Search Documents

By A. Karami

It is well established that an ordered sequencing of charge initiations in a blast pattern is an important design consideration that affects blasting performance. Delay times must be chosen such that damage to the rock mass is controlled. The accuracy of delay detonators is also of major concern. A large scatter could lead to an incorrect blast sequencing that would lead to damage to the rock mass causing increased over-break, degraded fragmentation, increased fly-rock and poor vibration control. In this study, the effect of using accurate delay detonators on the explosive energy generated is investigated. For this purpose, power spectral density of the blast vibration for delayed shots are calculated and compared with the case where holes are shot at the same time (no delay). At the end the results are presented and discussed.

Jan 1, 2000

By A. F. Crawley

The density and viscosity of 1iquid thallium have been measured by absolute methods to temperatures of about 200° and 150°C, respectively, above the melting point. These new data reported, especially density data, do not closely confirm previous work. Density p, in g per cu Cm, is shown to vary linearly with temperaluve t, in °C, according to the equation p = 11.658 - 1.439 X l0-3t. The viscosity data obey the well-known Andrade equation nv1/3 = A exp C/vT , the constants A and C for thallium having values of 2.19 x A and 79.648, respectively. This paper reports some new data for the density and viscosity .of liquid thallium. Measurements of these fundamental physical properties were undertaken as part of a continuing research program at the Mines Branch, Department of Energy, Mines and Resources, Ottawa. Canada. A literature search has revealed that data are so scarce that there could not be a consensus on the true values of the density and viscosity of liquid thallium. To be more specific, there exists only one set of viscosity data' and only two acceptable sets of density data,273 one of which is limited in scope.3 In Liquid Metals Handbook,3 another density study is reported but indications of impurities in the thallium render the results suspect. In this situation, further careful experimentation was required to realize the true density and viscosity of thallium. EXPERIMENTAL METHODS Density. Densities were determined using a graphite pycnometer. The technique and its accuracy have been discussed in earlier papers.4'5 It is considered that experimental data can be obtained which are accurate within +0.05 pct, all sources of random and systematic errors having been evaluated. Density results for thallium were identical whether measured under an atmosphere of argon or a vacuum of 5 x 10-6 torr and, for the most part, the argon atmosphere was used. Viscosity. Viscosity measurements were made in an oscillational viscosimeter by an absolute method—the liquid metal being held in a closed graphite cylinder. Design and operation of the apparatus, constructed in this laboratory, have previously been discussed.6 For thallium, runs were made under a vacuum of about 2 x 10-6 torr. To evaluate viscosity coefficients from the various experimental parameters, the mathematical analysis of Roscoe7 was used. Measurements of the necessary parameters and the accuracy of these measurements have also been discussed.6 The cylinder dimensions were corrected for the anisotropic expansion of graphite, as discussed for density measurements.4,5 It is well-known that thallium oxidizes rapidly and hence a newly machined surface quickly tarnishes in air. The oxide film, however. is nonadherent and is easily removed by rubbing or by solution in water. Hence, immediately before use, both density and viscosity charges were immersed in water, wiped dry, and quickly transferred to the apparatus which was then rapidly evacuated. Specimens removed after determinations were only slightly tarnished and there was no other evidence that tarnishing affected the results. For example, the sharpness of the specimen edges from the containing vessels indicated complete filling by the liquid metal. Thallium of 99.999 pct purity was used in this investigation. Because of its high toxicity care was exercised in handling this material. For example, the melting procedure to prepare machinable ingots was carried out in an open, well-ventilated area, while protective gloves were always worn when handling the solid metal. RESULTS AND DISCUSSION Density. Measurements were made over a tempera-ture range of about 200°C above the melting point. The results are listed in Table I and plotted in Fig. 1. From the graph it is evident that the relation between density and temperature is linear. Such a relation has been observed before in this program for other metals and alloys475 and elsewhere by other workers. A least-squares analysis of experimental data gives the equation: pT1 = 11.658 - 1.439 x 10-3t where p = density in g per cu cm and t = temperature in "C. In Fig. 1, together with the present results, the data of Schneider and Heymer2 in the corresponding temperature range have also been plotted. Evidently, the two sets of data do not agree well, the results of Schneider and Heymer being about 0.6 pct higher. Viscosity. Viscosity data were obtained from the melting point, 303.5°C, up to 457.5"C. The data are listed in Table I and in Fig. 2 the plot of these results demonstrates a smooth curvilinear relation between

Jan 1, 1969

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

The aim of this paper is to evaluate the suitability of a coal sample from the mine Jaworzno (Poland)- locality for bacterial leaching. Laboratory research used a pure bacterial culture of Thiobacillus ferrooxidans. The results showed that bacterial leaching was effective, with a one month leaching time, when 65% of total sulphur and 85% of pyritic sulphur was leached. The paper describes changes to the pyrite during and after bacterial leaching.

