Search Documents

By Charles S. Ney

"THE WRITER'S acquaintance with Kootenay King mine is limited to a brief geological excursion in the vicinity. This paper has been compiled largely from maps of J. Sullivan, mine geologist in 1952, kindly made available to the writer by Transcontinental Resources; a 1942 private report by W. L. Brown; and personal communications with J. Sullivan. Remarks on regional geology, and the comparison with Sullivan mine, are specifically the writer's.The Kootenay King mine is situated in the westernmost range of the southern Canadian Rockies at an elevation of 7,300 feet. From the Sullivan Mine at Kimberley, B. C., it lies 19 miles due east. Six miles of this distance are represented by the pronounced topographical and structural gap of the Rocky Mountain Trench. Mineral claims were locat-ed in the area prior to 1898. The deposit was first seriously explored in the late 1920s, and a small orebody was then outlined and developed. Mining and milling were undertaken in 1951.52. The orebody, amounting to about 14,000 tons, was mined out, and no significant new ore was revealed.The orebody is a replacement of dolomitic argillite by fine-grained galena, sphalerite, and pyrite. The sulphides are finely laminated in the direction of bedding, following out minor folds faithfully. The grade of ore estimated from diamond drill holes (W. L. Brown, 1942) was 11 ·I per cent zinc, 11 ·I per cent lead, and 3·8 ounces per ton of silver. The mineralized zone extends about 250 feet horizontally, 160 feet vertically, with a width of six to twenty feet.General GeologyThe country rocks are sediments of the Aldridge formation of late Precambrian age. For several thousand feet stratigraphically above and below the mine, the formation consists mainly of thinly laminated argillite and siltstone. Several horizons contain appreciable carbonate. About 2,800 feet stratigraphically below the mine, predominantly dolomitic beds mark the top of the underlying Fort Steele formation. The medium-bedded fine quartzites, which characterize about 10,000 feet of the Middle Aldridge in the Purcell range, have a restricted development amounting to only 2,000 feet in the Rocky Mountains. This member is about 2,200 feet above the mine horizon."

Jan 1, 1949

By Edward A. Loria

Vanadium is one of the materials being considered for use in fast-breeder nuclear reactors. It is a good heat conductor and nearly transparent to radiation, properties regarded as ideal for nuclear fuel containers. The problem has been the metal lacks ductility needed for forming. In our program at Reno Laboratory the effects of the U.S. Bureau of Mines (previous affiliation) the effects of oxygen, nitrogen, and carbon have been reported21,22 nd most recently the effects of boron and boron with carbon.23 The continuing study by the Ames Laboratory of the effects of hydrogen, the most subtle and fugitive element in its relationship to structure and properties, is commendable. The solubility of oxygen, nitrogen, and hydrogen in vanadium (and other bcc metals as well) is related to material purity. With the available limit on metal purity and the interaction (clustering) of hydrogen with the other interstitial and substitutional elements present in their base metal, would the authors comment on the tolerance of hydrogen in relation to oxy- gen that will avoid intergranular fracture and above what content or how seriously harmful in oxygen at various carbon levels? Understanding the true effects of hydrogen (and other interstitial impurities) in vanadium depends on knowledge of the amount present under various conditions and its distribution between various possible positions. Significant amounts of hydrogen may be in "thermo-dynamic" solution, but not as individual atoms in interstitial positions. It may be in grain boundaries, in subgrain boundaries, in vacancies, or in dislocations. Some of the hydrogen may be paired or in complexes with impurities in substitutional solid solution in vanadium. This makes the analysis of the effect of hydrogen vastly more difficult. It should not be expected that hydrogen in grain boundaries will affect slip in the same manner as hydrogen in interstitial positions, nor will the complexes react to heat treatment the same way as hydrogen in dislocations. It is gratifying that the authors have quoted results from two of our inestiations,' but neglected one2' which applied the Petch theory to electrorefined vanadium of high purity and analyzed the effects of oxygen, nitrogen, and carbon on the ai and ky values obtained by the extrapolation and grain size methods. Details can be found in the paper. Briefly, we obtained a ui value of 10,300 psi (t = 5150 psi) at 273°K. The metal also exhibited profuse twinning with high ductility at 123" and 77°K. Nitrogen was more effective than oxygen in increasing ui, the increase being about twice as much for the same impurity level. Carbon additions resulted in only minimal changes in Ui. The corresponding ky increased as oxygen and nitrogen increased, with nitrogen being more effective. Carbon additions resulted in little change. Although the difference in yield strength of vanadium was explained on the basis of the Cottrell-Bilby model of the tearing away of dislocations from the impurity atoms,

