Search Documents

By John Owens, Wayne Howie, Hamid Maleki

After an analysis of the hazards of room-and-pillar retreat mining systems, it became apparent that safety could be significantly improved by considerations of (1) human factors, (2) remotely controlled mobile roof supports (MRS=s), (3) mine layout designs, and (4) ground monitoring systems. Initial studies of the effectiveness of MRS=s focused on their interaction with mine strata and evaluations of suitable measurements for detecting roof stability problems during pillar extraction. These studies indicated that overall stress distributions and strata movement were most influenced by the stiffness of coal-measure rocks and the design of mining layouts. Thus, to improve worker safety, mine layouts should be carefully designed and a pillar extraction method chosen for specific geologic and stress conditions. Pillar failure was often associated with an increase in pressure on the hydraulic gauges of the MRS, and roof failure was often preceded by rapid changes in the rate of roof-floor convergence. These studies led to development of a monitoring system that displays loading rate on an MRS in real time. A major MRS manufacturer cooperated in installing and testing the system on an MRS. New field studies focus on evaluating the performance of the system, measuring roof-floor convergence, and optimizing the safety of MRS operations through proper mine layout design.

By M. R. Geer, H. F. Yancey, P. S. Jacobsen

Two growing problems confront the preparation engineer-still further restrictions on stream pollution and a greater proportion of fine coal as more and more continuous miners come into use. The dewatering screens, centrifuges, and settling ponds that sufficed a few years ago must often be supplemented by more effective equipment, and in some instances the finest solids are now being recovered by vacuum filtration, once considered too costly in many coal washeries. Unfortunately not all slurries can be readily filtered. Some are virtually unfilterable, and others do not permit the high cake rates needed to hold costs within reason. Often, however, these difficult slurries can be rendered filterable by flocculation. Starch and lime have long increased settling rate in thickeners and can also aid filtration. More recently there have been other flocculants, primarily synthetic polymers or gums. Reports of their great effectiveness prompted the U. S. Bureau of Mines to test their use in filtration as part of its program on recovering and cleaning fine coal. The object of the present work was to compare some of the newer flocculants with starch and lime and to test the reaction of different types of slurries to flocculation. Three natural slurries, three synthetic coal-clay mixtures, and five flocculants were tested, all with a laboratory filter leaf.

Jan 7, 1959

By J B. Taylor

Geographic Information Systems (GIS) are being increasingly used by the mineral exploration industry in the search for new ore deposits. A mineral exploration GIS links geological and geophysical data by virtue of their geographic location in a digital map setting. Geological and geophysical data are categorised into a number of themes or layers within a mineral exploration GIS. These layers may include polygonal information such as rock type and tenements, line information such as faults and fold axes, point information such as mines and mineral occurences, and images such as gridded geochemistry and aeromagnetics. A mineral exploration GIS is a powerful tool to help the explorationist comprehend the spatial associations and interrelationships of his/her data. These spatial associations can be integrated with a mineral genesis model, to create a mineral prospectivity map to more effectively target exploration. Arguably a competent geologist who has a good understanding of the genesis of the local ore deposit types and knows their local geology backwards could intuitively derive a mineral prospectivity map. However, in an era of rapid data accumulation from many different disciplines, the ability to assimilate and understand is a huge task for any individual. A mineral exploration GIS enables the explorationist to spend more time analysing data and testing ideas, rather than finding and manipulating data into compatible formats.

