Search Documents

By John Sakala, Jeyapandian Sasikumar, Sydney Kwalela

The Isasmelt Furnace was commissioned in September 2006 with a concentrates treatment capacity of 850,000 tonnes per annum. However, the converter section became a bottleneck to the high throughput. Over 25% of the Isasmelt Furnace down time was attributed to lack of converter space. Factors that affected converter operations were low tuyere line campaign life (an average of 150 blows), high reverts generation, low conversion rates, and high converter cycle time. As a result of efforts carried out to improve converter operation, the average campaign life has increased to over 250 blows and reverts generation has been reduced from 22% of concentrate treated to 15%. Blister copper conversion rate has increased from 15 tonnes per hour to 19 tonnes per hour and blowing time per cycle has been reduced from 5.7 hours to 4.7 hours.

Jan 1, 2012

By V. K. Banakar

The occurrence of hydrogenous ferromanganese encrustations (Fe-Mn crusts) on the Cretaceous age Afanasiy-Nikitin Seamounts (ANS) in the eastern Equatorial Indian Ocean (EEIO) was first reported by Banakar et al. (1997, Marine Geology). The major element composition of the samples from the upper flank of the ANS (~1650 m water depth) indicated enrichment of Co up to 0.9 % (Parthiban and Banakar, 1999, Indian Mineralogist). Subsequently a project supported by the Department of Ocean Development to explore the ANS for Co-enriched Fe-Mn crusts was launched in 2002 by the National Institute of Oceanography. Sampling at regular depth intervals along two transects on the slopes of the northern elevated region of the ANS was carried out. The Fe-Mn oxide deposition is evident on almost all types of substrates viz., basalts, conglomerate limestone, fossil corals etc., and the thickness of the oxide layer varies from a patina to 7 cm. The Fe-Mn crust growth is evident only above a water depth of 3200 m, below which semi-lithified carbonate ooze is dominant. The ANS Fe-Mn crusts from all the water depths exhibit Mn/Fe < 1.5 suggesting pure hydrogenetic accumulation of metal-hydroxides. Bulk sample Ce-contents for a few selected depth-representative samples are remarkably high, up to 3700 ppm with an average of ~2500 ppm. The positive Ce-anomaly decreases from ~8 at 1600 m depth to ~1.6 at 3200 m depth, which is in contrast to the modern dissolved oxygen depth-profile in the region. This observation suggests that major time-period of the Fe-Mn crust accretion history is dominated by ambient waters with lower-oxygen at deeper depths than at the intermediate depths. This in turn probably suggests a major reorganization in the deep-intermediate hydrography of the region in the past.

Jan 1, 2005

By Richard L. Sanford

This report summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. References to computer applications throughout the mining industry are presented as well as comments on the availability of programs to interested organizations or individuals.

Jan 1, 1977

By LEANDRO RODRIGUES RAMOS

Os Sistemas de Nível 2 de Otimização da ArcelorMittal Tubarão impactam diretamente no processo produtivo (Qualidade, Produtividade, Produção), sendo que parte considerável destes sistemas são executados em plataforma legada de hardware (Alpha Digital). Em 2011/2012, o fim do ciclo de vida da Plataforma Alpha (Open VMS) anunciado pela HP trouxe este tópico para um lugar de destaque na matriz de risco da Engenharia de Automação. A principal estratégia é a migração para novas plataformas, porém associa-se a esta opção um custo e tempo elevado, principalmente se tratando de sistemas de alta complexidade e disponibilidade. A gestão de um estoque de sobressalentes também se torna cada vez mais difícil devido à escassez destes equipamentos no mercado global. Considerando estes fatores, a busca de soluções alternativas de curto prazo se fez necessária. Uma tecnologia de emulação e virtualização de plataforma foi validada e um projeto piloto implantado no sistema responsável pela otimização do processo de reaquecimento de placas do Laminador de Tiras a Quente. O uso desta tecnologia promoveu uma portabilidade direta do sistema para um hardware padrão de mercado (Intel x64), em curto prazo e sem impactos operacionais, podendo ser disseminada para outros sistemas, garantindo um pulmão para futuras migrações.

