Search Documents

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By William X. Chavez

The Mantos Blancos copper-silver district is located in northern Chile about 45 kilometers northeast of Antofagasta, as shown in Figure 1. Disseminated and veinlet copper and copper-iron sulfides containing economically significant silver values are hosted by andesitic to rhyolitic volcanic rocks of probable Jurassic age (Chavez, 1983). Field, mineralogical, textural and lithochemical evidence show that three major alteration types may be recognized within the district: (1) district-wide sodium metasomatism, manifested as albitization of feldspars and development of albite veinlets and pore-fillings, (2) local to widespread, incipient to intense addition (chloritization) or removal (bleaching) of magnesium and iron and (3) local to widespread, moderate to intense hematitization, usually spatially associated with bornite-digenite-covellite (as specularite) or digenite-covellite-chalcocite (as red hematite staining with or without specularite) mineralization. Carbonatization, occurring as veins, veinlets, vesicle fillings and irregular patches of calcite, varies in magnitude of development but is widespread. Sericitization of feldspars and groundmass is only locally intense yet is generally present as incipient alteration throughout the district. The district-wide albitization of the Mantos Blancos volcanic sequence has altered what were originally more potassic and calcic, less sodic, rocks to what are now more properly referred to as keratophyres (Battey, 1955; Gilluly, 1935, Hughes, 1975). The petrographic and lithochemical characteristics of the three major alteration types noted above are summarized below.

Jan 1, 1984

The Martha Hill project operates with a nett surplus of water, due to the catchment of rainwater on the tailings dam and the requirement to de-water the open pit mine. It is necessary to discharge this surplus, treated as required, to the Ohinemuri River which flows past the process plant.   The treatment plant, adjacent to the process plant, handles all effluent from the Martha Hill operation including water pumped from the mine, excess water from the tailings decant, and seepage from the tailings dam underdrains. To-date the plant has treated and discharged over 800 000 tonnes of water.

Jan 1, 1991

By J. Changsheng, Z. Youdi

Based on the criteria of maximum net present value per ton of reserves and on the optimum matching of some other essential parameters, a comprehensive optimization model of surface-mine production rate is developed using system- engineering approaches and using the theory of economy of scale. A mine is then selected to demonstrate the application of the model.

Jan 1, 2000

By Adriana de Aquino Soeiro da Silva, Joao Alves Sampaioa, Luiz Carlos Bertolino, Francisco Manoel Garrido, Marta Eloisa Medeiros

"Brazil has a large agricultural potential and its production success is related to the chemicaland physical soil characteristics. Therefore, the demand in the use of a great quantity offertilizers to compensate the low amount of nutrients in the soil includes about 40% of foodproduction costs. In order to develop economical alternatives to traditional fertilizers, rockswith potential use in agriculture will be studied. In this work the potassium rock, a greensandslate, will be chemically and structurally characterized for the development of a potassiumthermophosphate. This alternative fertilizer will be obtained based on a fusion of a ponderedmixture of potassium, magnesium and phosphate rocks to be applied in the Brazilianagriculture. Preliminary characterization results indicate that the greensand slate presents ahigh percentage of glauconite, quartz and micas.Keywords: Potassium thermophosphate, alternative fertilizers, greensand slate.IntroductionBrazil has a great agricultural potential and its production success is closely related to thesoil's chemical and physical characteristics. However, the country's soils present lownutrients content and high acidity due to weather conditions. Thus, the use of a high amountof fertilizers makes up for the soils' lack of nutrients and accounts for 40% of food productioncosts. Therefore, research on obtaining new alternative fertilizers is a constant worry due tothe increase on food demand [ 1].The lack of raw material for the preparation of NPK fertilizers in Brazil is a concern and theissue of potassium fertilizers a priority. Such a fact is because in 2008 only 608.000 tons ofKCl were produced, corresponding to just 10% of the Brazilian necessity. Thus, the use ofrocks as agricultural nutrients can contribute to reduce the need for industrial fertilizers.This way, the development of a new agricultural raw material originated from a rock thatalready exists in the country's soil is of great importance for the mineral and agriculturalsectors."

