Search Documents

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

Callie underground gold mine is part of the Newmont Tanami Operations, and is now the primary provider of ore to the Granites processing Mill. The Callie underground mine has produced in excess of 7.6 million tonnes (Mtpa) of ore, since production began in 1998, with a current production rate of 1.9 Mtpa. Callie underground uses sublevel open stoping with extraction through a combination of primary and secondary stopes. The primary stope filling strategy utilises cement aggregate fill (CAF) to allow full recovery of secondary stopes. The Callie backfill operation has had a continuous testing program in place during this time, which has resulted in a great deal of information available for post fill analysis. All CAF placement into primary stopes for Callie has been via surface boreholes and this has given Callie mine an understanding of some of the issues related to borehole design, type of linings to use depending on angle, depth and quantity of fill into stopes. Finally backfill barricades at Callie have undergone a number of changes during the time to optimise the design based on whether CAF or sand fill is used. This paper discusses the CAF backfill practices and testing methods used for backfilling operations at Callie.

Jan 1, 2005

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

Since the 1970s we have seen a marked corporate response in terms of the environment. In part this has come from regulation but it has largely come from stakeholders and the community. We now see a similar trend towards sustainability. The Brundtland (1987) definition of sustainable development provides a direction for advocates: the advance of human prosperity in a way that does not compromise the potential prosperity and quality of life for future generations. In my view its three essential components are: economic, environmental and community. The Global Mining Initiative and the contributions to the Rio World Summit and the Johannesburg World Summit on Sustainable Development indicate that sustainability is being taken very seriously by the mining industry. But does the minerals industry really embrace sustainability as they claim? There is a view that in reality sustainability is a non-event and that the triple-bottom line approach is only a convenient catch-cry for companies who are actually focussed very strongly on the economics part of the equation. Chemical engineers are showing a strong trend to more sustainable practices and the chemical industry has shown real commitment to research into developing sustainable processing systems. This requires a framework for thinking and design and the chemical industry is demonstrating true innovation as it moves towards æno wasteÆ technologies. Whilst there are limits to the rates of change that can occur the minerals industry should also be moving in a much more determined manner towards the notion of processing of products designed for whole-of-life cycle û with minimum/no waste. But is the minerals industry just paying lip service to the importance of research to sustainability?Several common themes influence the science and innovation agenda in Australia, which will affect the development and adoption of innovations by AustraliaÆs minerals sector. First is the well-proven link between peer-reviewed scientific excellence and commercial application. Second is the rise of multi-disciplinary Mode 2 research, which has developed in response to the complexity of problems faced by contemporary researchers, which are best analysed by combining expertise from two or more disciplines. Successful innovation outcomes, in any field, including minerals processing, is promoted by Mode 2 research which benefits from greater levels of networking and collaboration. Kofi Annan in his Message to the World Social Forum puts it very succinctly æThe way forward lies in finding constructive solutions togetherÆ.

Jan 1, 2004

By AIME AIME

THE session on milling methods on Monday afternoon.* with G. H. Clevenger, chairman of the Mining Methods Committee presiding, was well attended. However, none of the authors of the papers presented were present except Messrs. Taggart and Ince. The paper on "Elements of Operations of the Pneu¬matic Table," by Messrs. Taggart and. Lechmere-Oertel, was presented by Professor Taggart as was the paper on "Calculations in Ore Dressing," by Luyken and Bierbrauer, due to the absence of the authors.

Jan 1, 1929

By César Macher

Dada la importancia económica y social que tiene la seguridad e higiene minera en el país, el objetivo del texto radica en crear las bases de un programa de higiene y seguridad que defina, evalúe, controle los riesgos industriales, como capacite a los estudiantes de ingenería de minas para mejorar los servicios que presta en la industria minera. El curso comprende cuatro capítulos y la distribución del tiempo de enseñanza en un periodo semestral. Entre los aspectos básicos del programa está la definición, significado económico y legislación sobre los riesgos ocupacionales; el conocimiento de los riesgos industriales referente a los agentes químicos, físicos, biológicos en los centros laborales; el muestreo y determinación de atmósferas polvorientas o control de riesgos, prevención de incendios y explosiones, normas de seguridad, y la forma de organización de seguridad e higiene minera. De otro lado, las presentaciones teóricas del curso se complementarán con problemas prácticos de la minería, material bibliográfico, y el desarrollo de prácticas con facilidades del Instituto de salud ocupacional, concluyendo con una serie de exámenes parciales teóricos-prácticos.

