Search Documents

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By C. W. Schultz, R. B. Tippin

Statistical screening is so named because a particulate feed is separated into "size" intervals on the basis of the probabalistic behavior of the individual particles (i.e., their probability of passing the screen) rather than by physical restraint. To illustrate this statement, consider a conventional screening operation. A particle which is larger than the openings in the screen cloth is physically restrained from passing through and is repeatedly reflected from the surface until it is discharged as oversize. Of those particles smaller than the screen openings, the very smallest tend to pass the screen near the feed end while those nearer in size to the screen opening tend to pass at a greater distance from the feed end. Alternatively, we could say that the particles with high probability of passing through the screen are concentrated near the feed end while particles of low probability of passing are dispersed from the feed end. This tendency to segregate is the basis for size separation by statistical screening. The purpose of this note is to: 1) Show that the distribution of material passing an array of screens can be described by a modified binomial distribution. 2) Demonstrate that an efficient size separation can be made by this technique. 3) Relate some of the more important screening parameters to the efficiency of the size separation. The Distribution Function The distribution of undersize products along the length of a screen can be derived with the help of a few simple definitions and assumptions. 1) First, we must assume that each particle has some probability of passing a screen on a single presentation. Further, we must assume that this probability is constant and is not affected by the position of the particle on the screen. It must also be acknowledged that several factors enter into this probability. Among them are the "action" of the screen, the slope of the deck, the shape of the openings, etc. The relationship between these factors, however. is not the subject of this paper. 2) To simplify calculations, all particles falling within a size range on the Tyler scale, e.g., —x + x/ mm, are assumed to have the same probability. 3) It is assumed that particles which do not pass the screen on a presentation are reflected a unit distance forward, i.e., the direction of material travel. A unit distance is defined as the distance between the centers of consecutive wires in the screen cloth.

Jan 1, 1971

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011

By D. Tahija

The Getchell Mine produces gold from a geologically complex ore bearing high concentrations of arsenic and carbonate minerals. The mill treats the ore using high temperature aqueous oxidation in autoclaves, followed by conventional carbon-in-leach gold recovery. We laboratory tested a variety of Getchell ores to determine the effects on gold recovery of conventional factors such as grind size and retention time, as well as the influence of factors such as ore variability and preliminary carbonate destruction. Because the mill is currently operating, we were able to directly compare certain laboratory predictions with operational results.

Jan 1, 1999

By George Collins

AT the meeting of the Western Division of the American Mining Congress, held in Denver last September, papers were read by F. H. Brownell, a vice-president of the American Smelting and Refining Co. and chairman of its finance committee, and by H. Foster Bain, former director of the United States Bureau of Mines and now secretary of the A. I. M. E.. which dealt thoroughly with certain phases of my sub-ject. These addresses can hardly have failed to awaken serious reflection in all who listened to them; but their implications have apparently not penetrated the con-sciousness of bankers, economists and statesmen, whose business it is, or should be, to prepare for the economic and social changes which must inevitably follow, if the conclusions which I shall outline hereinafter are true. In discussing this subject I wish to disclaim any intention or desire to forecast the course of the metal markets or the immediate prospects of the mining in-dustry. The facts' adduced must inevitably influence the value of metals, the activity and profitableness of mining, and perhaps also the social status of those en-gaged in it. But my forecasts do not refer to this year, next, year, or the year after. The nearest ap-proach to a date on which I will venture is that the relative scarcity of gold may begin to make itself felt in something like ten years from now, but its effect will not culminate for several years thereafter. Scarcity of new gold is likely to be offset, to some extent, by increasing use of currencies based on credit; but unless it is found possible to dispense with the gold standard altogether, this can hardly prevent a great ultimate fall in commodity prices. This fall, moreover, is likely to be more severe in manufactured goods than in what are, popularly termed raw ma-terials; and most of all in those manufactured goods which are susceptible to the greatest degree to cheapen-ing by mass production, and which are least counter-affected by increasing metal prices; by which I mean those in which the cost of metal contained forms a relatively small, element in the total cost of production.