Jan 1, 1970

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselman Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo. 12. Chaco River area, N. M. 13. Lewis and Thurston County fields, Wash. For two of these areas; the Paonia field, Colo., and the Coosa field, Ala., we have published recently preliminary reports, and final reports are in preparation. In addition, we are nearing completion of a coal reserve study of Montana, and are beginning similar studies in several other states, as part of a program of revising our estimate of national coal resources on the basis of presently available data. Factors Involved in Making Estimates Our responsibilities include detailed field mapping to secure information on areas of outcrop of coal beds, their range in thickness, nature of roof rock, amount of overburden, correlation of the beds, stratigraphy and structure of the coal-bearing rocks, and the preparation of coal reserve figures based on these data. The computation and estimation of resources of coal in the ground, like that of resources of other mineral commodities, involves consideration of many additional purely geological factors that can be appraised best through such regional studies. Regional variations in the thickness and texture of rocks overlying and underlying coal beds, for example, give evidence as to the probable position of the edges of the basin of coal deposition, or may aid in the delineation of sand-filled channels that sometimes cut out coal beds. It is apparent that the detailed field studies, in which data are gathered, are the basis for coal reserve studies, and in our present program these two phases of work are being carried on together. Previous Coal Reserve Estimates For many years we have been aware

Jan 1, 1950

By Clarence W. Balke

SMALL buttons of fused tantalum have been produced by arc fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By P. F. Gnirk, J. B. Cheatham

The results of combined analytical and experimental studies involving simulated multiple bit-tooth penetration into mck are incorporated into a drilling rate equation for roller-cone bits assuming rather idealized downhole conditions. In particular, it is assumed that the rock behaves statically in a ductile fashion during bit-tooth penetration and that the rock chips are instantaneously removed from the bottom of the drill hole. The general analysis demonstrates an application of plasticity theory for the rock/bit-tooth interaction to the formulation of an upper limit on rotary drilling rate. INTRODUCTION Extensive experimentation involving single and indexed bit-tooth penetration into rock in a confining pressure environment has demonstrated that the chip formation process is of a ductile, or pseudoplastic, nature at sufficiently low differential pressures so as to be of interest in rotary drilling. Coincident with the experimentation, analytical consideration has been given to the theoretical problems of single and indexed bit-tooth penetration into rock. In general, the analyses have assumed that the rock behaves statically in a rigid-plastic fashion and obeys the Mohr-Coulomb yield criterion. The quantitative comparison between experimental and calculated values of bit-tooth load required for chip formation has been remarkably good for a variety of rocks commonly encountered in drilling and at simulated differential pressures as low as 500 to 1,000 psi. Results obtained recently for indexed bit-tooth penetration indicate that the work (or energy) required to produce a unit volume of rock chip can be minimized by a proper combination of bit-tooth spacing and bit-tooth load for a given rock type and differential pressure. By utilizing this information, it is possible to formulate a drilling rate equation, at least in a preliminary fashion, for a roller-cone bit performing under rather idealized downhole conditions. In particular, through the use of characteristic dimensionless quantities pertinent to a roller-cone bit and to indexed bit-tooth penetration, interrelationships among bit weight, rotary speed, rotary power, bit diameter, rock strength and bit-tooth shape and spacing can be explicitly expressed. In the formulation of the equations, however, it is assumed that the rock chips are instantaneously removed from the bottom of the drill hole and- that the rock behaves in a ductile manner during bit-tooth penetration. In addition, the effects of bit-tooth load application and penetration by a yawed tooth at an oblique angle are neglected. Although the analysis is presented in the light of some rather restrictive conditions, it does demonstrate a method of applying fundamental rock/bit-tooth interaction data, obtained by combining the results of analysis and experiment to the formulation of a drilling rate equation for rotary drilling. JNDEXED BIT-TOOTH/ROCK INTERACTION PREVIOUS RESULTS The mechanics of bit-tooth/rock interaction under simulated conditions of borehole environment have been extensively described in a number of papers.l-ll In particular, the effects of differential pressure, mechanical properties of rock, pore fluid, bit-tooth shape and spacing, rate of bit-tooth load application and dynamic filtration below the bit-tooth have been investigated experimentally. From a sequence of experiments.1-4 it was demonstrated that, for dry rock at atmospheric pore pressure, the mode of chip formation exhibits a transition, with increasing confining pressure, from predominantly brittle to predominantly ductile. This transition

