Search Documents

The Diamond mechanical soot blower system, manufactured by the Power Specialty Co., Detroit, Mich., consists of a permanent installation of units arranged in groups to fit the design of the various boilers to which they are attached. The units are so arranged as to effect the cleaning of the fire surfaces of the boiler, particularly the tubes, by means of steam jets. When this steam is released among the tubes at a velocity of approximately 2700 ft. per sec. (assuming a pressure of 150 lb.), a perfect whirlwind of currents is created, reaching all the nooks and crannies of the boiler, and thoroughly removing the particles of soot and fine-ash accumulation. This operation requires but a moment's time-from 20 to 50 sec. per unit¬and is performed from two to four times a day, while the boiler is under full load, using a greatly decreased amount of steam and labor as compared with the hand hose or any other system of blowing. Moreover, this cleaning is effected without admitting air, with its cooling effects, to the boiler setting. The Diamond model "G" blower consists of five principal elements as follows: 1. A head through which the steam passes from the main supply line when the valve is opened. The head is the foundation element to which the other elements are attached. 2. A wall box which is bricked into the setting. The box supports the unit, and is so constructed that the blower can be turned freely without admitting air to the inside of the setting. 3. A blower element running cross-wise of the bank of tubes, and consisting of a small header with nozzles so placed as to discharge steam between the boiler tubes. 4. A sheave or hand wheel by means of which the blower element is rotated. 5. Bearings attached to the boiler tubes which support the blower element and permit it to revolve freely. The nozzles from which the steam issues are designed on the principle of the Venturi tube, and vary in design for different pressures. The expanding walls of the Venturi nozzle increase the velocity of the steam over 200 per cent., as compared with a nozzle having a straight orifice. Thus, the velocity of the steam issuing from a straight nozzle at 150 lb. pressure is 912 ft. per sec., whereas, at this pressure the velocity of the steam issuing from a Diamond Venturi nozzle is 2795 ft. per second.

Jan 5, 1918

By V. F. Hollister

Four conditions are commonly accepted as being needed for the development of native sulphur deposits in sedimentary rocks : (1) ample sulphate-bearing evaporite, normally anhydritic; (2) proximity to petroleum deposits; (3) a hydrodynamic system of communication between these two; (4) a stratigraphic or structural trap to prevent escape of the sulphur and sulphur -bearing reaction products. When any of these requisites are absent, apparently no significant residual bio-epigenetic sulphur deposit will form. These requirements are, however, satisfied in some areas, which include both the Triassic and Devonian evaporites of northeastern British Columbia.

Jan 1, 1977

By M. E. Lombardi

THE cost of maintaining the production of an operating oil company is one of the most important, as well as one of the most difficult to estimate, of the various items which go to make up the total cost of producing oil. In the opinion of many operators the cost of drilling and developing new wells, whose production takes the place of the loss in production through decreased yield of the old wells, is considered an operating expense, for the reason that the total income-producing power of the property is not increased. The cost of these new wells may be added directly to production expense, or it may he charged to capital account, and this account depreciated to the same extent. In either case, after an oil company is on a satisfactory income-producing basis, the money for drilling new wells to maintain production must be taken from the income of the company. Three factors determine the cost of maintaining production: First, the rate of decline in yield of the wells; second, the cost of drilling and equipping new wells in terms of their production; third, the decrease in initial production of new wells as the property is drilled and gas pressure taken off the sands, etc. In order to check theoretical figures for the cost of maintaining production the writer, with the assistance of Reed Bush and Fred Tough, has compiled the following figures. It is necessary first of all to choose a period of time during which production for the field or territory studied remains fairly constant. The longer the period of time over which this condition prevails, the better. It is also necessary to eliminate or allow for any extraneous condition which may have affected the production returns, such as the shutting clown of a large number of wells, the bringing in of a well of exceptionally large yield, the opening up of virgin territory where the flush yield is greater than will he had from new wells in after years, etc.

Jan 9, 1915

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

By R. S. French, W. R. Hibbard

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

By B. D. Cullity, J. T. Norton, M. Telkes

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

By B. K. Mishra

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills (14-18 ft). DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important factors such as the configuration of the liner and the geometry of the lifting surfaces are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill with particular emphasis to large diameter mills.

