Search Documents

By Safdar A. Gill

The technique of installing small diameter caissons (drilled piers) through soft clays and water bearing ganular soil is well established for constructing building foundations. Over the past few years, the method has been utilized for constructing a large number of shafts extending into rock for the Chicago's Deep Tunnel Project. This paper will discuss design considerations for obtaining the most economic ground support system, the impact of construction procedures on the support and lateral pressures for design. Construction procedures will be described along with performance of the shafts.

Jan 1, 1981

By G. Wonnacott

A model for simulation of gravity regrinding circuits is presented. The model can predict "secondary" density distribution data from a series of "primary" grind/density distribution tests. Thus middlings regrind requirements can be predicted from primary grind data. Traditional methods of regrind design involve lengthy and tedious tests programmes. The model presented herein can considerably reduce the quantity of testwork required for regrind design. The model can also be used to design primary gravity grinding circuits. A parameter estimation scheme and experimental data validating the model are presented.

Jan 1, 1989

By Katsunori Okaya, Toshio Inoue

Application of the discrete element method incorporating the simple kinetic model of the ball-to-ball and ball-to-wall interactions enables us to visualize the details of the grinding actions prevailing in the ball mills. We have developed a computer program to represent a generic mill model with which we can simulate tumbling mills, vibration mills, centrifugal mills and planetary mills. While the program can be used for various purposes including design of new equipment, one obvious application of it is the analysis of the conventional tumbling ball mills for better understanding and improvement. The purpose of this paper is to present a model and to observe its behavior in particular attention to the spatial distribution of the energy dissipation as well as the energy spectrum and their dependence on the major parameters such as mill speed, ball filling, liner configuration, slurry viscosity and the hardness of the ore.

Jan 1, 1995

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-' ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration 'of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913

LARGEST known fluorspar deposits in the world are mined in southern Illinois (Hardin County), and northwestern Kentucky (Crittenden County). Colorado, New Mexico, Montana, and Utah are the principal western sources in the U. S. Rosiclare Fluorspar District Hardin County, Illinois The Rosiclare area is located in the southern part of Hardin County on the Ohio River where the Illinois Central Rd. branch line terminates and provides transportation. Fluorspar has been mined commercially in this area since 1870. Aluminum Co. of America and Rosiclare Lead & Fluorspar Co. are the two major producers in this area. Ozark-Mahoning Co. operates a concentrating plant in Rosiclare but the bulk of its ore is mined near the town of Cave-in-Rock.

Jan 1, 1958

By Maurizio Violo, Arjan Beqiraj, Umberto Masi

"Abstract - Four main podiform occurrences of chromite have been distinguished in the ultramafic Bulqiza massif, Albania; they are associated from the bottom to the top with: i) basal harzburgites (lower tectonite sequence), ii) dunitic lens-bearing harzbugites (middle-upper tectonite sequence), iii) layered chromitite-bearing dunites of transitional zone, and, iiii) the stratigraphically lowermost part of the magmatic section. However, only the occurrences hosted by rocks ii) and iii) are economically important.Chromite compositions similar to those of other podiform chromites are bimodal. Thus, chromites from occurrences ii) and iii) are richer in Cr than chromites from the other two occurrences. Accessory chromite disseminated throughout the massif is richer in Fe than orebody chromite, displaying similar range of the Cr/Cr+Al ratios, with accessory residue chromite matching the characteristic (Cr/Cr+Al >0.6) range of type-III Alpine peridotites. Both orebody and accessory chromites show compositional ranges correlating with host-rock compositions, i.e., the Cr-rich chromites are hosted by the most refractory ultramafic rocks. Therefore, the Cr/Cr+Al and Mg/Fetot (Cr/Fetot) ratios of chromite are useful for exploration of high-grade, metallurgical chromite ore at Bulqiza and in other massifs of similar geodynamic setting."

Jan 1, 2000

By Fernando Zevallos

La mayoría de las personas que se han involucrado en minería evidencian el gran nivel de sofisticación y la multidisciplinariedad en los procesos mineros. Actualmente, la tecnología está alcanzando a la ciencia ficción y nos presenta equipos de transporte autónomos o robots que realizan levantamientos topográficos. Sin embargo, existen nuevos retos que esta nueva tecnología debe afrontar como la disminución de impacto ambiental. En particular este trabajo técnico tratara los esfuerzos y dificultades que enfrentan la minería subterránea en descarbonización y gestión de residuos desde un enfoque de estudios de factibilidad o prefactibilidad y algunos ejemplos en operaciones.