Jul 30, 2018

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a mini-computer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns an echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display discs, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 10, 1980

By Tiejun Chun, Gutian Mu, Jiaxin Li, Hongming Long, Zhengwei Yu, Ning Li

The basic characteristics of iron ore, including assimilation, fluidity, cohesive phase strength and the ability to produce calcium ferrite, are often used to evaluate the sintering properties of iron ore and guide the optimization of iron ore blending. Six kinds of common iron ore used in a steel company in China were selected in this work. The basic characteristics of the single iron ore and blended iron ores were studied, as well as the difference between weighted averages of basic characteristic index of single iron ores and the real value of basic characteristic index of blended iron ore under different ore blending ratios. The results shew that the liquid phase liquidity, cohesive phase strength and calcium ferrite formation ability had a significant linear positive correlation with SiO2 content. The weighted average of basic characteristic index of single iron ore cannot fully reflect the actual blended iron ore properties. The optimization of the blending ratio can be achieved through the detection of the basic characteristics of the mixed iron ore, combined with the basic characteristics of iron ores.

Mar 1, 2018

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.&apos; In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

By H. B. Pulsifer

This paper outlines a method for rapid production of flat,, granular surfaces on many of the medium hard alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesiurn which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have been used to good advantage for the purpose. However, if they are expected to etch rather deeply—that is, smooth as well as characterize— the results may be far from satisfactory. Advantages of Chromic Acid In a protracted series of experiments it has been found that the addit,ion of chromic acid may be of the most surprising benefit. The function

Jan 1, 1929

By H. B. Pulsifer

This paper outlines a method for rapid production of flat,, granular surfaces on many of the medium hard alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesiurn which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have been used to good advantage for the purpose. However, if they are expected to etch rather deeply—that is, smooth as well as characterize— the results may be far from satisfactory. Advantages of Chromic Acid In a protracted series of experiments it has been found that the addit,ion of chromic acid may be of the most surprising benefit. The function

Jan 1, 1929

All branches of our profession may look back &apos;with pride upon the patriotic service rendered by engineers during the war. That war has been won. The mortal danger which it threatened has been averted. But the effects of the torture inflicted by it still remain, a fever in the blood of the body politic. Fever begets delirium and, unless its course be checked, has a tendency to produce convulsions. The only safe course is to take immediate steps to allay the fever. The seat of the present trouble is industrialism; as production is at the foundation of civilization, a diseased condition there carries pain and consequent unrest into every member of the organism. Who shall supply the cure? Quack doctors, nostrums in hand, rush forward from all directions promising to perform miracles. But sane men know that no miracles, though invoked by star gazers of purest intention, will prevent or accelerate the orderly operations of the laws of nature and of human life. Delirium must be controlled by the firm, gentle hand of intelligent, sympathetic authority. Fever must be allayed first by removal of all poisons from the system, then by consistent ministration of cooling, quieting restoratives, then by simple, wholesome nourishment. Nature will, under such treatment, supply the permanent cure.

