Search Documents

By S. Moodley

In the chloride process for TiO2 pigment production, various titania feedstocks (i.e. rutile, synthetic rutile, slag, and upgraded titania slag (UGS)) are chlorinated in a fluidized bed reactor with petroleum coke at temperatures between 1000°C and 1100ºC to yield gaseous metal chlorides. Although feedstock preference is largely based on TiO2 content, feedstock physical properties (i.e. density, sphericity, size distribution, and porosity) differ; these differences will affect fluidization behaviour and can inadvertently affect conversion efficiency. For example, a high carryover from the reactor reduces particle residence time and decreases conversion rates. Owing to dwindling rutile reserves in the world, most chloride producers are forced to feed blends of feedstocks to their chlorinators; and so it becomes important to understand whether blends have an effect on the hydrodynamic properties of the bed. This paper describes the physical characterization of different feeds and the determination of the elutriation constants for slag, rutile, synthetic rutile, and a blend (i.e. 50 wt% rutile, 50 wt% slag).A common feature of the tests was that particles finer than 75 µm tended more than any other size to be elutriated. The tested rutile, classified as a Geldart Group B material, had the lowest carryover, whereas the slags had the highest. Interestingly, the elutriation constant ([ki]) of the blend is lower than those of either of its individual components.

Jan 1, 2012

By Wang Yingmin, Xu Zhuyun

There are 3 steps in the process of forming a mine ventilation system, (1) selecting a reasonable ventilation pattern (included pit shaft arrangement); (2) optimizing of the ventilation network and (3) computing and outputting the flow splitting results of the network with the optimal ventilating equipments selected. In the past, the first step was relied on artificial decision-making. In order to design a common ventilation system, some ventilation experts were needed to participate or do some examinations. Even so, the design made was reasonable only for those experts. If there is a mistake in the first step, then even the followed 2 steps are best done, the losses are very difficult to retrieve. So that, the first step is very important. The development of expert systems provided an efficient means and tool for all engineering fields. This paper presents an expert system of selecting mine ventilation pattern and pit shaft arrangement. After testing many times, it is shown that the system can perform the first step of designing a mine ventilation system, and can help the experts doing their study works more efficiently.

Jan 1, 1991

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

New Zealand contract mining has been well established for close to 50 years. The opencast industry has grown from mining quantities of less than 1 million bcm per year in the 1950s to around 20 million bcm in the late 1990s. Trends here are following those in other countries with mining companies looking to contract out more of the so called traditional mining work. The key driver behind this trend is not unique to the mining industry, but is simply a matter of concentrating on doing a few things well. In the case of the mining company this has come to mean owning and developing orebodies and where appropriate, marketing mining products, and leaving owning and operating of mining fleets to the contractor. This has the effect of reducing risk to the mining company as well as lowering costs. Both can be achieved without losing control of the key elements of the operation. Optimising performance is simply a matter of identifying the key drivers behind performance, having the right plant and the right people at the right place and providing these people with the information they need to manage the operation.