Sep 30, 2022

By Aline Lima da Silva

The present work is focused on the thermodynamic study of the methane or biogas mixtures conversion on Cu-ceria catalysts. Several experimental studies reported in literature have demonstrated the ability of these materials to operate as SOFC anodes for direct methane oxidation, with the evidence of enhanced tolerance towards sulfur poisoning and carbon deposition. More recently, experimental investigations have shown the feasibility of Cu-ceria anodes to directly operate with simulated biogas feeds at intermediate temperature (1023K). In this way, the effect of the ceria redox properties on the equilibrium composition is investigated, considering methane or biogas mixtures as the fuel. Conditions under which carbon deposition and sulfur poisoning can be prevented are determined. Our study combines results from the classical thermodynamics, obtained with the help of FactSage software, with the new Cu-S and Ni-S diagrams proposed in literature, which were calculated based on the Density Functional Theory (DFT). These diagrams are able to predict a region where sulfur interacts with the metal surface through chemisorption. A comparison between the performances of Ni-YSZ and Cu-CeO2 catalysts is established from a thermodynamic viewpoint. Theoretical results are in agreement with the experimental trends from literature.

Aug 8, 2018

By O. W. Ellis

RECENTLY there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2? alone gave reliable information in this regard. Even today his determination's of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time-their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systematic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington,16 Smalley33 and Thibaud45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper.

Jan 1, 1929

By Milton H. Fies

THE Alabama Power Co. operates its Gorgas mine in Walker County, Ala., immediately adjacent to its steam plant. The coal mine property consists of some 19,000 acres of fee and mineral ownership lands, and all of the production from the mine-approximately 2500 tons per day-is utilized at the company's adjoining steam plant. The company is presently considering the purchase of additional acreage adjoining its present holdings which acquisition will almost double its reserves. The coal is transported from the mine over a short railroad spur in the company's own equipment, either directly to one of the large plants at Gorgas or to a storage pile. The longest haul is about 1 1/4 miles.

Jan 12, 1950

By Z. Pilecki

This work concerns the identification of weak zones in the structure of a rock mass endangered by outburst of gases and rocks in the Rudna copper ore mine at greater depths (approximately 1200 m). A special methodology has been undertaken for the recognition of that threat in the wake of an outburst in the mine in 2009. No similar phenomena have been previously recorded in KGHM Polska Miedz copper ore mines. The research described in this paper was carried out in the new part of the deposit prepared for mining. Geophysical methods were used: seismic tomography and borehole ground penetrating radar (BGPR), along with particular identifications using geological engineering methods. In the researched area, Permian layers of sandstone and shale clay (Weissliegendes formation) and of Zechstein dolomite (top of Rotliegend formation) and anhydrite occur in the copper ore deposit. The rock layers are characterized by variable thickness and intensity of mineralization, varying internal structure, and local fracturing containing different gases and water. It is assumed that accumulation of gases occurs in the tectonically fractured dolomite. The study was focused on the recognition of the structure and properties of the dolomite layer lying directly within the roof of excavations. The first tests were performed with seismic tomography for the recognition of anomalous changes in the elastic properties of the rock mass. The results of these studies were used to design a control borehole for a detailed geological engineering assessment and BGPR surveys with 100MHz antennas. Seismic tomography enabled the identification of changes in Pwave and S-wave velocity, the Vp/Vs ratio, dynamic Poisson's ratio and dynamic Young's modulus. It was clear that seismic anomalies required verification by other methods. The BGPR survey was performed in a specially designed borehole, passing through the selected seismic anomalies. While the borehole was being drilled, the outflow of gases was identified, with varying amounts of CH4, CO2, and H2S detected, as well as water outflow. The results of BGPR confirmed the location of a reservoir of water and gases, about 30 m in length, found in layer of dolomite. The direct cause of the BGPR anomaly was assumed to be intensive fracturing, a greater content of clay material in the dolomite, and the presence of water in the fractured zone. The BGPR image was correlated with information on lithology, fracturing based on the RQD index and additional information acquired during drilling about water and gases surveys and other symptoms. The achieved results also showed a very strong correlation between the location of the zone containing gases and water and the anomalous S-wave velocity and field of dynamic Poisson?s ratio, and to a lesser extent other seismic parameters. It was found that the other measured seismic anomalies may be of the same nature as those identified in the control borehole and accordingly will require the implementation of detailed identification. The performed tests have also shown the usefulness of geophysical methods to identify geodynamic hazards under the geological and mining conditions of the copper ore deposit in the Rudna mine.