Jan 1, 1992

By Lisa J. Renaud

For generations, the mining industry has been committed to work toward developing new technology that can improve safety and increase production. Now with a more environmentally conscious society and tighter environmental regulations, a natural progression for the industry is to develop and take-on ?green? or environmentally friendly technologies. Not only could this improve the sustainability of operations, but could also reduce the long-term environmental impact footprint that is left behind. Algae represent a new frontier in research and development. As discussed specifically in this paper, algae, specifically microalgae, can be used for the production of biodiesel and other green chemicals by exploiting carbon dioxide and waste heat contained within process off-gasses. The potential positive benefits of this approach in terms of contribution to community and the environment are significant, and the focus of our research and development on microalgae production technology.

Oct 1, 2010

By Karl C. Dean

The Bureau of Mines studied the precipitation of copper from dilute acidic sulfate solutions using shredded automobile scrap in a rotary drum. The tests established that the scrap in the rotary drum precipitated copper faster and more completely than shredded, detinned, tinplate scrap in a launder, with comparable iron consumption. Although power is required to rotate the drum, the faster precipitation and continuous recovery of cement copper are advantages of the tumbler method. Cost evaluation indicates that the rotary drum method, which uses relatively low-cost and readily available shredded automobile scrap, is competitive with the launder method, which uses relatively high-cost shredded tinplate scrap or detinned shredded cans.

Jan 1, 1968

By R. V. Ramani, A. S. C. Owili-eger

The rapid depletion of shallower coal reserves dictate that mining in the future will be deeper and more complex with more difficult natural conditions. Consequently, an increase in methane emission is expected. It is becoming evident that more accurate predictions and better planning are necessary to design efficient methane drainage systems. This objective can be achieved by the utilization of the knowledge of the physics of gas flow through coal seams and rock strata and by the application of digital computers in the solution of methane flow problems. Although the methane emission models described here have not been adequately applied to existing field operations, good agreement between actual field measurements reported in literature and the simulation results indicates the potential of these models for initial flow quantity approximations and ventilation planning. This report has, therefore, introduced to the mine operator yet another application of computers as a planning tool. AREAS FOR FURTHER RESEARCH The study reported here is by no means complete. Extensive research efforts should be directed to the following areas: (a) Better understanding of the physics of gas flow through porous media which exhibit fracture permeability. (b) Determination of field parameters which control gas migration. (c) Investigation of the effects of the rate of penetration on the emission rate and fracture propagation.

Jan 1, 1974

By B. P. Christos

The improved rate of stope-face advance at Buffelsfontein Gold Mining Company Limited by B. P. CHRISTOS (Associate) To achieve a higher rate of stope-face advance. it was necessary to examine al.1aspects of the stoping operation, to identify bottlenecks, and to eliminate them or reduce their effect. The cleaning cycle was fund to be the most significant bottleneck. and this problem was aggravated by long panel lengths. under-capacity winches In strike gullies. and excessively long strike scraping distances.

Jan 12, 1975

By Lloyd A. Morley

To reduce safety and production problems, it is essential that the electrical operating characteristics of coal mining equipment and their electrical subsystems be clearly understood. The Bureau of Mines and the Pennsylvania State University have developed techniques to monitor and analyze several of the critical parameters. A unique system for measuring traction locomotive consumption at the machine has been assembled and utilized. Conclusions from 27 continuous miners show that voltage levels are directly tied to machine efficiency. The Bureau of Mines and Pennsylvania State University, along with West Virginia University, are currently monitoring and accessing mine power transients. Results exhibit that voltage transients of three to five times the line -to-line value are common on underground distribution systems.

Jan 1, 1975

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By Paul A. Hodges

With plant start-up slated for early 1966, Palabora Mining Co. will take its place among the large copper mining properties of the World. Located near the town of Phalaborwa in the Lowveld area of Transvaal Province, approximately 250 air miles northeast of Johannesburg, Palabora is the result of a cooperative project between Rio Tinto-Zinc Corp. and Newmont Mining Co. Other large shareholders are American Metal Climax, Inc., Union Corp. Ltd., and Selection Trust Ltd. Earliest known mining activity in the area is thought to date back about 400 years, when the Bantu tribes were migrating southward from the great lakes of Central Africa. Old workings and hand tools have been found in numerous places on the flanks of Loolekop, the hill that contains the outcrop of the Palabora orebody. Nearby ruins of small furnaces give added evidence of the knowledge of copper smelting possessed by these natives.

Jan 3, 1966

By Mario Samamé Boggio

El presente texto describe los recursos minerales encontrados en la provincia y distrito minero de Hualcayoc en Cajamarca. El distrito ha producido menas de plata y oro durante la Colonia y menas de cobre, zinc y plomo en la actualidad. La plata se incluye en la galena y en la tetraedrita. Algunas vetas contienen cantidades menores de enargita, estibina, jamesonita, boulangeritá y bournonita. La baritina es la ganga principal. También se encuentran: marcasita, pirrotina, rodocrosita, dolomita y calcita. La plata nativa encontrada en la época colonial ya no se encuentra.

