Search Documents

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By R. S. Shoemaker, F. W. McQuiston

Mineral Occurrence Treatment Method Table Page

Jan 1, 1975

By N. F. LeJeune

For a number of years the Bureau of mines has conducted semi-annual surveys to determine the changes in the characteristics of the motor gasoline being sold in the United States. The Bureau of Mines surveys, from April, 1917, to January, 1943, indicated a progressive decrease in the end point range. The survey for July, 1923 showed an interruption in this progressive decrease. This interruption, as shown in Table 1, in the line marked "Difference," was apparently a definite one, for the data obtained in the surveys of July, 19233, January, 19244, and the present one, apparently substantiate it. The figures in Table 1 were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points and the 10 per cent having the lowest end points were grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10 per cent" and the ?Maximum 10 per cent," respectively. The same scheme was used on the succeeding surveys.

Jan 1, 1924

Jan 1, 1949

Jan 1, 1944

Jan 1, 1946

Jan 1, 1947

By Fred M. Phillips

Jan 1, 1985

By B. Yarar

Jan 1, 1985

By Clement K. Chase, George M. Potter

Copper dump and heap leaching operations are conducted worldwide for production of substantial amounts of copper Such dumps and heaps contain appreciable amounts of other potentially valuable elements such as gold, Iron, magnesium, manganese, molybdenum, silver, titanium, and uranium. Except for uranium, recovery of these elements has not been attempted to any significant extent However, such recovery merits attention based upon availability of existing chemical techniques. This paper presents some thoughts on possible techniques together with opportunities for commercial applications.

Jan 1, 1983

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By Vahid Javaheri, David Porter, Tun Tun Nyo

A field emission scanning electron microscope equipped with EBSD has been employed to evaluate the role of 0.013 wt% Nb on the evolution of the microstructure and texture of a novel thermomechanically processed low-alloy, medium-carbon steel. Specimens were subjected to hot-rolling with a total reduction of 80%, four passes in the recrystallization regime and four passes below the non-recrystallization temperature. Immediately after rolling, the strips were quenched to 420 °C and subsequently cooled slowly in a furnace to simulate strip coiling with transformation of austenite to bainite. The results showed that Nb microalloying results in a finer microstructure with a sharper texture when compared to an identical steel but without Nb. In addition, analysis of the retained austenite texture indicated that the main bcc texture components are the product transformed brass and copper components in the parent austenite.

Mar 1, 2018

By A. K. Riihimäki

The description deals with duplex stainless cast steels and austenitic high molybdenum steels used in pumps for severe condition service. The main modem nitrogen alloyed duplex cast steels are presented in the ASTM standard A-890. Two grades of high molybdenum austenitic stainless steels there are presented in ASTM A-744 (-96) standard i.e. CN-3MN and CK-3MCuN. The latest and most corrosion- resistant stainless steel grade is AVESTA 654 SMO?. Avesta Sheffield the trademark owner has granted Ahlstrom Pumps license to produce the material. This new stainless steel as pump material for severe service has improved properties in the hydrometallurgy and electrorefining processes of metal and especially in the copper industry compared to duplex stainless steels. The paper deals briefly with the foundry process to manufacture high alloy stainless steel pump castings. The AOD-method (AOD= Argon Oxygen Decarburization) is an important prerequisite for the melting of low carbon, high chromium and molybdenum alloyed nitrogen steels. The properties of these steels are included. The main topic is the corrosion resistance of the above-mentioned pump materials in severe service. Results of short-time erosion and corrosion tests are discussed and compared with the results of plant tests. Practical results of pump materials performance in severe service for the copper industry are given. The new high alloyed cast stainless steel (main elements; Cr-24%, Ni-22%, Mo-7,3% and N-0,5%) has shown improved corrosion and erosion properties as process pump material in several severe service applications e.g. in the metal industry.

Jan 1, 1999

By D. L. Madge

The text of this chapter was not received in time for printing.

Jan 1, 1979

By Manuel Arellano Ramírez

El presente trabajo refiere el proceso de construcción del primer complejo minero metalúrgico del Perú, la empresa Cerro Verde de Arequipa. Para ello, se revisan los antecedentes históricos, participación, financiación, inversión, organización y personal actual, producción y costos directos de operación, plantas y procesamiento, infraestructura e instalaciones auxliares, operaciones y desarrollo regional del proyecto minero.

