tried to apply this system to the design of a tunnel support system. The authors presented initial guidelines for the RMQR classification system earlier (Aydan and Ulusay, 2013).In this paper, the authors provide further guidelines and establish some criteria for support system design that considers loading conditions and types of underground structure according to RMQR. Guidelines are alsos proposed for selecting the proper size of rockbolts, rock anchors, shotcrete, steel ribs and concrete liner. These guidelines are based on past experiences with various underground structures, theoretical understanding and the anticipated behavior of rock mass under given in-situ stress conditions and excavation techniques. The authors also utilized some databases developed for large underground caverns and tunnels excavated in squeezing or rock-bursting ground conditions."

Jan 1, 2016

By H. W. Glen

The National Institute for Metallurgy - usually referred to as NIM - has become the Council for Mineral Technology, or Mintek. The Honourable F. W. de Klerk, Minister of Mineral and Energy Affairs, announced the change of name at the official opening of the main entrance to Mintek's premises on 30th October, 1981. Awards for bravery Two men who disregarded the dangers of fiercely burning timber and falling rocks to douse an underground fire, using their hard hats to scoop water from a drain, received the Chamber of Mines Award for bravery at a ceremony held at West Driefontein Gold Mine near the end of October.

Jan 1, 1981

By M. Howard Berliner

During the spring of 1944, the Bureau of Mines investigated the Crescent mine area near the village of Rewey, Iowa County, Wis., as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the Nation's war program. The Bureau of Mines completed 24 churn-drill holes in an area immediately to the west of a mineralized section which had been mined through shallow workings for lead and zinc more than 40 years earlier.

Jan 1, 1948

By E. P. Peleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed Pressure, see Fig. 2. The

Jan 1, 1953

By E. P. Peleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed Pressure, see Fig. 2. The

Jan 1, 1953

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By C. D. Woodward

PRIOR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but. they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that are not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 7 ½ ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.), and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of ,the stations, however, is about 75° F. (24° C.), while the average temperature in some of the drifts and crosscuts is 92° F. (33.5° C.).

Jan 2, 1922