Jul 1, 1983

Chlorine as a lixiviant for gold possesses a number of significant chemical and Idnetic advantages over cyanide but because of its corrosive and vaporous nature the method of implementation needs to be significantly modified. At comparable reagent concentrations the dissolution rate for gold in the C12/Cl- systems is some 10 - 100 times that achieved in the 02/CN system. The dissolution rate in the chlorine system is largely a function of the concentration of C12, Cl- and pH. Under conditions of low Cl', (less than 50 g/1), the dissolution rate begins to drop off dramatically over the pH range from 3 - 4. Increasing the level of dissolved chloride ions shifts the pH of this rate reduction to around pH 5 at 100 g/l NaCl, and to around pH 6 at 300 g/l NaCl.

Jan 1, 1991

By D. G. Krige

Discussion by D.G. Krige I read the paper "The jackknife approach" with interest. There appears to be a widespread misunderstanding of the kriging variance as a measure of the error variance of the kriged grade estimate of an ore block. Virtually all mineral deposits display skew frequency distributions and are subject to the well-known proportional effect. Thus, it is usual to find in an ore body, when subdivided a really into subpopulations, that the variances of the grades (or the total sills of the variograms) for the subpopulations will be correlated with the corresponding mean grades (usually linearly with the squares of the mean grades). Thus, the variogram will be station. When this feature is evident, the relative variograms for the subpopulations (i.e., with variogram values divided by the relevant mean squared) will be similar, or they could even be accepted at an averaged model for the whole ore body with stationarity. Using this approach, the kriging variance will reflect the relative error variance that is to be multiplied by the kriged block grade estimate squared to yield the usual kriging variance for purposes of confidential limits. The objection that the kriging variance does not take into account the local grades used for a block valuation then falls away. In the example given by the authors, the global mean grade is not recorded. But the global variance, taken at the value of the total sill, is 0.005, whereas the variance of the 11 values used in the example is 0.000152. The two variances differ by a factor of nearly six. If the relative variogram approach is applicable in this case, the need for a jackknife technique will fall away. Also note that, for skew distributions, the confidence limits for ore-block estimates will be skew as well, and symmetrical normal limits will not apply. RepIy by G.S. Adisoma and M.G. Hester There are a few interesting ways to utilize the block-by-block kriging variance that the authors have encountered. One of them is to classify a particular block into a proven-probable reserve or a possible-resource category, using a somewhat subjectively determined kriging variance value. Here, the kriging variance still represents the drilling density, i.e., data configuration more than the data values. Professor Krige mentions another ingenious approach through the use of relative variograms. This will yield a block kriging variance that takes into account local (block) grade, as he correctly points out, for purposes of confidence limits. However, we are more interested in quantifying the uncertainties associated with grade estimation in a much larger scale than a block. e.g., for a mining phase or the minable reserve. The jackknife, through the block kriging shortcut, provides a simple solution to obtain a single estimation variance for a general shape. The authors' main reference discusses different ways to handle skewed distributions typical in mineral resource estimation, e.g., the weighted jackknife approach or data transformation. Also, as with any technique, we can always improve our estimate by subdividing into smaller populations that are geologically and statistically separate domains. As we have mentioned; the jackknife is but a tool in our collection of tools to solve estimation problems. The jackknife's appeals are its simplicity and versatility. It is handy when no other solution is available, or when the available solution is not practical. It is used with other methods, not to replace them altogether. ?

Jan 1, 1997

By R. A. Isberg, D. A. Parrish, H. Kramer

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75% coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 3, 1981

By John V. Beall

They came from Paris, Washington and Rabat; two directors, two chief geologists and the president of our own local subsidiary company. Such a meeting was not unprecedented, but it seeemed to us that our president was overzealous in arranging for inspections of each exploration site. One was a problem. Jacques, our president, had concocted the idea that we should lead this learned, mature (not exactly aged) group into the desert to see newly found anomaly. It was in virgin country and had been marked by dropping a flour sack on it from the air.

Jan 1, 1971

By Robert Forsyth

IN working the Bessemer process, the bottom of the converter has always been a source of trouble and annoyance, and the subject of more experiments, probably, than any other part of the complex mechanism called a Bessemer plant. This will not appear remark- able when the duties this important piece of refractory material has to perform are taken into consideration. In the first place, by means of the tuyeres, it delivers at a high pressure the air necessary for the conversion of the bath of metal, and has then to resist the intense

Jan 1, 1876