Jan 6, 1927

By E. J. Gleim

In the movement of self-controlled direct-current machinery, particularly shortwall cutting, machines, from one place to another in coal mires, "nipping" or it stinging" has been practiced quite commonly. These terms refer to the method of obtaining current for propelling or tramming the machines along trolley haulageways by sliding the trolley trip (hook or nip), which terminates one conductor of the trailing cable, along the trolley wire. This is usually done by the machine operator or runner while sitting on the machine truck and holding the nip terminal against the trolley wire as the machine travels along the rails. This procedure is objectionable for several reasons. Under the best conditions, the area of contact between the nip and trolley wire is snail end, consequently, sparking and flashing ore most likely to be continuous as the machine proceeds. This is undesirable, not only because of the detrimental effect of electric flashes upon eyesight, but because of the pitting and roughening the trolley wheels which decrease the efficiency of current collection by locomotive trolley wheels and shoes and at the same time shorten their useful life by increased wear.

Jan 1, 1939

By Lynn M. Gould

Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13 percent of Canada?s total oil requirements. To do this, Syncrude mines the oil sand in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB) is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States. As parts of the Mildred Lake Base Mine reached their economic life, they were replaced with new facilities at the Aurora satellite mine. Aurora is situated on Oilsand Leases 10, 12, and 34, 35 kilometres northeast of the Mildred Lake facility. (Figure 1) In 2000 the first hydrotransport low energy extraction production train started up at Aurora. A second production train is scheduled for start up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320 ton to 380 ton payload capacities.

May 1, 2002

Beneficiation and dephosphorization of refractory oolitic hematite ore are investigated in this paper. It is shown that single magnetic separation, gravity separation or flotation is unable to recover iron effectively from the ore due to the complex mineralogy. The joint separation by spiral chute-shaking table shows a prospect for the treatment of the ore. An iron concentrate with 58.67% iron grade and 51.93% recovery is obtained by the joint separation of spiral chute and shaking table under the fineness of ?0.074mm 90% and dispersant dosage of 2kg/t for a sample ore of 37.51% Fe and 0.88% P. However, P content in the concentrate is still up to 0.52%. Dephosphorization from the concentrate is hence carried out. The final iron concentrate assaying 59.26% Fe and 0.056% P is obtained when the concentrate obtained by joint separation is leached by sulfuric acid of 1% (mass fraction) with solid percentage 10% at room temperature for 10min.

Jan 1, 2014

By Leo J. Miller

It is both an honor and a pleasure for me to be the keynote speaker for the Paul F. Kerr's Symposium on Applied Mineralogy. Professor Kerr was a man for all seasons to his students, and he treated all students as distinct individuals. Philip Bethke in his memorial to Dr. Kerr summed up our remembrance best by stating that "We have lost our most successful educator-administrator-scholar, who was our steadfast teacher-counselor-mentor-friend." His unique trait was the ability to bring out the best in a variety of individuals In order that their performance was at the peak of quality.

Jan 1, 1985

By John Reilly

Traditional methods of project procurement of have remained virtually unchanged in the U.S. infrastructure construction industry for more than 50 years. The traditional method, Design-Bid-Build (DBB), uses a two-step process that separates planning and design from construction. Design is generally done by the public agency and their consultants and the subsequent construction contract is procured from the private sector, almost always by a “low-bid” approach. This method has worked well for many projects, delivering quality work for the lowest bid price. This is particularly true for those projects where the work, and the public agency’s management procedures, are well understood by the contracting community and there is relatively low uncertainty in the work or conditions, particularly geotechnical conditions for underground construction. However, concerns exist with the DBB process. It is time consuming because all planning and design work must be completed prior to beginning any construction work and it is of concern for complex or large projects, plus those with significant risk, where the separation of design and construction, in conjunction with pressures resulting from the low-bid environment, often result in substantial cost and schedule increases. Frequently, these increases occur in a non-productive, inefficient, adversarial work environment leading to claims, disputes and costly litigation (Quick 2002).