Jan 1, 1970

By James D. Noll, Jon A. Hummer, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health conducted a study to determine the effects of selected, state-of-the-art emission control technologies on the ambient concentrations of particulate matter and gases emitted by underground diesel-powered mining equipment. Tests were conducted in an isolated zone of an underground mine to evaluate the effectiveness of alternative fuel formulations, namely, water-fuel emulsions, blended biodiesel fuels, ultralow sulfur diesel fuel, and #1 diesel; and selected exhaust after treatment devices, namely, diesel oxidation catalysts (DOCs), diesel particulate filter (DPF) systems, and filtration systems designed around high-temperature disposable filter elements. The results showed that using a cold-weather and warm-weather water-fuel emulsion formulation reduced mass concentrations of elemental carbon (EC) by about 70% and 85%, respectively. The 20% and 50% soy biodiesel blends reduced EC by 49% and 66%, respectively. The reductions were slightly less pronounced for the 20% and 50% yellow grease biodiesel blends—33% and 56%, respectively. EC concentrations were unaffected by using ultralow sulfur diesel in place of #1 diesel. Use of the reformulated fuels did not substantially alter the concentrations of nitric oxide and carbon monoxide. However, a measurable increase in the nitrogen dioxide (NO2) peak concentration was observed during the biodiesel tests. The ArvinMeritor (AM) fuel-burner DPF system with a palladium-catalyzed DOC reduced EC concentrations by 92%. The diesel filter elements from Donaldson Co., Inc., and Filter Service & Testing Corp. reduced the EC concentration of the mine air by 92% and 70%, respectively. When the palladium-based DOC was used with the AM DPF, it raised the average and peak downstream NO2 concentrations by a factor of three. Tests of the AM DPF system with a platinum-catalyzed DOC and CAP/ETG catalytic particulate oxidizer system had to be terminated because the elevated NO2 concentrations threatened to overexpose the operator. The tests with only a selected DOC also resulted in increased NO2 concentrations in mine air.

Jan 8, 2006

By A. L. Titchener, M. B. Bever

The stored energy of cold work was investigated in drawn gold-silver wires by tin-solution calorimetry as a function of strain, strain rate, initial grain size, and temperature of defornation. The energy expended in the deformation process was measured. Hardness was also measured and was correlated with the stored energy as a function of strain and strain rate. Mechanisms of energy storage are discussed. THE variables which determine the amount of energy stored in a metal during cold work are of two kinds: those involving the metal and its condition and those involving the process of deformation. For example, the stored energy differs between one metal and another and between different degrees of purity of a single metal. It also depends on the nature of the deformation process and particularly the extent, rate, and temperature of deformation. Most investigators have reported the stored energy as a function of strain (or some similar geometric parameter) or of the energy expended during deformation. In general the stored energy increases with strain, rapidly at first, but more slowly at large strains until a saturation level is reached. Information about the effects of other variables, however, is limited. Some data are available on the dependence of the stored energy on the purity of a metal1 and on the composition of