Jan 1, 2011

By C. A. Stetefeldt

The iron-ore deposits worked by this Company occur in lenses 200 to 1000 feet long and 5 to 80 feet wide, and stand at an angle of from 65' to 75, with a vertical height of 250 to 500 feet, other lenses occurring below. A number of the deposits were first worked as open pits, which in some cases were carried to the depth of 150 feet, when, owing to the weakness of the walls, underground mining was adopted. While the ore was being removed from the open pit, shafts mere in several instances sunk into the foot-wall, the intention being to mine the ore with breast-stopes of an approximate height of 20 feet, followed by underhand-stopes of the same height, leaving floors between of the necessary thickness to support the walls, or to effect the removal of the ore by means of what is known as the stall system. As the work progressed, however, it was found that the walls (which are of chlorite) were too weak to permit the working of breast-stopes 20 feet high, there being frequent heavy falls of ground from the hanging and, in some instances, from the foot. The plan of following breast-stopes with underhand-stopes was, therefore, abandoned. By working breast-stopes only, but little more than one-half of the ore could be removed, and that only at an excessive cost, the ore being so hard that power-drills with 3 1/8-inch pistons . and 6-inch stroke, working under 60 pounds of compressed air, are able to drill but 8 feet in ten hours as a yearly average, while from 6 inches to 2 feet is a common result of ten hours' drilling. It was plain that some other system of mining must be adopted, and it was proposed to sink by levels of 75 feet, carrying in the cross-cuts from the shafts and working out the ore each way from the shaft from foot to hanging, and from 15 to 20 feet in height. When this has been done, drift-sets consisting of caps and legs are set up the whole length of the opening and connected with the cross-cut; the necessary openings for ladder-ways and chutes or mills are timbered from

Jan 1, 1893

By T. I. . I. Sibbald, D. E. Jiricka

The Goldfields area on the north shore of Lake Athabasca , was active in the thirties and early fortie . In 1934, Tom Box discovered gold mineralization in quartz veins in pyritized 'granite' at the ite of what wa to become the Box Mine of the Consolidated Mining and Smelting Company of Canada Ltd . In the rush of activity that followed numerou other gold occurrences were found. the most significant of the e being the Athona and Frontier prospects which underwent underground development bur did not reach production. Probable reserve identified to date in the Box and Athona deposits amount to some 3.5 million ton grading an average 0.ITT oz gold/ton . Some 10 to 15 million tons of lower grade, po ible reserve are also reported at the Box. From 1939 to 1942, the mine produced, from underground , 64,066 ounces of gold from ore grading 0.0452 oz gold/ton at a cost of between $1.5 and $2.0 a ton. The Goldfield area is underlain by upracrustal rock intruded by mafic bodies and invaded by ·granite'. The upracru tal . thought to be of Lower Proterozoic age are characterized by a helf-type ucce ion metamorpho ed under lowermiddle amphibolire facie conditions into quartzites, quartz-mica chi ts. dolomitic marbles, diop idic calc-silicates and cordierite-anthophyllite-biotite schi t . Amphibolites of presumed igneou origin form concordant to subconcordant units up to a few ten of metre thick in the upracrustals and occur as le regular masses in the 'g ranite·. Compositionally they vary from gabbroic to granodioritic. with the more mafic varieties being most common. Granitic rocks exhibiting a variety of textural , structural and compositional characteristics underlie most of the area. Four main units are recognized: foliated (older) 'granite', 'leucogranite', feldspar augen 'granite· and pyritic mine 'granite', however, in geological mapping the e are somewhat arbitrarily differentiated due to transitional relationships and admixture of types. Although there is no unambiguous age data available for the e 'granite ' adjacent northshore 'granite' of geologically similar age yield Rb-Sr isochron dates around 2000 Ma. The area is characterized by two major deformation events of which the earliest gave rise to the dominant regional foliation and to rare minor and outcrop scale folds. This foliation which in general parallels compositional layering is folded into the major Goldfields syncline, whose axis plunges weakly to moderately outh. Related open minor folds have subvertical axial surfaces which are locally paralleled by a weakly defined schistosity. Most rock display a pronounced rodding fabric, coaxial with second fold axes and apparently the product of this deformation event. However, a note of caution is introduced into this interpretation, as the rodding fabric is also parallel to first fold axe .

