Search Documents

By Xavier Pita, Alexandre Pinto, António Cristovão, Rui Tomásio

"The cutter soil mixing technology was been applied in Portugal since the last seven years. The aim of this paper is to present the main design and execution criteria, related with both the cofferdam and foundations solutions, using soil-cement panels, reinforced with steel profiles, at the new Leixões Cruise Terminal, located at the Leixões Port, in Portugal. The Terminal building was built with one basement on a marine environment, over very difficult geological and geotechnical conditions, which demanded the use of some unusual and integrated geotechnical solutions. It is also pointed out the importance of the QC/QA, as well as the technical, economic and environmental advantages of the cutter soil mixing technique, comparing with same more conventional solutions.1 INTRODUCTIONThe construction of the new Cruise Terminal at Leixões, main gate of the Atlantic Ocean to the North of Portugal and Spain, as a consequence to the constant increase of the cruise traffic, was a challenge from both the geotechnical and structural point of views, mainly due to very difficult and unusual conditions, ranging from the geological and geotechnical scenario to the existent and under operation Leixões Port infrastructures, mainly the South break water, as well as the existent cruising boarding deck (Figure 1).According to the Terminal Project it was necessary to build one basement below the water table level, including several earth retaining structures in order to allow the excavation works on dry conditions leading to a global cofferdam effect. For this purpose soil - cement panels, using CSM technology, reinforced with steel profiles, micropiles (both for foundation and cut off effect) and the existent sheet piles were used. Also pointed out are the adopted special foundations of a very complex structure, including bored piles and micropiles (Figure 1)."

Jan 1, 2015

By Hall T. P, Taylor R. N

Fluid flow in a 1:14 scale water model of the shaft and settler of the Kalgoorlie Nickel flash smelter has been investigated by flow visualisation and numerical modelling. Detailed flow fields through the reaction shaft, settling chamber and uptake are presented for flow rates up to 800 Vm and a number of burner configurations. The predicted flow fields were compared with experimental data obtained from streak photographs and video recordings. The effects of cessation of flow through individual burners and changes in shaft dimensions were also Investigated.

Jan 1, 1992

By Steve Wiig

In 1987, the Rock Springs, WY district office of the US Bureau of Land Management (BLM) began to develop an automated system to store, maintain and manipulate more than 14,000 drill hole logs contained in the district's office files for various solid leasable minerals. The development of this system was based predominantly on a trial-and-error basis, with many procedural changes incorporated over time. The current Automated Drill Hole Database and Analysis System will continue to evolve with new software developments and increased personal expertise in this field. The mission of the BLM's Branch of Solid Minerals is mandated by a series of federal laws. The most important are The Mineral Leasing Act, the Federal Land Policy and Management Act, the Federal Coal Lease Amendments Act and the Surface Mining Control and Reclamation Act. Several regulations, promulgated from these laws, dictate that BLM must perform certain tasks and functions as part of its specific duties. The regulations that apply to the BLM Solid Minerals program are codified at 43 Code of Federal Regulations (CFR) 3400 for coal, and at 43 CFR 3500 for non-energy solid leasable minerals, such as sodium, phosphate and potash. Specific functions required of the Branch of Solid Minerals necessitates the use of geologic and drill hole data analyses. These functions can be divided into pre-lease and post-lease. Examples of pre-lease functions that normally require some level of drill hole data analyses include:

Jan 1, 1992

By Wang Xuguang, Zhang Xiaozhi, Li Guozhong, Xiong Daiyu

The emulsion explosive is a new kind of water-based industrial explosives that was developed at the end of 1960s. In the 1970s, BGRIMM invented EL-series emulsion explosive that created a new era of water-based industrial explosives technology and products in China. From single type to varieties, the perfect BGRIMM emulsion explosives technology has been formed, which consists of 9 series, over 30 types explosives and related production equipments and processes such as cap-sensitive rock emulsion explosive, opencast emulsion explosive, coal permitted emulsion explosives, low-temperature-resistant emulsion explosive, high-temperature-resistant emulsion explosive, high power emulsion explosive, bulk emulsion explosive for loading truck and powder emulsion explosive. From the early 1990s, BGRIMM successfully developed opencast emulsion explosives and the computer controlled continuous production line of small-diameter cap-sensitive emulsion explosive which raised emulsion explosive production technology of our country to a new lever. With the successful development of powder emulsion explosive and related computer controlled continuous production line, on-site mixed emulsion explosive and loading truck as well, the category of industrial explosives is getting more complete and reasonable. This paper pres ents the history, achievement and development of BGRIMM emulsion explosive technology, also forecasts the future of linked technology.