Jul 20, 1959

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By Juanito C. Fernandez

INTRODUCTION The Philippines is endowed with mineral resources, much of which still remains unexploited. The country's known reserves, at least for the major mineral commodities, have increased every decade since the first major discoveries more than 80 years ago. Mining, therefore, naturally evolved as one of the pioneer industries and has ever since been a major factor in economic development. The Philippines has entered a new era in mineral resources development and management. One significant feature of this era is the degree to which the government is involved with the industry. In recent years, the state has increasingly encouraged the private sector to carry out detailed exploration aided by governmental contributions through extensive geological and geophysical surveys, fundamental researches and even indirect financial assistance in some specific areas. Significant changes in mineral resources development policies were brought about with the promulgation of Presidential Decree 463 or the Mineral Resources Development Decree of 1974. The Decree provides for a more rational system of administration and disposition of mineral lands to promote mineral resource exploration and exploitation. Various forms of incentives are provided. Foreign entities are allowed to participate in development through service contracts with leaseholders or with the government in the case of reserved areas. The thrust in mineral resources development has been focused on the base metals which as envisioned would provide the foundation for sound economic development. In recent years, however, major strides have been made to promote the exploitation of the non-traditionally produced commodities especially the non-metals. Development likewise point to the growing determination of the government and the private sector to expand benefits from mining. This is evident in efforts to promote downstream processing operations and to encourage investments in exploration, exploitation and mineral processing ventures. The integrated mineral resources development plan, therefore, proposes the vertical integration of mining extraction activities with the processing requirements of the metal-based manufacturing industries. While mining activities shall continue to be carved out by the private sector, the government shall influence the industry's direction by establishing legitimate goals to maximize benefits through an integrated approach giving due consideration to environmental protection and resource needs of future generations. STATUS OF MINERAL RESOURCES DEVELOPMENT Extent of Exploration Application of modem exploration tools and concepts complemented by intense infusion of foreign technology and rapid development of indigenous expertise have enabled the government jointly with the private sector to geologically explore vast grounds and to expand the country's known mineral resources. Approximately 93% of the country's total land area of 30 million hectares have been geologically mapped on at least 1:250,000 scale. Of the 93% total coverage, roughly 37.54% or 11.07 million hectares have been done on scales of 1:10,000 to 1:50,000 as shown in Figure I. Only 3.07% of the total coverage have been surveyed in detail. Land gravity surveys have been undertaken on over 45% of the total, while some 77,300 line km. of aeromagnetic surveys have been flown over 110,000 sq. km. of land area. Processing of data is almost complete. Total magnetic intensity and IGRF-corrected maps are available. Geological interpretation utilizing Landsat MSS imagery and low altitude aerial photography augmented by ground truthing have been undertaken in several large areas with very encouraging results. Beach and offshore mineral surveys were initiated in 1977 and have covered substantial areas in northwest and southeast Luzon and northeastern Mindanao. Highly promising areas for detrital magnetite, chromite, gold and some heavy minerals including ilmenite and titanium have been identified. In the petroleum sector, two offshore oilfields are currently producing from Miocene limestone reefs in Northwestern Palawan. Another field from the same area will be on stream in mid-1982.

Jan 1, 1982

By Arthur A. Schweizer

A method to improve the quality of Magmnt zinc concentrates to become acceptable feed to an electrolytic zinc refinery. The magnesia content of zinc concentrates produced was too high due to particle locking with the sphalerite in coarse fractions. Regrinding of the concentrates to a very fine particle size and then refloating the sphalerite was chosen to eliminate a sufficient amount of the magnesia to make the concentrates acceptable.

Jan 1, 1981

By PATRICK R. TAYLOR, NICHOLAS BELLUSCI, D. ERIK SPILLER, VICTOR BRAMAN

Most of the world’s production of natural soda ash comes from the mining and processing of trona found near Green River, WY. The processing of trona ores to ultimately yield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale, is water and energy intensive. It is speculated, however, that the glass-manufacturing industry, which is the largest consumer of soda ash, may be able to use product of a lower grade and consistent level of the insoluble constituents. Thus, the viability of using sensor-based sorting to produce a beneficiated trona stream that would be fed to calcination was investigated. The study encompassed the preparation of a run-of-mine (ROM) Green River ore sample; selection of specimens sized 25 to 75 mm; imaging of the specimens by sensors based on X-ray transmission (XRT), color and laser-induced fluorescence (LIF); insolubles analysis of the specimens; and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content exists, and that a surface-detection-based sensor, particularly LIF, is apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65 percent separation efficiency and a 70 percent recovery of trona could be achieved.