Jan 1, 2003

By L. Andrews

Keywords: mineralogy, phase-chemical, chemical-looping combustion, XRD, SEM, EDS, QEMSCAN, PGM, slag, matte, ilmenite Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution. Mineralogical applications are described from pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By J. R. Long, T. R. Graham, R. S. Dean

ALTHOUGH considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to 11 pct aluminum, with some incidental information on the single-phase alpha solid solution alloys. Strauss1 gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper5 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50° temperature levels from 400° to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solubility of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 1300°F and higher,

Jan 1, 1947

By W. Jolley

Decarburized iron and Fe-3.28 pct Ni alloys were impact and tension tested in the temperature range of ambient to 4°K. It was found that alloying with nickel improves the fracture properties of the ferrite matrix. The improvement in toughness of iron alloyed with nickel is attributed to the effect of the nickel addition on the temperature and strain rate dependence of the yield stress as well as on slip behavior. The Fe-Ni alloy exhibits wavy slip when strained at temperatures down to at least 50°K. This behavior contrasts with that of the unalloyed iron where a change It is a generally accepted fact that of the common alloying elements of steel only nickel and manganese improve both the room-temperature yield strength and the notch impact properties. It has been argued for a number of years that manganese refines the ferrite grain size, the pearlite spacing, and the grain boundary carbides in medium- and low-carbon steels and thereby increases resistance to brittle fracture.''' This hypothesis recently was confirmed for a 0.04 pct C iron containing manganese, but at the same time from wavy to planar slip occurs at about 120°K. The observed lower temperature and strain rate dependence of the lower yield stress in the Fe-Ni alloy as compared to the unalloyed iron may be attributed to this difference in slip behavior. In contrast to suggestions published previously, transmission electron microscopy showed that the uniform dislocation distributions and the lack of dislocation tangles which are produced by low-temperature straining of bcc materials cannot be attributed to the absence of cross slip at these temperatures. no increase in notch toughness was observed in a decarburized Fe-Mn alloy.3 It thus appears that manganese only increases the toughness of Fe-Mn-C alloys by refining grain boundary carbides and has no toughening effect in carbon-free iron. On the other hand, the mechanism whereby nickel improves toughness has not been established. Hodge et a1.4 have clearly shown that a 3.28 pct Ni addition lowers the impact transition temperature of 0.02 pct C steel approximately 35°C when the grain size is maintained constant. Recently, Wullaert and Tetelman6 stated that nickel refined the grain boundary carbides of an Fe-C alloy and consequently increased the toughness. They also observed the previously reporteda-'

Jan 1, 1969

Contracts are widely used in mining to provide self motivation in an environ-ment of isolated work places. Which incentives to use and how to implement them has long been the subject of numerous discussions. The mines operated by Australian Mining and Smelting at Broken Hill have evolved several guidelines to follow when developing contracts.Identify the main purpose of the work and use this as the basis of measurement for the contract. Therefore stoping achievement would be measured by tonnes extracted, development by metres driven. Paying for other work activities such as standing timber in timber stoping must detract from the percentage of the total contract paid per tonne produced. Concentrating on the main activity and applying the majority of contract pay to that task reinforces at is beneficial to both the miners and the whole operation.

Jan 1, 1985

By F. E. Katrak

Rare earths markets by definition usually include not only the rare earth elements, but also yttrium. They can be subdivided into a very large light rare earth fraction (about 95 percent by weight of all rare earths consumed) consisting mainly of cerium and lanthanum and a smaller fraction (with much higher unit value) consisting of selected high-purity oxides or elements such as yttrium, europium, samarium, or neodymium. CRA estimates that the noncomnunist world market for all rare earths and yttrim was on the order of US$750 million in 1986. The main focus of this paper is on the principal uses for rare earths, some CRA-developed proprietary data on their consumption by region, and the selective nature of business opportunities in the rare earth markets. We also provide forecasts on the future trends in these markets.