Jan 1, 1960

By G. M. Ritcey, A. W. Ashbrook

"This paper summarizes the optimum leach conditions for each Of several cobalt-containing arsenical feed materials, describes the solution treatment prior to purification of cobalt recovery, and discusses the plant operation on one feed as well as the treatment of effluents.IntroductionDuring the period 1962-1964, when the demand for uranium was low, Eldorado Mining and Refining Limited (Eldorado Nuclear Limited) made a decision to undertake a three-year diversification program. One area chosen in this program was that concerned with the processing of cobalt-nickel materials. Many such materials were evaluated over the three-year period, ranging from tailings, residues, ores, concentrates and speiss to metal scrap. Cobalt feed materials, on which much of the effort was concentrated, were those containing arsenic together with other metals such as silver, copper, nickel and iron. This paper describes the treatment of arsenic-bearing feed materials (ranging from 0.3 to 570/0 As) and the subsequent purification stages required before the separation and recovery of high-purity cobalt. Because of the current interest in treating cobalt ores, it seemed appropriate that the information on the treatment of various cobalt feeds should now be made available . Although a large amount of data were generated during the research and process development program, a complete scientific correlation and understanding could not be achieved. Nevertheless, the data may provide a guide to others involved in processing not only cobalt, but other arsenical ores."

Jan 1, 1981

By Kenta Kusunose, Dadang Sundana, Ahmad Munib Fikry, Yosuke Unno

PT Smelting has operated the Mitsubishi Process in which feed materials are charged into the S- furnace through top lances using a pneumatic conveying system comprising 6 feeding tanks (S-Feeding Tanks). Each S-Feeding Tank was designed as a batch machine and had been operated in a batch mode so that feed materials are conveyed 70% of the operating time (conveying time). An S-Feeding Tank was revamped in August 2016 in order to attempt to achieve 100% conveying time during operation, aiming to reduce the furnace draft fluctuations and melt temperature fluctuations leading to reduced copper losses to slag and refractory wear on the sidewall in the melt zone. After two-year operation with some adjustments and modifications, it was concluded that the new system works as expected. During scheduled major shutdown in November 2018, the same modification was applied to all other 5 feeding tanks as the first one, while several modifications other than the S-Feeding system were also conducted for the purpose of expanding the capacity of the smelter. INTRODUCTION PT. Smelting (PTS) Gresik Copper Smelter and Refinery is located 30 kilometers north of the city of Surabaya, East Java major port. PT Smelting equity partners are Mitsubishi Materials with 60.5%, PT. Freeport Indonesia with 25%, Mitsubishi Corporation RtM Japan Ltd. with 9.5% and JX Nippon Mining and Metals corporation with 5.0%. PTS was established in February 1996 and started commercial operation of the Mitsubishi Process in 1999. The Mitsubishi Process is a unique technology which connects 3 stationary furnaces, namely the Smelting furnace (S-furnace), Slag-Cleaning furnace (CL-furnace) and Converting furnace (C-furnace) by covered launders. These features result in savings in manpower and energy, and make the process more environmentally friendly since there is no ladle transfer of melt. Figure 1 illustrates the outline of the Mitsubishi Process.

Jan 1, 2019

By Pat Gochnour, Jim V. Rouse

Advances in the design and construction of heap­leach pads and process plants have greatly reduced. the potential for accidental releases of process olut1on. While workers in the field, and regulatory agencies such as the EPA have long recognized that the potential effects of any spills would be short term in nature due to cyanide attenuation and degradation (Engineering-Science, September, 1986, Pyrih, 1990, Rouse and Pyrih, 198, Rouse and Pyrih, 1991 ), unfortunately the general pubhc has held a perception that such a spill would be an environmental catastrophe. Few factual data on actual accidental releases have been available to dispel such a concept. Such data now exist and shoul? be disseminated to show that prompt response, using a combination of chemical oxidation, natural attenuation, and enhanced biodegradation of cyanide, can limit the effects of such rare releases, in both time and space.