Jan 1, 1997

Jan 1, 1970

By K. J. Reid, I. Iwasaki, T. Sabelin

Introduction Occurrences of platinum group minerals (PGM) in mafic and ultramafic rocks in association with Cu-Ni mineralization are well known. Yet for the Duluth Complex, a large body of dominantly mafic igneous rocks in northeastern Minnesota with significant Cu-Ni mineralization (Bonnichsen, 1972; Boucher, 1975; Watowich, 1978; Weiblen and Morey, 1980), little has been published concerning its platinum group element (PGE) contents and mineralogy. In a previous study of massive sulfide rock, sperrylite (PtAs2) was found in nickel arsenide and recovery of arsenide minerals by flotation has been investigated (Iwasaki et al., 1986; Ryan and Weiblen, 1984). Recently, an announcement was made of the discovery of significant quantities of platinum and palladium [peak assay values of 9 g/t (0.27 oz per st)] in an interval of a drill core with disseminated sulfide mineralization 16 km (10 miles) southeast of Ely, MN (Anon, 1985; Sabelin, 1985). This paper describes PGM from the Pt-Pd-enriched zone and evaluates their potential for concentration. Geologic setting The Pt-Pd zone occurs in the South Kawishiwi in¬trusion near its basal contact at 734 to 737 m (2408 to 2418 ft) depth. The South Kawishiwi is one of several minor mafic intrusions that constitute the western margin of the Duluth Complex near Ely, MN (Fig. 1). It is com¬prised of a 70.1- to 350.5-m (230- to 1150-ft) thick sul¬fide-bearing basal unit of troctolite with minor amounts of anorthosite, norite, picrite, and oxide layers overlain by a troctolite unit with interlayered anorthosite (Bonnichsen et al., 1980; Foose, 1984; and Foose and Weiblen, 1986). The basal unit, in which the Pt-Pd zone is found, is markedly heterogeneous in rock type, lacking any coherent internal stratigraphy, and shows evidence of both pre- and post-consolidation faulting (Foose and Weiblen, 1986). Geochemistry Chemical analyses were made on 0.3-m (1-ft) intervals of crushed drill core material (1/4 core, BX size) at 731.5 to 740.7 m (2400 to 2430 ft) depth and the results are presented in Fig. 2. The analytical techniques used were atomic absorption spectrometry for silver, chromium, copper, and nickel; a coulometric titration method for sulfur; and a combined fire assay-DC plasma technique for gold, palladium, and platinum. Figure 2 shows the significant enrichment of platinum and palladium at 734 to 737 m (2408 to 2418 ft) depth; it corresponds to a stratigraphic interval rich in oxide minerals. Average values for platinum and palladium contents over the 3-m (10-ft) interval are 2520 and 2580 ppb, respectively, or 5.1 g/t (0.15 oz per st) platinum plus palladium. Platinum plus palladium contents from individual 0.3-m (1-ft) intervals are as high as 9120 ppb or 9.1 g/t (0.27 oz per st) and average 7.4 g/t (0.22 oz per st) in a 1.5-m (5-ft) interval in the richest part of the zone. The Pt-to-Pd ratio is nearly 1:1 over the entire 9.1-m (30-ft) interval and the platinum and palladium correlate closely with chromium, which ranges from 1.9% to 5.3%. Copper, nickel, and sulfur contents for the drill core interval are also given in Fig. 2. In¬terestingly, the Pt-Pd high corresponds to a depletion in copper, nickel, and sulfur. Mineralogy of the Pt-Pd zone The Pt-Pd zone occurs within an oxide-rich zone or layer that consists essentially of oxide minerals, plagioclase, and olivine. The oxides may constitute as

Jan 1, 1987

By Stuart M. Jones

This paper describes the state of the art of grinding in the Copper Industry today including descriptions of the largest equipment and design features which allow processing of as much as 100,000 mtpd in a single mill line. We include a typical flowsheet, control philosophies, and maintenance techniques which result in low cost production which is essential in today's market.

Jan 1, 1999

By John Manka

Emulsion explosives consist of an aqueous oxidizer phase, a fuel phase, and an emulsifier. The ability to use lower-cost sources for any of these raw materials presents an obvious economic advantage to emulsion manufacturers. This paper focuses on using low cost waste drain oils as the fuel phase in emulsion explosive applications. Laboratory studies showed that emulsions made from waste drain oils and agricultural ammonium nitrate prills were usable for emulsion explosives though their shear stability was weak. Customer field results proved that waste crankcase drain oil could replace half of the virgin diesel fuel in emulsion explosives to make an effective emulsion explosive product with a very low cost.

Jan 1, 2003

By L. W. Cope

Cuba is a mineral rich area, and the Cuban government is encouraging mining investment in the country. Joint ventures with government entities are encouraged. This paper will give some insights into the laws and regulations, and the agencies to contact for investment and development. The present-day situation of the US sanctions against Cuba will be covered.