Jan 12, 1919

By G. H. Alvey, A. W. Foster

The measure of value of an oil property is approximated by the length of time it takes to "pay out;" viz., the time required for it to return the original investment. This time varies in different fields. In the Appalachian and Mid-Continent fields, a good investment pays out in about four years; in California, it requires a slightly longer time; and in the Gulf field about two years. The two principal methods for establishing these values are based on acreage, as in California, and on production, as in the Appalachian field. The method of establishing values based on production1 was worked out in the Appalachian fields and approximates the value remarkably well in some fields; but it is a rule of thumb and should be used intelligently. Briefly, the method is as follows: An arbitrary number of dollars (called the barrel-day price) multiplied by the number of barrels of settled daily production of the property gives the value. In its crudest application, the barrel-day price is determined by the "$10 to $0.01" rule, which means that the barrel-day price is one thousand times the prevailing price of oil. For instance, with oil at $3.50 per bbl. the barrel-day price would be $3500 per bbl. This rule, however, is not strictly applied, for the barrel price is varied according to whether or not the wells "hold up." But when a barrel price for a district has been fixed it is quite general to raise or lower the price with the fluctuation in the price of oil; here the"$10 to $0.0l"ruleisused extensively. However, the prospective purchaser takes into account tangible equipment upon the property, the extent to which the drilling program has been carried out, whether or not the wells are "shot" or natural, depth of wells, spacing of wells, paraffin trouble, etc. The basis of this method is settled production. As soon as production is considered settled, a flat barrel-day price is generally applied to all properties, no matter what their age. If it were possible to show that this flat rate was erroneous and that the value of the property depended on the point on the decline curve at which the wells happened to be (in other words, their age), and also on the operating costs, the future price

Jan 1, 1921

By Wes Bender

Considering the current interest in Global Positioning System (GPS) usage, it might be timely to look at a more efficient means of utilizing these instruments. The GPS system currently utilizes 28 satellites (4 are spares) circling the earth in an inclined orbit. Normally at least six satellites are within your area of reception at any given time. The satellites broadcast an extremely accurate time signal and an almanac containing all the satellites’ orbital data. This information is updated regularly as the satellites circle the earth. Your GPS receiver, once it has picked up one satellite’s broadcast, can then determine which other satellites should be available for plotting.

Jan 1, 2002

By J. Shibata

The recovery process of valuable metals, such as Ll, Mn, Ni and Cr from a waste lithium battery was developed n this study. Lithium and Mn are selectively leached from the battery by using dilute mineral acid. Main part of the battery comprises stainless steel, and Fe, Ni and Cr are easily leached by the mixture of dilute HCl and HNO3 Lithium and Mn are precipitated as metal carbonates from the? individual leached solution with sodium carbonate solution. The solution containing Fe,Ni and Cr Is treated by solvent extraction to separate NI and Cr from the leached solution. The experiments are carried out for leaching and separation steps. According to the experimental results, the flow. sheet for a recovery process of valuable metals from a waste lithium battery has been established.

Jan 1, 1995

By I. S. Laitinen

Outokumpu Technology has recently introduced new technology in both copper electrorefining and electrowinning. This technology includes, among other things, a new permanent cathode (Outokumpu Permanent Cathode) and new busbar technology (Outokumpu Double Contact System). The new technology has already been tested in commercial scale cells. To get a better understanding of the busbar system a multiphysical simulation model of the electrowinning and electrorefining cells was developed. A mathematical model of electrical conduction and heat transfer in a copper electrolysis cell was developed from partial differential equations. The model was expanded to a cell group including seven electrolysis cells connected electrically in series. The model was solved numerically using the finite element method (FEM). Using the model, different intercell busbar systems were simulated. Typical electrical disturbances, like loose contacts between cathodes and the main busbar and short circuits between electrodes, were included in the simulation. The results of the simulation runs with conclusions are presented in this paper.

Jan 1, 2007

By E. L. Swarts

In the course of a program on high-temperature processing and electrowinning of uranium at the Knolls Atomic Power Laboratory,&apos;&apos; it became necessary to give attention to the interaction of molten uranium with graphite. Although it is known3 that a protective interface layer may form, details of this reaction have not been reported. Unfortunately it was impossible to complete the planned experimental program. However, the general problem is considered of sufficient interest to warrant reporting those preliminary results actually obtained. EXPERIMENTAL PROCEDURE Interface carbide layers were formed by melting samples of cleaned uranium metal in small closed graphite crucibles. Equilibrations were conducted in vacuo or in an atmosphere of dry helium at temperatures ranging from 1150" to 1400°C and for periods of from 24 to 240 hr.