Jan 1, 1994

By Stephen G. Hardcastle

3D-CANVENT is a software package that integrates advanced computer aided design (ACRD) true 3D graphics with a mine ventilation simulator. The package runs as a Windows(tm) application to access its printer drivers environment and does not need third party CAD software. It is composed of two primary modules: DMVENT and MINEDESIGNER. DMVENT is a traditional Fortran coded Hardy-Cross iterative ventilation network solver written in 1980 with thermodynamic capabilities. This module is relatively unchanged with the traditional data input options for branch type, specified or calculated resistances, fixed flows, and fixed or variable pressure fans. MINEDESIGNER is the graphics engine that optimizes the ventilation design process. It performs the front-end transformation of input data entered in the graphical interface into the correct format for the solver. At the back-end it reconverts the historically standard tabular data output from the solver into an easily viewed graphical format. ACRD features of MINEDESIGNER are used to generate a 3D wire-frame node and branch network of the mine's ventilation system. The network can be displayed in up to 4 views orientated to XYZ planes or a 3D view. All the views have zoom, pan, slice and rotate options. The graphical interface efficiently permits data entry and editing via a mouse with pick-and-point item selection. Branches can be found or added with "search" and "join" options. Visual interpretation is enhanced by the 16 colour options for branches and numerous graphical attributes. Network locations are readily identified by alpha-numeric names for branches, junctions and fans, and also the logical numbering of junctions. The program is also readily expandable for pollutant simulation and control/monitoring applications.

Jan 1, 1995

By Min Chen, Qinghua Liang, Weishan Yan, Yuan Feng, Shigang Wang

Various coal mine robots (CMRs) and unmanned aerial vehicles (UAVs) are implemented to explore unknown mines for improving the safety and efficiency of mining. It is challenging for CMRs and UAVs to achieve accurate positioning due to the absence of the Global Positioning System (GPS), poor lighting conditions, and similar geometric features in complex mine scenes. LiDAR-based localization and mapping methods are more accurate than others, while long-time running in large-scale scenarios will introduce nonnegligible cumulative errors. This study presents a semantic-aided Li- DAR simultaneous localization and mapping (SLAM) with loop closure, which leverages the uniqueness of mine intersection structure to establish stable semantic loop closure. Specifically, we propose a semantic intersection descriptor of translation and rotation invariance, which encodes 3D point clouds of the same intersection from different positions and viewpoints into a unified image. By using the semantic descriptor, we can construct a constant loop constraint when the same intersection is revisited from different directions to reduce cumulative drift. We provide experimental validation using large data sets collected in two large underground mines, namely, a simulated Edgar mine deployed in ROS Gazebo and a public underground mine data set provided by ETH. Experimental results show that the proposed method has higher localization accuracy and outperforms the existing LiDAR-based SLAM strategies.

Feb 1, 2024

By R. J. Shanley

This report presents a computer code that has been developed by the Bureau of Mines for isolating naturally occurring clusters of data plotted on the unit hemisphere and testing these clusters against a probability distribution which admits elliptical symmetry about its mean. A listing of the computer code is provided along with an example output illustrating the delineation and analysis of clusters in fracture orientations measured in a porphyry copper deposit.

Jan 1, 1975

By J Aydin Bilgin, Sedat Esen

This paper describes the ideality of some commercial explosives with the help of the detonation theory and detonation velocity measurement. Ideality of an explosive can be determined by comparing experimentally measured and ideal detonation velocities. A measured detonation velocity at a certain charge diameter markedly lower than the ideal value indicates incomplete reaction and thus non-ideal detonation. Since it is shown that commercial explosives exhibit non-ideal behavior, two-dimensional detonation theory should be used to evaluate the performance of explosives. This theory enables to compute the detonation properties of explosives (detonation velocity, detonation pressure, etc.) as a function of charge diameter and confinement. The use of the one-dimensional detonation theory to compute the detonation properties for commercial explosives has an error associated with it as these calculated properties are independent of charge diameter and confinement. It assumes that shock front is planar. Hence, it is incapable of assessing the ideality of the explosives due to its assumptions. Shock front in real situation is curved in shape but not planar as in one-dimensional detonation theory. In this paper, the non-ideal behavior of some commercial explosives is modeled using EXRINT code based on the steady-state two-dimensional detonation theory firstly. Then the degree of ideality of each explosive found from the code is checked using detonation velocity test results conducted at a quarry. It has been shown that idealities of the tested explosives determined by the code agree well with the field detonation velocity test results.