Jan 1, 2007

The placer gold industry has experienced a roller-coaster history incorporating four major boom eras. The first, 'hand-methods' boom arose in the mid-19th Century from application of an old idea in new places around the globe. The subsequent hydraulic mining, bucket dredging, and 'hydraulic excavator-portable plant' booms each arose from application of new ideas in old places around the globe, ie in places where gold had been found during earlier booms. The new ideas that heralded the second, third and fourth booms were all significant advances in excavation technology. These enabled the industry to target the known deposits that were too deep, too wet, too small, or too low-grade for recovery by earlier boom methods. Relatively few new deposits or new deposit styles arose from the 'history book' exploration approach, so the number of known deposits to which each of the boom methods were applicable was limited. Consequently, the first three booms were each followed by significant periods of industry decline, and the fourth boom is currently waning inNew Zealand. Further decline is not inevitable and can be avoided by changing to a knowledge-based exploration approach similar to that adopted by the hard rock gold industry in the 1970s. Such an approach could easily herald the next placer gold boom.   Most of the relatively coarse, easily won alluvial gold in proximal and medial reaches of the active placer systems is gone. However, a substantial alluvial gold resource remains in the distal reaches of active systems, and in ancient placers formed onshore and on the continental shelf during previous sedimentary cycles. The resource in these deposits probably exceeds the total New Zealand placer production to date. Successful development of these placers requires application of robust geologic models for the formation and distribution of the placers through time, and advanced exploration technology that has not been used before in New Zealand. Nevertheless, the knowledge and technology required to explore and mine these deposits is available now. Many of these deposits contain a large proportion of problematic gold types that are difficult to recover with the commonly used gravity technology without sustaining significant losses. Despite advances in recovery technology in last few years, too much emphasis is placed on the incorrect assumption that gold size is the primary control on recovery efficiency. Other gold particle parameters, especially particle shape, exert a much greater control on whether gold will be saved or lost to the tails, and must be considered in the design of recovery technology and configuration of recovery circuits.

Jan 1, 2003

By F. Woodcock, A. R. Laplante

A test to characterize the amount of gravity-recoverable gold (GRG) in an ore is described. Typical GRG results are given and possible uses are discussed. The overall database, which includes 68complete tests, is presented. The ore samples treated had an average GRG content of 63% of the total gold in the sample, with a standard deviation of 20% and a range of 3% to 97%. Both the F8(, of gold and the GRG content at a grind of 100% finer than 850 pm correlate well with the overall GRG content (at 80%finer than 75 pm). The primary use of the test is to determine whether gravity recovery should be used and how. Results can also be used to predict gravity recovery, as many of the ores tested are from plants employing gravity recovery. Gravity-circuit simulation can be used to refine recovery estimates or for optimization studies.

Jan 1, 2000

By D. L. Stewart

"Melt loss is usually one of the highest individual cost items in the operation of ah ingot casting facility. While melt loss and the resulting cost for the entire facility is usually well known (at least via standard cost accounting), dross generation and melt loss for individual unit operations within the plant are usually not known. Thus, the financial impact of various practices, alloys and scrap types is not known. Development of an accurate, relatively low-cost technique for measurement of melt loss at commercial scale would aid in understanding melt loss for existing units, as well as evaluation of the melt loss impact of alternate processes.This paper will describe a methodology developed at Alcoa for accurate and inexpensive measurement of melt loss at commercial scale. The methodology has been used to evaluate the impact of scrap type, melting practices, and dross treatment technology on melt loss."

Jan 1, 2000

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By Ben-Zion Weiss, Melvin R. Meyerson

