Search Documents

By P. P. Gregory

NATURAL petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the ``pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the con-trolled methods of production and drilling, a portion of this gas is pro-duced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a-given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grog rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures were increasing.

Jan 1, 1938

By N. A. D. Parlee

THE gas-liquid metal diffusion cell technique1-3 has been used to study the diffusion of nitrogen in Fe-C alloys. The actual apparatus and technique were the same as employed by the authors to study the diffusion of hydrogen in liquid iron.' The diffusion cell' was formed by immersing an alumina tube in a stagnant melt contained in an alumina crucible. The tube (hereafter called absorption tube) contained nitrogen gas at 1 atm and was connected to a sensitive gas-measuring system. The change in the average concentration of nitrogen in the melt in the absorption tube was determined by measuring the rate of absorption of nitrogen in the diffusion cell. Eq. [I], 1-3 derived from the appropriate solution of Fick's second law, was used to examine the data and to calculate chemical diffusion coefficients (D) in situations where the absorption appeared to be controlled by diffusion in the liquid: where V is the stp volume in cu cm, d is the diffusion cell diameter in cm, p, is the density of the melt in g per cu cm, pg is the stp density of nitrogen in g per cu cm, C, is expressed in wt pct, D is in sq cm per sec, and t is in min. According to Eq. [I], a plot of v vs vt should yield a straight line passing through the origin if absorption is controlled by diffusion in the liquid. The slope of this line could be used to determine the value of D under appropriate conditions. As discussed in earlier reports,1,2 the initial thermal expansion of the gas upon immersing the absorption tube distorts the line in the initial stages of a diffusion experiment. However, this is not a serious problem since the slope of V vs 6 plots can be determined from the data points obtained after the initial expansion ceases. The volumes reported on the data plot presented here represent absorption after this thermal expansion ceased. Several preliminary diffusion experiments were attempted with melts of pure iron and with Fe-C alloys containing up to 0.6 pct C. In these cases, no or very little absorption was observed. The only data obtained were for an Fe-C melt which was in addition thoroughly deoxidized by successive hydrogen and vacuum-degassing treatments. These treatments introduced an appreciable amount of aluminum into the melt and reduced its omgen content. The original charge material for this melt contained 0.23 pct s and approximately 0.001 pct &. After repeated hydrogen and vacuum-degassing treatments two diffusion experiments were performed. The analysis of the melt

Jan 1, 1968

By J. Brendan Mclaughlin, Casimir J. Koshinski, Michael V. Rose, Wolfgang Baum

Mercury contamination is a worldwide problem in the mining, smelting, and refining of gold, silver, and copper. In these areas, mercury may be found as a naturally-occurring material in ores and concentrates, and/or in secondary feedstocks such as leach residues, pyrometallurgical treatment residues, refinery by­products, electrowinning electrodes, autoclave discharge solids, and waste water and acid plant sludges. The United States Environmental Protection Agency (EPA) has designated mercury one of the most harmful heavy metal contaminant in the environment and has implemented regulations that prohibit land disposal of characteristically hazardous wastes containing greater than 0.20 mg/1 TCLP mercury without prior treatment, thus increasing the cost of managing these materials. The presence of mercury in mine, smelter, and refinery by­products and wastes severely decreases, and in some cases eliminates, the ability to recover residual metal values from the contaminated material. The lost revenue associated with this disposal, combined with the increased direct cost of waste treatment, and/or disposal and protecting workers and the environment, can adversely affect overall profitability. The safe, efficient, and economical removal of mercury from gold, silver, and copper mining by-products requires a treatment process that is capable of liberating the mercury from the wide variety of compounds and matrices in which it may be contained, reducing the mercury content in the matrix to desired levels, and recovering the mercury in pure saleable form, without producing any secondary solid, liquid, or gaseous wastes. This paper reviews results from commercial operations and pilot scale tests using a thermal process owned and operated by Mercury Recovery Services, Inc. (MRS) to remove and recover mercury from copper acid plant blowdown sludge, Merrill­Crowe precipitate from gold/silver mining operations, and Cottrell and salt slag dusts from a precious metals refinery.

Jan 1, 1997

By T. D. Mueller, F. C. Miller, Jr. Earlougher R. C.