Nov 20, 1978

By S Sondashi, F. J. Chidley, W. A. Grobler

Some of the challenges facing the flotation of base metal sulphides are the opening of new and varying ore bodies as well as maintaining essential skills in plants. Flotation reagent research focuses not only on improving flotation grade and recovery, but also on producing reagents robust enough to cope with changes. A group of recently developed co-collectors, activators, depressants and frothers are described together with a summary of results measured on base metal sulphide ores.

Jan 1, 2005

By D. Butler

Lateral density changes in the subsurface cause a change in the vertical pull of gravity at the surface. By very accurate measurement of gravity and the practical application of common sense, a microgravity survey can sometimes detect natural or man-made voids, bedrock profiles, and geologic structures of engineering interest. This paper will give some practical guidelines for the application of microgravity surveying. Emphasis in many papers (Blizkovsky, 1979, Fajklewicz, 1983) has been on the anomaly size: herein emphasis will be placed on detectability and signal-to-noise ratios. First, some easy to use curves for anomaly valuation are adapted from Arzi (1974). Secondly, the predictable noise sources are discussed. Thirdly, representative models of abandoned underground workings are evaluated for microgravity surveying given the probable noise in the survey results.

Jan 1, 1988

By V. A. L. Breguncci, A. H. Martins, C. P. Ribeiro Jr.

This work presents experimental results for the recovery of gold present in alkaline cyanide solutions by using the electroelution technique of strong-base anionic polymeric resins IRA 402-CL from Rhom and Haas-Brazil Ltd. loaded with gold. This technique of electroelution of anionic polymeric resins is based on the removal of metal ions adsorbed to the resin, resulting from a potential difference applied between the cathode and anode in an electrolytic cell. The electrolytic cell was composed of an aqueous solution with suitable chemical characteristics and an anionic polymeric resin bed loaded with gold. The resin used in the experiments was loaded using synthetic alkaline gold cyanide solution with 1.0 g/L of gold. The variables studied were electroelution time, cathode current density, distance between cathode and anode and the electrolyte chemical composition. Statistical methods made it possible to establish the optimum conditions that would achieve satisfactory gold recoveries by the electroelution technique. The statistically predicted response for the resin loaded with gold by percolation was 16.5% gold recovery, 2.0 A/m2 cathode current density, 20-mm distance between electrodes and 6.0 hrs electroelution time. For the centrifuging system, the statistically predicted response was 7.41% gold recovery under the following conditions: 0.25 A/m2 cathode current density, 1-mm distance between electrodes, 3.5 hrs electroelution time and 10.9% NaOH in the electrolyte chemical composition.

Jan 1, 2002

By R. L. Smith, J. L. Rutherford

ZONE refining, as developed by W. G. Pfann,1 has been used extensively for the purification of semiconductors. This method has made it possible to obtain the extremely high purity material necessary for the transistor industry. It has also been utilized to some extent for the purification of relatively low-melting-point metals. However, very little attention has been given to reactive, high-melting-point materials, with the exception of silicon. For this element, it has been necessary to use the floating zone technique in order to avoid contamination from the crucible containing the melt. The method is one in which a narrow molten zone is formed in a vertical rod by induction heating. The molten zone is supported between the two solid sections of the rod by surface tension. It is then moved longitudinally along the rod in order to effect a redistribution of solute. This technique has an advantage over the horizontal boat method, since crucible contamination is avoided. It has the disadvantage of being a much more difficult technique than zone refining in a crucible. Furthermore, it is necessarily a slow process, since only one zone at a time can be formed. However, the floating zone process offers a means of obtaining high-purity metals that are either not available, or can only be obtained in powder or pellet form as the result of complex chemical or electrochemical methods. It should be emphasized that the process is not effective in removing all impurity elements. Those that cannot be redistributed in an ingot during zone melting must be removed by some other means. Very little is known of the prope~ties of very high purity reactive metals such as iron, titanium, zirconium, beryllium, etc. It is quite likely that trace elements in such metals can affect their properties drastically. Therefore, one of the primary objectives of this work is to study the properties of metals which have been obtained in the purest form available and then zone refined. Trace elements can be introduced in a variety of ways, such as by inserting wafers between solid portions of the ingot to be melted, by placing the

Jan 1, 1958