Search Documents

By D. S. van Vuuren

Industrial production of titanium occurs via the batch-wise reduction of titanium tetrachloride (TiCl4) with a reducing metal, being magnesium in the Kroll process, or sodium in the Hunter process. In the search for low cost titanium, the CSIR is developing a continuous process to produce titanium powder directly via metallothermic reduction of TiCl4 in molten salt, dubbed the CSIR-Ti process. The move to a continuous process has been attempted by a number of organizations, but was until now always met with failure, due in no small part to challenges inherent in the process chemistry. The reaction between TiCl4 and the reducing metal can occur directly, when TiCl4 or any titanium sub-chlorides present, comes into contact with suspended or dissolved reducing metal. The reaction can also occur indirectly, without any physical contact between the reacting species, via an electronically mediated mechanism. The reaction mechanism via electronic mediation can cause TiCl4 to react at the outlet of the feed port, rapidly causing blockages of the TiCl4 feed line. The electrical conductivity of the metal reactor can also cause the electronically mediated reaction to favour the formation of titanium sponge on the reactor walls and internals, rather than titanium powder. Various methods were investigated to overcome the problem of blockages in the TiCl4 feed line, e.g. mechanical removal, sonic velocities, dilution of the TiCl4 and the use of ceramic feed lines. This article discusses problems experienced with the continuous feeding of reagents, and various methods attempted are shown and discussed. Information is also given on the morphology, chemical composition and suitability of the final titanium powder for powder metallurgical application as presently produced by the CSIR-Ti process. Keywords Titanium dioxide, titanium nitride, carbo-thermic reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By C. D. Rugen

GROUND raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grindability characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. CHARACTER OF GROUND RAW MIX (KILN FEED) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size, whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1945

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By Maurice Deul, Herbert H. Fields, John H. Perry

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (2), and pipeline--quality gas was introduced into a commercial pipeline. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed.

Jan 1, 1975

By E. P. Youngman

This digest, based upon a translation" of certain portions of the 1930 law, covers the pertinent points of what has been termed "The New Mining Law of Luxemburg," the Grand Ducal Order (Arrêté) of April 26, 1930, concerning the exploitation of "mines, minières, and carrières, 4 and abrogating the order of January 2, 1891, concerning the same subject." The Duchy of Luxemburg, which between 1735 and 1815 was French, adopted as its basic mining law the French Law of April 21, 1810, and an Imperial Decree of January 3, 1813. The Luxemburg Government later supplemented and modified this legislation by the laws of June 12, 1874, April 30, 1890, and May 10, 1898, which, with article 36 of the Constitution, are to be taken into consideration in a complete survey of mining legislation. The order of

Apr 1, 1933

By Alberto Giles P

El presente texto señala el sistema de tolva de almacenamiento intermedio en el yacimiento minero, donde los volquetes depositan sus cargas y desde este espacio, el material se descarga a los trenes. En este sentido, la tolva fue construída y diseñada en Toquepala, adquiriendo un sistema de carguío más eficiente y aumentando la productividad de la mina.

Oct 14, 1980

One of the newest and most modern surface mining operations in the East is gathering steam at Mapco Inc.'s Martiki mine in anticipation of yielding 2.7 million tons (3 million st) of coal annually.

Jan 10, 1977

Jan 1, 1955

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United States and publishes economic data on the industry, based upon reports from producers. This publication lists all producers that reported commercial production to the Bureau for 1959. The companies named herein represent virtually all commercial producers of peat. A few companies, however, may not have been canvassed or failed to respond, as tine survey is voluntary For producers, arid the industry has many small operations that operate intermittently. No consideration was given to the quantities of peat produced and output of the various companies listed ranged from less than 100 tons to more than 50,000 tons, Peat is included in the Bureau's annual surveys of the mineral industries because, technically, peat is a fuel. Although none is used for fuel in the United States, peat is a potential source of energy and one of our large mineral resources. The domestic peat industry produces peat chiefly for use as a soil amendment. The industry has expanded rapidly during the past decade with active operations increasing from 45 in 1947-49 4/ to 105 in 1959. Output during this period has increased 218 percent, rising from 131,782 net tons to 419,460 net tons.