In analyzing pressure buildup tests for field wells producing both oil and gas, the common practice is to use a modification of single-phase flow theory. Validity of such an approximation has been demonstrated for single-well solution-gas-drive systems. This paper indicates that such approximations are also valid for two-well solution-gas'-drive systems. From this it is inferred that the technique can be used for multiple-well systems. A computer was used to simulate the behavior of a two-well solution-gas-drive reservoir to test the validity of the above type of analysis. Simulation results indicate that pressure buildup tests in such a system can be analyzed within engineering accuracy for formation permeability and pressure. A rule of thumb is given for estimating the length of time a well must be shut in for the pressure in a nearby producing well to increase significantly. To observe such an increase, the shut-in well would have to be left shut in much longer than normal. INTRODUCTION An important technique for obtaining data concerning a producing petroleum reservoir is the pressure buildup test. Such a test, when properly conducted and analyzed, provides information on the average reservoir pressure and the permeability in the major drainage area of a well. The theory upon which the analysis of a pressure buildup test is based assumes that the behavior of the fluid in the reservoir is adequately described by the diffusivity equation.1 Use of the diffusivity equation implies that a single fluid of small and constant compressibility is flowing. To analyze a pressure buildup test in situations which involve more than one fluid phase, the single-fluid analysis is extended. This paper verifies the extension of pressure buildup analyses to two-phase, two-well systems. Miller, Dyes and Hutchinson1 have presented a technique for analyzing pressure buildup tests in circular bounded reservoirs. Their method requires that the reservoir be producing at pseudo-steady state (constant pressure gradients) prior to shut-in. An alternate reservoir model, presented by Horner,2 assumes that the reservoir is infinite. The Homer model does not assume a Pseudo-steady state prior to shut-in, but the assumption that the reservoir is infinite implies that the average pressure can be determined only if the total production prior to shut-in is small compared to the total fluid originally present. Limitations imposed by the pseudo-steady state and infinite reservoir assumptions are avoided by the technique proposed by Matthews, Brons and Hazebroek.3 Their method can be used to calculate both the Permeability and the average pressure in bounded single-well systems which are not necessarily at steady state. They also suggested determining the average pressure of a multi-well reservoir producing from pseudo-steady state by volumetrically averaging the static pressures of the individual wells. Matthews and Lefkovits4 used numerical simulation techniques to verify that this method does produce adequate results for single-phase, multiple-well systems. Perrine5 proposed modifications to the single-phase theory so that pressure buildup tests in multiple-phase systems could be analyzed. He suggested replacing the single-phase mobility (k/µ) by the sum of the mobilities of the individual phases, and replacing the fluid compressibility by an average compressibility weighted by the saturations of the separate phases. By using numerical techniques to solve the two-phase flow problem for a single-well system, he concluded that this approximation gives results within engineering accuracy. More recently, Weller6 has shown that, for a gas-oil system with a single well at the center of a circular reservoir, pressure buildup tests can be analyzed adequately by using the modification proposed by Perrine. Feller's results also indicate that, as the gas saturation increases, this analysis becomes less accurate. To date, no evidence is available to show that the Perrine approximations can be combined with the Matthews-Brons-Hazebroek technique to calculate the average pressure of a multi-well,

On the following pages are abstracts of papers published by the Institute during the year 1936 as TECHNICAL PUBLICATIONS and CONTRIBUTIONS, papers in bound volumes appearing for the first time, and papers in MINING AND METALLURGY For abstracts of papers that appeared in bound volumes in 1936 but that were published as TECHNICAL PUBLICATIONS in 1935, see the YEAR BOOK dated January 1936.

Jan 1, 1937

By J P. Tidman, I J. Kirby, G H. Harries

The SABREX computer model is based on the fact that both shock waves and gas pressure are important in describing a blast. The treatment of explosive-rock interactions includes the influence of non-ideal detonation to make use of recent advances in that field. Details of the blast layout are defined from a comprehensive list of conditions the blaster can control (drill pattern, charging and hook-up). The program gives practical and graphic information about fragmentation, muckpile, damage and costs.

Jan 1, 1987

By Fiseha Tesfaye, Pekka Taskinen

"A thermodynamic study of the equilibrium phase assemblage AgBi3S5-Bi2S3-S was made by an EMF-technique, using the RbAg4l5 solid electrolyte. The ternary phase was synthesized from the pure Ag2S and Bi2S3 in an evacuated silica ampoule and grinded into powder and mixed with appropriate compositions of B12S3 and S, in a series of experiments, for pressing in to pellets. The pellets were assembled to form the galvanic cells Pt (-) | Ag ] RbAg4ls | AgBi3S5+ Bi2S3 + S + (C) I Pt (+). The EMF-measurements were made in the temperature range 299 - 460 K.In this paper, thermodynamic functions of the ternary phase AgBi3S5 (pavonite) have been determined. The agreement between the obtained results and the literature values were established.IntroductionThe complex group of ore minerals constitutes from trace amounts to a major proportions of sulfosalts. Although the sulfosalts rarely form massive ore bodies, they are commonly associated with rich sulfide ore minerals for the base and precious metals and widely distributed in a metal poor sulfide minerals [1]. For instance, Ag-bearing sulfosalts are encountered in ore minerals for the production of the base metals and are common sources of silver. Nevertheless, thermodynamic properties of the sulfosalts are poorly known.Reliable thermochemical data are essential for quantitative modeling of the chemical behavior of the sulfosalts in equilibrium with sulfides, which in turn would promote the optimization of complex minerals treatment and extractive metallurgy of the valuable metals."