Jan 1, 1986

By W. C. Smith, P. J. Hickey

After a short historical background of the process evolution, this article descvibes present-day plant facilities and operating techniques utilized for high-purity bismuth production. The plant is one of the world's largest, with an annual output of some one million pounds of refined bismutlz. PREVIOUS papers1 written by staff members of Cerro de Pasco Corp. have referred briefly to the production of refined bismuth. Since the Corporation is one of the world's foremost producers of high-purity bismuth, a detailed description of the process for extracting the metal may be of general interest. Following a short historical background of the development of the actual process, this presentation will trace the progress of bismuth from its entry into the primary smelting circuits to its concentration in electrolytic lead cell slimes. Our facilities for the treatment of anode muds will be described and the extractive methods given in some detail, with particular emphasis on the techniques which result in the production of refined metal. HISTORICAL BACKGROUND Shortly after Cerro de Pasco began smelting operations at Oroya, Peru in 1922, it became apparent that the dust carried by copper converter gas contained appreciable amounts of bismuth. Although dust collection efficiency was poor prior to building of the 550-ft stack and installation of the central cottrells in 1938, a large stock of dust was accumulated during the intervening years, having the following approximate composition: Oz. per ton Ag - 11.0 Pct Sn — 0.5 Pct Pb - 49.0 Pct Zn - 6.5 Pct Bi - 2.0 Pct Insol. - 1.5 Pct Cu - 0.7 Pct Fe - 2.3 Pct Sb - 3.0 Pct S - 10.0 Pct As - 7.5 In the mid-1920's, experimental crucible melts of this dust with carbon indicated that most of the bismuth and silver, and some of the lead, could be reduced to a fairly clean bullion. Other products were a small amount of leady copper matte and a slag high in zinc, arsenic, antimony, and lead; this slag contained some tin but only small quantities of silver, bismuth, and copper. After the laboratory results had been confirmed by operation of a small reverberatory, a dust reduction furnace was constructed. The ±10 pct Bi-Pb bullion produced from this operation was stocked until 1930, when an Oroya-designed converter type furnace3 was installed for the elimination of arsenic, antimony, and some lead from the bullion. This process concentrated the bismuth from 10 to about 60 pct. By means of the bismuth process developed4 by W. C. Smith at East Chicago (1909-1914) and the discovery of a method5 for separation of lead from bismuth with chlorine gas in 1929, it became possible to begin production of refined bismuth. Unfortunately, bismuth deleaded with chlorine always contained residual chlorides, and the removal of the chlorides by caustic soda left a lead content of 0.02 to 0.04 pct. This final problem was solved6 by substitution of air-blowing for the caustic treatment, which effectively removed all excess chlorine and gave bismuth which was practically lead-free. In 1934, a pilot electrolytic lead refinery began operations at Oroya. Lead smelting was resumed in 1935 and two years later a 100-ton-per-day lead refinery was put into service. In conjunction with the latter, the present-day Anode Residue Plant was constructed. Until 1940, the plant treated both lead anode slimes and dust reduction bullion. The dust reduction furnace was shut down in that year, and all cottrell dusts (with the exception of the product from the arsenic cottrell) were mixed with pyrite and treated in a Wedge roaster to eliminate all possible arsenic. Calcine from this operation joined the sinter plant feed; hence the bismuth from the copper and lead circuits was collected in the lead bullion and subsequently in lead anode slimes from the electrolytic lead refinery. The latter source has been the only bismuth-bearing material of any consequence entering the Anode Residue Plant from late 1940 to the present. A copper refinery began operating in 1948, and the cell mud from this plant is mixed with lead slimes and processed through the same circuit, though only a small quantity of bismuth is present in electrolytic copper cell residues. BISMUTH INTAKE Present-day routes which are followed by the new bismuth feed from its entry into the primary smelting circuits to its arrival at the Anode Residue Plant are traced schematically in Fig. 1. As illus-

Jan 1, 1962

By Eliezer Martinez-Jimenez, Gretchen T. Lapidus

"Electro-assisted reduction is an effective pretreatment to render chalcopyrite less refractory towards oxidative leaching. In this process, chalcopyrite is selectively converted to chalcocite or copper metal in an electrolytic cell under ambient conditions, while ferrous ion is leached into solution. However, the reaction velocity is hampered by the formation of a ferrous sulfide passivating layer on the solid surface, especially at elevated solid to liquid ratios. In the present work, several strategies for overcoming this problem were evaluated. On one hand, specific ligands for ferrous ion were added in order to increase its solubility and, on the other, an anode material which promotes the oxidation of the sulfide ion was chosen. Leaching tests showed citric acid to be an effective ligand for both ferrous and ferric ions and, in combination with a lead-silver anode, significantly increased the kinetics of chalcopyrite reduction and subsequent copper leaching.IntroductionAttempts to oxidize chalcopyrite at a rapid rate in aqueous solutions, below their normal boiling point, have met with difficulties because of passivation by some of its own components. An alternative line of research explores reductive pretreatment, transforming the chalcopyrite into less refractory copper phases, which can later be oxidized. A recompilation of these efforts up until 2000 was published by Dreisinger and Abed [1]. However, this practice usually requires large excesses of reducing agents, such as copper, lead, aluminum or iron, and in this last case at near-boiling temperatures, in highly"

Jan 1, 2012

The following list of US companies, mines, and mills engaged in uranium production was compiled by the Health and Safety Analysis Center, Mine Safety and Health Administration, in Denver, Colo. The list includes those companies reporting to the Center in 1978. Thanks to D. K. Walker, Chief of the Health and Safety Analysis Center, for providing the information to MINING ENGINEERING.

