Search Documents

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By C. M. Wayman, R. Bullough

The selection rules fir twinning in fcc, bcc, and hcp lattices as established in Part I are used to predict the positions, relative to the matrix (untwinned) reciprocal lattice, of reflections due to double diffraction from the twins. These doubly diffracted reciprocal lattice points, which often coincide with ordinary matrix reciprocal lattice points, are deduced from kinematical considerations. 1. INTRODUCTION. A Bragg diffracted beam under certain conditions may be rediffracted to produce a third beam i .e., the incident beam, the first diffracted beam, and the rediffracted beam). In such a case an initial incident beam is diffracted by a set of planes; the diffracted beam may then be rediffracted by a second set of crystallographically different planes. The initially diffracted beam acts as an incident beam for the second set of planes, thus resulting in a twice-diffracted beam. This twice-diffracted beam may be regarded as a singly diffracted beam from a set of lattice planes whose structure factor is zero. In order to find the reciprocal lattice point corresponding to the doubly diffracted beam, it is customary1,2 to combine vectorially the component reciprocal lattice vectors which head to the extra reflections. For example, hcp metals may exhibit the forbidden (0001) reflections.* As Fig. 1 shows, the (0001) reciprocal lattice point results from: (1010) + (1011) = (0001) Similarly, combination of the beams (1011) and (1010) gives rise to: (1011)- (1010) = (0001) As Pashley and stowell2 have pointed out, even if in fact the double diffraction points lie on the Ewald sphere, they may not actually represent observed doubly diffracted beams because the initially diffracted primary beam, i.e., the source, must also correspond to a reciprocal lattice point which lies on the sphere of reflection; however, the reciprocal lattice point corresponding to the planes causing the rediffraction need not lie on the sphere. A little consideration of the Ewald construction in Fig. 2 makes this argument clear. In Fig. 2 the incident beam is represented by the wave vector ko. This beam is initially diffracted by the lattice planes (hkl) which are represented by the reciprocal lattice vector r(hk1) The reciprocal lattice point (hkl) of course lies on the Ewald sphere in order that the Bragg condition be satisfied. The initially diffracted beam is represented by the wave vector kl. If now kl is rediffracted by a second set of planes (h'k'l') resulting in k2 the lattice point (h"k"l") must lie on the Ewald sphere if the double diffracted beam k2 is to be observed. It is clear that (h"k"l") is the vector sum of (hkl) and (h'k'l'), and that (h'k'l') need not in fact lie on the Ewald sphere. In the usual1,2 analysis the origin (000) of the reciprocal lattice is shifted to the point (hkl). However the translation (000)— (hkl) automatically shifts the point (h'k'l') to the Ewald sphere, i.e., (h'k'l')— (h"k"1"). It is to be seen that (hkl), the source reflection, must lie on the Ewald sphere; if it does not the translation (000) — (hkl) places the "new" origin off the sphere, not satisfying the Ewald construction and hence the Bragg condition. The point (h"k"1") of course must lie on the sphere if it corresponds to an observed doubly diffracted beam. It is to be noted that crystals having the hcp structure, as just discussed, are intrinsically capable (i.e., without lattice defects such as twins) of double diffraction, as contrasted to fcc and bcc crystals which are extrinsically capable (requiring lattice defects or reoriented lattice regions). The "allowed" bcc reciprocal lattice points (which comprise an fcc lattice) are (110), (2001, (211), (220), (310), (2221, (321), (4001, and so forth. The combination

Jan 1, 1967

By Paul A. Pierce

In 1984, the Bureau of Mines evaluated an area previously identified as having "probable mineral resource potential" for copper, lead, zinc, gold, or silver within the Elkhorn Wilderness, about 5 miles west of Winston, MT. The purpose of this study was to determine whether the mineralized structures at nearby mines and prospects outside of the Wilderness extend into and contribute to the anomalous zone and, if so, to expand the domestic supply of strategic and critical mineral resources for future needs by identifying and quantifying resources on public lands. Fifty-eight soil samples, 23 rock samples, and 1 stream sediment sample were collected in the Staubach Creek area. Overall sample analyses suggest the anomalous zone in the Staubach Creek drainage is possibly associated with -.mall pyritiferous quartz veins. These veins or veinlets may be part of a system of northeasterly-trending structures prevalent in this art of the Wilderness. However, there is not sufficient evidence to prove that identified resources outside of the Wilderness extend into it in the Staubach Creek drainage, or that economic base- or precious-metal deposits are likely.