Jan 1, 1992

By John Petty, John Loviza

As a blaster, have you ever had that uneasy feeing in the pit of your stomach as a codes enforcement official drives onto your jobsite? Have you ever needed an ally in a court of law against an unjust damage claim? Have you ever wished for a better and more open relationship with the guys who wear the badges?

Jan 1, 1996

By W. Kennedy Gauger, Tim Oolman, Debra L. Bisson

Radian Corporation (Radian) has developed a process for treating Cr(V1)-contaminated soils that involves: 1) soil washing using an alkaline extractant, 2) biological reduction of Cr(V1) to Cr(II1) in the soil wash effluent, and 3) separation of Cr(II1) from the biologically treated effluent. Biological treatment has been demonstrated for immobilized cells in fluidized bed bioreactors and suspended cells in slurry bioreactors for Cr(V1) levels ranging from 30 to 600 mg/L which have been reduced to non-detectable levels (< 0.05 mg/L; method detection limit [MDL]) during hydraulic residence times as short as 12 hours. The resulting Cr(II1)-containing effluent stream was chemically treated to precipitate chromium hydroxide for removal by physical separation.

Jan 1, 1995

The InLine Pressure Jig represents a breakthrough in digging technology Its design incorporates a unique combination of features previously utilised in conventional jig design. In particular, a moveable screen and circular bed are used to excellent effect. However, a major design innovation is the encapsulation of the circular bed within a vessel - allowing the equipment to operate under pressure. This innovation eliminates free water surface, improves the dynamics within the separation layer (crossflow) and provides significant cost savings in the handling of slurries. Recent research results have indicated its capacity to achieve high recoveries and upgrade ratios in the gravity separation of Minerals.

Jan 1, 1997

By Rafael Bartra

"El presente texto señala los aspectos geológicos en la mina Yanacocha. La Minera Yanacocha es un Joint Venture, que incluye a Newmont Mining Company (51%), la Compañía de Minas Buenaventura S.A. (44%), yla International Finance Corporation (5%). Dicho distrito tiene una larga historia en prospección y actividad minera, que data desde tiempos pre-Incas hasta nuestros días y es un sistema sulfato dentro de un complejo volcánico de edad terciaria. Asimismo el distrito ha sufrido glaciación postmineral y el yacimiento de La Quinua recientemente descubierto, se encuentra en gravas auríferas derivadas de la glaciación del yacimiento de Yanacocha Sur. De forma que Yanacocha es uno de los principales distritos ácido-sulfato del mundo en términos de contenido de onzas de oro, producción anual y costo de producción. "

Apr 26, 1999

By A. Montini

The problems encountered in the design of control systems for milling cir- cuits when the model of the system and the model parameters are uncertain are discussed. Considering these uncertainty factors has led to the development of a technique that gives a quantitative assessment of real system stability, reveals the trade-offs between performance and stability and helps the designer in deciding what level of model complexity to use in the controller design. Furthermore, it allows for on- or off-line optimization of the milling circuit performance as it provides the base for the design of a controller which is stable over the plant operating range.

