Search Documents

By M. H. Marvin

This report presents the results of a program to develop backfilling techniques to mitigate undesirable effects of hydraulic borehole uranium mining. Large underground cavities, formed during the borehole mining process, can be backfilled to prevent ground subsidence and to allow mining of adjacent uraniferous sandstone. Three backfilling techniques were tested in the laboratory and in the field: bulk dumping of slurry into the borehole from ground level, slurry injection under water, and slurry injection above the cavity water level. These techniques were tested with sand and with sand and one percent cement (by weight) mixtures. The project was accomplished in four tasks: equipment preparation and transport, mining operation to generate a full-sized cavity, backfilling operation, and assessment through core samples and subsidence checks. The concentrations of cement mixed with sand proved to be inadequate to bond the sand. Bulk dumping resulted in a 30-degree angle-of-repose, much too steep to completely fill the cavity. Both slurry injection techniques filled the cavity satisfactorily. However, underwater injection is the recommended backfilling technique because the borehole water level does not need to be pumped down during backfilling. The borehole itself was filled by bulk dumping of slurry. In conclusion, backfilling of borehole mining cavities is entirely feasible, and the preferred method is slurry injection under water.

Jan 1, 1979

By Peter A. Hacquebard

"Two continuous coal zones occurring in a 2500f t (762 m) thick section of the Upper Carboniferous Pictou Group (Westphalian C and D) have been encountered in five offshore wells drilled f or oil and gas in the Gulf of St. Lawrence. They correlate, by means of fossil spores, with thick coals of the Mabou and Inverness coalfields situated at the eastern margin of the Basin. Therefore, the presence of a large submarine coalfield of at least 18000 sq mi. (46 620 km'] is indicated. This compares with an estimated size of 14 000 sq mi. (36260 km' ) for the Sydney Coal Basin.Accessibility is provided only by the small onshore parts of the Mabou and Inverness fields, because farther offshore the coals lie too deep to be mined (below 4 OOO f t ([ 219 m)).Two near-shore coal exploration wells indicate that at Mabou Mines the younger Inverness coals occur at a mineable depth to at least 5 km from land. A structure contour map of this area shows a reserve of 125 million tons in two Inverness equivalent seams that are 8.5 ft (2.6 m) and 4.5 ft (f.4 m) thick. The Mabou coals, however, reach too great a depth close to shore to possess mineable resources.A structure contour map of the Inverness submarine area, based on mine data and one off shore seismic profile, indicates inferred mineable resources of 160 million tons, in two seams that are 7ft (2.1 m) and 4.5 ft (f.4 m) thick . A detailed deep seismic survey will be necessary to substantiate the structure and resource estimates"",Maceral and coal quality percentage diagrams of five column samples of these seams (the 7 Foot and 13 Foot Seams of Inverness Equivalents) show a bright banded coal, high in reactive macerals, which will produce a weak coke unsuitable f or metallurgical purposes. A thermal coal with a rank of H. V. ""B"" Bituminous (0.64% Ro) is present, averaging 12000 btu llb (6 660 kcai/kg), 10% ash and 6% sulphur, of which 60 to 80% is derived from pyrite.Microlithotype profiles of the major Mabou and Inverness coals show characteristic successions that can be used f or seam identification and proved valuable f or structural interpretations.The time of faulting in the major fracture zone on the eastern margin of the Gulf of St. Lawrence Basin has been deduced from coal rank variations. It occurred in pos tPermian, probably Early Triassic time."

Jan 1, 1986

By L. W. Blau

RESEARCH work in exploration and production was further reduced during 1943 owing, partly, to difficulties in the acquisition of apparatus and, principally, to the exodus of research men to governmental agencies conducting research and to the armed forces.