Jan 1, 1987

By N. C. Gay, P. J. Van Der Veever

The Klerksdorp gold mining district, South Africa, experiences a relatively high level of seismicity with many seismic events of magnitude greater than 4. These large events appear to have foci close to fault planes, most of which displace the strata by several hundred metres over a wide area. To help understand the mechanism of these large mining- associated seismic events, in situ stress measurements were made at 4 sites using "CSIR doorstopper" strain relief techniques. The sites were chosen close to, or some distance from fault planes and other structures. The results show that at all 4 sites a relatively large horizontal stress is oriented approximately north- west. The magnitude of this stress ranges from 0,78-1,O of the vertical stress. A marked horizontal stress anisotropy, varying from 13-30 MPa is also present. The dominant structural features are large, north-east striking normal faults which extend across the entire length of the goldfield. Displacements across these faults vary from a few centimetres to several hundred metres. Bedding plane faults across which large displacements may occur are also common as are north and north-west striking dykes. The majority of the faults strike at approximately 90º to the maximum horizontal stress and at all sites a large compressive stress plunges in the direction of dip of the strata and fault planes. Thus a significant shear stress may act across suitably oriented planes causing them to be in a state of potentially unstable equilibrium. This abnormal stress situation would exist along the entire length of the fault

Jan 1, 1982

By Howard N. Eavenson

WHEN the A.I.M.E. was formed 75 years ago the bituminous coal industry was in its swaddling clothes, although it had been operating for more than a century and coal was being mined in every state now producing it, and its output had long passed that of anthracite. In 18/1, the value of bituminous coal was about seventy per cent of the value of all metals produced and more than one fifth of the value of all products of mines, both metallic and nonmetallic.[1a] While many of the operating mines then shipped by rail, most of the development was along waterways, although the canal era of transportation was nearly at its end. Coal mining is a heavy industry and one of the best measures of its progress is its output throughout the period. Fig. 1 shows this graphically from 1800 to 1945. From 1870 to 1910, the production-which is very nearly the consumption-almost doubled every decade, a most amazing growth. In 1918, in World War I, a peak was reached and a decline began, which ended in 1932. A gradual recovery then started, interrupted in 1938 but culminating in the record output of 1944, when, owing to World War II, a tonnage of 619,576,000 was produced. It is evident that the forces leading to the continuous increase ending in 1918 have spent themselves and that only unusual conditions will require so large a production again. The postwar conditions of World War II will probably

Jan 1, 1947

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

By J. W. Whitlow, P. K. Theobald, W. C. Overstreet

Monazite placers in a region of the Carolinas ex- in 1951-1954 by the USGS are estimated to contain at least 53,000 short tons of thorium and 4600 short tons of uranium. None of these deposits is being mined. The 5200-sq mile area investigated extends northeast along the western Piedmont from the Savannah River in South Carolina to the Catawba River in North Carolina. Much of the region is 700 to 1100 ft above sea level. Gentle hills and broad interfluves give a local relief of 100 to 200 ft. This increases to 1700 ft at the west margin of the area where the east flank of the Blue Ridge is approached in South Carolina and the South Mts. are entered in North Carolina. This report is restricted to placers in the Piedmont. Monazite deposits in the Blue Ridge and coastal plain were not covered by the investigation. Monazite Mining in the Carolina Piedmont: Discovered in 1879 by W. E. Hidden,' the monazite placers in the Carolina Piedmont were first mined in 1886. The area was a major world source for thorium and the lanthanides until 1895, when Brazilian monazite entered the trade. Total output from the Carolina Piedmont has been nearly 5500 tons of monazite,2 but the placers have been idle since 1911, except for 48 tons produced between 1915 and 1917. Monazite mining was revived in the Carolinas in 1954 when a dredge operated by the Heavy Minerals CO. opened a fluviatile placer along Horse Creek in the coastal plain near Aiken, S. C. Geology and Mineralogy: Two recent papers",' have described the geology of the monazite placer district in the Piedmont between the Savannah and Catawba rivers; the general geology of the region has been reviewed by P. B. King.' These reports show that the placers are in locally derived alluvial sediments that cover the floors of shallow, narrow valleys in an area underlain by monazite-