Jan 1, 1989

By T. R. Graham, R. S. Dean. J. R. Long

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By R. S. Dean. J. R. Long, T. R. Graham

Although considerable information has been published concerning manganese additions to the aluminum bronzes, these data refer principally to the two-phase alloys containing 8 to II pet aluminum, with some incidental information on the single-phase alpha solid solution alloys. Straussl gives an excellent review of the literature on aluminum bronzes up to 1927 and a bulletin2 of the Copper Development Association brings the bibliography up to 1938. The most extensive work on manganese addition is that of Rosenhain and Lantsberry,3 who investigated alloys ranging up to 10 pct aluminum and up to 10 pct manganese, and presented data on the physical properties of sand-cast, chill-cast, and several wrought alloys. The greater portion of the work, however, concerns alloys ranging from 7 to 10 pct aluminum in the cast condition and sheds little light on the properties of wrought single-phase alloys. Corson4 notes that alloys containing 10 pct manganese and 4 pct aluminum are not hardenable by heat-treatment, while one with 15 pct manganese and 5 pct aluminum can be hardened, but he gives no tensile data on it. In fact, no systematic study of the properties of single-phase wrought alloys containing substantial amounts of manganese has been reported. It should also be noted that most of the investigators worked with alloys containing significant amounts of iron and silicon, and that these impurities, whether intentionally added or accrued from the raw materials used in the preparation of the alloys, may be expected to have a direct bearing on the resultant properties. In the work on alloys made with electrolytic manganese, the Bureau of Mines has undertaken an investigation of the copper-manganese-aluminum system for the purpose of establishing the constitution and properties of high-purity alloys. In a recent paper6 the authors reported a metallographic investigation of the alpha solid solution area and the adjoining fields of the copper-manganese-aluminum system up to 50 pct manganese. This study established the alpha-phase boundaries at 50" temperature levels from 400' to 850°C. It was found that the addition of manganese to copper-aluminum alloys decreases the solub%ty of aluminum in the alpha phase (Fig I), curving the boundary toward the copper-manganese base line. The greatest change occurs in the first 20 to 25 pct manganese, which decreases the solubility of aluminum to approximately 4 pct. With larger amounts of manganese the alpha boundary tends to parallel the copper-manganese binary. At 13oo'F and higher,

Jan 1, 1947

By D. L. Ogonowski, J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m(36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached design capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM-800Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By A. C. Beaulieu

CITY OF EDMONTON Rate of Growth The City of Edmonton has been classed by some economists as being the most progressive City in Canada since the early 50's. The high rise buildings that are changing Edmonton's skyline, the rapidly expanding sewer and water network, and the proposed rapid transit system all indicate the requirements of an ever expanding City. Edmonton, the core of Canada's Energy Empire is the country's seventh largest metropolitan area. Bisected by the 22 mile long park of its magnificent river valley, it sits in the midst of the 50,000 sq miles of riches that have created it. Underneath the City, however, extending down for thousands of feet and encircling it for a radius of scores of miles, lies a fabulous store of petroleum wealth. By the early 1940's, based upon the needs of the farming areas, accompanied by some small exploitation of coal and timber, Edmonton grew to 100,000 people. Then in a short space of 20 years Edmonton shot up to be a city of 450,000. Figure 1 (Slide No. 1) indicates the population growth in the City of Edmonton and the Census Metropolitan Area from 1906 to 1971.

Jan 1, 1997

By Mauricio Monteiro Machado, Neyda de la Caridad Om Tapanes, Ana Isabel de Carvalho Santana, Rodolfo Salazar Perez, Rodrigo Ribeiro Soares, Roberta Gaidzinski