Jan 1, 1999

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,' it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By Adilson Curi

"A fundamental aspect in the development of any open-pit mining project is the determination of the mineable mineral reserves, obtained with the design of the so-called ultimate pit limits. In this paper, firstly the Vulcan software applied over the data of MR phosphate deposit will be introduced. Modeling of the ore deposit has been done by geostatistical and conventional methods by using geological data of 41 diamond core samples. Insitu geological reserves were estimated to a level of accuracy to support detailed mine planning. Ore body has been divided into regular three dimensional fixed blocks. The ultimate pit limits of the model deposit weredetermined by the vulcan program by an optimizing technique. Additionally, the approximate location of the deposit and drillholles and the contour map of the ultimate pit limits generated by the vulcan program are presented. "

Jul 17, 2000

By Charles Baskerville

SHALES containing,"kerogen,," or bituminous matter, which on destructive distillation yield oily and tarry matters resembling petroleum are here designated as oil-shales. They differ from oil-bearing shales from which petroleum may be obtained by so-called mechanical means. The educts obtained by the destructive distillation resemble some or all the varieties of petroleum, depending on the character of the shale and the mode of treatment. Some shale oils have e a paraffin base, some an asphaltic base, or a combination; some run high in sulfur compounds, The methods of refining and cracking, therefore, are essentially the Sam as are used in refining petroleums. In 1860, in this country, over fifty companies were successfully distilling various bituminous natural materials for the production of "coal oil," used for illuminating purposes. The discovery of petroleum and the failure of these companies to save and utilize the valuable byproduct, ammonia, brought about their inevitable doom. Prior to that time, more or less successful efforts were made to produce from the shales of Scotland oils for illuminating and heating purposes. Competition of native petroleum from the United States early eliminated some of these companies and with the entrance of oil from the Russian and other fields into the world's markets, the Scottish oil-shale industry underwent serious and trying experiences until, in 1916, only four (Scottish) were paying concerns.. These survived only through energy and the application of skill in saving valuable byproducts. A few companies have successfully operated in France and New Zealand. The Canadian Government showed active interest in the New Brunswick shales, which exist in quantity and are more valuable than the Scottish shales. The retarded development of that very valuable asset of the Province of New Brunswick involves a pathetic history, which is lamentable. This was especially true when the product was so much needed in the prosecution of the war. The economic success of a shale-oil industry depends on the following factors:

Jan 6, 1919

By J Pan, Q H. Li, D Q. Zhu, C C. Yang, X Wang, Z Q. Guo

Al2O3 in natural iron ores generally occurs in goethite, kaolinite, gibbsite, hematite and iron carbonate. When the content of alumina in sinter increases from 1.11 per cent to 3.50 per cent, the reducibility of sinter decreases with the addition of four different types of alumina. When gibbsite and kaolinite are added, the low temperature reduction disintegration (RDI+3.15 mm) of sinter increases with the increase of Al2O3 content in the range of 1.5 per cent to 3.5 per cent. Furthermore, when adding pure reagent alumina, the increase of Al2O3 content in the range of 1.5 per cent to 3.0 per cent will increase the RDI+3.15 mm of sinter. The addition of ferric oxide–alumina spinel with the Al2O3 content in the range of 1.5 per cent to 2.5 per cent, also increases the RDI+ 3.15 mm of sinter. The influence difference is results from the change of the mineral composition and microstructure of sinter because of the occurrence state of Al2O3. Under the condition that Al2O3 content of sinter is 2 per cent, the porosity of sinter with kaolinite is 37.26 per cent, and the shape is irregular. When gibbsite and ferric oxide–alumina spinel are added, the porosity of sinter is about 16 per cent, and the pores are round. When pure reagent alumina is added, the porosity of sinter is 17.49 per cent, and the pores are regular and small. When kaolinite, gibbsite and ferric oxide–alumina spinel are added, platy calcium ferrite is mainly formed in the sinter, and some of it is columnar calcium ferrite. On the other hand, when pure reagent alumina is added, in addition to platy columnar calcium ferrite, acicular calcium ferrite is also formed in the sinter.