Jan 1, 1960

By A Frostick

Ranger uranium mine is surrounded by the World Heritage listed Kakadu National Park and offsite impacts resulting from mining at Ranger would affect the Magela Creek catchment first. Radionuclides, lead isotope ratios and metal concentrations were measured in sediment cores from the Magela Creek catchment around Ranger to investigate the dispersion of mine-derived particulates. The study found a localised area within the Ranger mineral lease, where upper sediments had elevated levels of radionuclides and trace metals and radiogenic Pb isotope ratios. There is no current evidence of sediment dispersion from Ranger further downstream within the Magela Creek catchment.

Aug 1, 2010

By J. D. Sargent

Selenium might be described as a paradoxical element, being a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden.

Jan 1, 1954

By John W. Adams

The present status of the National Bureau of Standards program is that many magnetic tapes of analog data have been recorded in four major mines. Each mine uses different types of equipment. In addition, some surface measurements of noise have been made at two additional mines. Two types of recordings have been made: (1) broadband measurements for spectral plots and (2) narrowband measurements for amplitude probability density (APD) plots. Only data from one mine (Robena #4) has been processed and was, presented at this workshop. The short-term goals are: (1) finish processing data from the other mines, (2) establish or reduce measurement system uncertainties, (3) put Robella report into final form for distribution, and (4) hold a review to determine what has been done, to distribute and to interpret the preliminary data, and to determine what still needs to be done. Long-term goals are: (1) complete final reports on each of the mine trips, (2) establish techniques for predicting noise in mines already visited and establish uncertainty bounds for these predictions, and (3) establish techniques for predicting noise in mines that have not been visited (but that use similar equipment to those visited) and also establish uncertainty bounds for these predictions. Specific factors or formats to be presented include: (A) For underground broadband measurements: 1. 300 Hz to 100 kHz spectral plots 2. 300 Hz to 384 kHz spectral plots 3. 300 Hz to 192 kHz spectral plots 4. 300 Hz to 6kHz (subject to change to 3 or 12 kHz) spectral plots (B) For surface broadband measurements: 1. 300 Hz to 6 kHz (or 12 kHz) spectral plots 2. 300 Hz to 3 kHz spectral plots (C) For underground narrowband measurements : 1. APD plots at 12 frequencies from 10 kHz to 32 mHz of magnetic field strength 2. R. M.S. and average values will be calculated based on time averaging for these plots (D) Sample spectral measurements of: 1. Roof-bolt voltages 2. Trolley wire-to-rail voltages 3. Phone line currents