Aug 1, 2013

By Jerry Dolph

Hecla Mining's Lucky Friday Mine, located beneath the town of Mullan, ID, has been shaken since the 1960s by many deep underground rock bursts. The largest rock burst carried a magnitude of 3.5 on the Richter Scale. It occurred in 1969 when all of the stopes on a level approached an upper level at the same elevation. After that, a stair-step pattern was used to give the mine's levels more of an "arch." The article is an account of one of the more ferocious bursts to hit the miners of the Lucky Friday. I say "miners" instead of "mine" because I was there and it was a very personal experience for me. I had been working at the Lucky Friday for six years. During that time, I had heard and felt thousands of air blasts. In fact, in the early spring of 1986, the mine was experiencing as many as 1000 air blasts an hour, of different intensi¬ties, of course. Most of them sounded like popcorn popping. There were also a few bumps and occasionally a real boomer. That day did not seem any different

Jan 1, 1994

By J. O. Lewis, Carl H. Beal

Introduction ............................... 492 Theories Relating to the Recovery of Oil.................. 493 Methods Commonly Employed for the Estimation of Future Production..... 495 Saturation Method........................... 495 Production Curve Method....................... 496 Production per Acre Method.....................: 496 Appraisal Curves.............................. 498 Derivation and Construction...................... 498 Comparison of Appraisal Curves of the Osage and Nowata Fields...... 505 Use of Appraisal Curves........................ 506 Accuracy of the Apprais?l Curves and Their Sources of Error........ 508 Relation Between Future Productions of Wells of Equal Output....... 510 Use of Appraisal Curves for the Derivation of Generalized Future Decline Curves. 513 Theory of Generalized Curves Showing the Decline in Production...... 513 Suggested Methods for Making Closer Estimates.............. 517 Use of Logarithmic Coordinate Paper.................... 518 Summary................................ 520 Introduction Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in production, the rapidity of decline depending on the output of the wells and on other factork governing their productivity. The production curve of a well shows the amount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, will furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property maybe judged, and proper depletion and depreciation charges may be made on' the books of the

Jan 1, 1918

BP Minerals America (BPMA) has completed its $400 million modernization of Kennecott Utah Copper's Bingham Canyon mine. Modernized facilities include the in-pit crusher, conveyor, ore storage area, concentrator, ore pipe-line, and tailings pipeline. With modernization, Kennecott will achieve substantial cost reductions. Bingham Canyon is now one of the lowest cost copper producers in the world. And the mine will continue to provide jobs and income in Utah for another 30 years or more. The Modernization Project began in February 1986. The work took 33 months. In late 1987, the construction force peaked at 1100 workers. Kennecott Utah Copper now employs a permanent work force of 2100 employees. Less equipment and more efficiency The modernization work has increased the scale of the facilities that transport and process copper ore. A large, continuous transport system has replaced multiple haulage units. Fewer but larger pieces of equipment have replaced many crushing, grinding, and flotation units. The result is less maintenance, fewer employees, and improved metal recoveries. About one-third of the $400 million modernization project is directed at improving ore movement by eliminating rail transport. The new concentrator accounts for the remaining two-thirds of the modernization investment. The modernized plant was started up in stages. In February, ore was fed to the crusher. By the end of March, the three grinding lines were operating and the flotation circuit was producing copper concentrate. In July, the design through-put rate of 70 kt/d (77,000 stpd) was reached. October saw the achievement of targeted metal recoveries that corresponded to the fully modernized operation. It is estimated that Bingham Canyon will annually produce 181 kt (200,000 st) of refined copper, 9.3 t (300,000 oz) of gold, 71 t (2.3 million oz) of silver, and 5.4 kt (12 million lb) of molybdenite. Current Bingham Canyon production is about 97 kt/d (107,000 stpd) and a similar amount of overburden. Some 70 kt/d (77,000 stpd) of ore are processed through the in-pit crusher and 27 kt/d (30,000 stpd) of ore are transported by rail. The Bingham Canyon mine has yielded more than 11 Mt (12 million st) of refined copper. In 1863, precious metals - silver-bearing lead - were first discovered in Bingham Canyon. What was once a mountain is now a huge open pit. In fact, the mine is the world's largest man made excavation. The pit is some 4 km (2.5 miles) wide and 0.8 km (0.5 miles) deep. Since the pit began operating in 1906, more than 4.5 Gt (5 billion st) of material have been removed. Modernized facilities Electric 21 m3 (27 cu yd) or 23 m3 (30 cu yd) shovels are used to load the haulage trucks. Both 154 t (170 st) and 181 t (200 st) trucks are used to haul the ore to a mobile, in-pit crusher. The crusher replaces three crushers located at the old concentrators. There are two dumping locations at the new crusher, which can handle two trucks a minute. The 1.5 x 2.7 m (60 x 109 in.), 745 kW (1000 hp) Allis-Chalmers gyratory crusher reduces the ore to 254 mm (10 in.) size or less and delivers it to the conveyor. The crusher and conveyor systems are capable of handling 9 kt/h (10,000 stph) of ore.