Vasos de pressão são equipamentos empregados nas mais variadas indústrias, sendo responsáveis por significativa parcela do orçamento. Os materiais mais utilizados para a construção de vasos de pressão para a indústria de óleo e gás são as ligas de aço carbono e em alguns casos se justifica o emprego de ligas de aços inoxidáveis. O objetivo deste trabalho foi estudar as características dos vasos de pressão, materiais de fabricação e o custo de aquisição de vasos de pressão por parte da Petrobras. Para o desenvolvimento foram utilizadas duas ferramentas de processamento de dados: a Lei de acesso à informação que permitiu a criação de uma base de dados, e o Planejamento de experimentos que possibilitou avaliar a influência do tipo de material e outras variáveis sobre o preço do vaso de pressão (variável de resposta). Os resultados estatísticos demonstram que, para as faixas analisadas o comprimento entre tangentes (CET) e o Diâmetro (D) possuem uma influência estatística direta sobre a variável de resposta Preço. Finalizando, o estudo conseguiu conciliar aspectos construtivos com os fatores financeiros, sendo de grande valia para os fabricantes de vasos de pressão.

Aug 1, 2019

By Braden T. Lusk, Rex A. Meyr, Kyle A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by MSHA and required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. A polycarbonate safe haven wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed in both half-scale and small scales in the University of Kentucky Explosives Research Team’s (UKERT) explosives driven shock tube. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to blast pressure. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into the finite element program and modeled to compare deflections of each part to that was measured during testing for model validation. This paper summarizes the results.

Jan 1, 2014

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By Christopher P. White, John R. Wagner

This paper will discuss the complex and difficult soil conditions encountered in the sinking of 15 shafts of 18m to 27m depth and the excavation and lining of 6700m of 2.74m dia. interceptor sewer on Staten Island, New York. The complex soil profile consists of dense glacial till and sand outwash strata overlying the much older cretaceous sand, silt and clay strata. The tunnel varies from 8m to 14m below the nearby sea level. A significant amount of boulders were anticipated in the till. therefore, a decision was made to excavate the tunnel with a digger shield installing bolted, gasketed concrete segments. The bid documents stated the soils were dewaterable. Several conditions occured in this complex soils matrix which required modifying the planned means and methods including the necessity to use compressed air. The conditions encountered and the equipment used will be described.

Jan 1, 1991

By A. B. Kinzel

THE demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low tempera-tures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selec-tion of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low tempera-tures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120° C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By J. T. Crawford

The purpose of this paper is two fold. It will: (1) examine leasing analysis as a project evaluation criterion, and (2) compare the cost of leasing with other methods of financing. The use of leasing has grown extensively in recent years as a method of obtaining equipment. The computer industry has been highly dependent upon leasing from its earliest days to dispurse its equipment to the customer, while airlines and railroads acquire large segments of their aircraft and rolling stock by leasing. Over the last few years the mining industry has leased haulage trucks, bulldozers and other equipment of similar nature.

Jan 1, 1974

By E. N. Smith, J. C. Redmond

The increasing need for materials capable of withstanding higher operating temperatures for various applications such as gas turbine blading and other parts, rocket nozzles, and many industrial applications, has brought consideration of cemented carbide compositions. The well known usefulness of cemented carbides as tool materials is attributable to their ability to retain their strength and hardness at much higher temperatures than even complex alloys. However, it has been found that the temperatures encountered in cutting operations do not approach by several hundred degrees1 those involved in the applications mentioned above where the interest is in materials possessing strength and resistance to oxidation at temperatures of 1800°F and above. At these latter temperatures, the tool type compositions which are made up essentially of tungsten carbide are found to oxidize very rapidly and to produce oxidation products of a character which offer no protection to the remaining body. As a further consideration, the density of the tungsten carbide type compositions is high, from about 8.0 to 15.0. The refractory metal carbides as a class are the highest melting materials known as shown by Table 1 which summarizes the available data from the literature for the carbides of the elements which are sufficiently available for consideration for these uses. The density is also included in the table, since as mentioned above it is an important consideration in many of the applications for which the materials would be considered. It has been established that in the tool compositions the mechanism of sintering with cobalt is such as to result in a continuous carbide skeleton and that the properties of the sintered composition are thus essen- tially those of the carbide.2 On the hypothesis that this mechanism holds to a greater or less degree in cementing most of the refractory metal carbides with an auxiliary metal, it appears from Table 1 that titanium carbide compositions would offer possibilities for a high temperature material. Titanium carbide has extensive use for supplementing the properties of tungsten carbide in tool compositions. Although the literature contains several references to compositions containing only titanium carbide with an auxiliary metal,3,4,5,6 it may be inferred from the meager data that such compositions were deficient in strength and were considered to have poor oxidation resistance.7 Kieffer, for instance, reports the transverse rupture strength of a hot pressed TiC composition at 100,000 psi as compared to up to 350,000 psi for WC compositions. The work described herein was undertaken to determine the properties of compositions consisting of titanium carbide and an auxiliary metal and to improve the oxidation resistance of such compositions. It appeared possible that the inclusion of one or more other carbides with titanium carbide might improve the oxidation resistance and also that this might be more desirable than other means from the point of view of maintaining the highest possible softening point. Consideration of the available carbides in Table 1 suggests tantalum and columbium carbides because of their high melting points and general refractoriness. The work on improving oxidation resistance was concentrated on the addition of tantalum carbide or mixtures of tantalum and columbium carbide. The auxiliary metals used included cobalt, nickel and iron. It was also desired to learn the general physical properties of these compositions. Experimental Procedure The compositions used in this study were made by the usual powder metallurgy procedure applicable to cemented tungsten carbide compositions. The powdered carbide or carbides and auxiliary metal were milled together out of contact with air. In some cases cemented tungsten carbide balls and in other instances steel balls were used to eliminate any effect of tungsten carbide contamination. A temporary binder, paraffin, was then included in the mix and slugs or ingots were pressed with care to obtain as uniform pressing as possible. The ingots were presintered and the various shapes of test specimens were formed by machining, making the proper allowance for shrinkage during sintering. Thereafter the shapes were sintered in vacuum at temperatures of from 2800 to 3500°F. Final grinding to size was carried out by diamond wheels under coolant. The titanium carbide used contained a minimum of 19.50 pet total carbon and a total of 0.50 pet metallic impurities as indicated by chemical and spectrographic analysis. It was found by X ray diffraction examination with