Jan 1, 1973

By M. A. Rabah, F. E. Farghaly, M. A. Motaleb

"Wastewater from industrial galvanization industry was reclaimed under current flow stream conditions. Results showed that the raw water contains 0.7 % by weight total suspended solids (TSS) causing turbidity amounting to 30. Measurements of Zeta potential as a function of pH revealed that solid separation takes place at pH 9. Addition of H2O2 to the polmer solution helps to oxdize ions of iron and zinc metals toinsoluble ferric oxide and zinc hydroxide to a higher state of oxidation. Addition of 5 mg/L of cationic magna flocculants polymeric solution helps the rapid separation of the turbidity. Separation of floccules so formed takes place by filtration. Addition of peroxide ions to the turbid wastewater confirms the physical stability of the flocs so formed. Impurity flocculation takes place in few seconds. Maximum temperature for safe solid removal was <30°C. The treated water was pure and safe for recycling or use in domestic purposes.IntroductionStocks and et. al. [1] show that the galvanizing process introduces spent pickling acid waste production, but its major constituent, could be used. Survey of the operational procedures adopted and the acid wastes produced by UK Galvanizers are reported. Various methods to recovery spent acid of suitable composition and to eliminate zinc contamination was considered. Application of the Kleingarn acid management system reduces waste volume, saves hydrochloric acid (HCl) and increases component throughput whilst, in conjunction with zinc elimination, could allow recycling of the majority of galvanizer’s acid wastes.Dahab [2]; Kerney [3] reported recycling of galvanizing products, including pickleliquor. Kerney suggested a mobile treatment plant for recycling pickling acids. Dahab found that pollution reduction could be achieved by relatively simple operational changes to the process that gave fairly short payback times.Rozenblat and et. al.[4] studied the extraction of zinc (II), iron(III) and iron(II) with Tributyl phosphate (TBP) from hydrochloric acid solutions containing high zinc(II) concentration. Two technological approaches for the separation are considered. Firstly, the selective extraction of iron(III) (iron(II) is oxidized to iron(III)) over zinc(II) with TBP deficiency. Secondly, iron(III) reduction to iron(II) followed by zinc(II) selective extraction with an excess of TBP. Prior stripping, the organic phase was washed with small amounts of water. Scrubbing of TBP solutions containing iron(III) contaminated with zinc(II) gives always a mixture of zinc(II) and iron(III) which must be recycled to the extraction step in continuous process. The following technological concept is proposed: reduction of iron(III) to iron(II), extraction of zinc(II) with 5-10 volume excess of TBP, washing of TBP phase contaminated with iron(II) with small volumes of water and recycling of the scrubbings and stripping of zinc with water."

Jan 1, 2008

By Ted C. Briggs

A special high-pressure Burnett-type compressibility apparatus was constructed and used to determine compressibility factors for pure helium, pure nitrogen, and nine helium-nitrogen mixtures containing 89.47, 79.04, 69.69, 60.09, 49.24, 41.02, 30.99, 20.53, and 10.67 mole-percent helium. A total of 161 runs were made consisting of 2,355 observed pressures. Data were obtained at 0°, 25°, and 50° C and at pressures to 1,000 atmospheres. A power series in the reciprocal volume, commonly called a Leiden series, is used to represent the compressibility factors. Three parameters in the series are required to represent helium, five parameters to represent nitrogen, and from three to five parameters to represent the mixtures. Compressibility factors are believed to be accurate to better than 0.1 percent over the entire pressure, temperature, and composition range.

Jan 1, 1972

By Jey K. Jeyapalan

A characteristic common to most tailings dam failures caused by earthquakes or excessive rain storm is that the tailings tend to liquefy and flow for substantial distances as a viscous fluid, with the potential for extensive damage to property and life. Failures of El Cobre, Chile (1965), Mochikoshi, Japan (1978), Aberfan, Wales (19661, Buffalo Creek, West Virginia (1972) are examples of such catastrophic incidents. In these four incidents more than 400 lives were lost, and the loss of property was approximately $200 million. In order to be able to assess the potential for damage in case of such a failure, it is necessary to predict the possible extent of flow slide movement. This paper discusses simple procedures for performing such analyses. Also, in order to illustrate the use of these analysis procedures in tailings dam design, two case histories are analyzed.

Jan 1, 1982

By L. John Minnick

A revised and expanded edition of a previous paper** dealing with reactions of calcium and magnesium oxides and hydroxides with pulverized coal fly ash is presented. Lime-fly ash specimens were cured at constant temperature and subjected to X-ray diffractometry, differential thermal analysis, pozzolanic reactivity tests, and microscopical investigations. Bars of limefly ash were subjected to cycles of wetting and drying, and measurements of length change were recorded. A discussion of variations within and among types of lime and types of fly ash is presented. The nature of the pozzolanic reaction is reviewed, particularly as related to compounds which are used up and formed during the aging process. The relationship between the pozzolanic reaction and the resultant physical properties of the mixtures is examined.