Feb 1, 2023

By Y. H. C. Wang

A detailed study of carrier flotation of kaolin clay using calcite showed the major beneficiation mechanism to be enhanced aggregation between anatase and calcite under intense agitation conditions. In order to develop an understanding of this selective aggregation, surface charge characteristics of kaolinite, anatase and calcite were studied under simulated flotation conditions. Zeta potential of all these minerals tended towards a constant negative value in ole- ate solutions under certain conditions possibly due to adsorption or precipitation of oleate on them. However, whereas the zeta potential of anatase in the oleate solutions was not influenced by the agitation level, that of kaolinite was found to be strongly dependent on the agitation intensity. The effect of oleate on zeta potential of kaolinite was reduced by an increase in agitation intensity. It is suggested that oleate is much more firmly bound to the surface of the anatase and that this preferential attachment is responsible for the enhanced selective aggregation of the anatase with calcite. Agitation level plays a major role in carrier flotation since intense agitation is considered to en- hance both the chemisorption of oleate on anatase and preferential detachment of calcium oleate precipitate from the kaolinite surface, all of this producing a large difference in the surface properties of anatase and kaolinite, and hence in their tendency to aggregate with calcite.

Jan 1, 1981

Percussion drilling with tungsten carbide insert button bits ranks among the most significant advances in both underground and surface drilling in medium and hard rock formations. Getting top performance and life from these upfront components is not particularly difficult if one pays attention to the basics in operation and maintenance. For some reason, a few of the essential operating and maintenance steps for getting the most from these tools seem to have gotten turned around; instead of operating at the near optimum levels, some miners, in following myths or misunderstandings about them, are shortchanging their optimal utilization. Let's examine the two most harmful ones.

Jan 8, 1978

By F. C. Muttitt

The physical arrangement of the continuous casting facilities at Algoma have been described a number of times in previous papers. For the purposes of this discussion, it is sufficient to state that the casting plant is located at a considerable distance from the basic oxygen shop which supplies it, involving a relatively lengthy ladle transfer movement. (Fig. I) The handling of the ladle by two separate cranes, first to the argon station, and thence to the casting machines, results in an average interval, from start tap to start cast, of 45 minutes. The effects of such extended retention time on temperature control and on refractory performance are well known. Tapping temperatures well above normal are necessary to insure that the ensuing heat losses do not result in an undue incidence of premature tundish freeze-offs. The heat lost, as well as being a function of the retention time, becomes more critical with smaller ladle size; winter temperatures add to the problem with their effect in chilling ladles and increasing radiant losses.

Jan 1, 1972

By T. Egleston

circumstances, would prefer the steel with which they are now familiar, to a specimen that Mr. Sandberg has described as having broken into seventeen pieces under the wheels. After blowing such low manganese steel, it may be coaxed into a rail, but it is a wonder that it holds together so long as it does, with so great a nornber of minute flaws. I would not in any way depreciate chemistry, but I think it should be kept in its proper sphere. Let the chemist look after the quality of pig metal, and apply common sense in the avoiding of extremes, then the most fastidious railroad cannot find fault with the result. PROFESSOR EGLESTON, New YORK City : It is not my place as an engineer to apologize for the chemists, but as no one seems disposed to do so, and as they have had more than their share of criticism, 1 am glad to say that I believe there are chemists in this Institute whose work and word are just as reliable, arid perhaps even more so, than that of the average engineer. But we ought to make a distinction; there are chemists and chemists. With the ordinary commercial chemist, who looks upon the science as so much merohandise, I have not a particle of sympathy; but with the chemist who looks upon his profession as engineers do upon theirs, I have every sympathy. When matiufactorers and engineers go to a chemist and ask him to make an investigation, and scretv him dowu to the lowest point, turning the equivalent of his brains into cents and mills, they ustially get an exact equivalent in poor work for miserable pay, and no one has or should have any sympathy with them, and the under these conditions has no right to ask for any, and no reason to criticise any work that he may get under such circumstances. But I am disposed to think that the chemists who have been replwented and discussed at this meeting do their work conscientiously, and that it is as reliable as that of almost any profession. I believe, however, that this problem of steel rails is being investigated in a wrong direction. I said so at the Pittsburgh meeting, and I think the discussion of this meeting will prove it to all those who have heard it. I think the chemigt is incapable of solving this problem unlees he goes very far into the domain of physical chemistry, so far that it becomes physics and not chemistry; and that the physicist will be the one on whom we must rely in the future for the elucidation of the subject. The chemist may aid the physicist, but it is my decided opinion that we are looking in the wrong place to get the explanation of the phenomena.