Jan 10, 1978

By Clement K. Chase, F. Milton Lewis, Roshan B. Bhappu

In this paper an attempt has been made to review the cost trends in producing copper by conventional milling, smelting and hydrometallurgical means during the last five years. The primary objectives of this cost analysis are to provide a base for future projections as well as to indicate which cost items are more volatile in their influence on overall cost of producing copper.

Jan 1, 1979

By Willy Ank de Morais

Historicamente a execução de fundações profundas com perfis metálicos eram prejudicadas pela falta de sincronia entre as atividades de cravação das vigas e suas emendas. O grande problema é a demora na execução das emendas, tipicamente pelo uso de soldagem com talas, que normalmente leva 1 hora para ser completada. Neste trabalho analisou-se o Caminho Critico (MCC) da operação para incrementar a produtividade na execução de fundações profundas pela adoção de dispositivos, equipamentos e processos de alta produtividade, encabeçados por soldadores qualificados e certificados. Com isso, criou-se o processo INO///FAST®, aqui apresentado, que permite obter uma emenda, atendendo plenamente aos preceitos da norma ABNT NBR 6122:1996 (“Projeto e execução de fundações”), em apenas 10 minutos. O processo desenvolvido foi analisado, verificado e comprovado em uso prático por pesquisadores, engenheiros e técnicos.

Oct 30, 2017

By S. C. Tadolini

Roof support systems have evolved from standing posts and timbers to a generation termed ?big nails? where steel bars are inserted into boreholes and anchored with expansion shells and/or resin cartridges. These systems have been effective but are limited to mining height. Additionally, the properties of steel do not resists shear forces or have the flexibility being required in difficult ground conditions. The next generation of roof support systems is coupling the best parts of the ?big nail? and resin grouted cable bolt systems. This paper will present the advanced technical solutions of the next generation of cable systems that includes an indented high-capacity PC-strand used with a variety of fixtures. Case histories of support applications will be presented.

Jan 1, 2012

Mine planning typically involves designing an operation to uncover coal with the minimum initial costs with reclamation planning and earthworks being done as an "add on" task. The landform is too steep to remain stable, has no drainage and frequently has areas of excessive acidity or alkalinity. Extensive earthworks are required to reduce grades to an acceptable level and create a drainage system. The flexibility available to the mining engineer to alter the post mining landscape clearly depends on the mining methods. Straight dragline stripping provides virtually no flexibility. However most mining operations over the term of current ten year plans have a substantial pre-strip component. It is this pre-strip material which has the potential to reduce the final reshaping earthworks. The reshaping operation itself is subject to some flexibility with various options being available to re-grade and provide drainage. The full utilisation of this flexibility to minimise earthworks cost should be the aim of reclamation design. ACIRL's current thrust in reclamation is aimed at the integration of mine planning and reclamation earthworks. This involves gathering all environment and agricultural criteria and designing the earth works necessary to produce an acceptable final landform. A key component of our work is the use of computer aided design (CADD) for the design of spoil piles, pre-strip dumps and spoil re-shaping. This approach has been applied to a number of mine sites with earthworks operations covering hundreds of hectares and hundreds of millions of cubic metres volume. We are continuing to provide that consultancy service and at the same time are involved in the development of more sophisticated software tools to apply to reclamation design.