Jan 1, 1968

A review of the most widely used global extraction sequences in sublevel is undertaken. The review includes techniques used to extract massive as well as single or multiple steeply dipping tabular orebodies. The paper also deals with thick flat lying orebodies suitable for open stoping. Techniques used to minimise the effect of stress redistributions on a global scale are discussed for all the extraction sequences analysed.

Jan 1, 2003

By B. Steyn

AngloGold Ashanti?s Obuasi Mine, in Ashanti Province, Ghana, operates a plant utilizing bacterial oxidation technology. The mineralization consists predominately of arsenopyrite with gold associated in the sulphides. The plant was commissioned in 1994, at that time was the largest BIOX® plant in the world, and has been operated by AngloGold Ashanti since 2004. The constraints identified in the plantwere the flotation capacity, BIOX® feed size and disruptions to the BIOX® process. This paper focuses on the practical steps that were followed in order to increase the recovery of the plant. The original plant design was based on a head grade of 10 g/t and an overall recovery of 86.5%. In 2007 the plant was operating at an overall recovery of 79.2% at a head grade of 5.6 g/t and this has improved to 80.6% at a head grade of 5.8 g/t during the last quarter of 2008. Additional improvement to 81.5% are expected by the end of April 2009. Improvements that have been implemented include: ?Replacement of the regrind mill ?Installation of additional float capacity ?Installation of a scavenging circuit ?Installation of a complete water treatment plant. In addition we have focused on the effect of the water circuit on the BIOX® process and the steps involved in correcting this problem. The water circuit was originally designed as an open circuit and through environmental considerations the circuit was closed towards the end of 2007. The bacteria in the BIOX® are particularly sensitive to cyanide and cannot tolerate levels above 0.05ppm (free cyanide), this required extensive modifications to the water circuit. The plant improvement project is ongoing and the current scope of work should be complete by the end of April 2009. Further research and development work is being planned, which includes a ?white rot bacteria? that can consume the preg-robbing carbon and oxidize the sulphide in a single pass.

Jan 1, 2009

By H. Q. Golder

With the development of open-pit mines of ever increasing depth, the stability of the pit slopes in soil and rock is of growing economic importance. How is it, considering the newness of the problem that we know anything at all about the stability of man-made slopes? How much do we know and how did it all begin? We can make a reasonable estimate of the stability of a slope in soil, but we know as yet woefully little about slopes in rock because the problem is much more complex. It is only with the development of the capacity of the computer to handle wearisome calculations that any but the simplest of stability problems in rock have become possible of solution. But what we do know is a guide of immense value in the design of slopes in rock. But remember that the computer is a great elevator; it takes everyone&apos;s feet off the ground! So our study began with soils and what is now known as "Soil Mechanics", which is a translation of the German term "Bodenmechanik". It is a pity that the title of Terzaghi&apos;s book "Erdbaumechanik" was not used instead. But here the task of the translator is difficult because English lacks the facility of German to string together several words and make a new one whose meaning is unequivocal. Thus, we have the three German words &apos;Erde&apos; &apos;Bau&apos; and &apos;Mechanik&apos;. &apos;Erde&apos; means "earth" in almost all the English senses including "soil". &apos;Bau&apos; and &apos;bauen&apos; convey the meaning of building and construction, and &apos;Mechanik&apos; means "mechanics" which includes statics and dynamics and the &apos;mechanics of materials&apos;, etc. So that a correct translation of the German is a phrase like "the mechanics of construction with, in or on, earth or soil." However we are stuck with &apos;Soil Mechanics&apos; and that is where it all began. Now this study or subject did not begin with &apos;Terzaghi&apos; although his contribution to the subject is unquestionably greater than that of any other single person. Every scientific discipline has its &apos;classical problem&apos; and that of soil mechanics is &apos;the earth pressure problem&apos; and it began in the 17th century. In fact, it probably began before this with the introduction of gunpowder to Western Europe in about the 15th century, but the first known reference to the problem was by Vauban, a distinguished French military engineer who lived from 1633 to 1707 and who gave rules for the dimensions of retaining walls from 6 to 80 ft. in height. The soil properties were not mentioned by Vauban probably because the rules were intended to be applied to fortifications only, but Poncelet (1840) claimed that Vauban&apos;s rules were based on a theory, and not simply on military and practical