FATIGUE crack propagation in some aspects can be viewed as being a result of localized plastic deformation concentrated near the tip of the crack.' Deformation is influenced by microstructure which in turn can affect the fatigue crack growth significantly. To study the effect of localized microstructural changes on fatigue crack propagation, cantilever-type notched specimens were subjected to cyclic bending at constant load amplitude. The extent of fatigue crack propagation was obtained by measuring the length of the crack by periodic observation with a microscope on the polished side of the sample,2"4 and these data were used in preparing the curves in the figures which follow. Figs. 1 (solid lines) and 2 show experimental results obtained in austenitic type 302 stainless steel containing higher than standard carbon (0.24 pct C) and 310 stainless steel. Both steels were homogenized for 8 hr at 1120°C and then water-quenched in order to prevent the precipitation of carbides. Fig. 3 shows experimental results obtained on 9440 low alloy steel in the normalized condition and in the quenched and tempered (580°C) condition. Indications of microstructural influence can be seen in scattering of the experimental data. The degree of scattering depends on both the microstructure and the amount of cyclic stress applied to the sample. For microstructures which are more easily deformed plastically, e.g., normalized or annealed as compared with hardened and tempered structures, the scattering is greater. Similarly, higher stresses produce greater scattering in the results, regardless of whether the cause of the stress increase is due to initial loading conditions or the growth in crack length. Scattering is believed to be a result of partial redistribution in the stress field around the tip caused by plastic deformation. This opinion is borne out by much smaller scattering of experimental results in the austenitic 302 high-carbon (0.24 pct C) steel. In this steel, plastic deformation in the neighborhood of the crack causes partial mar-tensitic transformation of metastable austenite,5 which in turn restrains further plastic deformation. As a result, the stress redistribution around The tip is reduced. Partial martensitic transformation was confirmed

Jan 1, 1969

By N. S. Dalal, B. Jafari, F. Y. H. Green, V. Vallyathan

"Using electron spin resonance (ESR) spectroscopy we have carried out a systematic study of the measurement of concentrations of organic free radicals in freeze-dried lung tissue. Sixty-six tissue samples were obtained from the National Coal Workers' Autopsy Study (NCWAS). The samples were characterized in terms of the concentration per gram of the free radicals, and examined in relationship to the histopathological parameters such as age, numbers of years in the mining atmosphere, the degree of disease, and smoking history. Preliminary results indicate a positive correlation between the free radicals in the lung tissue and the severity of pneumoconiosis.IntroductionThis paper summarizes our electron spin resonance (ESR) measurements of the concentration of organic free radicals in the freeze-dried lung tissue of autopsied coal miners. This work was undertaken because it is well known that most coals contain carbon-centered organic free radi¬cals,(1,2) and recent studies from our laboratories indicated that reactive free radicals might play a role in the biochemi¬cal mechanism of coal workers' pneumoconiosis (CWP) (3) Thus we obtained 144 lung-tissue samples from the Nation¬al Institute for Occupational Safety and Health (NIOSH) in Morgantown. The samples came from the data bank of the National Coal Workers' Autopsy Study (NCWAS). This selection was unique because fairly detailed histopathologi¬cal information was available for each sample.Other recent studies in this field are those of Ohta et al (4) who conducted ESR measurements on black dust deposited in autopsied human lungs, but no coal miner was included therein. Earlier Retcofsky (2) had examined one lung-tissue sample via ESR spectroscopy and had concluded that the free radicals in the lung tissue reflected simply the fusain (narrow component) ESR signals. The present study was thus undertaken to complement the earlier work (2-4) and the results indicate a positive correlation with the disease severity fairly strongly."