Jan 1, 1950

By T. D. Tiemann

The caustic extraction of silica from Wisconsin and Minnesota taconite was investigated by bomb digestion over the temperature range from 312 to 40S°F at caustic concentrations from 25 to 500 gpl. Residual concentrates containing as much as 65 pct iron were obtained. The high rate of silica extraction is related to a microcrystalline variety of quartz, since it is shown that the rate of extraction of silica from quartz is directly proportional to its surface area. Increasing dependence on foreign ore reserves makes the need for developing the technology necessary for treatment of our low grade ores even greater than it was at the time of World War 11, when much research was conducted on the extraction of alumina from clays. Representative of these were the studies carried on at the University of Illinois.' More recently, the U. S. Bureau of Mines investigated the production of alumina from anorthosite, and currently the aluminum industry is showing renewed research interest in this field. The studies reported here are part of a continuing research program based on the above concepts and aimed at the eventual development of processes for the treatment of low grade ores, particularly those of iron. The fact that large reserves 3 of low grade nonmagnetic taconite are contained in the iron formation of the Wisconsin Gogebic range have made this ore an important and attractive target for investigation. The idea of removing silica by caustic extraction is not new.495 The digestion in caustic solution of ground flint, diatomite, and other forms of chalcedonic silica is the basis for the production of soluble sodium silicates by the wet-process. Upgrading bauxites by the caustic extraction of silica has been investigated6 and is the subject of a German patent.7 Although mention is made by Roe' of the caustic extraction of silica from low grade Michigan and Wisconsin iron ores, and he lists a number of patents and references on the subject, recent work in the field does not appear to be extensive. As far as the author knows, there has been no work in this field on these particular ores. It is hoped that this paper will stimulate further investigation which will eventually lead to an econclmic means of processing these large low grade reserbes. TACONITES The taconites investigated in this study were from Minnesota and Wisconsin. That from Minnesota, a semi-taconite, Nas obtained from the Oliver Iron Mining Division, U. S. Steel Corporation, and represents a sample of an oxidized iron formation from their King Mine on the Mesabi range. The Wisconsin taconite came originally from the trench sampling of the U. S. Bureau of Mines, and represents a composite of the Norrie, Pabst, Yale, Plymouth, and Pence members of the Gogebic iron formation. Assays on these samples are given in Table I. A typical calcu1atr:d average analysis of the Wisconsin taconite is given in Table 11. Chemically, the Minnesota semi-taconite sample contains about 39 pct iron and 39 pct silica, while the Wisconsin taconite contains 30 pct iron and 53 pct silica, both on the dry basis.

Jan 1, 1962