Jan 1, 2012

By D. B. Taliaferro, David M. Logan

which an operator may obtain detailed information regarding all projects in the State. It is the purpose of this report to present data such as volume of oil produced monthly, volume of water injected monthly, spacing of wells, number of injection wells and oil wells, and other such pertinent information regarding every project in the State whether active or abandoned and whether a success or a failure. It is believed that with these data it is possible to analyze water-flooding operations in this area more completely than has been possible in the past. As the title indicates, the report is essentially a history, and ordinarily no opinion is given as to the cause for the success or failure of individual projects. Increasing the production of oil is exceedingly important at this time, and one method by which it may be done most readily is by providing additional energy for the movement of oil in many of the older fields. In many oil fields the predominant force that drives oil through the porus reservoir rocks to wells is the gas dissolved in or otherwise associated with the oil under pressure. As the pressure in the reservoir declines in consequence of the removal of fluid, gas comes out of solution in the form of minute bubbles; as the pressure is reduced further, the expansion of these bubbles forces part of the oil toward the areas of lowest pressure and into the producing wells. The physical properties of the oil and the gas governing their flow through reservoir rocks to wells differ, and much of the gas slips past the oil leaving large quantities of oil in the reservoir when the pressure has been exhausted. Often the natural productive life of fields is prolonged by reducing the pressure in oil wells below atmospheric with vacuum pumps; but the ad- ditional energy made available in this manner is limited to less than 1 atmos- phere of pressure, and even after the extended application of "vacuum" to a petroleum reservoir large quantities of oil are left unrecovered in the porous rocks and sands.

Nov 1, 1943

By H. F. King

In 1982, the result of a 3-year study was published as "A Guide to the Understanding of Ore Reserve Estimation". The principal conclusions were that computation formed only part, and perhaps not the most important part, of an estimate and that the estimate should recognize that geological, mining engineering and metallurgical judgements formed an essential part of the eventual result. Subsequent expectation/realization studies of several mines have produced case histories which form the principal basis of the paper. These imply that geology is even a larger factor than thought earlier.

Jan 1, 1985

By R. W. Fountain, W. D. Forgeng

A new constitutional diagram is presented for the cobalt-rich end of the cobalt-titaniurn system. The modifications result from the presence of a new, intermediate, fcc phase, ?, the existence and homogeneity limits of which were established by metallo-graphic and X-ray studies of alloys containing from about 3 to 30 pct Ti. The precipitation of the ? phase from supersaturated solid solution was studied by hardness and electrical resistivity measzsrements, and two distinct stages in the process were observed. COBALT forms the base for a number of precipitation -hardenable alloy systems which may be divided into two distinct categories of practical interest, a) those hardened by intermetallic compounds and b) those hardened by carbide formation. The precipitation of intermetallic compounds from solid solution in cobalt-rich alloys has, however, received very little attention. Although the phase diagrams for some binary systems capable of precipitation have been determined,' there is an almost complete lack of data on the property changes associated with the precipitation, and even less information on the kinetics of the reactions or morphology of the products. More information is available on the precipitation of carbides because of the practical significance in superalloys. A survey of cobalt binary phase diagrams suggested that the cobalt-titanium alloys might provide interesting and useful precipitation-hardenable alloys. The equilibrium diagram as proposed by Wallbaum2 is shown in Fig. 1. Köster and wagner3 have indicated that the maximum solubility of titanium in cobalt is about 10 pct at the eutectic temperature (1135oC), and this decreases to about 7.2 pct at room temperature. The temperature of the allotropic transformation in cobalt is lowered by the addition of titanium, about 5 pct being sufficient to retain the high-temperature fcc modification to room temperature. Wallbaum and Witte 4,5 have indicated that the precipitating phase in alloys containing up to about 29 pct Ti is Co2Ti, a hexagonal Laves phase of the MgNi, type. With slightly higher titanium contents, they also report a cubic modification of Co2Ti of the MgCu2-type Laves phase. Duwez and Taylor6 confirmed the existence of the hexagonal (MgNi2) modification but not the cubic (MgCuz) modification of Co2Ti and suggested that existence of the cubic form may have resulted from impurities in Wallbaum's alloys. In their work on Laves-type phases, Elliott and Rostoker 7 reported the cubic modification of Co,Ti, but did not confirm the existence of the hexagonal modification. However, Dwight8 in a discussion of the work of Eliott and Rostoker again showed the existence of both modifications of Co2Ti, a result which was confirmed at that time by Elliott and Rostoker. As a result of a study on the iron-cobalt-titanium system, Köster and Gellers suggested the existence of a Co3Ti phase isomorphous with Fe3Ti. Witte and Wallbaum,' however, established the fact that no compound, Fe3Ti, exists in the iron-titanium system, and in a later publication, wallbaum2 stated that Kitster and Geller's reasoning was not valid, and no compound, Co3Ti, exists. This conclusion was later acknowledged by Köster.10 Preliminary experiments by the present authors to determine the precipitation-hardening characteristics of the cobalt-rich, cobalt-titanium alloys re-