Jan 1, 1944

By Edehran Lotfi, Terrence Stobbe

INTRODUCTION Mobile excavating and handling equipment are important 'tools of trade' in the mining and construction industries. The handling of this equipment must be mastered so that its limitations are learned and its harmonic use with other pieces of equipment is practiced. he sudden growth in mobile excavating and handling equipment type, size, complexity, and application started after the Second World War. This growth has not been accompanied by pertinent human factors research. Investigations into the proper and safe handling of such equipment with due regard for human and machine limitations are lacking. One such piece of equipment is the front-end loader (FEL), which during one cycle of operation excavates, loads, and hauls, (Lotfi and Adler, 1981). The diversity of action by FEL is archetypical among excavating and handling equipment. Front-end loaders are the most rapidly proliferating type of equipment in the industry. Also, front-end loaders are involved in the highest number of accidents involving mobile excavating and handling equipment. In the period 1970 to 1978, FEL's were involved in 27% of all mobile equipment accidents in surface mining (Adkins, 1980). Improving operational safety and efficiency will reduce the frequency of accidents. The performance of the operators can be evaluated and improved by the following steps: first, define the operating conditions and the operator workload intensity (Adler and Lotfi, 1983), second, monitor the operator to evaluate his task performance, and third, make recommendations based on the findings. The stressful nature of the equipment operating task is an acknowledged fact (Field, 1980). However, a systematic measurement of stress evaluation is lacking. In this paper, methods for measuring mental stress and fatigue, are defined, the mental load which caused the stress is outlined, and stress measurement methods are proposed. MENTAL STRESS Mental stress has been described as a "specific somatic response to damage or the threat of damage by several environmental agents"

Jan 1, 1986

By Reid A. F

Since early 1971 Western Titanium N.L. has been operating an ilmenite upgrading plant on a commercial basis at Capel, Western Australia. In their process ilmenite is pre- oxidized, then reduced in a rotary kiln to a mixture of metallic iron and titanium oxides. The iron is leached out by accelerated rusting in aerated water, leaving a product with titanium content, expressed as Ti02, of about 92%. Samples from different stages of the up- grading process, representing operations over the last two years, have been studied in detail by X-ray diffraction methods, and the sequences of phases and reactions occurring have been determined. Quantitative X-ray studies showed the ilmenite feed materials to consist of a mixture of ilmenite and pseudo- rutile. Pre-oxidation of the ilmenite at =1000¦C leads to the formation of rutile plus a Fe2TiO5-FeTi205-Mn2TiO5 solid solution. The final reduction product consisted of a mixture of metallic iron, reduced rutile and a FeTi05-MnTi205-Ti305 solid solution. The relative amounts of these reduction products were very sensitive to the initial concentra- tions of the minor constituents manganese and magnesium. The effects of variation of ilmenite feed rate, reducing atmosphere,- reduction temperature and controlled addition of magnesium were also studied.

Jan 1, 1973

By Weng Fu

In this study, Resin-in-Pulp (RIP) technology is used to separate Pb from a chalcopyrite slurry. Solvent-impregnated resin, Lewatit® VP OC 1026, which contains di(2-ethylhexyl) phosphoric acid (D2EHPA) in a macroporous polystyrene matrix was used, as the functional group exhibits selectivity for Pb over Cu. Adsorption pH, kinetics, as well as resin and CuSO4 concentrations were investigated. The results show that the kinetics of Pb and Cu loading are fast, reaching the adsorption equilibrium within 30 min. The equilibrium pH of 2 was chosen as optimum for operation in order to achieve a high Pb extraction rate and extent as well as selectivity for Pb over Cu. High Cu(II) concentration in solution results in Pb(II) requiring a larger amount of resin for the same degree of extraction. Regeneration and reuse tests show that the loss of adsorption capacity happens in the 1st and 2nd cycles and then the adsorption capacity stabilises for the 3rd cycle.

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Oliver Q. Leone

Electrorefining tests using titanium-nitrogen alloys as anode material showed that no significant quantity of nitrogen was transferred to the cathode deposit. The nitrogen of the anode remained in the scale, and the titanium-nitrogen alloy was anodically insoluble in the electrolyte when the nitrogen content was 11 weight-percent.