Jan 1, 1972

By Simona Markic

With the aim of environment protection the program package HOMOGEN is used for realizing the planning and noxious components control in the coal produced. Using the program package PRIPREMA the division in levels and transformation (Hermite polynoms) in the N (0,1) distribution are made. By separated kriging 50 m x 50 m blocks are estimated on the levels and detailed distributions of the estimated component content are obtained. The face - longwall face is built in the blocks estimated in this way, and the direction of mining is determined. Using the stochastic simulation the distribution of the estimated production component (e.g. sulfur) on the face is obtained. Simulating the production of all faces in operation the distribution of the estimated daily mine production component is obtained. The estimated depot component is obtained in the same way. This procedure is used in the short-term planning of the estimated component movement for a given period in advance, and also in the daily production control in the case of changing conditions, e.g. the increased atmospheric pressure. The technology is successfully applied to the Velenje Lignite Mine Slovenia.

Jan 1, 1992

By David B. Reger

Widespread wildcatting for new supplies of natural gas and the beginning of importation from the southwest characterized the petroleum industry of West Virginia during 1944. Within the state, drilling for oil did not increase but. more gas wells were completed than in any previous year since 1937. Out of 40 wildcats drilled there were 25 gas discoveries and 15 dry holes. No commercial oil was found in the 40 wells. The proved limits of several oil pools were slightly extended by marginal drilling, resulting in 1300 acres of new oil territory, although no distinctly new pools were found. At least four new gas pools were assuredly discovered and various successful wildcats indicate future pools or wide extensions. The new proved gas territory, in definite new pools and definite extensions, is about 34,000 acres. A considerable net decline of proved oil has occarred and probably a slight decline of proved gas reserves. The account of operations, as gathered from trade journals and other reporting services, shows that 918 new wells were drilled, resulting in 71 oil wells with 613 bbl. of daily new production; 577 gas wells with 305,372,000 cu. ft. of daily open flow, and 142 dry holes. Also, 107 old wells were drilled to deeper sands, with 22 bbl. and 12,327,000 cu. ft. of added production. On the new wells the oil average was 8.6 bbl. per well per day, and the gas average was 529,241 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 15.47 per cent. On deeper drilling the ratio of failures was 19.63 per cent. Production of oil for the year was estimated by the Oil Weekly as 3,069,000 bbl., as compared with 3,349,000 bbl. in 1943. Production of natural gas for the year is estimated by the author as 200,000, 000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 223,789,000,000 cu. ft.t in 1943.

Jan 1, 1945

By Jerome Alexander

The object of this paper is to show that many of the important phenomena of metals and alloys are due to the facts that, at some stage, metals and alloys, or some of their constituents, are in a colloidal state and that a portion of the metal or alloy tends to remain in this state. The so-called amorphous phase in pure metals is an isocolloid, consisting of colloidal groups of metal molecules that may be dispersed in still more finely subdivided metal; these colloidal particles are not truly amorphous, but may consist, in part, if not entirely, of ultramicroscopic crystals; as a result the expressions amorphous phase and amorphous theory might he replaced by the expressions colloidal phase and colloidal theory. Any substance is in the colloidal state when the constituent particles consist of molecular or atomic groups, whose size varies approximately from about 100 down to about 5pp, that is from just below the limit of microscopic resolvability to the dimensions commonly ascribed to the larger molecules. Colloidality involves no assumption as to the shape, internal structure, or orientation of the colloidal particles; size alone is the critical factor. A colloidal system may therefore contain crystalline groups, or amorphous groups (non-crystalline, random or haphazard clusters), or a mixture of the two. All colloids consist of at least two phases, the subdivided substance, or dispersed phase, and the substance into which this is subdivided, the dispersion medium. It is not necessary that there be any chemical difference between the dispersed phase and the dispersion medium. As molecular forces are extremely powerful, their application may produce marked changes in the physical properties of metals. It is doubtful whether metal in the interior, especially of large masses, possesses the same properties as that on or near the surface, which alone is open to inspection.

Jan 1, 1921