Jan 1, 1987

By Laxman M. Amaratunga, David N. Yaschyshyn

"In the mining industry several types of fills are used for backfill operations. They are broadly categorized into three basic types: rock fill, hydraulic/slurry fill, and paste fill. Recently, paste fill has become the popular alternative for backfilling because of its many environmental and operational advantages including its ability to use total tailings, both fine and coarse fractions.Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings, which are otherwise excluded from backfilling, for utilization in backfill as a readily available supplementary fill material. Previous experimental work investigated the use of agglomerated fine gold mill tailings in low density slurry fills (60 -70% pulp density), consisting of varying agglomerate and tailings compositions.This paper presents the ongoing research into utilizing these agglomerates in a high density paste fill (70 -85% pulp density). Various binder dosages, curing period and combinations of pellet to tailings ratios were studied. Slump of the raw fill and compressive strength of the cured fill were examined. Results from the above study indicate that agglomerated tailings paste fill (ATPF) has superior strength characteristics when compared to total tailings paste fills.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. These tailings consist of a coarse fraction and a fine fraction and can be either reactive (acid generating) or non-reactive. Most mining operations utilize the coarse fraction for backfilling while the fines have been traditionally disposed of in surface tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10 - 30% w/w of >45 µ,m) in the fill. This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused portion of fine tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMD) seepage from these ponds has proven to be a costly environmental problem and long term liabilty.One practical method to reduce the environmental impacts associated with the tailings pond and to modify the physical and chemical properties of the fine mill tailings so that they can be utilized and disposed of in an environmentally safe manner through surface or underground applications is through agglomeration using the Cold-Bond Tailings Agglomeration technology (CBTA). Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings for use as coarse aggregates for underground backfill, gravel or surface covering material. CBT A reduces the necessity of impounding tailings on surface while providing a suitable coarse aggregate resource material for practical use. Although the CBT A technology has been mainly limited to pelletization agglomeration alone, other forms of agglomeration like pressure agglomeration which include the techniques of briquetting and extrusion have also proven successful (Amaratunga, 1995)."

Jan 1, 1996

By Fred H. Lightner

Mergers and acquisitions (M&A) within the mining industry are becoming frequent events. Large companies and small companies alike are jumping on the bandwagon of merger mania. The results of these mergers have significant impacts on the employees of the involved companies. Comments, observations, and specific examples of the &apos;peop1e"aspect of mergers are presented in an attempt to answer the question "will it be business as usual?" My answer is a simple NO. This paper attempts to provide support for my conclusion. The reader should recognize that the comments, observations, and specific examples mentioned in this paper are subjective and reflect the experience and prejudice of the author.

Jan 1, 2001

By W. J. Loring

It is proposed to describe in this paper as accurately as possible the present practice at the Utica mills, of which I am superintendent. The Utica Company operates three mills, the Madison (40 stamps), the Utica (60 stamps), and the Stickle (60 stamps). My description will be based on the last-named, in which I have experimented more than in either of the other two; but the practice is the same, under the same management, in all three. Everything is run by water-power, under about 420 feet fall at the Utica mill, and 425 feet at the Stickle mill, giving a pressure of about 185 pounds to the square inch. The Madison mill is situated about three-quarters of a mile below the Utica and Stickle mills, and has only some 100 feet fall from one place, and 38 feet fall from the other. The water that runs the Utica and Stickle mills, and all machinery connected with the corresponding mines, is conveyed through ditch and pipe to the Madison mine and mill, where it develops power for the air-compressor and the 40-stamp mill. The mill is run by a

Jan 1, 1899

By D. W. Rudd, D. W. Vose, J. B. Vetrano

In an earlier paper the permeability character of Mo-0.5 pct Ti to hydrogen was described.&apos; It was shown that this alloy is a more effective barrier to the passage of hydrogen than previously studied systems, i.e., copper,2 nickel,3 and several stainless steels.4 The permeability of Hastelloy B to hydrogen was investigated as a material having promising high-temperature structural properties which might have a low permeability to hydrogen. The general theory of permeation has been previously discussed,&apos; and here only a summary of the more important results are given. It is found that except for very thin membranes, at low temperature, permeation of a gas through a metal barrier is determined by the rate of diffusion of the gas through the crystal lattice of the specimen, and that for hydrogen and the common diatomic gases, this passage involves dissociated particles as the diffusing species. The rate of permeation for hydrogen is therefore proportional to the square root of the pressure. It has also been found that the rate of permeation is inversely proportional to the thickness of the barrier. The apparatus used in this investigation was fundamentally the same as that employed in previous studies,&apos; except that several simplifications result in the case of Hastelloy, since oxidation at the temperatures investigated is no longer a problem and welding of the specimen is relatively easy. A cross section of the membrane assembly is shown in Fig. 1. When finished, the assembly is about 5 in. long. The wall thickness is about 6 times the membrane thickness. The membrane (A) can be maintained at

Jan 1, 1963

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001