Jan 1, 2003

By James S. Browning

The Bureau of Mines conducted laboratory and small--scale continuous tests of weathered mica pegmatite ores from Hart County, Ga., to determine the technical feasibility of recovering commercial-grade mica concentrates by flotation. Two modifications of the Bureau-developed anionic-cationic method were used. In one method, sodium carbonate and calcium lignin sulfonate were used for pH control and quartz depression; this method yielded mica concentrates containing 98.5 percent mica with a recovery of 91.4 percent. In the other modification, lime and sodium silicate were used with the calcium lignin sulfonate; concentrates containing 98.9 percent mica with a recovery of 86 percent were obtained.

Jan 1, 1966

By B Murphy, J van Zyl, G Domingo

In a narrow vein mining scenario, employing preconcentration technology underground not only results in reduced transport and handling costs but may allow alternative mining methods to be implemented, improving overall productivity. Using processing technology underground is not a new concept with underground crushing and screening operations being quite widely utilised. With advances in processing technology over recent years, there are now a number of robust processing methodologies in existence that are capable of performing separation of ore and waste at a relatively coarse size. Many of these technologies are readily adaptable to the underground environment and if employed could result in a number of cost and productivity benefits.Assessment of the oreÆs suitability for preconcentration technology is the first step in harnessing these potential savings. This paper discusses how coarse ore sorting and gravity separation could be employed underground in a narrow-vein scenario and details the test work that is required at the front-end of a project to see if this potential exists.CITATION:Murphy, B, van Zyl, J and Domingo, G, 2012. Underground preconcentration by ore sorting and coarse gravity separation, in Proceedings Narrow Vein Mining 2012 , pp 237-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By J. R. Lucas, H. E. Rutherford

The primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this study was to determine experimentally the elastic wnstants of various rock specimens with the use of ultrasonic equipment. Elastic constants can definitely be determined quickly and accurately by ultrasonic investigation. With proper equipment there are indications that ultrasonic waves could be utilized in the detection of flaws, such as fractures and planes of weakness, measurement of thickness, and the study of structure of rock material. Ultrasonic principles have been applied in many industries for the purpose of determining the structural characteristics of various materials. The principal applications of interest here are detecting flaws, measuring thicknesses, and determining elastic constants. The main advantage of ultrasonic analysis is that it is nondestructive. It also has extreme sensitivity, high penetrability, good accuracy, rapid response, and the necessity to have access to only one side of the specimen. These various applications and advantages lead one to think that ultrasonic principles might be applied to rock material in situ for purposes of analyzing its structural characteristics. Therefore, the primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this research was to determine experimentally the elastic constants of various rock specimens with the use of ultrasonic equipment. The term ultrasonics is given to that branch of acoustics dealing with periodic sounds whose fre- quencies are above the audible range or above approximately 15,.000 to 20,000 cps. The first practical production of this high frequency sound was made possible after World War I due to developments of electronically controlled sound wave sources. At the present, the maximum practically attainable ultrasonic frequency is approximately 1000 megacycles per sec. Sound waves of sufficiently high frequency can be made to travel in a beam with little spreading. Therefore, such a beam can explore a material and detect nonhomogeneities in it by reflection. This is the principle of the ultrasonic reflectoscope invented by F. A. Firestone' in 1942. An ultrasonic beam, on pulse-penetratink a solid material medium, produces an echo when it strikes a flaw which has different acoustical properties than the surrounding medium. This echo can be detected by the same transducer which sends out the original pulse. This principle is the basis of the important industrial techniques of nondestructive ultrasonic testing of metals and other solid material. Later developments in the field of ultrasonic testing of solid material have been mostly improvements in equipment and instrumentation. To date, most of the industrial applications of ultrasonic analysis of solid bodies have been in the aircraft, electrical, and nuclear energy fields on the nondestructive testing of metal. The one solid material similar somewhat to rock material, upon which some work has been done to apply ultrasonic testing techniques to study structural integrity, is concrete. Jones and Gatfield3 briefly summarize this work on concrete. Their basic conclusion was that the strength of concrete was a function of the change of the longitudinal sound wave velocity in the concrete. Only recently has any extensive study been made to apply ultrasonic testing techniques to rock material. Lutsch studied rock material by an ultrasonic pulse method to determine the extent and degree of fracture of rock faces. Lutsch states that the number of observed reflections is a measure of the degree of fracture and that only ultrasonic waves are able to detect fractured zones subjected to high pressure. Suzuki, Sasaki, and Siohara5 studied the characteristics of the sonic wave in rock for propagation over a wide range of wave lengths. They indicated that, in rock, the propagation constant and attenuation of the