Jan 1, 1960

By Camila Mendonça Romero Sales

Este trabalho teve como objetivo observar o percentual de transformação das fases (romboédrica e hexagonal), após tratamento termobárico do hidrocarboneto aromático Antraceno. As amostras foram tratadas sob pressão fixada em 4,5GPa e temperatura variando entre 900 e 1300°C, com o intuito de obter estruturas grafíticas. O percentual de fases foi obtido a partir de dados de difração de Raios X e através de refinamento pelo método de Rietveld, sendo que na temperatura de 1300°C foi possível observar um aumento na fase romboédrica e melhores parâmetros de refinamento. Pode-se concluir que o Antraceno ao ser submetido a altas temperaturas e alta pressão torna possível o aumento da fase romboédrica do material grafítico, o que resulta em melhores condições de síntese do diamante.

Aug 16, 2017

By M. D. Vilarinho, W. Xuan, F. Vasconcelos Guimarães

"This article summarises the efforts to reduce the energy consumption in grinding in a magnetite ore beneficiation plant. ArcelorMittal Kryvyi Rih ore beneficiation plant produces magnetite concentrate at 65% Fe and 8% SiO2, of which the D80 is approximately 44µm after three stages of grinding with ball mills and magnetic separation. Characterisation and laboratory scale bench tests performed on samples from the beneficiation plant indicate that the industrial flowsheet could be simplified. After the first stage of grinding and magnetic separation, a significant size fraction of the intermediate concentrate is already well liberated. Therefore, it can be directly concentrated in a second stage magnetic separation without further grinding. If a screen of 150µm size can be implemented after the first stage of grinding-magnetic separation, only the oversize of screening, representing 35% of the material, requires secondary and tertiary grinding and magnetic separation. The combined concentrate from the two fractions already meets the industrial specifications. This new route can provide the same final product, with fewer mills; it saves around 30% in energy consumption only in the grinding step without changing the main structures of the processing plant.INTRODUCTION Comminution, including crushing and grinding, is responsible for at least 40% of total energy usage in mining and mineral processing. This paper shows an example to reduce grinding cost, by changing the flow sheet design strategy in ArcelorMittal Kryvyi Rih (AMKR).AMKR is one of the most important mining and steel complexes in Krivoy Rog basin in Ukraine, which has been studied over 100 years because of mining of iron ores. The iron ores are associated to Banded Iron Formation of the Saksagan suite, with an average iron grade of around 36 percent Fe. The total thickness of the Krivoy Rog Supergroup reaches 5-6 km, whereas that of the iron-ore Saksagan Group comprises up to 1400 m. High-grade iron ore extends to more than 2,000 m below present surface"

Jan 1, 2018

By Edwards R

Greater efficiency of capture of minus 6 mm to fine micron size particles of free gold is achieved with the Knelson Concentrator. The development, principles of operation and recent innovations relating to this enhanced gravity concentrating device are described by the inventor, followed by a description of application and consequent economic benefits in low grade alluvial gold deposits by a large scale user of Knelson Concentrators in the Northern Territory of Australia.

Jan 1, 1990

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By J. B. Yianatos, G. S. Dobby, J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

The question is posed as to why columns typically have a collection zone 10 m high (H) by 1 m in diameter (D). Three geometry dependent factors are considered: degree of mixing, Np; volumetric bias rate, B; and volumetric gas rate, G. Increasing H:D decreased Np and B, which improves performance but decreases G, which causes the column to approach overloading. Taking typical column operating conditions, it is concluded that a collection zone H:D of 10:l is a reasonable compromise.