Jan 1, 1960

By Julian Malnic

The nascent marine mining sector appears to be now at a point of critical mass with the prospect of mining seafloor massive sulphide deposits at some time in the coming few years an inevitability. Julian Malnic makes comments from his experience base as an entrepreneur and founder of Nautilus Minerals Inc. in 1995 and will speak from an independent viewpoint of the commercial setting of the status quo of the proto-industry and the major factors likely to have major influence over its future. The presentation questions these factors and the role they will play. Do we need metals from the oceans? Understanding the competing and established terrestrial sources of each commodity is essential in comprehending how a marine competitor can profit. What are the rates of discovery for marine minerals? At what point will marine explorers start to impact the terrestrial copper and zinc exploration sector? The advance of technology is important in finding, imaging and mining SMS deposits, but which new technologies offer the advantage to mining in the ocean and which to mining on the land? Several competitors have now joined Nautilus as competitors to this global pioneer of SMS exploration/production. The membership of the major miners in the marine sector is growing steadily with important relationships developing but many have not put a toe in the water yet. A path of increasing width is opening to commercialization of SMS miners but crusts and nodules, as bearers of copper ? also found in SMS, and nickel ? also found in widespread nickel laterite deposits on land, are unlikely, in this perspective, to be winners this century unless highly valued minor metals are targeted.

Jan 1, 2008

By P. E. Senseny

INTRODUCTION Massive hydraulic fractures have been used since 1949 in the petroleum industry to enhance production rates and increase recoverable reserves. Currently, a research program, the Multi-Well Experiment, is underway to develop the understanding and technology to a1 low economic production of the large gas reserves of the low permeability, lenticular sandstone formations in the western U.S. (Atkinson, et al, 1981; Northrop and Sattler, 1983). Use of state- of-the-art hydraulic fracturing techniques is a part of this investigation. As a portion of an extensive core program in support of this experiment (Sattler, 1983), fracture toughness has been determined for 56 sandstone, shale, mudstone, or siltstone horizons from three wells in the Piceance Basin. The role of fracture toughness in hydraulic fracturing is not well understood because other factors, such as in situ stress, dominate fracture geometry and containment. Rubin (1983) concluded from analysis of his laboratory hydrofracture experiments that fracture toughness should be included in design and numerical simulation of hydraulic fractures. However, van Eekelen (1982) contends that the stress intensity at the crack front should be so much greater than the fracture toughness of the rock that toughness can have no importance. Generally, fracture toughness and other material properties, such as elastic moduli and permeability, are thought to be of secondary importance in determining fracture geometry and containment. In spite of this, there is a need to acquire a more quantitative understanding of their importance for accurate design and simulation calculations. Analysis of fracture geometry and containment data from hydraulic fracturing experiments carried out in formations where fracture toughness and other rock properties are

Jan 1, 1984

By Thuli AJ

Copper concentrate from Bougainville's copper mine located on the west slope of the Crown Prince Range on Bougainville island, is pumped 27 km to the filter and drying plant at Anewa Bay for preparation and storage prior to shipment to overseas customers. Prior to shipment the thickened concentrate slurry is passed through a test loop to check that its consistency and pH are acceptable for transportation through the main pipe line. The Bougainville pipe line is unique since it is the world's first copper concentrate system. where slurry is pumped an appreciable distance against a high head,

Jan 1, 1975

By G. S. Hume

IN. THE autumn of 1922, British Petroleums Ltd. found oil of 14° Baumé in a sand 17 ft. thick in its. No. 2 well at Wainwright, 120 miles southeast of Edmonton. This greatly encouraged drilling in the Wainwright-Irma area and this past summer several wells were started, three of which are now completed and the others still being drilled. Of the three completed, No. 4 British Petroleums contains oil; No. 3 British Petroleums gave a show of oil but so far has not given much hope, of becoming a commercial producer; and No. 1 Maple Leaf Co., as now finished, is a. gas well with a daily flow of gas of about 2,500,000 cu. ft. at a closed pressure of 700 lb. An oil sand is reported to have been encountered below the producing gas horizon in the Maple Leaf well but has not been tested. Operations on this well have been suspended for the winter. The Geological Survey of Canada this past summer undertook a geological investigation of this area with the object of defining the structures with which the oil and gas are associated. The structure underlying this portion of the plains was supposed to be a terrace with the western edge dipping into the Alberta syncline and with a monoclinal structure to the east. By accurate leveling on known geological horizons on this terrace, a number of gentle folds were located and -it is in these folds that the oil and gas are found. At the British Petroleums Nos. 2 and 4 oil wells, the western flank of the fold has a gentle dip of only a few feet to the mile to the southwest whereas the strata on the eastern flank dip to the northeast about 40 ft. in ½ mile, the strike of the fold being northwest and southeast. How far oil will be found down the gentle southwest dip is unknown but probably the productive part of the fold will not exceed 1 mile in width, and possibly less. No. 3 British Petroleums well is on the strike of the fold 1 mile southeast of the two oil wells. The sand that was productive in Nos. 2 and 4 wells was not present in this well or, if present, was very thin and unproductive. Two other sand horizons, however, were encountered. The upper of these