Jan 1, 1962

By W. J. Wrazej

THE measurements on the formation of multi-layered scales on pure iron1 and the metal -lographic examination of the produced layer of FeO, Fe,O,, and Fe2O3 shown in micrographs2 throw much interesting light on this apparently well-known subject. Professor Paidassi announced2 that in a few months7 time further results are going to be published with regard to the growth of Fe2O3 and Fe2O3 layers on an Armco iron as a function of temperature. Because of the very thin layers of Fe2O3 which are shown by Paidassi (Fig. 10 of ref. 2) when samples were scaled in air at 700°C for 4 hr and because this is not in agreement with the present author's previous observations, the following experiment was recently carried out. Polished cylindrical samples 13/64 in. in diam and 1/4 in. long from electrolytic iron used for spectro-graphic work (Hilger, H.S. Iron rods, F.693) and an Armco iron sample 1/4 in. in diam of the same length were suspended in a muffle furnace on Nichrome wire and annealed in air for 4 hr at 700°C 5OC. Because of the known easy peeling off of the Fe2O3 layer which is mainly in the form of powder (purple red dust on the surface) the samples were protected against any draft and shock. After annealing, the samples were cooled in air and placed in the mount-

Jan 1, 1954

By Samuel M. Bryant

The purpose of this study was to develop procedures to measure Bingham flow properties for mine tailings and to use these to predict the possible consequences of a hypothetical tailings flow failure at the Tenmile Tailings Pond at Climax, Colorado. The consequences of such a failure were found to be minimal, and the failure itself highly; unlikely. Values of Ty (Bingham yield shear strength) and np (plastic viscosity) were measured for 10 materials using results obtained from vaned coaxial viscometer tests and triaxial tests.

Jan 1, 1983

By Nicholas J. Grant, Hanna Ibach, Bill C. Giessen

The system Ta-Rh was investigated over the entire comnposition range using metallogvaphic and X-ray techniques as well as thermal analysis. Terminal solubility limits, solidus temperatures, and the crystal structures of two new intermediate phases were determined. There are five intermediate phases: o, tetragonal, isostructural with o(Fe-Cr); a1, orthorhomnbic : a2, orthorhombic, isostructural with CozSi; 0 3, a high -temperature phase of unknozun structure; and a TaRh3, cubic, AuCu3 structure. a, aL, a,, and a melt peritectically; and a TaRh, has a maximum melting point. Five peritectic and one eutectic reactions occur. THE Ta-Rh phase diagram has not been fully treated in the literature; however, two inter metallic phases have been described.&apos;-&apos; This study attempts to work out the diagram covering the details of phase boundaries as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by National Research Corp., Cambridge, Mass., and rhodium powder of 99.9 pct purity, supplied by Bishop Co., Malvern, Pa. Analyses as given by the manufacturers are presented in Table I. In addition to the spectroscopic analysis, an oxygen analysis has been made of the tantalum powder. After preliminary trials, the standard procedure employed in making the alloys was as follows (see Ref. 4 for further details). The powders were weighed, mixed manually, compacted under 16,000 psi, and arc-melted at not more than 500 amp under thoroughly titanium gettered welding-grade argon of 400 mm Hg pressure. The gettering process was repeated after each melt. It had been shown previously5 that under these conditions no oxygen pick-up exceeding 0.001 pct in a hafnium button could be detected. The buttons, ranging from 5 to 10 g in weight, were inverted or, if possible, crushed and remelted three times. Melting presented no difficulty, except for tantalum-rich al- loys, which showed considerable spashing during melting. The average weight loss of 1 wt pct rose to 2.5 wt pct in these cases. Subsequent melting, however, resulted in losses of less than 0.1 wt pct. The melts obtained frequently showed small in-homogeneities, mostly in the tantalum-rich part of the system below 25 at. pct Rh. This was not due to insufficient blending of the elements, but to crystallization taking place from the cooled bottom. This condition was not improved by further re-melting; therefore the following precautions were taken. Cross sections of as-cast buttons were made. For the investigation only buttons were used where these inhomogeneities did not exceed 1 at. pct (estimated from the amounts of haSeS resent). In addition, only the center portions of such buttdns were utilized to minimize errors. Smaller buttons showed smaller concentration gradients and were used as a check. Finally, all alloys were homogenized to eliminate coring (see below). After this, the error in alloy composition due to inhomogeneity was cl at. pct. In order to confirm the concentrations of the alloys and to provide an impurity check, wet-chemical analyses and oxygen-fusion analyses of four key alloys were carried out. The results, together with the concentrations as calculated with the weight balance method, are presented in Table 11. It was found that for three alloys the agreement is very good (< 0.2