Jan 1, 1991

By John H. Walsh

"ForewordPart I of this paper, published in the March 1992 issue of the CIM Bulletin, surveyed the probable consequences of a limitation on the emissions of carbon dioxide to the atmosphere for the steel industry. What might be termed the conventional responses to this restriction open to the industry were also surveyed in that section. This section, Part II of the paper, explores a new option - the possibility for the joint production of iron and liquid fuels useful for transportation purposes. In this case, it is shown that it is important to minimize the production of carbon dioxide during the reduction stage to maximize the proportion of the reductant carbon embodied in the fuel. It is also advantageous to conserve hydrogen in the reduction step. In essence, the same carbon fulfills two purposes: it serves as a reductant and fuel for ironmaking and then as a constituent of a liquid fuel. If recovered plastics could be used in ironmaking, the same carbon could serve three useful purposes in turn. The conditions and limitations for the joint use of carbon in such 'cascading' processes are explored below. ABSTRACTIt is becoming increasingly probable that emissions of carbon dioxide from the fossil fuels will have to be reduced to deal with the threat of global warming. This issue is likely to be resolved one way or the other in the period 1995 to 2000 which does not leave much time to develop responsive options. In the intervening period, the policy of the Government of Canada is to stabilize emissions of greenhouse gases at their 1990 level by 2000, by encouraging greater efficiency in the use of energy. Should further reductions prove necessary, economic instruments would probably be employed but these would not be applied before a comprehensive international agreement is reached.There are three main themes in this paper: it is assumed that measures to control carbon dioxide emissions will in fact be necessary by the turn of the century; that there will be a rising need for liquid fuels to supply the world's steadily growing fleet of motor vehicles for many years to come, and that the future niche for Canada's industry in such a carbon-constrained world will be the operation of the energy-intensive industries with efficiency and environmental sensitivity.The steel industry, as a large user of both coal and energy in other forms, would be significantly affected by a need to reduce carbon dioxide emissions. This paper first examines what might be called the conventional responses open to the industry in such a situation and then explores a new possibility for making better use of carbon by the co-production of iron and liquid fuels."

Jan 1, 1992

By K Whelan

The Land Access Branch of the Mines Division of the Northern Territory Department of Mines and Energy is responsible for Aboriginal Liaison and cross-cultural matters that affect the Department. In essence, it exists to provide a basis for communication between the Department, industry. Aboriginal organisations and Traditional Owners. The paper outlines the various ways in which this is accomplished including the preparation of detriment submissions for pending land claim hearings, the use of promotional material to support access to Aboriginal Land for NTGS Mapping Programs and field work, and advice/assistance on exploration and mining issues.

Jan 1, 1994

By D. J. Jr. McAdam

This paper presents stress-cycle graphs for five samples of monel metal and three high-strength aluminum alloys. These graphs are evidently curves with horizontal asymptote. The position of the horizontal asymptote can be determined with sufficient accuracy by extending the experiments to not more than 50,000,000 cycles. For some of the graphs, there is a slight downward slope between 50,000,000 and 100,000,000 cycles. The slope is so slight, however, that, extrapolation from 50,000,000 to 100,000,000 cycles gives the endurance limit with sufficient accuracy. Monel metal and duralumin are not exceptional among non-ferrous metals in endurance properties. IN Part I of this paper' a comparison was given of the results obtained in investigation of the endurance properties of non-ferrous metals in .three laboratories: the Engineering Experiment Station of the University of Illinois, the U. S. Air Service at McCook Field, Dayton, Ohio, and the U. S. Naval Engineering Experiment Station, Annapolis, Md. Part I was devoted to a discussion of the forms of the stress-cycle graphs obtained at the three laboratories. For comparison, typical graphs obtained at the three laboratories were plotted on the same semi-logarithmic scale. The typical rotating-cantilever graph for ferrous and non-ferrous metals obtained at the Naval Experiment Station was described as a curve descending with gradually decreasing slope to a horizontal line. In the reply to the discussion of Part I, however, this graph was described as a curve with horizontal asymptote. It. was also said that the ordinate of the asymptote (the endurance limit) could be determined by endurance tests of not more than 50,000,000 cycles. This description was intended to apply only within the range of ordinates used in plotting an ordinary endurance graph. It was recognized that if .extended upward beyond the usual field, the curvature of the graph would decrease until -the graph would either approach a straight a line or possibly reverse its curvature.

Jan 2, 1926

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By G. H. Hope, D. Green

"Recent process advances at Lac Minerals Est Malartic Division are discussed. The Est Malartic mill treats massive sulphide, copper/gold ore from the Bousquet 2 mine, to produce a gravity gold product, a copper flotation concentrate and a gold precipitate. The mill operation has been improved by the application of Knelson concentrators to replace jigs, the application of Outukumpu high grade tank cells and optimizing the cyanide leach to minimize cyanide consumption.IntroductionThe Est Malartic mill is located near the town of Malartic in the Abitibi Region of north western Quebec. The mill has been in production since the mid- J 930's processing mainly clean, free milling gold ore. Active mining from the Est Malartic mine ceased in 1980 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that modification of the Est Malartic mill to handle this new ore source was economically more attractive than building a new facility on site. Modifications to the mill to process the high copper/gold ore from the Bousquet 2 mine began in late 1989 and the new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leach circuit continued operating on the copper flotation tailings with some minor modifications to the solution handling systems. An SO,/air cyanide destruction circuit was also added at this time."

Jan 1, 1993