Jan 3, 1925

By H. H. Kellogg

An invitation to address you on the occasion of the one-hundredth anniversary of AIME represents an honor, a challenge and an opportunity: an honor that you judge me worthy; a challenge that I present to you a picture of extractive metallurgy in the years ahead that contains some ideas of value; and finally, an opportunity for me to express some deeply felt beliefs about our profession and our industry. My topic concerns the technology of metal production in the future - the processes, new and old, that will be used to extract metals. The nature of these processes will be shaped by many forces - some technical, some economic, some political or social. A forecast of future technology must recognize the role of each of these forces, and I have endeavored to do this in the analysis that follows. In brief, my outline consists of an analysis of the forces (perhaps better called "problems") that will influence the future of our industry, followed by consideration of likely lines of technological development to meet them. Let me dwell for a moment on the nature of this industry and the profession that serves it. I have been engaged in the profession of extractive metallurgy - teaching, researching and consulting - for 30 years. I have always found the subject stimulating and rife with challenges of a scientific, engineering, economic and socio-political nature. It is a big subject - it encompasses most of the elements of periodic table; we measure the U. S. production of six metals in millions of tons per year; new plant costs range to $100 million and more. The supply of metals from our extractive plants plays an essential role in our modern industrial economy. We could do without DDT, or phosphate detergents or 300-page Sunday newspapers; we cannot do without a huge and increasing supply of metals. The Basic Goal of Extractive Metallurgy Understanding of some basic forces that shape this industry can be gained by consideration of the question: What determines the utility of metals to man? We think immediately of the inherent properties of metals - strength, ductility, electrical conductivity and so forth - but these tell only part of the story. Metal price and the available supply play equally

Jan 1, 1971

By M J. Nugus

A substantial cost is invested into the data collection phase of any exploration or development program; notwithstanding, it is impractical to expect a database of information can be collated to ensure a perfect geological interpretation. The question then becomes, is there a possible alternative interpretation and what is the likely impact of the variations? Modelling in 2005, of the Cosmo lode at Sunrise Dam Gold Mine, Western Australia led to consideration of the philosophical implications associated with resource management. It was concluded that several plausible geological models could be constructed from the known geological database. To varying degrees, this predicament is common to all geological reconstructions, as several alternative geological models can be generated at almost any stage that will impact on the resultant resource estimation and mine plan. The significance of that variation and the associated risk of multiple geological models (MGMs) requires due consideration. What is being suggested is that using plausible multiple geological models advances the holistic understanding of a mineral deposit within the bounds of the data collected, providing fluidity for updating geological knowledge and building inherent variability into the design and planning departments where variations of the geological models may materially impact on the resource performance.

Jan 1, 2006

A shift in the present day oil exploration scenario from West Coast can be foreseen keeping in mind peak of exploration in Cambay Basin and fast pace of development in Bombay High and its associated fields by the end of this century. Shifts in exploration from structural traps to stratigraphic traps, techno- logical development to drill in deep waters, improving economic situation for oil ventures and proven oil and gas potential of East Coast basins suggest that Indian oil explorat- ion scene will be at its peak along east coast during early 21st century. Hydrocarbon shows in Poonch and Jawalamukhi in Punjab Basin, improvements in drilling to greater depths, better seismic data aquisition, good source rock potential of Subathus and its equivalents and large geologi- cally mapped structures will reopen new avenues for explorationists. Not much exploration effort has been put up so far in Ganga Basin. Keeping in mind size of the basin, sedimentary thickness involved, presence of algal matter deposited in shallow marine environment & higher hydrocarbon indications warrant active exploration. Gondwanas in India having such a large sedimentary area can not be ignored keeping in view generation and production from the non marine sediments of Kenya, Chad, Sudan, Gadon and China. Gondwanas become all the more important in view of gas production from their equivalents-Karoos in Ethiopia and South Africa. In all, above mentioned changes can be predicted in Indian oil exploration scenario during 21st century.

Jan 1, 1986

On the basis of the data known on formation, characteristics and stability of solute heavy non-ferrous metals under different temperature and pressure conditions and different concentrations of substances dissolved it is found to be possible to obtain a condition of mineral formation resulting in selective production of free-floating minerals. This process of forced mineral formation has been taken as a basis of new methods of refractory copper raw materials concentration, complex processing of lead dust from copper smelting plants, lead flotation tailings final concentration and of those of polymetallic ores concentration. This list of effective utilisation of the process is not exhaustive (Bekturganov Abishev and Shkodin, 1987; Bekturganov and Sim, 1987; Bekturganov, 1988; Abishev and Bekturganov, 1989; Bekturganov, 1989a). To understand the character of the sulphurising thermodynamic and kinetic examination have been done. Analysis of conditions of the newly formed mineral associations formation and stability facilitates the elaboration of methods of improvement of results of the valuable components selective separation.