Jan 1, 1964

Lawrence Addicks, Perth Amboy, N. J. (communication to the Secretary*): The excellent series of photo-micrographs given in this paper shows clearly the relation between micro-structure and cuprous oxide in refined copper. The authors suggest that this method of examillation might be substituted for the " button " method now used to control the refining of cop

Jan 1, 1904

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By A. G. Weber, K. H. Coats, M. H. Terhune, R. L. Nielsen

Two computer-oriented techniques for simulating the three-dimensional flow behavior of two fluid phases in petroleum reservoirs were developed. Under the first technique the flow equations are solved to model three-dimensional flow in a reservoir. The second technique was developed for modeling flow in three-dimensional media that have sufficiently high permeability in the vertical direction so that vertical flow is not seriously restricted. Since this latter technique is a modified two-dimensional meal analysis, suitably structured three-dimensional reservoirs can be simulated at considerably lower computational expenses than is required using the three-dimensional analysis. A quantitative criterion is provided for determining when vertical communication is good enough to permit use of the modified two-dimensional areal analysis. The equations solved by both techniques treat both fluids as compressible, and, for gas-oil applications, provide for the evolution of dissolved gas. Accounted for are the effects of relative permeability, capillary pressure and gravity in addition to reservoir geomety and rock heterogeneity. Calculations are compared with laboratory waterflood data to indicate the validity of the analyses. Other results were calculated with both techniques which show the equivalence of the two solutions for reservoirs satisfying the vertical communication criterion. INTRODUCTION Obtaining the maximum profits from oil and gas reservoirs during all stages of depletion is the fundamental charge to the reservoir engineering profession. In recent years much quantitative assistance in evaluating field development programs has been provided by computerized techniques for predicting reservoir flow behavior. Because of the spatially distributed and dynamic nature of producing operations, automatic optimization procedures, such as those now in use for planning refining operations, are not now available for planning reservoir development. However, present mathematical simulation techniques do furnish powerful means for making case studies to help in planning primary recovery operations and in selecting and timing supplemental recovery operations. A number of methods have been reported which simulate the flow of one, two or three fluid phases within porous media of one or two effective spatial dimensions>-4 However, applying computer analyses to actual reservoirs have been limited mostly to two-dimensional areal or cross-sectional flow studies for two immiscible reservoir fluids. To obtain a three-dimensional picture of reservoir performance using such two-dimensional techniques, it has been necessary to interpret the calculations by combining somehow the results from essentially independent areal and cross-sectional studies. To the authors&apos; knowledge, the only other three-dimensional computational procedure, in addition to those presented here, was developed by Peaceman and Rachford8 to simulate the behavior of a laboratory waterflood. Two computational techniques which may be used to simulate three-dimensional flow of two fluid phases are described in this paper. The first method, called the "three-dimensional analysis", employs a fully three-dimensional mathematical model that treats simultaneously both the areal and cross-sectional aspects of reservoir flow. The second method, called the vertical equilibrium (VE) analysis", is applicable

By Tomás Vargas

The catalytic role of Thiobacillus ferrooxidans in the dissolution of chalcopyrite was studied by leaching pure massive samples of this sulfide with a pure strain of Thiobacillus ferrooxidans (ATCC 19859). Monitoring of the bacterial activity showed that an important fraction of the total bacteria generated during leaching remained attached to the chalcopyrite surface. Bacteria grown in the system, which were the offspring of bacteria adhered to chalcopyrite, was well explained as the result of the utilization of ferrous ion and sulfur as energy sources. The potential for indirect and direct action was fully utilized by the existing bacteria and the leaching process was controlled by the kinetics of chalcopyrite dissolution.