Jan 1, 2004

Jan 1, 1970

By Walter Campos, Yuri Gallegos, Sául Vigil

El proyecto Educación Digital Rural ha sido analizado con instrumentos de corte cuantitativo, a través de la aplicación de encuestas a docentes y personal directivo de escuelas del área de influencia directa de Minera las Bambas; además, del uso de la técnica de análisis documental sobre el estado de las matrículas y situación final de estudiantes en el año 2020 y 2021 (Hernández et al., 2020). Los resultados muestran que la intervención ha evidenciado la importancia de tener el personal capacitado sobre el aprovechamiento de las tecnologías digitales en el proceso educativo y sobre la intervención clave del liderazgo del directivo para orientar el trabajo docente y asegurar condiciones que permitieron dar continuidad al servicio educativo en las II.EE. rurales de Fuerabamba, Huancuire y Pamputa.

Sep 30, 2022

By M. Zuckerberg, E. Mader, R. Pasyar

We describe a new software product designed for the net present value optimization of multi-open-pit blended ore operations in which it is desired and/or necessary to dump some or all of the waste rock produced in the course of operations back into the voids created in the process of ore extraction. The software product simultaneously decides over the entire life-of-mine which material to mine in which year, once mined what to do with it, and where to put that material which it has decided to waste, all subject to annual blend and capacity constraints.

Jan 1, 2007

By Joseph W. Leonard

Evidence is presented to show that certain coals can be super-cleaned, using present coal preparation processes, to reduce sulfur below levels that are commonly believed to be possible. The evidence points to the need to develop continuous sorting methods by which coal coming from a mine can be segregated so that different raw coal types can be processed separately to produce a super-clean coal in addition to coals cleaned to more common levels of sulfur. Evidence is presented and techniques discussed that may be applicable for making the method feasible.

Jan 1, 1976

By R. P. Smith

The diffusivity of carbon in iron, cobalt, and alloys of 89.7 and 79.3 wt pct Co has been determined by a decarburization method for the temperature range 850° to 1100°C. The Plots of log D us 1/T for the two Fe-Co alloys are linear through the region of the Curie temperature, showing that, unlike some cases of substitutional diffusion, carbon diffusion in these alloys is not affected by electron spin order. RECENT investigations1-' have shown that for substitutional diffusion in iron the change in diffusivity with temperature does not follow an Arrhenius equation, at temperatures near the Curie temperature. Data on the diffusivity of carbon in a iron5"9 indicate that this anomaly does not exist for interstitial diffusion; however, this has not been definitely established. Since cobalt and Fe-Co alloys, 80 to 100 pct Co, have Curie temperatures in a temperature range convenient for carbon-diffusion measurements they are suitable systems for studying the relation of interstitial diffusion and the Curie temperature. EXPERIMENTAL The carbon diffusivity, D, was determined by a decarburization method. The diffusion cylinders, made from small vacuum melts of electrolytic cobalt and plastiron, were about 0.76 cm diam and 6.3 cm long. A small amount of carbon was added to each melt to keep the oxygen content as low as possible. The cylinders were first treated with a hydrogen-3 pct water vapor mixture at 1100°C to constant weight, then carburized to the desired initial carbon content with a suitable CO-C02 gas mix-