Nov 8, 2021

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By Boyd D. M

Minor magnetic anomalies which may be un represented on a magnetic contour map can be extracted from the original survey data and plotted by the described method to provide a rapid interpretation of the magnetic survey, provided that the data has been recorded digi- tally on magnetic tape. The example used comes from 40 kilometers south of Charters Towers, Queensland.

Jan 1, 1977

DESCRIPTION OF OREThe ore consists, in general, of a very finely grained mixture of sphalerite, galena, and pyrite, with a gangue of quartz and schistose material, and contains about one ounce of silver to the unit of lead.Minor minerals are chalcopyrite, tetrahedrite, and ruby silver. The amount of gangue within the ore-bodies themselves is usually less than 20% of the weight of the whole. The ore is banded in a way that corresponds to the structure of the original schists, and is by no means uniform in composition-at one point, for example, blende may predominate, and a few feet farther on the body may become highly pyritic.Owing to the intimate association of the mineral constituents of the ore, it is very difficult to separate them from one another.Although this remark applies to ore from all parts of the field, the difficulty is particularly noticeable with Rosebery ore, the minerals of which are more intimately mixed, and are of smaller grain size than are the minerals of the Hercules ore.To effect a reasonably clean separation, it is necessary to grind the ore so that 90% passes a 200-mesh I.M.M. screen. Microscopic examination of the crushed product shows that 85% of the minus 200-mesh material is less than 30 microns in diameter, or, in terms of screen sizing, is minus 400 mesh. Particles under 30 microns are found to consist, of one mineral only, but in particles over this size separation has not always been effected. For instance, it is known that part of the galena and of the pyrite in the zinc concentrate is associated with sphalerite, and that part of the galena in the mill residue is associated with pyrite. There is only slight association between the minerals in the lead concentrate.

Jan 1, 1927

The OptiPit® software program is developed based on expertise gained at the Colorado School of Mines (CSM) using Mixed Integer Linear Programming (MILP) techniques. This program has been developed to satisfy the need in the mining industry for a multi-time period schedule and cutoff grade optimization tool that handles large scale open pit and underground mining operations involving many dumps, stockpiles, complex processing options and blending requirements. The current software (or earlier development versions) has been beta tested and used on various large scale projects within Placer Dome Inc., Newmont Mining Corporation, and Phelps Dodge Corporation since 2003. Through the use of this software, these companies experienced additional value creation by optimizing mine sequences, cutoff grades, material process flows and stockpiles under complex operational and processing constraints. This paper will present simple case study results to demonstrate the power of OptiPit® when used as a cutoff grade optimization tool. Furthermore, the paper will show, by example, how significant the difference in the Net Present Value (NPV) of a given project can be, depending on whether results are obtained by way of cutoff grade optimization using OptiPit®, or by using traditional breakeven cutoff grade approach.

Jan 1, 2007

By J. B. Scuffham, G. A. Rowden

The use of ammonia as a leaching agent has been well-documented but only recently have its advantages been fully exploited on a commercial basis. When compared with conventional sulfuric acid leaching processes, the major advantage of ammoniacal systems is their ability to reject iron and many acid consuming gangue materials. Although metallic copper, nickel, zinc, etc. are dissolved rapidly in ammoniacal liquors at ambient temperature in the presence of air the sulfide ores of these metals are more resistant to this treatment. Sherritt Gordon Mines in Canada treats sulfide concentrates at its Fort Saskatchewan plant under pressure with ammoniacal am- monium sulfate solution to solubilize the non-ferrous metal values. Typical leach operating conditions are 80-95°C and 115- 128 psig. Although the metals present in the ammonical solution could be recovered via solvent extraction techniques, Sherritt Gordon Mines currently operates a pressure reduction process using hydrogen to yield metal powders directly from the ammoniacal solution. The basic Sherritt Gordon technology has been applied world wide for the treatment of nickel/cobalt concentrates.