Jan 1, 1881

By J. C. Donnell, O&apos

Sinking an inclined ventilation shaft at the Never Sweat mine of The Anaconda Co. has required a unique underground hoisting arrangement because the shaft changes direction from vertical to 71.5º. Access to the project is made through the High Ore shaft to the 2800-ft level, then by crosscut to the bottom of the vertical Never Sweat shaft. The 71.5º incline shaft starts at this point, which makes an unusual operation as the 60-cu ft sinking skip coming up the incline changes into a vertical position above the 2800-ft level before going into the dump scrolls. This requires both rollers and guide shoes on the skip. Coming up the incline to the collar of the shaft the loaded skip enters into a guard before reaching the vertical section. The tendency of the surface- mounted Never Sweat hoist is to lift the front wheels of the skip off the track, so the guard keeps the skip on the rails during the transition.

Jan 11, 1965

By Rafael de Andrade Silva

O presente trabalho teve como principal objetivo estudar a evolução da recristalização em chapa de zinco, e para tal objetivo, chapas finas de zinco laminadas a quente foram sobrepostas e processadas pela técnica de deformação plástica severa conhecida como NECAE (Non Equal Channel Angular Extrusion). Em seguida, as amostras foram submetidas a um tratamento térmico de recozimento para recristalização com diferentes temperaturas e tempos de encharque. Para tal objetivo, foram utilizadas análises de microscopia óptica e dureza Vickers. De acordo com os resultados obtidos, observou-se que após o processamento via NECAE houve uma pequena fração recristalizada, e esta aumentou de acordo com o aumento do tempo e da temperatura de tratamento térmico.

Aug 16, 2017

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese (Mn) ferroalloys are chiefly consumed in the steelmaking process as a deoxidizing agent or as an alloying element to produce high-quality steels. These alloys are typically produced in a submerged arc furnace using coke, fluxes and manganese ores of a specific manganese/Fe (Mn/Fe) ratio. Preferred-grade manganese ores should have Mn content greater than 46 percent and Mn/Fe content greater than 5 to produce commercial-grade, high-carbon ferromanganese [1]. Selective mining of high-grade Mn resources has created a scarcity of these resources, which is emerging as a major challenge for the manganese and steel industry. Manganese ore resources are mainly distributed in South Africa, with about 32 percent; Ukraine, with about 17 percent; Australia, with about 17 percent; and Brazil, India, China, Gabon and Mexico, with lesser amounts.

By Roger Scarr, Richard A. Walker

Interactive video is the combination of computer and laser disc -technologies that allows for the storing of 54,000 single images or 30 minutes of video with the ability to access any segment or single image within a half a second. This capability combined with the use of a graphics overlay on the video and accessed through a keyboard or touchscreen creates a very powerful and versatile marketing or training tool.

Jan 1, 1990

By Robert J. McCarthy

Mining has a record of achievement in developing and adopting new technology to facilitate the extraction of increasingly challenging resources. Certainly larger, or more capable, mining equipment has allowed mining companies to mine mineral deposits at lower unit costs; however, there has also been the advent of computerized systems that aid in the management and tracking of mining operations. Unfortunately, the latter computerized systems have not always had the success anticipated with their implementation. This paper explores the view that increased transparency of the planning and operating cycle in a mine, as provided by certain computerized systems, can result in some resistance from those whose work becomes ?exposed?. Examples are drawn from industry-leading technologies for both mine management and reconciliation that illustrate the issues and challenges that result. The adoption of appropriate change management principles is suggested as a best practice in planning and mitigating the challenges in implementing technologies which increase transparency in the mining environment.

May 1, 2011

By P. A. Lindberg

Early Proterozoic ore deposits in the Verde district at Jerome, Arizona have produced 33.7 million metric tons of ore (1893-1975). The United Verde and United Verde Extension deposits produced most of the ore that yielded 1,644,323,100 kg Cu plus large amounts of Au, Ag, and Zn. These deposits are situated on the fractured and hydrothermally altered apex of a large submarine rhyolitic extrusive (Cleopatra formation). Precambrian lithologies are penetratively deformed and at Jerome the Fl folds plunge steep to the NNW. For the past two decades the volcanogenic model has superseded the replacement theory of ore formation.

Jan 1, 1992