Jan 1, 1960

By B. McLaughlin

Agnico-Eagle started sinking the Penna Shaft in 1995 with a hoisting plant capable of hoisting 1800 t/d from a 2240 m deep shaft. Exploration success led to the installation of a hoisting plant capable of extracting 4500 t of ore and 1800 t of waste per day from a depth of 2210 m. The introduction of a new rope selection factor, permitting a safety factor of 4.0, represented the breakthrough required for a cost-effective project. This paper describes the process taken to introduce the new rope selection factor and its impact on the original plant.

Jan 1, 2004

Iron deposits of every major type except laterite occur in Quebec, and form one of the major iron ore resources of the world. The five principal types of ore described are: (1) hematite-goethite masses derived from iron formation through the oxidation and enrichment of iron by natural processes; (2) taconites consisting of fine-grained iron formation; (3) metataconites composed of coarse-grained iron formation; (4) iron and titanium oxide minerals in massive or disseminateed deposits within gabbro and anorthositic rocks; and (5) replacement or contact? metasomatic magnetite deposits associated with complex silicate and skarn mineral assemblages. Most of the ore, although relatively low grade, is easy to concentrate. The physical properties of the ores that affect the choice and efficiency of beneficiation methods are described. The extent to which iron ore from this area can be utilized in the future will depend on the continued use and improvement of highly efficient methods of beneficiation.

Jan 1, 1964

By S. H. Gelles

Samples of poly crystalline zinc of 99.999+ pct purity were observed metallographically after having been exposed to hydrostatic pressures of up to 27 kbars. The deforrnation produced by this treatment was analyzed using X-ray and metallogaphic techniques. Basal-plane slip occurred universally in all grains exumined at the lowest pressure used (8 kbars). At pressures of >23 kbars, {1012} twin nucleation and growth were noted as well as slip. Formation of bend planes, complex kink bands, and recrystallization at the gain boundaries were also observed in this pressure range. These observations are discussed in reference to the expected deformation behavior of zinc under high hydrostatic pressure. It has been shown over the past few years1&apos;3 that anisotropic, poly crystalline metals can be made to deform plastically by the application of a hydrostatic pressure. The effect is greater 1) the larger the anisotropy of linear compressibility and 2) the smaller the stress level needed to produce plastic deformation. Zinc having both very anisotropic linear compressibilities and a very low critical resolved shear stress (CRSS) for basal-plane slip has been shown to exhibit large amounts of plastic deformation when subjected to a hydrostatic pressure.2,3 At pressures up to 15 kbars, grain boundary migration and slip on one set of glide planes have been reported.&apos; After exposing samples to 20 kbars pressure, grain boundary migration, single slip, multiple slip, and twinning have been noted.&apos; The identification of the deformation modes operative under these conditions has not been reported. It was the purpose of this research to identify the deformation modes induced in poly crystal line zinc by the action of a hydrostatic stress and to study the strain accommodation at grain boundaries. Hydrostatic pressure could affect the operational modes of deformation by altering the Peierls-Nabarro stress. This may be roughly approximated by the relationship4

Jan 1, 1967

By Tony van der Steen

Subsea mining system are designed for the following, principally different, tasks: Dreding - The destruction and removal of seabed sediments overlaying the bedrock. Cleaning - The competence of the system to systematically remove the deposits from an undulating hard bedrock with irregular pulleys, channels and fissures. Factors that influence the choice of dredging equipment for a specific project are project requirements such as environmental conditions, location and water depth. However, the most important selection criteria are soil conditions. As a consequence, possible dredging systems, must be evaluated for the following, principally different, characteristics: Dredging proficiency - The destruction of the strata by the equipment. System stability - The capability of the soil to support the subsea equipment The above parameters are determined by the strength characteristics and the bearing capacitv_ of the soil. The author describes the processes involved in excavating the subsea deposits and (transporting the gathered soil as a water-soil mixture to the surface using different excavation and transport methods.

Jan 1, 1998

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000