Jan 1, 1964

By Ian J. Graham

Brothers volcano, in the southern Kermadec Arc, is host to two hydrothermal vent fields with very different geology, permeability, vent fluid compositions and mineralogy (see de Ronde et al. and Ditchburn et al. this volume). The NW caldera site contains mineral deposits (sulfide chimneys and crusts), which are either Cu-rich (?magmatic?) or, more commonly, Zn-rich (?epithermal?). The lower cone site, in contrast, is characterized by native sulfur mounds and spires. It has been proposed (see de Ronde et al. this volume) that the metals, especially Cu and possibly also Au, enter the hydrothermal system via injection and degassing of magma and/or the dissolution of metal-rich glasses. They are then transported rapidly upwards via magmatic volatiles along long (c. 2.5 km), narrow (c. 300 m diameter) pipes, consistent with evidence of vent fluids forming at higher than hydrostatic pressures, at relatively shallow depths. The NW caldera and cone sites may represent stages along a continuum between magmatic-hydrothermal and water/rock-dominated end-members. In this context, investigation of melt inclusions in conjunction with other geochemical and petrological research was carried out to ascertain the metal transporting conditions that may have led to mineral deposition and ore formation. Sixteen melt inclusions in plagioclase were analyzed for their chemical compositions from a typical cone dacite sample using LA-ICPMS at the University of Tasmania. The inclusions are typically glassy and commonly occur with other inclusions such as apatite, clinopyroxene, zircon, magnetite, sulfides and/or low-density fluids (Fig. 1). Major (XRF) and trace element (ICPMS) analyses were performed on whole rock samples collected during the 2005 Shinkai 6500 expedition. Haase et al., (2006) has also reported EPMA glass analyses from cone dacites, which may be used for comparison (Table 1). [ ]

Jan 1, 2010

By L. W. Page

PrEvious to the introduction of the motor vehicle the broken stone or macadam' road met the conditions of rural horse-drawn traffic better than any other type of road, but under fast motor traffic it has been proved to be quite unsatisfactory, and necessitates high maintenance charges. Such a road depends for its success upon the fact that the rock dust fills the voids between the stones and acts as a cement or binder. Under ideal conditions it should be constructed of rock so suited to the volume and character of horse traffic that only enough fine dust is worn from the stones of which the road is composed to take the place of that carried off by wind and rain; and when these conditions are met, the fine dust resulting from the wear of traffic forms with the stone a smooth, impervious shell, shedding the surface water and protecting the foundation. With increase in the number and speed of motor vehicles, however, it was soon found that the cost of maintenance also increased, until at the present day highway engineers consider the old method of constructing and maintaining broken-stone roads increasingly inadequate, and are introducing every known type of binding material other than rock dust to cement the stone together. Among the most prominent types of products in use are those produced from our various petroleums. That the value of modern methods of road preservation was appreciated in this country much earlier than we have been accustomed to believe is demonstrated by the recent revival of an old patent which was granted to one John Martineau, of Elbridge, N. Y., in 1834. Petroleum had, of course, not been discovered at that time, but he claims as his invention and improvement "The application of tar, turpentine, or any of that class of tenacious, cohesive substances, reduced before use to a fluid state, and that state used as a cement, to apply to, and combine with sand, gravel, pebbles, and pulverized stone, such as is used for a Mc-Adam road, or cobble stone, the interstices of coarser material being in all cases filled,'as well as may be, with sand and gravel and cemented with tar or turpentine, to form the wearing face or surface of streets,

Jan 1, 1915

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By A. McLean, D. W. Gomersall, R. G. Ward