Jan 1, 1966

By Ehsan Vahidi, Fereshteh Rashchi, Ataollah Babakhani, Alireza Zakeri

"The synergistic effect of Cyanex 302 on solvent extraction of nickel and cadmium from sulfate solution with D2EHPA diluted in kerosene was investigated with the aim of increasing separation efficiency. Experiments were carried out within a pH range of 0.1-5.0 using sole D2EHPA and D2EHPA-Cyanex 302 mixtures in different ratios. Increasing Cyanex 302 to D2EHPA ratios in the organic phase caused a left shifting of the extraction isotherm of cadmium and a right shifting of the extraction isotherm of nickel. As a result, optimum separation was found with a Cyanex 302 to D2EHPA ratio of 0.1M:0.5M. In the present system, effect of a modifying reagent such as TBP was studied. The influence of various diluents including kerosene and carbon tetrachloride was also investigated.IntroductionBatteries are popular sources of portable energy. Ni-Cd batteries are manufactured in two main groups of small domestic cells and large industrial batteries with 80% being in domestic use. Ni-Cd cells have various uses, for example in cordless electric utensils, cordless telephones, airplane engine starters, and communicational distribution systems [1].Depleted Ni-Cd batteries are classified as hazardous waste since nickel and cadmium are heavy metals and suspected carcinogens. Given the risk associated with uncontrolled disposal, directions for issuing legislation on disposal and recycling of used batteries have been made in industrialized countries [2]. Recycling of Ni-Cd batteries is important from both economic and environmental points of view. Different methods have been used for recycling these wastes through pyrometallurgy [3], biotechnology [4,5], and hydrometallurgy [1,2].Due to the advantages of hydrometallurgical processes, several studies have been implemented on leaching and solvent extraction (SX) of the used Ni-Cd batteries. Leaching of batteries is usually done in sulfate or chloride media; while solvent extraction has been used in different extractants: two-stage solvent extraction by D2EHPA and Cyanex 272 [6]. Solvent extraction of Cd from leach solutions has been studied using various extractants; Cyanex 301 [1], D2EHPA [7], Cyanex 302 [8], Cyanex 923 [9], Cyanex 272, Tops 99, PC88A [10]. Application of phosphorus based extractants for the solvent extraction studies of Ni such as TOPS 99 [11], D2EHPA [12], Cyanex 272 [2], has been investigated. Separation of Cd(ll), Ni(II), and Co(ll) from chloride leach liquor of spent batteries [13], were explored in the earlier studies. Cd extraction with D2EHPA involves co-extraction of both Ni and Co [14], which causes issues in the separation process efficiency."

Jan 1, 2012

By H. Mogollón

El presente texto señala el proceso de fabricación del alambre y cobre en la Cerro de Pasco Corporation, así como los métodos adecuados para su elaboración. Bajo el amparo de la ley 13270 de promoción industrial nace la Compañía Industrial del Centro, subsidiaria de dicha corporación, y responsable no solo de la producción de barras y alambrón de cobre, sino de la producción de ácido sulfúrico en La Oroya. Actualmente, esta producción se ajusta a 90 toneladas métricas de alambrón redondo de cobre refinado con un diimetro nominal de 7,9375 mil metros. Sin embargo, esta pueda ampliarse hasta un máxlmo de 145 toneladas métricas a través de cambios menores en el equipo auxiliar.

Nov 20, 1967

By C. H. Bertoni

"The Superior Province of the Canadian Shield is the largest gold producing area within Archean greenstone rocks in the world, with total production of over 140 million ounces of gold. One hundred and fifty-five mines have individually produced more than 8,000 ounces, although only a relatively limited number of deposits (33) produced more than one million ounces of gold. The output from these 33 deposits accounts, however, for 85% of total gold production. The majority of grades (68%) ranges between 0.10 and 0.30 ounce per ton, and there is no linear relationship between grade and tonnage.Development of new gold mines reflects the history of gold prices. However, the response to the latest increase in gold prices was not as marked. It is concluded that gold deposits are becoming increasingly more difficult to find and new exploration techniques are urgently required.IntroductionWith most of its production coming out of the Superior Province, the Canadian Shield is the largest producer of gold from Archean greenstone rock s in the world. In total gold production, the Superior Province is surpassed only by the paleo-placers of Witwatersrand and the placers of the USSR (Anhaeusser, 1976). There has been no attempt so far to compile the historical production of the Province as a whole in a single document. The aim of this work is to fill this gap, not only for the convenience of having a complete list of gold producers, but, more importantly, as a basis on which to study the tonnage and grade characteristics of these deposits."

Jan 1, 1983

By N. J. Grant, I. S. Servi, A. Chaudhuri

IN a recent paper by Servi and Grant,' it was illustrated that the slip band spacing and stress based on creep test data were related by the equation: d =1/ where d is the spacing in millimeters and v is the stress in psi, based on a more complete equation proposed by Orowan. It was shown further,' that for a. given grain size, the slip band spacing became larger with decreasing stress (and was independent of temperature), until such time that the slip band spacing becomes greater than about one-half the grain diam- eter. When this occurred, the mechanism of deformation in creep of 2s aluminum at high temperature changed from slip to grain boundary deformation (sliding). Additional metallographic evidence is now available which confirms this in a most interesting fashion.