Jan 12, 1973

By The DY125-33(Leg 2) Science Parties, Chuanshun Li, Xuefa Shi, Bing Li

"The slow-spreading Mid-Atlantic Ridge (MAR), with a length of ~1.26*104km (Bird, 2003), is the longest mid-ocean ridge on this plant. Separated by the large, left-stepping Equatorial fracture zones, it then be divided into two approximately equal-length parts: Northern Mid-Atlantic Ridge (NMAR, ~6292km) with an average spreading rate of 24mm/yr, and Southern Mid-Atlantic Ridge (SMAR, ~6332km) of 33mm/yr (calculated from PB2002 model, Bird, 2003). Previous works (e.g. Fouquet 1997, Hannington et al., 2011) suggest that slow-spreading ridge could support hydrothermal activities and further favorable for the development of extensive seafloor massive sulfide deposits (SMS). Unlike the NMAR for which large part has been explored for SMS (Hannington et al., 2011; Beaulieu et al., 2015), the SMAR is amongst the least hydrothermal explored spreading ridges until now (Haase et al., 2005, Beaulieu et al., 2015), though both of them show significant similarities in terms of spreading rate, ridge morphology, segmentation, etc. (Macdonald et al., 2001, Sandwell et al., 2014, Tucholke et al., 2008).Before this work, several hydrothermal cruises had been to SMAR since British and German programs starting in 2002, some hydrothermal fields, along with systematic geophysical data, were newly investigated, and types of geologic setting that can host hydrothermal activity were firstly identified (e.g. German et al., 2008; Haase et al.,2005; Haase et al.,2009; Devey et al.,2010; Schmidt et al.,2011).."

Jan 1, 2017

By Claudio Sulca, Fernando Salas

Como parte de la política de mejora continua de nuestra compañía y de nuestro proceso de gestión de activos, uno de nuestros principales objetivos es lograr que nuestros activos alcancen y superen las horas de operación y ciclo de vida estimados en nuestro plan de negocios, asegurando la confiabilidad y buscando un equilibrio con los costos de reparación y costos horarios de rendimiento. Uno de los procesos importantes para lograr este objetivo es el proceso de monitoreo de condiciones, el cual asegura la salud y confiabilidad de los activos.

Sep 30, 2022

By N Clarke, R Dineen, W Jones

The Mt Lyell copper mine in western Tasmania has discharged acid drainage (AD) into the Queen and King Rivers and Macquarie Harbour for over a century. Presently, dissolved copper loads of about 1000 tonnes per annum and dissolved aluminium loads of >2000 tonnes per annum are contained in the AD, which is derived from underground workings (~60 per cent) and historic waste rock dumps (~40 per cent). Flows vary from about 100 L/s during dry periods, to >400 L/s during the wet winter. The site is presently operated by Copper Mines of Tasmania (CMT) who are not responsible for the acid drainage generated from the mine site. Although western Tasmania is famous for its mining history, tourism and aquaculture have emerged as the new industries on the West Coast, with a major tourism railway (the Abt) recently opened along the banks of the Queen and King Rivers. The emergence of these industries in a æclean greenÆ Tasmania has resulted in a strong community and government push to remediate the acid drainage. Remediation investigations and efforts at Mt Lyell were initiated by the Department of Primary Industries, Water and Environment (DPIWE), previously known as DELM, in 1995, and have included the quantification of environmental impacts arising from the AD, and the investigation and costing of potential remediation options. A primary focus of the work has been to identify cost-neutral options which recover metals from the AD in a saleable form to help defray on going treatment costs. This paper summarises these activities in generally a chronological order, highlighting findings of the program that are potentially applicable to other acid drainage sites.

Jan 1, 2003

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

THE problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce light-weight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough so that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, particularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating." The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. Commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the purpose of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942