Jan 1, 1987

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

The steady-state operation of an isothermal, counter-current reactor in which a mouing bed of hematite particles is reduced by hydrogen has been modeled mathematically using a generalized single-particle kinetic formulation for topochemical reduction with formation of the intermediate oxides, wustite and magnetite. Reduction prof iles have been generated for various oper- REDUCTION of iron ore, as practiced industrially, approaches counter current, granular-bed operation. The total process is extremely complex. Quite under- ating conditions selected to demonstrate the influence of major variables such as gas and solid flow rates, bed length, and particle size. These profiles illustrate , among other things, that the reducing-gas requirement in a countercurrent bed hinges upon the iron-wüstite equilibrium or 'pinch-point" in much the same way as in a staged reactor. standably, nearly all research has been focused on reduction of single particles of oxide under controlled conditions. While this approach simplifies the problem by eliminating interparticle interactions, the remaining intraparticle transport and kinetic processes still constitute a most formidable challenge. Only within the last few years has knowledge of single-particle reactions been developed sufficiently to make modeling of counter current-bed reduction a realistic and useful study of process behavior. The authors have analyzed1"3 extensive laboratory

Jan 1, 1969

By K. Potluri, S. Akella, S. Bhansali

"This paper presents the design and angular strength analysis of microneedles for use as a transdermal interface for drug delivery, fluid analysis and sampling etc. Microneedles of different dimensions were designed and fabricated using various materials viz. Si02, OxideNitride- Oxide (O-N-0). The design, modeling and analysis was done using the Finite Element Analysis (FEA) software ANSYS™ 6.1. Angular strength analysis of the microneedles was done using angular loading in ANSYS™, with the corresponding inaterial property settings. Using the force-displacement settings, forces of magnitudes in the range of 10 mN - 25 mN were applied on the microneedles at loading angles ranging from 30° to 90° was applied on needles. Square and circular shaped microneedles were modeled and the displacements and stresses generated were studied to characterize the angular strength of the microneedles. The buckling and force-displacement analyses show that O-N-O microneedles are more strong and robust as compared to needles of other materials. The analysis shows that while circular microneedles have uniform stress distribution, square microneedles have low stresses concentrated along the edges.INTRODUCTIONIn modem clinical and biomedical applications, drug delivery is done either by oral administration or by hypodermic injection. Hypodermic injection of drugs using needles is often painful. Hence, transdermal drug delivery techniques are increasingly being sought out as an alternative. In transdermal drug delivery the needles puncture the Stratum comeurn - the outermost layer of the human skin. The advantage of transdermal drug delivery (or transdermal measurement) technique, is that it reduces pain and tissue trauma."

Jan 1, 2004

By Paul T. Allsman, Paul F. Yopes

17.1--CURRENT AND FUTURE STATUS OF SURFACE MINING PAUL T. ALLSMAN AND PAUL F. YOPES 17.1.1--CURRENT The history of surface mining essentially is one of mining coal, copper, iron and aluminum ores, of placer mining gold and tin, and of pits and quarries producing clays, gypsum, phosphate rock, sand, gravel and stone. Table 17-1 is a summary of the estimated world and United States production of crude metallic and non¬metallic ores and coal in 1969. It includes estimates of the quantities produced by surface-mining methods. Two-thirds of the 10 billion tons are mined from the surface, ranging from a third of the coal. 57% of the metallic ores, and nearly all clays, stone, sand and gravel. Production by surface methods in the United States, parallels that of the world with one exception: about 90% of the copper and iron ore is mined from the surface, whereas elsewhere only about half the copper ore is surface mined. In Canada, surface mining of the Athabasca tar-sand deposits is a recent large-scale unique operation. In surface mining of coal and, to a lesser extent, metallic ores, much waste is stripped, but in nonmetallic pits and quarries the ratio between waste and ore usually is small. Assuming that the stripping ratio for surface mining in the

Jan 1, 1973

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

By Seong-Jong Kim

The formation behavior and corrosion characteristics of anodic oxide films on pure Mg and Mg-AI alloys were investigated focusing on the effects of anodizing potential, Al content, temperature and NaOH concentration. Pure Mg and Mg-AI alloys were anodized for 10 min at 3, 10, 40, and 80 V in NaOH solutions. Mg(OH)2 was generated by an active dissolution reaction at the surface of the specimen and the product was affected by temperature while MgO generation increased with NaOH concentration. Moreover, the current density after anodizing for 10 min at a constant potential decreased with increasing AI content in Mg-AI alloys,

Jan 1, 2003