Mar 1, 1989

By E. N. Cameron

GRAPHITE has been included in U. S. lists of strategic minerals since the problem of mineral deficiencies was revealed during World War I. Since 1918 the domestic graphite industry has led a precarious existence, and there has been much uncertainty as to the amounts of usable graphite of various grades that would be available from domestic sources in time of emergency. In 1950-1951 therefore, the writer, assisted by Paul L. Weis, undertook a review of domestic graphite sources for the U. S. Geological Survey.' The conclusions of this study are presented here, with a discussion of some technologic and politico-economic factors bearing upon the problem. Uses of Graphite: Natural graphite as marketed exhibits a wide range of properties, which determine the uses to which it is put. The most essential uses are in the manufacture of crucibles and related refractory articles, in lubricants and packing materials, and in the manufacture of batteries, foundry facings, pencils, and carbon brushes. Numerous specifications covering the mineral in its various applications must be met by producers and processors of graphite. The problem of supply is therefore not simply one of procuring a sufficient total tonnage, but the more difficult problem of procuring enough of each different grade to meet foreseeable needs. The amount of graphite required by American industry is not large. Ordinarily only a few thousand tons of strategic grades are consumed annually, yet the elimination of this small tonnage would have serious effects in several industries. Strategic Graphite: Since World War I, 60 to 100 pct of the country's annual supply of graphite has been furnished from imports. At present, natural amorphous graphite for use in pencils and batteries is produced largely from American-owned mines in Mexico. Graphite for foundry facings is obtained from a number of sources. Neither grade is a serious problem. High purity graphite for carbon brushes and for pencil leads, however, is imported, largely from Ceylon, in the form of amorphous lump graphite. Most of the flake graphite used for crucibles and related refractory articles is likewise imported, largely from Madagascar, and much of the lubricant and packing grade graphite used by industry is obtained from the same source. The strateg'ic grades of graphite are therefore amorphous lump of the Ceylon type, crucible flake, and flake suitable for lubricants and packing. Ceylon lump and Madagascar flake have for many years been accepted as standard by domestic consumers of graphite, and various essential manufacturing processes are geared to the use of graphite from these sources. Ceylon graphite as marketed is classified into several grades based on particle size and purity. Processing methods are said to be simple, but the products marketed are carefully graded and are consistent in their characteristics, an important matter to the consumer. Nearly all the graphite produced in Ceylon is from veins. Resources are reported to be large, labor is cheap, production costs are low, and world competition is slight—factors accounting for the commercial success of the graphite mining industry in Ceylon. Madagascar is reported to have deposits of the Ceylon type, but its output consists almost entirely of flake. Madagascar graphite as received in the U. S. is further processed by importing organizations, and a large number of grades are produced to meet industry requirements, especially those for crucible flake and for lubricant and packing grade flake. Madagascar crucible flake as marketed is noted for coarseness, uniformity, toughness, clean-

Jan 1, 1957

By M. Azzaz

In this paper, we report on new mechanical tests, at high temperatures, performed with a supposed better aluminium nitride (A1N) material, containing fewer oxygen. Our purpose was twofold: (i) check whether creep resistance is modified and hopefully enhanced and (ii) determine the elementary mechanisms controlling plastic deformation through transmission electron microscopy (TEM) observations of deformed samples up 10% strain in compression at elevated temperatures (1823-1923 K) under constant stress in the range 150¬250 MPa. Stationary rates are lower by an order magnitude than those previously measured in MN with higher oxygen content. All dislocations imaged by TEM look undissociated, which clearly relates the formerly observed wide dissociation to oxygen in excess.

Jan 1, 2004

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By T. J. Woodside

Prior to 1927 the lead blast furnace charge at El Paso consisted principally of direct-smelting carbonate ores, very low in zinc, and the resulting slag seldom carried more than 4.0 pct. With the exhaustion of the mines in Northern Mexico which supplied these ores, they were supplanted with a much smaller tonnage of sulphide concentrates containing appreciable amounts of zinc, and the zinc content of the slag rose to 10.0 pct. The Anaconda Company's slag fuming plant at East Helena, Montana, had then been in successful operation for several years, and it was immediately recognized that, while at that time the production of high zinc slag was small, if the grade held, a plant for the recovery of zinc from the accumulated slag might some day be practical. The grade not only held but became increasingly higher so that by 1946 suffcient slag had been accumulated to warrant the construction of a fuming plant regardless of future slag production from the blast furnaces, and with the removal of Government restrictions on construction at the end of the war the project was undertaken. The general design of the plant follows that at Bunker Hill, with waste heat boiler, unit coal pulverizers and even more extensive instrumentation and automatic control. The area around the lead blast furnaces is rather congested, being cut off from the nearest feasible site for the fuming plant by the copper plant, so that the most practical route for hot slag transfer is through the converter aisle. For this reason and also to make use of the existing converter cranes to serve the fuming furnace, an unused reverberatory at the north end of the converter building was dismantled and the fuming furnace and boiler located in its place. A flue at right angles to the furnace and boiler runs northward to the U-tube coolers and baghouse (Fig 1). From the bag-house a steel flue runs eastward to an existing and long unused 300 ft con- Crete stack. The coal handling system and de-leading plant lie north of the furnace and east of the cooling tubes and baghouse. The furnace is conventional, 8 X 21 X 33 ft high inside and completely water jacketed (Fig 2). There are 21

Jan 1, 1950