Jan 1, 1993

By L. C. Reese

The ultimate resistance against a rigid cylinder which is moved laterally in a cohesionless soil is a function of the geometry of the cylinder and the properties of the soil. An approximate method is developed for computing this resistance and is tested against results of laboratory experiments. Satisfactory agreement between the method and experiment was obtained. Not only was the ultimate resistance against the cylinder measured, but measurements were made of the shape of the rupture surfaces. These measurements should allow the development of a more rigorous computation procedure. INTRODUCTION A critical aspect in the design of offshore drilling platforms is assuring the stability of the platform during a hurricane. The large horizontal loads from waves and wind make a severe loading condition. Piles are generally employed as the foundation since they can be effective in resisting both horizontal and vertical loads. Spuds are sometimes used with a mat foundation, where the spuds are designed principally to resist horizontal loads and the mat designed principally to resist vertical loads. The research reported in this paper is related to one aspect of the problem of laterally loaded piles or spuds in sand. The complete solution to the problem of the laterally loaded pile in sand would require the prediction of soil resistance against the pile as a function of pile deflection; only the ultimate resistance against short piles is considered in this paper. A considerable amount of additional research will be necessary in order to obtain a complete solution to the problem of the laterally loaded pile in sand; however, the work reported here should be useful as a guide in the performance of some of the additional research. ULTIMATE LATERAL RESISTANCE AGAINST A LONG FALL IN SAND To aid in the understanding of the theory which is developed for a cylinder, the theory for earth pressure against a wall is reviewed. In Fig. l(a), a long wall of height H is shown embedded in soil. Soil resistance will develop as the wall is deflected, and the soil resistance will increase with deflection until some limiting value is reached. In this discussion, and those following, it is assumed that all points on the wall deflect equal amounts. A possible shape of the real curve which relates soil resistance to deflection is shown by the dashed line in Fig. l(b); however, as a means of simplifying the discussion, an idealized curve (shown by the unbroken lines) is drawn. If such a wall as this were furnishing the horizontal support for an offshore structure, the dashed curve in Fig. 1 would be the information needed in performing a foundation analysis, with the idealized curve possibly being an acceptable substitute. For the idealized curve, the soil resistance is linear with deflection for the early portion of the curve such that

Papers in Classes A-Metal Mining, B-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Papers in Classes C-Iron and Steel Division, D Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. Papers in Class G Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J Mineral Industry Education Division, Mining Administration, and L-Geophysics, are issued as separate pamphlets. Contributions are papers that when printed or mimeographed are available, but only on request.

Jan 1, 1946

By N. N. Breyer, W. R. Warke, S. Dinda

A model for the low-temperature peak, LTP, in fcc metals is presented. In high stacking fault energy metals, e.g., aluminum and nickel, it is proposed that a reversible dislocation glide and climb process might give rise to the observed high relaxation strengths and activation energies equivalent to volume self-diffusion values. In low stacking fault energy metals such as copper, gold, and silver, dislocation climb is energetically unfavorable at T < 0.5 Tm and the relaxation process is therefore mainly one of reversible glide. This model is used to explain the effect of a change in grain size and impurities on the LTP. THE low-temperature grain boundary damping peak, LTP, in spectroscopically pure aluminum,&apos; copper,17&apos; gold,2 nickel,3 and silver4 has recently been the subject of a detailed investigation by our laboratory. The main results are summarized in Table I. An empirical relationship was found between the peak relaxation strength, AE, and the width of the dissociated dislocation, do,* given by: do = µa2/24p? (Ref. 5) [I] where p is the shear modulus, y is the stacking fault energy,6-8 and a is the lattice parameter, Table 11. 4E is plotted against do in Fig. 1. Two regions are apparent: region (a)! which contains all but one of the metals, where AE decreases linearly with increasing do, i.e,, AE 1/do; and region (b), where ?E is approximately independent of do. A similar trend is observed when the ratio Qp/QL is plotted as a function of do, Fig. 2. (Qp and Ql are the activation energies for the peak and for lattice diffusion, respectively). In the past, when Qp and QL were found to be comparable, the relaxation peak was explained in terms of grain boundary sliding.10 The equivalence of Q, and Qb. the activation energy for grain boundary diffusion, prompted the suggestion that it was a consequence of reversible grain boundary migration on an atomic scale." A new model for the LTP, which is based on the experimental relationships in Figs. 1 and 2, is presented. In region (a) it is suggested that stress relaxation occurs through the reversible glide and climb of grain boundary dislocations; in region (b) only reversible glide can take place. The resultant effect on the grain boundary might be sliding or "a bowing out", but, since the total distance moved will be 50A, the atomic movements are considered of primary im- portance. It must be emphasized that this is only a qualitative model, but at the moment it appears the most likely way to explain the widely varying, but re-

Jan 1, 1969