Jan 11, 1988

By Jing-she Li, Hai-yan Tang, Cheng-song Liu, Wei Liu

"In order to effectively utilize cheap and low quality iron ores, a hematite ore in a certain steel plant in Xinjiang was researched on to obtain ""iron increase and silicon reduction"" by ore dressing operation experiment and the performance indexes of the hematite ore were optimized. Based on the fundamental characteristics and high-temperature properties of the concentrate after ore dressing and other five kinds of iron ores which were co=only used in this steel plant, ore matching principles were proposed and a sintering ore blending optimization model was established. Finally, sinter pot test was carried out to verify the validity and practicability of the sintering ore blending optimization model which was aimed at giving consideration to the sintering indexes and the cost.IntroductionIn recent years, the price of imported iron ore with high quality is always at a high level, while iron ore self-sufficient rate in China is less than 50%. Enormous market demand and high dependence of domestic enterprises on imported iron ore makes the price of it hardly return to rational. In order to get rid of the situation of long-term meager profit and even deficit, more and more iron and steel enterprises in China transit their focus of reducing production cost to the utilization and development of relatively cheap but low-grade iron ore resources at home[l-4l_ However, besides the disadvantages of low iron grade, high content of impurities and complex embedded properties, the high-temperature properties of iron ore often go beyond the suitable ranges for producing sinter with high quality. Thus directly utilization of this kind of iron ore without ore dressing process would probably affect the metallurgical performance and indexes of sinter ore.Previous research and production practice have shown that traditional iron ore matching in sintering mainly focus on the reasonable collocation of properties of iron ores with low quality and high quality, but pay less attention to ore dressing process of low quality iron ores and matching them with high quality iron ores. Actually, compare with directly utilization, iron ores with low quality after ore dressing have higher suitability for matching with high quality ones which is beneficial to reduce the consumption of iron ores with high quality and control the production cost of sintering [5-s1."

Jan 1, 2014

By Kamran Esmaieli

Open Pit Mining Through Underground Voids: Challenges Main Challenges/Hazards: Unexpected collapse of the pit floor and/or pit walls; The loss of equipment and/or people into underground voids; Loss of explosives from blast holes that broken through into the underground voids. How to address these challenges? An important step that must be integrated into mine planning and design is the accurate detection and delineation of underground voids. (i.e. probe drilling, Geophysical techniques, laser scanning,?); Leaving a pillar of adequate thickness between the working bench and the underground voids; Backfilling the underground voids from surface using vertical or inclined raises; Monitoring the working locations (pit floor and pit slopes) to detect movements.

May 1, 2013

The importance of orebody definition and optimisation in project development cannot be overstated. Inappropriate orebody definition is the single most important reason for project under performance and/or failure. Without the firm foundation of good orebody definition, the structure of a project cannot be assembled reliably. Many factors need to be considered in the process of orebody definition. These factors are well summed up in paragraph 123 of The Institute's Code and Guidelines for Assessment and Valuation of Mineral Assets and Mineral Securities (Valmin Code). The factors range from the initial geological data through assaying, geotechnical and hydrogeological factors to mining and metallurgical considerations. There are other factors which also need to be considered including marketing and environmental factors. This paper briefly reviews some of these factors and their impact on project development. Three examples are presented where one or more of these factors have had significant impact on the development of the Project.

Jan 1, 1997

By Miguel Angel Ibarra

This paper describes the results of a digital computer simulation study in which the impact of the proposed truck dispatching on the overall mine productivity was investigated for an operating open pit mine. In the study, the existing operation was first simulated for a one-month period, using both the actual time study data and the computed cycle times. By adjusting certain input parameters to the simulation program, the actual one month production was first duplicated through simulation. Afterwards, the operation was again simulated in a dispatch mode. Comparison of simulation results under the dispatch mode, with the initial base case simulation results, showed a definite improvement in overall productivity with dispatching; i.e., approximately 10% gain for the operation. As expected, the results also showed that the extent of possible improvement did vary with the particular pit configuration being investigated.

Jan 1, 1980

By M. Sagisaka

Coal is expected as one of the main energy sources for a long period because of vast deposits. However, two large barriers to utilize it are suggested, i.e. the carbon dioxide emissions and ash disposal. The authors chose principal methods and areas to utilize coal ash and analyzed the environmental impacts caused by the ash treatment considering the source of the ash. According to the analysis based on lifecycle thinking, an optimized ash treatment system can reduce the integrated environmental impact. It suggests that coal can carry out its role for several decades without disturbances from the point of ash treatment.

Jan 1, 2006

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the' Bureau's laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949