Jan 1, 1990

By T. D. Thomas

In this paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer&apos;s causes. The second cause will be discussed first. Misfires Caused by Faulty Detonators The important part of an electric blasting cap, to the user where multiple shot-firing is done, as in the steep-pitch, thiek-vein, anthracite mines, is the bridge wire. In single shot-firing this factor is not apparent, but in mines where multiple firing is done any variation in the resistance of the bridge wire, where full or even rated battery capacity is required, will most likely cause a misfire. The reason for this is obvious. If the resistance in the bridge wires is not the same, some of the detonators will fire because of their greater comparative resistance. Variance in resistance of bridge wires is caused by a slight difference in the diameter of the bridge wire, also by a difference in the composition of the bridge wires. Again, where the bridge wires have become rusted, there will be a variance in resistance. About the year 1922, one of the large coal companies was greatly alarmed by the number of serious and fatal accidents caused by misfires. The general manager issued an order that these accidents must be greatly reduced, and if possible, entirely prevented. The officials at the mines had to determine the various causes of misfires and have them corrected. The rock contractors who use large quantities of 60 to 80 per cent. explosives and do all firing electrically were thoroughly instructed as to the proper methods of doing their work, and closer supervision was given to their work. The manufacturer&apos;s representatives stressed the importance of the use of galvanometers; accordingly these were purchased and used. Larger firing lines were installed under the supervision of a demonstrator of the company manufacturing the caps and explosives. However, misfires again occurred and it was evident that the source of the trouble was not wholly

Jan 1, 1930

By Alper Kirmaci, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Injuries and fatalities resulting from roof falls are still a major concern in U.S. coal mines, and many researchers are focused on developing meaningful approaches to minimize this hazard. In the United States, coal mine roofs can vary widely in composition, geometry, and inherent heterogeneity, leading to a wide array of different roof fall failure types. Researchers frequently employ numerical modeling tools to reproduce this physical phenomenon and provide key guides to engineers regarding roof conditions and control as long as the input data and constitutive relations are appropriately selected. Simulating such complexity requires expertise and constitutive models that adequately simulate roof behaviors. However, the currently available constitutive models have shortcomings in capturing some of the roof fall failure types common in underground coal mines, such as guttering. A new constitutive model is developed to address the shortcomings of constitutive models commonly used for coal roof stability analysis. The constitutive model developed in this study combines the anisotropic-elasticity and nonlinear strain-softening responses. In addition, the developed constitutive model can simulate up to three different joint sets implicitly, allowing for use in both continuum and discontinuum settings, and can be used in both Lagrangian finite-volume and distinct element method codes of Itasca. First, the mathematical expressions of the model are provided. Afterward, the validation phase of the developed model that covers comparisons with analytical solutions and those of existing models (e.g., anisotropic elasticity, ubiquitous-joint, and bilinear strain-hardening/softening ubiquitous-joint plasticity) is presented. Finally, a hypothetical coal mine roadway facing high horizontal stress is simulated. The presented model successfully shows three distinct stages of a cutter roof in a shale roof: (1) initiation of shear cracks at the rib– roof intersection, (2) extension of cracks deeper into the roof (i.e., above the roof bolt length horizon), and (3) cantilevered roof. It is demonstrated that the presented constitutive model has the potential to help future researchers in simulating various roof responses.

Jul 1, 2023

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2slags that are typically encountered in the production of manganese containing stainless steels. Gas equilibration-quenching technique was employed in measuring the activities. Activity of Mn in Pt-Mn alloys were redetermined at 1600°C which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600°C. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient repression models were developed to predict the activities and activity coefficients of MnO in slags at 1600°C. Keywords: activity, MnO, slag.

Jan 1, 2004

The range of environments which control the level of ground support required vary greatly in terms of rock type, rock structure and the mining method used. At the operating mines visited during this review the level of ground support was such that incidence of rock-fall- related accidents were rare. It was also found that methods existed to support most of the conditions encountered. The main problem areas were weak rock, major geological structures, areas of heavy jointing, high development density and areas affected by high mining-induced stresses and blasting. With stope support the level of success was much lower than that achieved in development; the larger spans and more rapid changes in geometry of open stopes compared with cut and fill stoping (where cables were originally used) led to significant problems. Before a useable design method for cable support of stope walls and pillars can be obtained the precise failure mode of the walls and pillars, and the interaction of the support and the rock mass must be investigated.

Jan 1, 1982