Jan 1, 1954

By M. J. Buerger

POSSIBLY the most puzzling features observed during a single-crystal deformation test are the appearance of slip striae on the surface of the crystal and the strengthening of the specimen.1 While the first phenomenon is mainly of theoretical interest, the latter is fundamental to all strain-hardening and cold-working processes in which the deformation occurs by translation. The plastic deformation of crystals has received considerable discussion2 and need not be reviewed here in any great detail. It has been observed, essentially, that after a certain amount of initial stress is applied, the surface of the crystal becomes covered with sets of parallel striae or rings which appear to divide it into thin slabs or slip blocks.3 The striae are the traces of rational crystallographic planes along which shearing movements are localized, these movements providing the strain which accompanies stress applied beyond pure elasticity. As deformation under the applied stress proceeds the slip blocks shear past one another, although the essentially single-crystal character of the specimen is unimpaired. All of the shearing apparently takes place in the immediate vicinity of the original slip striae without the appearance of new planes of movement.4 Since each increment of strain is attended by an increased stress requirement to continue the deformation, the crystal strengthens during the process.

Jan 1, 1928

By A D. T Goode

Data Metallogenica (DM) is unique as a global mineral sample collection and deposit database with over 70 000 rock samples and a wide range of descriptive, photographic and measurement data. Subscribers have access to approximately four gigabytes of on-line data with many examples included on the public pages. DM commenced its life on the Pacific rim in 1971 and much recent growth has focused on countries of the Pacific margin, particularly Australia, Fiji, Chile, Indonesia and Peru. Approximately 600 separate deposits and mineral occurrences in this region are represented in DM. The sets of rock samples have been photographed at high resolution and included on the web site, together with unpublished descriptions, deposit cross-sections, bibliographies, field and mine photographs, petrology and reflectance mineralogy. Figures and abstracts from PhD theses are a new addition and the donation of proprietary databases by companies and individuals is an encouraging trend. DM increasingly is being viewed as an acceptable and important repository for æfragileÆ and irreplaceable personal and company data, it is also being recognised in its true light as a high level information system, not solely a collection of rock samples. Data Metallogenica is a not-for-profit venture of AMIRA International that requires self-funding from December 2004. Growth and development must be funded entirely out of subscription and sponsorship revenues because no government subsidy is provided. The Pacific rim is in the mainstream of mining and exploration activities worldwide and those involved have much to gain from a dynamically sustaining DM. The home page at www.datametallogenica.com contains much example data and details of subscription and membership rates.

Jan 1, 2004

By A. K. Gangopadhyay, J. J. Moore

The effect of grinding media composition, mineral type, and slurry environment on the wear rate of various grinding media (balls) are discussed. Sufficient wear data have been obtained and correlated. Modes of wear were determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1986

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O'Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O'Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling ' must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O'Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O'Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling ' must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By D. M. Jamieson, M. P. Pearse, E. R. A. Plumstead

In 1948 the shaft sinking record in the Republic of South Africa was held by the Van Dyk Consolidated Mines Ltd. for a ventilation shaft with a footage of 461 ft sunk during the month of August 1941. This record remained for some ten years; but in the ensuing nine years it was broken no less than 13 times. Table I gives shaft sinking records throughout the world for the 21 years, 1940 to 1960. History shows that the wide, deep, timbered rectangular shaft had passed its peak of popularity by 1948, although it still had a great deal to commend it, both from the sinking and operational points of view. In sinking, it is easy to clean manually, and water can be handled by bailing when wet ground has to be negotiated; its shape also lends itself to equipping concurrently with sinking. In operation it provides the most convenient "in line" hoisting arrangement, and if the ventilation requirements so demand, it offers the simplest solution in that it can be divided into upcast and downcast sections. Furthermore, in the case of a multi-level mine, the shaft compartments can be reduced conveniently if the full area of the shaft is not required to serve all levels.

Jan 4, 1963

By Charles Austin

IT has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A, critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publications1,2 have shown that the factors controlling graphitization below the A, are different from those operating above the A, inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemi-cal analyses. Many years ago it was recorded' that the rate of graphitization at subeutectoid tem-perature is not a maximum just below the A, critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is im-possible to spheroidize certain steels in the temperature range of 650° to 710°C. with-out the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A, (720°°C,) these same steels may be completely sphe-roidized at constant temperature. In previous studies1,2,4 on 1 per cent plain carbon steels graphitization was en-countered during prolonged tempering. The limited number of steels studied did not provide sufficient data to permit adequate study of the factors controlling this graphi-tization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, fur-nished by four steel companies, who also supplied information regarding the history of manufacture.

Jan 1, 1940