An experimental study has been made of the solubility of nitrogen in liquid iron and liquid Fe-C alloys using levitation melting and a rapid quenching device. Iron alloy droplets were equilibrated with nitrogen gas at 1 atm pressure, quenched, and analyzed. Previous techniques for studying the Fe-C-N system have produced data which me in marked disagreement. This disagreement is due largely to errors caused by reaction between the molten alloy and the crucible material. With the levitation procedure, errors from this source have been eliminated and precise solubility data obtained for temperatures between 1450° and 1750°C. C-N interactions in molten iron have been expressed in terms of first- and second-order free energy, enthalpy, and entropy parameters. ALTHOUGH the solubility of nitrogen in iron base alloys is in general small, the effects of nitrogen on the properties of steel may be quite profound. For most purposes nitrogen in finished steels is undesirable, particularly in the low-carbon grades, since on cooling to room temperature the solubility limit of nitrogen in the steel may be exceeded and this can lead to embrittlement and loss of ductility on aging. On the other hand, nitrogen can improve the work-hardening properties and machinability of steels while in certain stainless grades nitrogen is important in order to stabilize the austenite phase. It is, therefore, desirable that one should be able to predict the solubility of nitrogen in liquid iron alloys. To do this, information is required concerning the interactions between nitrogen and the various alloying elements which may be present in liquid iron. There have been several investigations of these effects in recent years1"7 and the interactions between nitrogen and many elements dissolved in liquid iron are now known to a high degree of precision at steel-making temperatures. Unfortunately, a number of iron alloy systems which are of interest in steelmaking have been difficult to deal with by the experimental techniques generally used for this type of investigation. Among the most important of these are the Fe-C alloys. In the past, two methods have been widely used for determining nitrogen solubilities: the Sieverts' technique, in which the amount of nitrogen required to saturate a given mass of liquid metal at a particular temperature and pressure is measured volumetrically, and the sampled-bath technique in which liquid metal held in a crucible is equilibrated with a gas phase containing a known partial pressure of nitrogen, and samples drawn from the melt are quenched and analyzed. These two methods have been discussed in detail elsewhere.5,8 With the Sieverts' technique, errors may be introduced from the following sources: i) Gas adsorption on metal films which have condensed on the cooler parts of the reaction chamber. ii) Uncertainty in the determination of "hot volume" calibrations. iii) Crucible-melt interaction, particularly if a gaseous reaction product is formed or if the melt becomes contaminated with material from the crucible walls. The sampled-bath method may also suffer from errors due to reaction between the melt and the crucible material. In addition, there is the possibility that gas may be lost from the sample during solidification and cooling. In the present investigation, the solubility of nitrogen in liquid iron alloys has been studied by means of a new technique based on the use of levitation melting equipment and a rapid quenching device. In addition to the fact that problems of the type outlined above are avoided, this particular approach has the following advantages: i) The high-frequency current induces vigorous stirring within the levitated droplet so that gas-metal equilibration is rapidly attained. ii) The gas phase surrounding the melt can be changed very quickly and is easily controlled. For example, a droplet may be levitated in helium, deoxidized in hydrogen, equilibrated with nitrogen, and quenched, within a period of 15 min. ii) Melts can be readily under cooled or superheated, thus extending the effective temperature range of an investigation and allowing temperature-dependent data to be determined with a high degree of precision. Excellent reviews of levitation melting techniques and their application to physical-chemistry studies at high temperature have been published recently by Jenkins et al.,9 Peifer,10 and Rostron.11 In the present investigation a levitation melting technique has been used to obtain data for the solubility of nitrogen in pure liquid iron and liquid Fe-C alloys at temperatures between 1450° and 1750°C. The solution of nitrogen in liquid iron can be described by the reaction:

Jan 1, 1969

By Chris L. Powell, Russell J. Denny

"The remotely located Cockatoo Island iron ore mine off the Kimberley coast in the northwest of Western Australia has been in operation since 1951. The mine was recently expanded up to about 50 m (165 ft) below sea level using staged construction to create a rockfill seawall around the open cut mining operation. Late in 2013, to allow expansion of subsea iron ore mining operations, Wagstaff Piling was engaged to install a seepage barrier through the rockfill seawall and into the underlying seabed sediments.Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of subsea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansions that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative seepage barrier solution using a grout curtain was selected to provide the necessary cutoff to allow access to highgrade ore, while protecting the mine from inundation by the sea.Seawall ConceptThe open cut subsea mining operation consisted of a 3 km (1.9 mi) long narrow pit along the south side of Cockatoo Island that extended to depths of about 50 m (165 ft) below sea level, and were exposed to the open sea on the south side of the pit. Massive tidal variations of more than 10.5 m (34.5 ft) required a seawall founded on the seabed, extending upwards to RL+13, to safely protect the pit from the high tide level rising to above RL+10."

Jan 1, 2017